{"title":"Brake \u003e Drums and Rotors","description":"\u003cp\u003eRotors and drums are the friction surfaces your brake pads and shoes clamp against to stop your vehicle — and they wear down every time you brake. Rotors typically last 30,000–70,000 miles depending on driving habits, rotor thickness, and whether pads were replaced on time; drums generally last 150,000–200,000 miles but can warp or score well before that. You'll know they're due when you feel vibration through the pedal, hear metal-on-metal grinding, or measure below minimum thickness spec (stamped on the rotor or drum hat). When buying, match the exact rotor diameter, hat depth, and lug pattern to your application — a 1mm difference in hat depth can cause fitment issues. OEM replacements maintain factory performance; slotted or drilled aftermarket rotors improve heat dissipation for tow vehicles or performance driving but may wear pads faster. Coated rotors resist rust significantly better than bare iron, especially if the vehicle sits for extended periods.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePulsating or vibrating brake pedal\u003c\/strong\u003e — A pedal that pulses under braking almost always indicates a warped rotor. Lateral runout beyond 0.003–0.005 inches (spec varies by application) causes the pads to bounce against an uneven surface.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrinding or metal-on-metal noise when braking\u003c\/strong\u003e — Once pads wear through their material, the backing plate contacts the rotor directly. Continued driving in this condition scores the rotor surface deeply, often making rotor replacement unavoidable even if it wasn't before.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVisible grooves or score marks on the rotor face\u003c\/strong\u003e — Grooves deeper than approximately 1.5mm indicate the friction surface is compromised. A rotor that can be measured below its discard thickness spec must be replaced — machining is not an option at that point.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVehicle pulls to one side during braking\u003c\/strong\u003e — Uneven rotor thickness or a seized caliper causing unequal contact can pull left or right under braking. If you've already ruled out caliper and pad issues, measure rotor thickness variation across multiple points.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBrake drum feels grabby or causes wheel lockup\u003c\/strong\u003e — A cracked, scored, or out-of-round drum causes inconsistent contact with the brake shoes, leading to harsh, unpredictable engagement, especially in wet conditions or on first application after sitting overnight.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRotor surface heavily rusted after extended storage\u003c\/strong\u003e — Surface rust after a few days is normal and clears with use. Pitting or flaking rust that doesn't clean up after several hard stops indicates corrosion has compromised the friction surface, particularly common in northern climates.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eShould I replace rotors in pairs, or just the worn side?\u003c\/strong\u003e Always replace rotors axle-by-axle — both fronts or both rears together. Mismatched rotor thickness or material on the same axle creates uneven braking force, which can pull the vehicle under hard stops. If one rotor is at minimum thickness, the other is close enough that single-side replacement rarely makes sense.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eAre drilled and slotted rotors worth it over standard blank rotors?\u003c\/strong\u003e For most daily drivers, a quality blank rotor from a reputable brand (Bosch, ACDelco, Raybestos, DBA) outperforms a cheap drilled\/slotted option. Slotted rotors help evacuate gas and debris under hard use — useful for trucks that tow regularly or track-driven vehicles. Fully drilled rotors can crack under repeated thermal stress and aren't recommended for aggressive use.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat else should I replace when swapping rotors?\u003c\/strong\u003e Replace brake pads at the same time — bedding new pads to old rotors (or old pads to new rotors) leads to uneven deposits and premature warping. Budget $150–$400 per axle for rotors plus pads combined, depending on vehicle and parts tier. Caliper hardware kits and brake lubricant are inexpensive add-ons that prevent noise and uneven wear going forward.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"ate-sp09114-disc-brake-rotor","title":"ATE SP09114 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP09114\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP09114 is engineered for reliable braking performance on select Mercedes-Benz and Chrysler models. Designed as a solid disc brake rotor with a rust-resistant coating, it offers durability and consistent stopping power for vehicles like the Mercedes-Benz SLK300 and Chrysler Crossfire.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 9.00 mm ensuring proper rotor life and performance\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for consistent braking\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 278.00 mm compatible with specified vehicle models\u003c\/li\u003e\n\u003cli\u003eHeight: 2.547 inches for precise fitment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid, suitable for standard braking systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to combat rust and corrosion. This coating enhances the rotor's lifespan and maintains braking efficiency over time. The SP09114 model exemplifies this approach with its full cast solid construction and rust-resistant finish, making it a practical choice for Mercedes-Benz and Chrysler vehicles requiring dependable disc brake rotors.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP09114 disc brake rotor is constructed from durable metal with a nominal thickness of 9.00 mm, ensuring it meets the necessary specifications for effective braking. Its full cast solid design provides uniform strength and heat distribution, which is critical for maintaining braking performance under various driving conditions. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, which is especially beneficial in environments prone to moisture or road salt exposure. With an outside diameter of 278 mm and a height of 2.547 inches, this rotor is designed to fit specific Mercedes-Benz models such as the SLK280, SLK320, C230, and E320, as well as Chrysler models including the Crossfire.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMercedes-Benz SLK300, SLK280, SLK230, SLK320\u003c\/li\u003e\n\u003cli\u003eMercedes-Benz C230, C240, C280\u003c\/li\u003e\n\u003cli\u003eMercedes-Benz E300, E320, 300CE, 300E, 300TE, 300TD\u003c\/li\u003e\n\u003cli\u003eChrysler Crossfire\u003c\/li\u003e\n\u003c\/ul\u003e\u003cul\u003e\n\u003cli\u003eReplaces worn or warped rotors causing brake pulsation\u003c\/li\u003e\n\u003cli\u003eAddresses rotor corrosion and surface rust issues\u003c\/li\u003e\n\u003cli\u003eRestores braking performance and pedal feel\u003c\/li\u003e\n\u003cli\u003eEliminates noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eSupports safe stopping distances on specified vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP09114, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side, simplifying the process. Verify bolt hole alignment with the vehicle hub using the 5 mm bolt hole diameter specification. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Proper torque specifications should be followed to secure the rotor without distortion.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust-resistant coating is applied to extend rotor life and reduce maintenance needs. While specific warranty details for part number SP09114 may vary, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship. Consult product documentation or authorized sources for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384124637365,"sku":"CNJW-SP09114","price":48.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP09114_Fro_e9115308-0357-4031-a284-26953340d9a3.jpg?v=1774633342"},{"product_id":"ate-sp09123-disc-brake-rotor","title":"ATE SP09123 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP09123\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP09123 is designed for reliable braking performance on select Volkswagen and Audi models. Engineered with a rust-resistant coating and solid construction, this disc brake rotor meets the demands of vehicles like the Volkswagen Beetle, Golf, Jetta, and Audi TT.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Durable metal construction\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 9.00 mm for consistent braking\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support even wear\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, for extended service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 230.00 mm\u003c\/li\u003e\n\u003cli\u003eHeight: 2.271 inches\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to reduce corrosion and extend rotor lifespan. This product line includes solid rotors constructed from full cast metal, designed to maintain structural integrity and consistent braking performance. The SP09123 rotor benefits from this coating technology, making it suitable for vehicles exposed to varying road conditions.\u003c\/p\u003e\u003ch2\u003eProduct Description and Specifications\u003c\/h2\u003e\u003cp\u003eThe SP09123 disc brake rotor is a solid, full cast metal rotor with a nominal thickness of 9.00 mm and an outside diameter of 230.00 mm. Its non-directional disc finish allows for uniform pad contact and wear, while the 5 mm bolt hole diameter ensures compatibility with the specified Volkswagen and Audi models. The rust-resistant coating helps protect the rotor surface from corrosion, which is especially beneficial for vehicles like the Volkswagen Beetle, Golf, Jetta, and Audi TT that may encounter moisture and road salt.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement rotor for Volkswagen Beetle brake systems\u003c\/li\u003e\n\u003cli\u003eSuitable for Audi TT disc brake maintenance\u003c\/li\u003e\n\u003cli\u003eUsed in Volkswagen Golf brake rotor upgrades\u003c\/li\u003e\n\u003cli\u003eCompatible with Volkswagen Jetta braking components\u003c\/li\u003e\n\u003cli\u003eAddresses rotor wear, corrosion, and braking noise issues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure proper torque specifications when mounting the rotor\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear during installation\u003c\/li\u003e\n\u003cli\u003eClean rotor surface before installation to remove any protective oils\u003c\/li\u003e\n\u003cli\u003eCheck for rotor runout to avoid vibration or uneven braking\u003c\/li\u003e\n\u003cli\u003eFollow vehicle manufacturer guidelines for brake system servicing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP09123 is manufactured to meet OEM standards for fit and function. The rust-resistant coating enhances durability, contributing to consistent braking performance over time. Warranty coverage details should be confirmed with the product documentation or supplier.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384134500533,"sku":"CNJW-SP09123","price":40.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP09123_Fro_d26b8f15-2af9-4e72-9bee-55e51d33d35c.jpg?v=1774633342"},{"product_id":"ate-sp10111-disc-brake-rotor","title":"ATE SP10111 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10111\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10111 is designed for reliable braking performance on select Volkswagen models. Engineered with a rust-resistant coating and solid construction, this disc brake rotor supports consistent stopping power and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal with rust-resistant coating\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 4 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 226.00 mm\u003c\/li\u003e\n\u003cli\u003eHeight: 3.177 mm\u003c\/li\u003e\n\u003cli\u003eType: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to reduce corrosion and extend service life. This product line includes solid rotors constructed from full cast metal, designed to meet the braking demands of vehicles like the Volkswagen Cabrio, Golf, Jetta, Passat, and Corrado. The rust-resistant coating helps maintain rotor integrity in various driving conditions.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Fitment\u003c\/h2\u003e\u003cp\u003eThe SP10111 rotor features a solid disc design with a nominal thickness of 10.00 mm and an outside diameter of 226.00 mm, suitable for Volkswagen models including the Cabrio, Golf, Jetta, Passat, and Corrado. Its full cast metal construction ensures structural strength, while the non-directional disc finish allows for flexible installation without concern for rotor orientation. The rotor’s bolt hole diameter of 4 mm matches factory specifications for secure mounting.