Borla S-Type Cat-Back Exhaust System for 2005-2008 Chevrolet Corvette | BOR162165
Or 3 interest-free payments of $629.00 with Affirm.
- Not your vehicle? See all Borla S-Type Cat-Back Exhaust Systems
- Iconic Borla sound without too much noise
- Catalog Number: Borla 140128
- Fits: Chevrolet Corvette (check fitment chart for compatibility)
Borla S-Type Cat-Back Exhaust System for 2005-2008 Chevrolet Corvette | 140128
Product Specifications:
- Diameter (IN): 2-1/2 Inch
- Exhaust Tip Material: Stainless Steel
- Exhaust Tip Size (IN): 4 Inch
- Exhaust Tip Type: Round
- Exhaust Type: Dual
- Exit Position: Split Rear Exit
- Includes Exhaust Pipe Muffler Delete: No
- Includes Exhaust Tip: Yes
- Includes Hardware: Yes
- Includes Muffler: Yes
- Material: Stainless Steel
- Muffler Brand: Borla Brand
- Muffler Configuration: Single Inlet And Single Outlet
- Muffler Quantity: 2
- Outlet Type: Quad
- Required Welding: No
- Sound Level: Aggressive Plus
- Type: Cat-Back
Fitment Chart:
| Years | Make | Model | Submodel | Liters | Cylinders | Notes |
|---|---|---|---|---|---|---|
| 2008 | Chevrolet | Corvette | Base | 6.2L | V8 | Singe 2.5 in. Into Muffler Exiting Dual 2 in. Out; Incl. Conn. Pipes/Mufflers/Hdw/4 in. x 7 in. Dual Round Rolled Angle-Cut Tip; Split Rear Exit; 50 State Legal / California Emissions Compliant; Includes Paddle Shift~T-304 Stainless Steel~w/X-Pipe |
| 2006-2007 | Chevrolet | Corvette | Base | 6.0L | V8 | Singe 2.5 in. Into Muffler Exiting Dual 2 in. Out; Incl. Conn. Pipes/Mufflers/Hdw/4 in. x 7 in. Dual Round Rolled Angle-Cut Tip; Split Rear Exit; 50 State Legal / California Emissions Compliant; Includes Paddle Shift~T-304 Stainless Steel~w/X-Pipe |
| 2005 | Chevrolet | Corvette | 6.0L | V8 | Singe 2.5 in. Into Muffler Exiting Dual 2 in. Out; Incl. Conn. Pipes/Mufflers/Hdw/4 in. x 7 in. Dual Round Rolled Angle-Cut Tip; Split Rear Exit; 50 State Legal / California Emissions Compliant; Includes Paddle Shift~T-304 Stainless Steel~w/X-Pipe |
S-type Chevrolet Corvette cat-back exhaust system
Borla 140128 S-Type Cat-Back Exhaust System is made primarily to improve the performance of your Chevrolet Corvette by increasing the horsepower and torque. On top of that, the exhaust system also improves exhaust tone. What sets it apart from the Borla ATAK Cat-Back is that its volume is 25%-30% lower than ATAK, and so the best choice for people seeking to get the iconic Borla tone but not make too much noise. Its sound is, however, more aggressive than Borla Touring.
Constructed from stainless steel
Constructed from stainless steel, you can forget about any occurrence of corrosion or rust since it has been built to resist such elements. The steel is also tough and will hold up well against daily torture by other road elements.
Mandrel-bent stainless steel tubes
The mandrel-bent tubes of this exhaust system enable it to allow a smooth and fast flow of exhaust gases without causing any restrictions.
Patented straight-through muffler design
Borla 140128 S-Type Cat-Back Exhaust System uses a patented straight-through muffler and this helps reduce back pressure and improve performance of your Chevrolet Corvette.
Polished exhaust tips
The polished exhaust tips will complement your exterior looks. They extend a few inches longer than the lower, rear side of your Chevrolet Corvette and expose their flawless finish. The tips are also well treated to resist damage.
Improves fuel economy
Using this exhaust system does not just improve horsepower and sound, but it also improves fuel economy when you are driving at cruising speed.
One Million Mile Warranty
Borla 140128 S-Type Cat-Back Exhaust System is protected by a one million mile warranty. This is an assurance that it will work without any defects in workmanship or material.
Made in the USA
Borla manufactures its products right here in the USA. It employs the best experts who use world-class quality material and cutting-edge technology to provide a blend of quality, durability, and top performance.