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volkswagen Cabrio, Golf, Jetta, Passat, and Corrado\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eMitigating rust and corrosion issues on brake rotors\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency with a solid, full cast rotor\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with factory bolt hole diameter and dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with your specific Volkswagen model and year before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear and replace if necessary\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to ensure proper rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to optimize braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10111 is manufactured to meet OEM standards for fit and function. The rust-resistant coating enhances durability against environmental factors. While specific warranty details are not provided, ATE products typically adhere to industry quality controls to ensure reliable performance on Volkswagen vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384137416885,"sku":"CNJW-SP10111","price":61.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10111_Fro_11f029e7-cc1c-4316-838d-e7f870448d79.jpg?v=1774633342"},{"product_id":"ate-sp10201-disc-brake-rotor","title":"ATE SP10201 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10201\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10201 is designed for reliable braking performance on select Volkswagen and Audi models. Engineered with a rust-resistant coating and solid construction, this disc brake rotor meets the demands of vehicles like the Volkswagen Passat and Audi A6 series.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFull cast metal construction for durability\u003c\/li\u003e\n\u003cli\u003eSolid disc type with a 245 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm for consistent braking\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish to reduce uneven wear\u003c\/li\u003e\n\u003cli\u003eRust resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm for secure fitment\u003c\/li\u003e\n\u003cli\u003eHeight of 2.881 mm ensuring proper alignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10201 is a solid disc brake rotor made from high-quality metal with a full cast construction. Its 245 mm outside diameter and 10.00 mm nominal thickness provide a stable braking surface suitable for the braking systems of Volkswagen Passat and Audi A6, A6 Quattro, 100, and 100 Quattro models. The rotor features a non-directional disc finish, which helps maintain even wear patterns and consistent braking performance over time. Additionally, the rust resistant coating protects the rotor from corrosion, making it a practical choice for vehicles exposed to varying weather conditions. The bolt hole diameter of 5 mm and a height of 2.881 mm ensure proper fitment and alignment during installation.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, extending the service life of the brake components. This product line emphasizes durability and consistent braking performance through solid, full cast rotors with precise manufacturing tolerances. The SP10201 rotor is part of this line, offering a balance of protection and reliability for compatible Volkswagen and Audi vehicles.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVolkswagen Passat brake rotor replacement\u003c\/li\u003e\n\u003cli\u003eAudi A6 and A6 Quattro disc brake rotor upgrade\u003c\/li\u003e\n\u003cli\u003eAudi 100 and 100 Quattro rotor maintenance\u003c\/li\u003e\n\u003cli\u003eAddressing rotor wear and corrosion issues\u003c\/li\u003e\n\u003cli\u003eReplacing warped or uneven brake rotors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10201, ensure the rotor surface is clean and free of debris before mounting. Verify the bolt hole diameter matches the vehicle specifications to avoid fitment issues. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Proper torque specifications should be followed during installation to prevent rotor warping or uneven wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust resistant coating adds an extra layer of protection against environmental factors. While specific warranty details for part number SP10201 are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384138858677,"sku":"CNJW-SP10201","price":46.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10201_Fro_77224512-237e-45f9-a23e-23dfc404c9bd.jpg?v=1774633343"},{"product_id":"ate-sp10202-disc-brake-rotor","title":"ATE SP10202 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10202\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10202 is designed for precise fitment on select BMW models, including the 323is, 328is, 318i, 328i, 318is, 325i, and 325is. This disc brake rotor offers reliable performance with a rust-resistant coating and solid construction to maintain braking efficiency.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with BMW 323is, 328is, 318i, 328i, 318is, 325i, and 325is\u003c\/li\u003e\n\u003cli\u003ePart number SP10202 for exact replacement\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with 280 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction with non-directional disc finish\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and height of 2.728 mm\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for extended durability\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm for secure mounting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10202 is a solid disc brake rotor constructed from full cast metal, ensuring structural integrity and consistent braking performance. Its 280 mm outside diameter and 10.00 mm nominal thickness are engineered to meet the specifications required by various BMW models such as the 318i and 325is. The rotor features a non-directional disc finish, which allows for flexible installation without concern for directional orientation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, extending the service life and maintaining braking reliability under various driving conditions.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion. This product line emphasizes durability and consistent braking performance, making it suitable for vehicles that require reliable replacement parts. The SP10202 rotor is part of this line, offering a solid rotor design with a full cast metal construction and a rust-resistant finish tailored for BMW applications.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW 325i and 328i models\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency on BMW 318is and 323is vehicles\u003c\/li\u003e\n\u003cli\u003ePreventing rust-related rotor degradation in humid or wet environments\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment and secure mounting with 5 mm bolt hole diameter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with your specific BMW model before installation\u003c\/li\u003e\n\u003cli\u003eEnsure rotor surface and hub are clean and free of debris prior to mounting\u003c\/li\u003e\n\u003cli\u003eUse proper torque specifications for bolt tightening to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary during rotor installation\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to optimize braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10202 is manufactured to meet OEM standards for fit and function on compatible BMW models. The rust-resistant coating is applied to enhance durability and maintain rotor integrity over time. While specific warranty details are not provided, ATE products typically adhere to strict quality control processes to ensure reliability and performance in automotive braking systems.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384141938869,"sku":"CNJW-SP10202","price":59.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10202_Fro_45e9ae8b-0fc8-4c8a-9ee8-b4e027bd7cea.jpg?v=1774633343"},{"product_id":"ate-sp10214-disc-brake-rotor","title":"ATE SP10214 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10214\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10214 is designed specifically for Volvo models including the C70, S70, V70, and 850. This disc brake rotor offers reliable performance with a rust-resistant coating and solid construction to maintain braking efficiency over time.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Volvo C70, S70, V70, and 850 models\u003c\/li\u003e\n\u003cli\u003ePart number SP10214 for precise identification\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with a 295 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for extended durability\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction with non-directional disc finish\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 9.60 mm and bolt hole diameter of 5 mm\u003c\/li\u003e\n\u003cli\u003eHeight of 3.200 mm ensuring proper fitment and function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10214 is a solid disc brake rotor constructed from full cast metal, providing consistent braking performance. Its nominal thickness of 9.60 mm and height of 3.200 mm are engineered to meet the exact specifications required for Volvo C70, S70, V70, and 850 models. The rotor features a non-directional disc finish, which allows for uniform wear and heat dissipation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, extending the service life of the part. The bolt hole diameter measures 5 mm, ensuring secure mounting and compatibility with the vehicle's hub assembly.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion. This product line is designed to offer durability and reliable braking performance for vehicles requiring solid rotors. The coating applied to the SP10214 rotor helps maintain the rotor’s integrity in various driving conditions, making it suitable for Volvo models that demand consistent braking response.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volvo C70, S70, V70, and 850\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eEliminates noise and vibration related to damaged rotors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility by verifying part number SP10214 with vehicle make and model\u003c\/li\u003e\n\u003cli\u003eInspect hub and mounting surfaces for cleanliness before installation\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary during rotor installation\u003c\/li\u003e\n\u003cli\u003ePerform a test drive to confirm proper braking function after installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10214 is manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating is applied to enhance durability and maintain rotor performance over time. While specific warranty details are not provided, ATE products typically adhere to strict quality control processes to ensure reliability and safety in braking applications.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384142332085,"sku":"CNJW-SP10214","price":61.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10214_Fro_89810a79-5e7e-48b6-93cc-2bf478571e80.jpg?v=1774633343"},{"product_id":"ate-sp10217-disc-brake-rotor","title":"ATE SP10217 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10217\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10217 is engineered for reliable braking performance on select Mercedes-Benz models. Designed as a solid disc brake rotor with rust-resistant coating, it offers durability and consistent stopping power for vehicles like the Mercedes-Benz SLK300 and CLK350.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm ensuring proper rotor life and performance\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 290.00 mm compatible with specified Mercedes-Benz models\u003c\/li\u003e\n\u003cli\u003eHeight: 2.476 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eType: Solid rotor for consistent braking response\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to combat rust and corrosion, which is critical for maintaining braking efficiency over time. This product line includes solid, full cast rotors like the SP10217, designed to meet the specifications required by Mercedes-Benz vehicles such as the E320 and C350. The coating enhances rotor longevity without compromising braking performance.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP10217 disc brake rotor is a solid, full cast metal rotor with a nominal thickness of 10.00 mm and an outside diameter of 290 mm. Its non-directional disc finish allows for flexible installation on compatible Mercedes-Benz models including the SLK280, CLK430, and C36 AMG. The rotor features a 5 mm bolt hole diameter ensuring a secure fit, while the rust-resistant coating helps prevent corrosion caused by environmental exposure. With a height of 2.476 mm, this rotor maintains proper alignment and clearance within the braking system, contributing to consistent braking performance and safety.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement rotor for Mercedes-Benz SLK300, SLK350, and SLK280\u003c\/li\u003e\n\u003cli\u003eSuitable for Mercedes-Benz CLK350, CLK320, and CLK430 models\u003c\/li\u003e\n\u003cli\u003eCompatible with Mercedes-Benz C280, C230, C240, C320, C350, and C36 AMG\u003c\/li\u003e\n\u003cli\u003eFits Mercedes-Benz E300, E320, E420, and E430 vehicles\u003c\/li\u003e\n\u003cli\u003eIdeal for addressing rotor wear, vibration, and corrosion issues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure rotor thickness meets or exceeds minimum manufacturer specifications before installation\u003c\/li\u003e\n\u003cli\u003eClean mounting surface to prevent uneven rotor seating\u003c\/li\u003e\n\u003cli\u003eUse proper torque settings on bolts with 5 mm diameter holes for secure fitment\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary to avoid uneven rotor wear\u003c\/li\u003e\n\u003cli\u003eFollow vehicle-specific service manual for brake system bleeding and testing after installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10217 is manufactured to meet OEM standards for fit, form, and function on Mercedes-Benz vehicles. The rust-resistant coating is applied to extend rotor life under typical driving conditions. While specific warranty details are not provided, ATE products generally adhere to strict quality control processes to ensure reliability and safety in braking applications.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384142430389,"sku":"CNJW-SP10217","price":53.73,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10217_Fro_2688c979-57a3-4699-a010-c9448669e57e.jpg?v=1774633344"},{"product_id":"ate-sp10224-disc-brake-rotor","title":"ATE SP10224 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10224\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10224 is designed for reliable braking performance on Volkswagen Passat and Audi A4 Quattro models. This disc brake rotor features a rust-resistant coating and solid construction to ensure durability and consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal with rust-resistant coating\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 245.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast, solid rotor type\u003c\/li\u003e\n\u003cli\u003eHeight: 2.255 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings to reduce corrosion and extend service life. The SP10224 rotor benefits from this coating, which helps maintain rotor integrity and performance over time, especially in environments prone to moisture and road salt. This line is tailored for vehicles requiring solid, full cast rotors with consistent thickness and fitment precision.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Fitment\u003c\/h2\u003e\u003cp\u003eThe SP10224 disc brake rotor is a solid, full cast metal rotor with a nominal thickness of 10.00 mm and an outside diameter of 245.00 mm. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. The 5 mm bolt hole diameter ensures compatibility with the mounting hardware on Volkswagen Passat and Audi A4 Quattro models. The rust-resistant coating protects the rotor surface from corrosion, helping maintain braking efficiency and rotor lifespan.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volkswagen Passat and Audi A4 Quattro\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor thickness\u003c\/li\u003e\n\u003cli\u003eReducing corrosion-related rotor damage in humid or salted road conditions\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency with a solid, full cast rotor design\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with exact bolt hole diameter and rotor dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify rotor dimensions and bolt hole diameter match vehicle specifications before installation\u003c\/li\u003e\n\u003cli\u003eEnsure the rotor surface is clean and free of debris prior to mounting\u003c\/li\u003e\n\u003cli\u003eUse proper torque settings on wheel bolts to avoid rotor distortion\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary to optimize rotor performance\u003c\/li\u003e\n\u003cli\u003eNon-directional finish allows installation on either side without performance impact\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10224 is manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating enhances durability under typical driving conditions. While specific warranty details are not provided, ATE products generally adhere to strict quality control processes to ensure reliable braking performance on Volkswagen Passat and Audi A4 Quattro vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384143511733,"sku":"CNJW-SP10224","price":45.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10224_Fro_daae0468-96ce-4e54-9fe8-c91ee44be8d5.jpg?v=1774633344"},{"product_id":"ate-sp10226-disc-brake-rotor","title":"ATE SP10226 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10226\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10226 is designed specifically for Saab vehicles including the 9-3, 9-5, and 900 models. This disc brake rotor offers reliable performance with a rust-resistant coating and solid construction to meet the demands of everyday driving.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal with rust-resistant coating\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 286.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast, solid rotor type\u003c\/li\u003e\n\u003cli\u003eHeight: 3.102 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10226 is a solid disc brake rotor constructed from full cast metal, providing consistent braking performance and durability. Its nominal thickness of 10.00 mm and outside diameter of 286.00 mm are engineered to match the specifications required for Saab 9-3, 9-5, and 900 models. The rotor features a non-directional disc finish, which allows for flexible installation without concern for directional orientation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, extending the service life and maintaining braking efficiency under various environmental conditions.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with enhanced corrosion resistance through specialized coatings. This line is designed to offer reliable braking components that maintain structural integrity and performance over time. The SP10226 rotor is part of this line, combining full cast solid construction with a protective coating to meet the needs of Saab vehicles requiring dependable disc brake rotors.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Saab 9-3, 9-5, and 900 models\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eSuitable for vehicles experiencing noise or vibration during braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Saab 9-3, 9-5, and 900 models before installation\u003c\/li\u003e\n\u003cli\u003eCheck rotor thickness and bolt hole diameter (5 mm) for proper fit\u003c\/li\u003e\n\u003cli\u003eUse recommended torque specifications for mounting bolts\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if worn to ensure optimal rotor performance\u003c\/li\u003e\n\u003cli\u003eClean rotor surface before installation to remove any protective oils or residues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10226 is manufactured to meet OEM standards for fit and function. The rust-resistant coating is applied to enhance durability and corrosion protection. While specific warranty details are not provided, ATE products typically adhere to strict quality control processes to ensure reliability and safety in braking applications.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384143577269,"sku":"CNJW-SP10226","price":57.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10226_Fro_72f49a47-5fe3-442f-b251-edb2425bda84.jpg?v=1774633344"},{"product_id":"ate-sp10229-disc-brake-rotor","title":"ATE SP10229 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10229\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10229 is designed specifically for Volvo S40 and V40 models, providing reliable braking performance. This disc brake rotor features a rust-resistant coating and solid construction to ensure durability and consistent operation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Volvo S40 and V40 models\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with 260 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction for strength and stability\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for uniform wear\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and height of 2.295 inches\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 4 mm for secure fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10229 is a solid disc brake rotor engineered from full cast metal, ensuring structural integrity and consistent braking performance. Its 260 mm outside diameter and 10.00 mm nominal thickness are optimized for the braking systems of Volvo S40 and V40 vehicles. The rotor features a non-directional disc finish, which promotes even pad wear and smooth braking response. Additionally, the rust-resistant coating protects the rotor surface from corrosion, helping to maintain braking efficiency over time. The bolt hole diameter of 4 mm ensures a precise and secure installation on compatible Volvo models.\u003c\/p\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings that resist rust and corrosion, extending the service life of the brake components. This line is designed to meet the demands of everyday driving conditions while maintaining consistent braking performance.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volvo S40 and V40\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency and pedal feel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Volvo S40 or V40 before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if worn to avoid uneven rotor wear\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to ensure proper rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications for secure fitment\u003c\/li\u003e\n\u003cli\u003ePerform a brake system test after installation to verify performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust-resistant coating adds an extra layer of protection against corrosion. Please refer to the product packaging or manufacturer documentation for specific warranty details related to the ATE Coated Single Pack Rotor SP10229.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384143741109,"sku":"CNJW-SP10229","price":45.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10229_Fro_204a0f52-b4fb-483d-9c93-34b0bdc61766.jpg?v=1774633345"},{"product_id":"ate-sp10258-disc-brake-rotor","title":"ATE SP10258 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10258\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10258 is engineered for Audi A6 Quattro models, providing reliable braking performance with a durable metal construction. Designed as a solid disc brake rotor, it features a rust-resistant coating to extend service life under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm ensuring consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support uniform wear\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to prevent corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 245.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.484 inches for proper clearance\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10258 is specifically designed for the Audi A6 Quattro, ensuring compatibility and optimal braking performance. This rotor is constructed from high-quality metal with a full cast design, providing the necessary strength and rigidity for consistent braking. The solid rotor type offers a reliable braking surface without the complexity of vented designs, suitable for standard driving conditions. Its non-directional disc finish promotes even pad wear and braking efficiency. Additionally, the rust-resistant coating helps protect the rotor from corrosion, extending its operational lifespan and maintaining performance over time.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on delivering rotors with protective coatings to resist rust and corrosion, which is critical for maintaining braking performance and rotor longevity. This product line emphasizes durability and fitment precision, making it a practical choice for vehicles like the Audi A6 Quattro that require reliable replacement parts meeting OEM standards.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi A6 Quattro\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing corrosion-related rotor degradation\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency with a solid, full cast rotor\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with exact bolt hole diameter and rotor dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify rotor dimensions and bolt hole diameter match your Audi A6 Quattro specifications\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if worn to ensure optimal rotor performance\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces before installation to prevent uneven rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003ePerform a brake system test after installation to confirm proper operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the Coated Single Pack Rotor SP10258, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to enhance longevity under typical driving conditions. Warranty coverage details should be confirmed with the point of purchase or manufacturer documentation.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384144265397,"sku":"CNJW-SP10258","price":45.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10258_Fro_d4c88afb-286d-4ac7-8ded-33d401cf98cf.jpg?v=1774633345"},{"product_id":"ate-sp10259-disc-brake-rotor","title":"ATE SP10259 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10259\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10259 is engineered for reliable braking performance on Audi A6 Quattro models. Designed as a solid disc brake rotor, it features a rust-resistant coating to enhance durability and maintain consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm for optimal rotor life\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to prevent corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 255.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.484 mm for proper clearance and fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings that resist rust and corrosion. This coating extends the rotor's service life and helps maintain braking efficiency over time. The SP10259 rotor is part of this line, offering a solid, full cast design suitable for Audi A6 Quattro vehicles requiring dependable disc brake components.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Features\u003c\/h2\u003e\u003cp\u003eThis disc brake rotor is constructed from metal with a full cast solid design, providing consistent braking performance and structural integrity. The nominal thickness of 10.00 mm ensures the rotor meets durability standards while the 255.00 mm outside diameter aligns with Audi A6 Quattro factory specifications. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating protects the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi A6 Quattro models requiring a 255 mm solid disc brake rotor\u003c\/li\u003e\n\u003cli\u003eIdeal replacement for worn or damaged rotors to restore braking performance\u003c\/li\u003e\n\u003cli\u003eSuitable for addressing issues such as brake noise, vibration, and uneven wear\u003c\/li\u003e\n\u003cli\u003eHelps maintain safe stopping distances and brake system reliability\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the rotor matches the OEM specifications for your Audi A6 Quattro\u003c\/li\u003e\n\u003cli\u003eCheck bolt hole diameter (5 mm) and rotor height (2.484 mm) for proper fit\u003c\/li\u003e\n\u003cli\u003eClean the rotor surface before installation to remove any protective oils\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid warping\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware during rotor replacement for optimal performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10259 is manufactured to meet strict quality standards for durability and performance. The rust-resistant coating adds an extra layer of protection against corrosion, contributing to longer rotor life. Warranty details should be confirmed with the original equipment manufacturer or authorized distributor to ensure coverage specifics.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384144724149,"sku":"CNJW-SP10259","price":47.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10259_Fro.jpg?v=1774633345"},{"product_id":"ate-sp10260-disc-brake-rotor","title":"ATE SP10260 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10260\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10260 is designed specifically for Audi Allroad Quattro and A6 Quattro models. This disc brake rotor offers reliable performance with a rust-resistant coating and solid construction to maintain braking efficiency under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi Allroad Quattro and A6 Quattro\u003c\/li\u003e\n\u003cli\u003ePart number: SP10260\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast metal construction\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and outside diameter of 255.00 mm\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for consistent braking\u003c\/li\u003e\n\u003cli\u003eRust resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 2.405 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing durable, corrosion-resistant rotors designed for direct replacement. The rust resistant coating on the SP10260 helps protect the rotor surface from environmental damage, reducing the risk of rust and extending service intervals. This product line emphasizes solid rotor construction, ensuring consistent braking performance for vehicles like the Audi Allroad Quattro and A6 Quattro.\u003c\/p\u003e\u003ch2\u003eTechnical Specifications and Features\u003c\/h2\u003e\u003cp\u003eThe SP10260 rotor is a solid disc type made from full cast metal, offering a nominal thickness of 10.00 mm and an outside diameter of 255.00 mm. Its non-directional disc finish allows for uniform wear and braking response regardless of rotor orientation. The rotor includes a bolt hole diameter of 5 mm and a height of 2.405 mm, designed to meet the exact fitment requirements of the specified Audi models. The rust resistant coating enhances durability by protecting the rotor surface from corrosion, which is especially beneficial in wet or humid environments.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi Allroad Quattro and A6 Quattro\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper brake pad contact and stopping power\u003c\/li\u003e\n\u003cli\u003eImproves overall brake system reliability and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10260, ensure the rotor surface is clean and free of any contaminants before mounting. Verify the bolt hole diameter and rotor height match the vehicle specifications. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Proper torque specifications should be followed when securing the rotor to avoid warping or uneven wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust resistant coating on the SP10260 rotor provides additional protection against corrosion. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384153997493,"sku":"CNJW-SP10260","price":46.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10260_Fro_6f6811d5-c61b-4859-bdb2-5ab4d1b5ff11.jpg?v=1774633345"},{"product_id":"ate-sp10261-disc-brake-rotor","title":"ATE SP10261 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10261\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10261 is engineered for reliable braking performance on Audi vehicles, including the A4, A4 Quattro, and Coupe Quattro models. Designed as a solid disc brake rotor, it features a rust-resistant coating to enhance durability and maintain consistent braking efficiency.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi A4, A4 Quattro, and Coupe Quattro\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast construction\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and outside diameter of 245.00 mm\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for uniform wear\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for extended service life\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 2.401 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10261 is constructed from high-quality metal with a full cast design, ensuring structural integrity and consistent heat dissipation during braking. Its solid rotor type provides a stable braking surface, suitable for the specified Audi models. The non-directional disc finish allows for even pad contact and wear, reducing the risk of uneven braking performance. The rotor measures 245.00 mm in outside diameter and maintains a nominal thickness of 10.00 mm, meeting the precise requirements for the Audi A4, A4 Quattro, and Coupe Quattro. Additionally, the rust-resistant coating protects the rotor from corrosion, which is critical for maintaining braking efficiency over time.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, extending the rotor's lifespan and maintaining braking performance. This product line emphasizes durability and consistent braking characteristics, making it suitable for vehicles like the Audi A4 series where reliable stopping power is essential. The SP10261 part number is part of this line, offering a balance of quality materials and protective features.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi A4, A4 Quattro, and Coupe Quattro\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation and noise\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for optimal braking performance\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency and safety under normal driving conditions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10261, ensure the rotor surface is clean and free of debris before mounting. Verify the bolt hole diameter matches the vehicle specifications (5 mm) and torque bolts to manufacturer-recommended settings. It is advisable to replace brake pads simultaneously to ensure even wear and optimal braking performance. Check rotor thickness and height (2.401 inches) to confirm compatibility with your Audi model.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust-resistant coating adds an extra layer of protection against environmental factors. While specific warranty details for part number SP10261 should be confirmed with the supplier, ATE products typically come with a limited warranty covering manufacturing defects.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384154259637,"sku":"CNJW-SP10261","price":43.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10261_Fro_21f94ae1-7803-48b7-8b23-4aa032ffb4aa.jpg?v=1774633346"},{"product_id":"ate-sp10273-disc-brake-rotor","title":"ATE SP10273 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10273 for BMW Z3\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10273 is designed specifically for the BMW Z3, providing reliable braking performance with durable construction. This disc brake rotor features a rust-resistant coating and solid design to meet the demands of everyday driving.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm for consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm to ensure proper fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for stability\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 272.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 3.629 inches for precise fitment\u003c\/li\u003e\n\u003cli\u003eType: Solid disc brake rotor designed for BMW Z3\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion. This product line is engineered to maintain braking efficiency and rotor integrity over time, especially in environments prone to moisture and road salt. The SP10273 rotor benefits from this coating technology, ensuring longer service intervals and consistent performance for the BMW Z3.\u003c\/p\u003e\u003ch2\u003eTechnical Description of the SP10273 Disc Brake Rotor\u003c\/h2\u003e\u003cp\u003eThe SP10273 rotor is a full cast, solid disc brake rotor constructed from metal to deliver reliable braking force. Its nominal thickness of 10.00 mm ensures a stable braking surface, while the 272 mm outside diameter and 3.629 inch height are designed to match the BMW Z3’s original equipment specifications. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor from corrosion, which can degrade braking performance over time.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW Z3 models\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing corrosion-related rotor damage in humid or salty environments\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency with a solid, full cast rotor design\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with exact OEM bolt hole diameter and dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10273 on a BMW Z3, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side without concern for rotation direction. Verify that the bolt hole diameter matches the vehicle’s hub to avoid fitment issues. It is recommended to replace brake pads simultaneously to maintain optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP10273, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to extend rotor life and maintain braking efficiency. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384155209909,"sku":"CNJW-SP10273","price":64.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10273_Fro.jpg?v=1774633346"},{"product_id":"ate-sp10274-disc-brake-rotor","title":"ATE SP10274 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10274\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10274 is engineered for reliable braking performance on Saab 9-5 models. Designed as a solid disc brake rotor with rust-resistant coating, it offers durability and consistent stopping power tailored to your vehicle's specifications.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Saab 9-5 vehicles\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor construction\u003c\/li\u003e\n\u003cli\u003eFull cast metal material for strength\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and outside diameter of 286.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 3.078 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10274 is a solid rotor made from full cast metal, ensuring structural integrity and consistent braking performance. Its nominal thickness of 10.00 mm and outside diameter of 286.00 mm are designed to meet the exact requirements of Saab 9-5 disc brake systems. The rotor features a non-directional disc finish, allowing for flexible installation without concern for directional wear patterns. Additionally, the rotor is coated with a rust-resistant layer to protect against corrosion, which helps maintain braking efficiency over time. The bolt hole diameter measures 5 mm, and the rotor height is 3.078 inches, matching factory specifications for proper fitment and function.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, extending the service life of the brake components. This product line emphasizes durability and reliable performance, making it suitable for vehicles like the Saab 9-5 that require precise fitment and consistent braking response. The SP10274 part number is part of this line, combining full cast construction with a protective coating to meet OEM standards.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Saab 9-5 models\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eResolving reduced braking efficiency due to rotor corrosion\u003c\/li\u003e\n\u003cli\u003eEliminating vibration or pulsation during braking\u003c\/li\u003e\n\u003cli\u003eUpgrading to a rust-resistant rotor for longer service intervals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10274, ensure the rotor surface and hub are clean and free of debris to prevent uneven wear. Use proper torque specifications for the 5 mm bolt holes to secure the rotor firmly. The non-directional finish allows installation on either side without concern for directional rotation. It is recommended to inspect brake pads and hardware during installation to maintain optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring compatibility and performance for Saab 9-5 vehicles. The rust-resistant coating provides added protection against environmental factors. Warranty details should be confirmed with the supplier or manufacturer, as coverage may vary.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384156848309,"sku":"CNJW-SP10274","price":56.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10274_Fro_cbdf7fa8-55a8-413d-b60f-c434a2472541.jpg?v=1774633347"},{"product_id":"ate-sp10278-disc-brake-rotor","title":"ATE SP10278 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10278\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10278 is engineered for reliable braking performance on select Mercedes-Benz models. Designed as a solid disc brake rotor, it offers durability and corrosion resistance tailored for vehicles like the Mercedes-Benz E250, E320, and E500.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm ensuring consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to allow flexible installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 300.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 3.062 inches for proper caliper clearance\u003c\/li\u003e\n\u003cli\u003eType: Solid rotor optimized for standard braking applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, enhancing longevity and maintaining braking efficiency. This product line includes solid rotors like the SP10278, which are designed to meet the exacting standards required by Mercedes-Benz vehicles, ensuring compatibility and reliable performance.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP10278 disc brake rotor from ATE is a full cast, solid rotor with a nominal thickness of 10.00 mm and an outside diameter of 300.00 mm. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. The rotor features a rust-resistant coating that helps prevent corrosion, which is critical for maintaining braking performance over time. With a bolt hole diameter of 5 mm and a height of 3.062 inches, this rotor is engineered to fit Mercedes-Benz E250, E320, and E500 models precisely, ensuring proper alignment and function within the braking system.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz E250, E320, and E500\u003c\/li\u003e\n\u003cli\u003eRestores braking efficiency and pedal feel\u003c\/li\u003e\n\u003cli\u003eAddresses rotor corrosion and surface rust problems\u003c\/li\u003e\n\u003cli\u003eEliminates brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents brake judder and vibration during stopping\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10278, ensure the rotor surface is clean and free of any protective oils before mounting. The non-directional finish allows installation on either side, simplifying the process. Verify bolt hole alignment with the vehicle hub and torque bolts to manufacturer specifications. It is recommended to replace brake pads simultaneously to optimize braking performance and rotor lifespan.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to extend service life under typical driving conditions. While specific warranty details for part number SP10278 should be confirmed with the supplier, ATE products generally come with a limited warranty covering manufacturing defects.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384166547637,"sku":"CNJW-SP10278","price":60.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10278_Fro_a9b8ceea-dd2c-4470-b90b-2b40785004ee.jpg?v=1774633347"},{"product_id":"ate-sp10287-disc-brake-rotor","title":"ATE SP10287 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10287 for BMW Z4\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10287 is designed specifically for BMW Z4 models, providing reliable braking performance with durable construction. This disc brake rotor features a rust-resistant coating and solid design to meet the demands of everyday driving.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm for consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm to ensure proper fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for stability\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 280.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 3.318 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, enhancing longevity and maintaining braking efficiency. This product line is engineered to meet the specific requirements of vehicles like the BMW Z4, ensuring compatibility and reliable performance under various driving conditions.\u003c\/p\u003e\u003ch2\u003eTechnical Description of the SP10287 Disc Brake Rotor\u003c\/h2\u003e\u003cp\u003eThe SP10287 rotor is a full cast, solid disc brake rotor constructed from metal, offering a nominal thickness of 10.00 mm and an outside diameter of 280.00 mm. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. The 5 mm bolt hole diameter ensures secure mounting on the BMW Z4 hub assembly. The rust-resistant coating applied to the rotor surface helps prevent corrosion, which is critical for maintaining braking performance and rotor integrity over time. With a height of 3.318 mm, this rotor fits precisely within the brake caliper assembly, providing consistent contact with brake pads.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW Z4 models\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eSuitable for solid rotor applications requiring OEM specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10287 on a BMW Z4, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side without affecting performance. Torque the bolts to manufacturer specifications using the 5 mm bolt holes to secure the rotor properly. It is recommended to inspect brake pads and hardware during installation to ensure optimal braking system function.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring durability and consistent braking performance. The rust-resistant coating extends the rotor's service life by protecting against corrosion. While specific warranty details for part number SP10287 are not provided, ATE products typically come with manufacturer-backed quality assurance to support reliability and fitment for BMW Z4 vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384170971317,"sku":"CNJW-SP10287","price":63.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10287_Fro_0aaaed55-e9c8-4370-9fbf-68b81c7f2657.jpg?v=1774633347"},{"product_id":"ate-sp10328-disc-brake-rotor","title":"ATE SP10328 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10328\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10328 is designed specifically for Mercedes-Benz C250 and C300 models. This solid disc brake rotor features a rust-resistant coating and a full cast metal construction to ensure durability and reliable braking performance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal with rust-resistant coating\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 10.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 300.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc\u003c\/li\u003e\n\u003cli\u003eHeight: 2.547 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to reduce corrosion and extend service life. This product line includes solid rotors constructed from full cast metal, designed to maintain consistent braking performance under normal driving conditions. The rust-resistant coating on the SP10328 rotor helps protect the braking surface and rotor body from environmental factors, making it suitable for Mercedes-Benz C250 and C300 vehicles.\u003c\/p\u003e\u003ch2\u003eTechnical Description of the SP10328 Disc Brake Rotor\u003c\/h2\u003e\u003cp\u003eThe SP10328 rotor is a solid disc brake rotor with a nominal thickness of 10.00 mm and an outside diameter of 300.00 mm. Its full cast metal construction provides structural integrity and heat dissipation during braking. The non-directional disc finish allows for flexible installation without concern for rotor orientation. The rotor’s bolt hole diameter measures 5 mm, ensuring compatibility with the specified Mercedes-Benz models. Additionally, the rust-resistant coating helps prevent corrosion, which can affect braking efficiency and rotor longevity.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz C250 and C300\u003c\/li\u003e\n\u003cli\u003eAddresses rotor corrosion and rust buildup\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency and reduces noise\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking\u003c\/li\u003e\n\u003cli\u003eSuitable for vehicles experiencing brake pulsation or vibration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Mercedes-Benz C250 or C300 before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear during rotor replacement\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to prevent uneven rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque lug nuts to manufacturer specifications\u003c\/li\u003e\n\u003cli\u003ePerform a brake system test after installation to verify proper function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10328 is manufactured to meet OEM standards for fit and function. The rust-resistant coating enhances durability against environmental exposure. While specific warranty details are not provided, ATE products typically adhere to strict quality control processes to ensure reliable performance on Mercedes-Benz C250 and C300 vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384171102389,"sku":"CNJW-SP10328","price":64.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10328_Fro_33b8bc21-d45a-4bc9-97e4-b936c1ca9086.jpg?v=1774633348"},{"product_id":"ate-sp10351-disc-brake-rotor","title":"ATE SP10351 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP10351\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP10351 is engineered for Mercedes-Benz SL500 models, providing reliable braking performance with a durable metal construction. Designed as a solid disc brake rotor, it features a rust-resistant coating to extend service life under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Mercedes-Benz SL500\u003c\/li\u003e\n\u003cli\u003ePart number SP10351 for precise identification\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast construction\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for enhanced durability\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for consistent braking\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 10.00 mm and outside diameter of 300 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 2.543 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThis ATE Coated Single Pack Rotor SP10351 is constructed from high-quality metal with a full cast design, ensuring structural integrity and consistent performance. The rotor is solid rather than vented, which suits specific braking system requirements of the Mercedes-Benz SL500. Its nominal thickness of 10.00 mm and outside diameter of 300 mm align with OEM specifications for this vehicle. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rotor includes a rust-resistant coating that helps prevent corrosion, maintaining braking efficiency over time. The bolt hole diameter measures 5 mm, and the rotor height is 2.543 mm, matching the precise fitment needs of the SL500.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, extending the rotor's lifespan and maintaining braking performance. This product line is designed to meet the demands of specific vehicle models, such as the Mercedes-Benz SL500, ensuring compatibility and reliable operation. The coating also helps reduce maintenance needs and preserves the rotor's appearance over time.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz SL500\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eResolving reduced braking efficiency due to rotor corrosion\u003c\/li\u003e\n\u003cli\u003eEliminating vibration or pulsation during braking\u003c\/li\u003e\n\u003cli\u003eUpgrading to a rust-resistant rotor for longer service intervals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP10351 on a Mercedes-Benz SL500, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side without concern for rotation direction. Verify bolt hole alignment with the vehicle hub using the 5 mm bolt hole diameter specification. It is recommended to replace brake pads simultaneously to ensure optimal braking performance. Proper torque specifications should be followed to avoid rotor warping.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP10351, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to enhance longevity under typical driving conditions. While specific warranty details are not provided here, ATE products generally come with manufacturer-backed warranties covering defects in materials and workmanship. Always consult the product documentation or manufacturer for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384172708021,"sku":"CNJW-SP10351","price":47.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP10351_Fro_0f0ad9c0-f6d3-4c86-bf08-a30a3203f06c.jpg?v=1774633348"},{"product_id":"ate-sp11153-disc-brake-rotor","title":"ATE SP11153 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP11153\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP11153 is engineered for reliable braking performance on select Mercedes-Benz models. Designed as a solid disc brake rotor, it offers durability and corrosion resistance tailored for vehicles like the Mercedes-Benz CL500, S350, S430, and S500.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-quality metal construction\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 11.00 mm for consistent braking\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, for extended service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 300.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.657 inches\u003c\/li\u003e\n\u003cli\u003eType: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings to reduce rust and corrosion. This coating enhances the rotor's longevity and maintains braking efficiency over time. The SP11153 rotor benefits from this coating, making it suitable for Mercedes-Benz vehicles that require reliable, maintenance-friendly brake components.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP11153 disc brake rotor is constructed from metal with a full cast design, ensuring structural integrity and consistent performance under braking stress. Its nominal thickness of 11.00 mm supports effective heat dissipation and wear resistance. The rotor features a non-directional disc finish, allowing for flexible installation without concern for directional orientation. With a bolt hole diameter of 5 mm and an outside diameter of 300.00 mm, this rotor is engineered to meet the exact specifications required by Mercedes-Benz CL500, S350, S430, and S500 models. The rust-resistant coating further protects the rotor surface from corrosion, which is critical for maintaining braking reliability in various driving conditions.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz CL500, S350, S430, and S500\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing rust buildup that can impair braking performance\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency and pedal feel\u003c\/li\u003e\n\u003cli\u003eEnsuring proper rotor thickness for safe braking operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP11153, ensure the rotor surface is clean and free of debris before mounting. Verify the bolt hole diameter matches the vehicle hub to avoid fitment issues. Since the rotor has a non-directional finish, it can be installed on either side without affecting performance. It is recommended to replace brake pads simultaneously to optimize braking efficiency and rotor lifespan.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP11153, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to extend the rotor's service life. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384173232309,"sku":"CNJW-SP11153","price":61.92,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP11153_Fro_7ccb5a93-0dce-4727-9d57-8b93204747db.jpg?v=1774633349"},{"product_id":"ate-sp11158-disc-brake-rotor","title":"ATE SP11158 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP11158\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP11158 is designed for reliable braking performance on select Volvo models. Engineered with a rust-resistant coating and solid construction, this disc brake rotor ensures durability and consistent stopping power for your Volvo C30, C70, S40, and V50 vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Volvo C30, C70, S40, and V50 models\u003c\/li\u003e\n\u003cli\u003ePart number SP11158 for precise identification\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast metal construction\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 11.00 mm and outside diameter of 280 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and rotor height of 2.287 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP11158 is a solid disc brake rotor made from full cast metal, providing a robust and stable braking surface. Its nominal thickness of 11.00 mm and outside diameter of 280 mm are designed to meet the exact specifications required for Volvo C30, C70, S40, and V50 models. The rotor features a non-directional disc finish, allowing for flexible installation without concern for directional wear patterns. Additionally, the rotor includes a rust-resistant coating that helps protect against corrosion, extending the service life of the part. The bolt hole diameter measures 5 mm, and the rotor height is 2.287 inches, ensuring proper fitment and compatibility with the vehicle's braking system.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing high-quality disc brake rotors with protective coatings to resist rust and corrosion. This product line emphasizes durability and consistent braking performance, making it suitable for vehicles that require reliable stopping power under various driving conditions. The SP11158 rotor is part of this line, offering a solid rotor design with a full cast metal construction and a rust-resistant finish tailored for Volvo models.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volvo C30, C70, S40, and V50\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation in humid or wet environments\u003c\/li\u003e\n\u003cli\u003eRestores proper braking performance and pedal feel\u003c\/li\u003e\n\u003cli\u003eEliminates vibration issues linked to rotor thickness variation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility by verifying part number SP11158 with your Volvo model\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware during rotor replacement for optimal performance\u003c\/li\u003e\n\u003cli\u003eFollow manufacturer torque specifications for bolt installation\u003c\/li\u003e\n\u003cli\u003eClean rotor mounting surface to prevent misalignment or runout\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to ensure proper rotor and pad contact\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust-resistant coating on the SP11158 rotor provides added protection against corrosion. While specific warranty details may vary, ATE products typically come with a limited warranty covering defects in materials and workmanship. Consult product documentation or your supplier for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384176410805,"sku":"CNJW-SP11158","price":53.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP11158_Fro_591ced1e-7ce3-4ba3-8787-d305e1c3ff7d.jpg?v=1774633349"},{"product_id":"ate-sp12106-disc-brake-rotor","title":"ATE SP12106 Disc Brake Rotor - Front","description":"\u003ch2\u003eReliable Disc Brake Rotor for Volkswagen and Audi Models\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12106 offers a durable and precise braking solution for select Volkswagen and Audi vehicles. Designed with a rust-resistant coating and solid construction, this rotor ensures consistent performance and longevity.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFull cast metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eSolid disc type with a nominal thickness of 12.00 mm\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eRust resistant coating to protect against corrosion\u003c\/li\u003e\n\u003cli\u003eOutside diameter of 239.00 mm and height of 2.377 inches\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 4 mm for secure fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line is engineered to provide reliable braking components with enhanced corrosion resistance. This product line focuses on delivering rotors with protective coatings that extend service life, making them suitable for vehicles exposed to varying road conditions. The SP12106 rotor exemplifies this approach with its rust resistant coating and solid cast design.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP12106 disc brake rotor is constructed from high-quality metal with a full cast design, ensuring structural integrity and consistent braking performance. Its solid rotor type and 12.00 mm nominal thickness provide a stable braking surface, while the non-directional disc finish allows for flexible installation without concern for directional wear patterns. The rust resistant coating helps prevent corrosion, which is especially beneficial for Volkswagen and Audi models such as the Golf, Jetta, Fox, Quantum, 4000, Coupe, and Rabbit Pickup. With an outside diameter of 239.00 mm and a height of 2.377 inches, this rotor fits securely with a bolt hole diameter of 4 mm, ensuring proper alignment and fitment.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volkswagen Golf and Jetta models\u003c\/li\u003e\n\u003cli\u003eRestores braking efficiency on Audi Coupe and 4000 vehicles\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation in Fox and Rabbit Pickup models\u003c\/li\u003e\n\u003cli\u003eEliminates brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproves overall brake system reliability and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with specific Volkswagen and Audi models before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear during rotor replacement\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to prevent uneven rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications using the 4 mm bolt hole diameter\u003c\/li\u003e\n\u003cli\u003ePerform a brake system test after installation to verify proper function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12106 is manufactured to meet strict quality standards for durability and performance. The rust resistant coating adds an extra layer of protection against environmental factors. While specific warranty details are not provided, ATE products typically adhere to industry standards for reliability and are backed by quality control processes to ensure customer satisfaction.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384186110133,"sku":"CNJW-SP12106","price":44.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12106_Fro_1ee34690-026a-49dc-aaa8-99ea138a7cdb.jpg?v=1774633350"},{"product_id":"ate-sp12148-disc-brake-rotor","title":"ATE SP12148 Disc Brake Rotor - Rear","description":"\u003ch2\u003eReliable Disc Brake Rotor for Audi A4 and A4 Quattro\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12148 is designed specifically for Audi A4 and A4 Quattro models, providing consistent braking performance. This solid disc brake rotor features a rust-resistant coating to enhance durability and maintain optimal function over time.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.00 mm for reliable wear resistance\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to prevent corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 255.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.401 inches for proper clearance and fit\u003c\/li\u003e\n\u003cli\u003eType: Solid rotor for consistent braking response\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing high-quality, corrosion-resistant rotors that meet or exceed OEM standards. The SP12148 model benefits from a full cast construction and a protective coating that helps extend rotor life, making it suitable for Audi A4 and A4 Quattro vehicles requiring dependable braking components.\u003c\/p\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThis disc brake rotor is engineered with a solid, full cast metal design, ensuring structural integrity and consistent braking performance. The 12.00 mm nominal thickness supports long service life, while the 255 mm outside diameter and 5 mm bolt hole diameter guarantee compatibility with specified Audi models. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi A4 and A4 Quattro\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency and pedal feel\u003c\/li\u003e\n\u003cli\u003ePreventing rust and corrosion-related rotor damage\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with OEM bolt hole and diameter specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12148, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side, simplifying the process. Verify bolt hole alignment with the vehicle hub and torque bolts to manufacturer specifications. It is recommended to replace brake pads simultaneously to maintain optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust-resistant coating adds an extra layer of protection against environmental factors. Please refer to ATE's official warranty policy for coverage details related to the SP12148 rotor.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384196694197,"sku":"CNJW-SP12148","price":48.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12148_Fro.jpg?v=1774633350"},{"product_id":"ate-sp12149-disc-brake-rotor","title":"ATE SP12149 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12149\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12149 is engineered for reliable braking performance on Mercedes-Benz E320 models. Designed as a solid disc brake rotor, it features a rust-resistant coating to enhance durability and maintain consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Mercedes-Benz E320 vehicles\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast construction\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 12.00 mm and outside diameter of 290.00 mm\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to prevent corrosion\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and rotor height of 2.578 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12149 is constructed from high-quality metal with a full cast design, ensuring structural integrity and consistent performance. Its solid rotor type provides a stable braking surface, suitable for the Mercedes-Benz E320. The rotor measures 290.00 mm in outside diameter and has a nominal thickness of 12.00 mm, meeting precise OEM specifications. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating extends the rotor's lifespan by protecting against corrosion, which is critical for maintaining braking efficiency over time. The bolt hole diameter of 5 mm and a height of 2.578 inches ensure proper fitment and compatibility with the vehicle's braking system.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, enhancing durability in various driving conditions. This product line is designed to meet the demands of specific vehicle models, such as the Mercedes-Benz E320, by offering rotors that maintain performance and structural integrity over time. The SP12149 part number represents a solid rotor option within this line, combining full cast construction with a protective coating for reliable braking.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz E320\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for consistent brake pad contact\u003c\/li\u003e\n\u003cli\u003eImproves overall braking performance and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12149, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows for installation on either side without concern for directional rotation. Verify bolt hole alignment with the vehicle hub using the 5 mm bolt hole diameter specification. It is recommended to replace brake pads simultaneously to ensure optimal braking performance. Proper torque specifications should be followed during installation to avoid rotor warping.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the Coated Single Pack Rotor SP12149, are manufactured to meet strict quality standards for fitment and performance. The rust-resistant coating is applied to enhance longevity and maintain braking reliability. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship. Always consult the product documentation or manufacturer for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384197513397,"sku":"CNJW-SP12149","price":61.09,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12149_Fro.jpg?v=1774633350"},{"product_id":"ate-sp12151-disc-brake-rotor","title":"ATE SP12151 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12151\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12151 is engineered for reliable braking performance on select Volvo models. Designed as a solid disc brake rotor with a rust-resistant coating, it offers durability and consistent stopping power for vehicles like the Volvo S60, V70, XC70, and S80.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 11.90 mm ensuring proper rotor wear limits\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support even pad wear\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 288.00 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eHeight: 2.913 inches for correct caliper clearance\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid, suitable for standard braking applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to combat rust and corrosion, which is especially beneficial in climates prone to moisture and road salt. This product line includes full cast solid rotors like the SP12151, designed to maintain structural integrity and consistent braking performance over time. The coating enhances rotor longevity without altering the rotor's original specifications.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP12151 rotor is a solid disc brake rotor constructed from metal with a full cast design, ensuring durability and reliable heat management during braking. Its nominal thickness of 11.90 mm meets OEM specifications, helping maintain proper braking efficiency and rotor lifespan. The non-directional disc finish promotes even brake pad wear, while the rust-resistant coating protects the rotor surface from corrosion, which can otherwise lead to premature rotor failure. With an outside diameter of 288.00 mm and a height of 2.913 inches, this rotor is engineered to fit securely on compatible Volvo models, including the S60, V70, XC70, and S80. The 5 mm bolt hole diameter ensures proper mounting and alignment with the vehicle’s hub assembly.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVolvo S60 brake rotor replacement\u003c\/li\u003e\n\u003cli\u003eVolvo V70 disc brake rotor upgrade\u003c\/li\u003e\n\u003cli\u003eVolvo XC70 front brake rotor maintenance\u003c\/li\u003e\n\u003cli\u003eVolvo S80 solid rotor replacement\u003c\/li\u003e\n\u003cli\u003eAddressing rotor wear and corrosion on Volvo models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify rotor thickness and dimensions before installation\u003c\/li\u003e\n\u003cli\u003eEnsure proper cleaning of hub surface to prevent rotor runout\u003c\/li\u003e\n\u003cli\u003eUse recommended torque specifications for bolt installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if worn to avoid uneven rotor wear\u003c\/li\u003e\n\u003cli\u003eCheck for proper caliper alignment and clearance with rotor height\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP12151, are manufactured to meet strict quality standards for fit, form, and function. The rust-resistant coating is applied to extend rotor life under typical driving conditions. While specific warranty details may vary, ATE products generally come with a limited warranty against manufacturing defects. It is recommended to consult the product documentation or supplier for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384197841077,"sku":"CNJW-SP12151","price":60.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12151_Fro_3d7263d2-1972-4a09-b356-932361510557.jpg?v=1774633351"},{"product_id":"ate-sp12152-disc-brake-rotor","title":"ATE SP12152 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12152 for BMW X5\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12152 is designed specifically for the BMW X5, providing reliable braking performance with durable construction. This disc brake rotor features a rust-resistant coating and solid design to meet the demands of everyday driving and maintain consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.00 mm for optimal wear life\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for consistent braking\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 324.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 3.515 mm for proper alignment and clearance\u003c\/li\u003e\n\u003cli\u003eType: Solid disc brake rotor designed for BMW X5\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, which is essential for maintaining rotor integrity over time. This product line includes full cast solid rotors like the SP12152, engineered to meet the exact specifications required by BMW X5 models. The coating enhances durability without compromising braking performance.\u003c\/p\u003e\u003ch2\u003eTechnical Description of the SP12152 Rotor\u003c\/h2\u003e\u003cp\u003eThe SP12152 rotor is a solid disc brake rotor constructed from metal with a nominal thickness of 12.00 mm, ensuring a balance between durability and heat dissipation. Its full cast construction provides structural integrity, while the non-directional disc finish allows for flexible installation on either side of the vehicle. The rotor’s 324.00 mm outside diameter and 3.515 mm height are designed to match BMW X5 factory specifications. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, which can affect braking efficiency and rotor lifespan.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW X5 models\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency by eliminating rotor surface corrosion\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor wear\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003ePrevents premature rotor failure due to rust and environmental exposure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12152 on a BMW X5, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows installation on either side without concern for directional rotation. Verify bolt hole alignment with the 5 mm diameter holes for proper fitment. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Always torque bolts to manufacturer specifications and check for any signs of uneven wear after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP12152, are manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating is applied to extend rotor life under typical driving conditions. While specific warranty details are not provided here, ATE products generally come with manufacturer-backed quality assurance to ensure reliability and performance when installed according to guidelines.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384203444405,"sku":"CNJW-SP12152","price":85.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12152_Fro_67cc7424-9d22-406e-8140-cdeb0ff27dd7.jpg?v=1774633351"},{"product_id":"ate-sp12154-disc-brake-rotor","title":"ATE SP12154 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12154\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12154 is engineered for Jaguar X-Type vehicles requiring reliable disc brake performance. This solid rotor features a rust-resistant coating and precise dimensions to ensure consistent braking efficiency and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.00 mm for optimal wear life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 280.00 mm to match Jaguar X-Type specifications\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to allow flexible installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eHeight: 2.330 inches for proper fitment\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12154 is a solid disc brake rotor designed specifically for the Jaguar X-Type. Manufactured from durable metal with a full cast construction, this rotor provides consistent braking performance under various driving conditions. The non-directional disc finish allows for versatile installation without concern for rotor orientation. Its nominal thickness of 12.00 mm and outside diameter of 280.00 mm ensure compatibility with the Jaguar X-Type braking system. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, maintaining braking efficiency over time.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on delivering rotors with protective coatings to enhance corrosion resistance and longevity. This product line includes solid rotors like the SP12154, which are designed for vehicles such as the Jaguar X-Type that require precise fitment and reliable braking components. The coating applied to these rotors helps reduce rust formation, which is particularly beneficial in environments prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Jaguar X-Type models\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing corrosion-related rotor degradation\u003c\/li\u003e\n\u003cli\u003eImproving braking consistency and pedal feel\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with exact bolt hole and diameter specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify rotor dimensions against vehicle specifications before installation\u003c\/li\u003e\n\u003cli\u003eEnsure the rotor surface is clean and free of contaminants prior to mounting\u003c\/li\u003e\n\u003cli\u003eUse proper torque settings on bolts to avoid rotor distortion\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary during rotor installation\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to optimize braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the Coated Single Pack Rotor SP12154, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to extend rotor life and maintain braking efficiency. Warranty coverage details should be confirmed with the product documentation or supplier, as they may vary by region.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384205705397,"sku":"CNJW-SP12154","price":54.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12154_Fro_0e427c7e-d2af-4b66-95e8-ea29e06ceba1.jpg?v=1774633351"},{"product_id":"ate-sp12157-disc-brake-rotor","title":"ATE SP12157 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12157\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12157 is designed specifically for Saab 9-3 models, providing reliable braking performance with a durable metal construction. This solid disc brake rotor features a rust-resistant coating to help extend its service life under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal for strength and durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 11.90 mm ensuring consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 278.00 mm matching Saab 9-3 specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.311 inches for proper alignment\u003c\/li\u003e\n\u003cli\u003eType: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing high-quality disc brake rotors with protective coatings to resist rust and corrosion. This product line is engineered to maintain braking efficiency and rotor longevity, making it suitable for vehicles like the Saab 9-3 that require precise fitment and reliable performance. The SP12157 part number is part of this line, ensuring consistent standards in material and finish.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12157 is a full cast, solid disc brake rotor designed to meet the exact specifications of the Saab 9-3. Its nominal thickness of 11.90 mm provides a stable braking surface, while the 278 mm outside diameter ensures compatibility with the vehicle’s braking system. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor from environmental factors, reducing the risk of corrosion and extending the rotor’s usable life.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Saab 9-3 models\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing rust buildup that can impair braking performance\u003c\/li\u003e\n\u003cli\u003eEnsuring proper rotor thickness for safe braking operation\u003c\/li\u003e\n\u003cli\u003eProviding a solid rotor option for vehicles not requiring vented rotors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with Saab 9-3 before installation\u003c\/li\u003e\n\u003cli\u003eEnsure rotor surface and hub are clean and free of debris\u003c\/li\u003e\n\u003cli\u003eCheck bolt hole diameter (5 mm) for proper fitment\u003c\/li\u003e\n\u003cli\u003eUse recommended torque specifications for mounting bolts\u003c\/li\u003e\n\u003cli\u003eInspect brake pads for wear and replace if necessary during rotor installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12157 is manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating is applied to enhance durability and maintain braking performance over time. While specific warranty details are not provided, ATE products typically adhere to strict quality control processes to ensure reliability and safety for Saab 9-3 vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384209014965,"sku":"CNJW-SP12157","price":53.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12157_Fro_fc98fa4e-1c1d-490d-a929-8669cfcf64d3.jpg?v=1774633351"},{"product_id":"ate-sp12158-disc-brake-rotor","title":"ATE SP12158 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12158\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12158 is designed for reliable braking performance on Volkswagen Jetta and Audi A3 models. This solid disc brake rotor features a rust-resistant coating and precise dimensions to ensure compatibility and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.00 mm for consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm to match vehicle specifications\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for durability\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 256.00 mm for exact fitment\u003c\/li\u003e\n\u003cli\u003eHeight: 2.267 inches to maintain proper clearance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing high-quality, coated rotors that resist rust and corrosion, extending the service life of the braking components. This product line is engineered to meet the exact specifications of European vehicles such as Volkswagen and Audi, ensuring reliable fitment and performance. The SP12158 rotor benefits from this coating technology, making it suitable for drivers seeking maintenance-friendly brake parts.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Compatibility\u003c\/h2\u003e\u003cp\u003eThe SP12158 disc brake rotor is a solid, full cast metal rotor with a nominal thickness of 12.00 mm and an outside diameter of 256.00 mm. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. The 5 mm bolt hole diameter matches the mounting requirements of Volkswagen Jetta and Audi A3 models, ensuring a secure fit. The rust-resistant coating helps protect the rotor surface from corrosion, which is especially beneficial in climates prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volkswagen Jetta and Audi A3\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing rust buildup that can affect braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestoring proper brake pedal feel and stopping power\u003c\/li\u003e\n\u003cli\u003eEnsuring compatibility with OEM brake components for safe operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12158, ensure the rotor surface is clean and free of debris before mounting. Use the correct torque specifications for the 5 mm bolt holes to avoid warping. The non-directional finish allows installation on either side, simplifying the replacement process. It is recommended to inspect brake pads and hardware during rotor replacement to maintain optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent thickness and dimensional accuracy. The rust-resistant coating adds an extra layer of protection against corrosion, contributing to longer rotor life. While specific warranty details for part number SP12158 should be confirmed with the supplier, ATE products typically come with manufacturer-backed quality guarantees to support professional automotive repairs.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384213471413,"sku":"CNJW-SP12158","price":50.26,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12158_Fro_2cd3e850-31a1-4efc-98b4-e69349033832.jpg?v=1774633352"},{"product_id":"ate-sp12159-disc-brake-rotor","title":"ATE SP12159 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12159\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12159 is designed specifically for Audi A6 and A6 Quattro models. This solid disc brake rotor features a rust-resistant coating and precise dimensions to ensure reliable braking performance and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi A6 and A6 Quattro\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with full cast construction\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for extended service life\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for consistent braking\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 12.00 mm and outside diameter of 301.70 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 2.319 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12159 is constructed from high-quality metal with a full cast design, providing structural integrity and consistent performance. Its solid rotor type is suitable for applications where vented rotors are not required. The non-directional disc finish allows for uniform wear and braking response regardless of rotor orientation. The rotor measures 301.70 mm in outside diameter and maintains a nominal thickness of 12.00 mm, ensuring compatibility with the braking system of Audi A6 and A6 Quattro vehicles. Additionally, the 5 mm bolt hole diameter and 2.319-inch height are engineered to match factory specifications.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings to resist rust and corrosion. This coating extends the rotor's lifespan and maintains braking efficiency over time, especially in environments prone to moisture and road salt exposure. The SP12159 rotor benefits from this coating, making it a practical replacement part for Audi A6 and A6 Quattro owners seeking durability and consistent braking performance.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi A6 and A6 Quattro\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking distances\u003c\/li\u003e\n\u003cli\u003eEliminates noise and vibration related to damaged rotors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12159, ensure the rotor surface is clean and free of debris before mounting. Verify that the bolt hole diameter and rotor height match the vehicle specifications. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Proper torque settings should be applied to all fasteners to avoid rotor warping or uneven wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and safety. The rust-resistant coating is applied uniformly to protect against corrosion. While specific warranty details for part number SP12159 should be confirmed with the supplier, ATE products typically come with a limited warranty covering manufacturing defects.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384214028469,"sku":"CNJW-SP12159","price":64.72,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12159_Fro_89f97525-b35f-440b-ba91-f9ac2cbe35c4.jpg?v=1774633352"},{"product_id":"ate-sp12166-disc-brake-rotor","title":"ATE SP12166 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12166\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12166 is engineered for reliable braking performance on Audi A4 and A4 Quattro models. Designed as a solid disc brake rotor, it features a rust-resistant coating to enhance durability and maintain consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi A4 and A4 Quattro vehicles\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with 288 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction for strength and stability\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for uniform wear\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to prevent corrosion\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 12.00 mm and height of 2.251 inches\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm for secure fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThis ATE Coated Single Pack Rotor SP12166 is manufactured from high-quality metal with a full cast construction, ensuring structural integrity and consistent braking performance. The rotor measures 288 mm in outside diameter and maintains a nominal thickness of 12.00 mm, which supports effective heat dissipation during braking. Its solid rotor design is suited for applications where vented rotors are not required. The non-directional disc finish promotes even pad wear and reduces noise. Additionally, the rust-resistant coating extends the rotor's service life by protecting against corrosion, an important factor for Audi A4 and A4 Quattro owners driving in varied weather conditions.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, enhancing longevity and maintaining braking efficiency. This product line is designed to meet the demands of European vehicles like Audi, offering rotors that combine durability with consistent performance. The SP12166 rotor exemplifies this approach with its full cast metal construction and protective coating, tailored for the braking systems of Audi A4 and A4 Quattro models.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi A4 and A4 Quattro\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can reduce braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eImproves brake pedal feel by eliminating rotor vibration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12166, ensure the rotor surface is clean and free of debris before mounting. Verify the bolt hole diameter matches the vehicle specifications for a secure fit. It is recommended to replace brake pads simultaneously to optimize braking performance. Proper torque specifications should be followed to avoid rotor warping. This rotor is designed for direct replacement on compatible Audi A4 and A4 Quattro models.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and safety. The rust-resistant coating is applied to extend the rotor's lifespan under normal operating conditions. While specific warranty details for part number SP12166 should be confirmed with the supplier, ATE products typically come with a limited warranty covering manufacturing defects.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384215240885,"sku":"CNJW-SP12166","price":56.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12166_Fro_9dc6dd44-3d15-48f1-8809-013ac10fb632.jpg?v=1774633352"},{"product_id":"ate-sp12175-disc-brake-rotor","title":"ATE SP12175 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12175\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12175 is engineered for reliable braking performance on Audi TT and TT Quattro models. Designed with a rust-resistant coating and solid construction, this disc brake rotor ensures consistent stopping power and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Audi TT and TT Quattro\u003c\/li\u003e\n\u003cli\u003eSolid disc brake rotor with 286 mm outside diameter\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction with 12.00 mm nominal thickness\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm for secure fitment\u003c\/li\u003e\n\u003cli\u003eHeight of 2.661 inches for precise fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12175 is a solid disc brake rotor made from durable metal with a full cast construction. Its nominal thickness of 12.00 mm and outside diameter of 286 mm are designed to meet the exact specifications required for Audi TT and TT Quattro vehicles. The rotor features a non-directional disc finish, allowing for flexible installation without concern for directional wear patterns. Additionally, the rotor is coated with a rust-resistant layer to help prevent corrosion and maintain braking efficiency over time. The bolt hole diameter measures 5 mm, ensuring a secure and precise fit during installation. With a height of 2.661 inches, this rotor aligns with factory standards for optimal performance.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, extending the service life of the brake components. This product line emphasizes durability and consistent braking performance, making it suitable for vehicles like the Audi TT and TT Quattro that require reliable stopping power under various driving conditions. The SP12175 part number is part of this line, offering a solid rotor design with a full cast metal construction and a protective coating.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Audi TT and TT Quattro\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eHelps reduce rust buildup that can impair braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003eImproves brake pedal feel by eliminating rotor vibration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP12175, ensure the rotor surface is clean and free of debris before mounting. Use the correct torque specifications for the 5 mm bolt holes to secure the rotor properly. Since the rotor has a non-directional finish, it can be installed on either side without concern for directional rotation. It is recommended to inspect brake pads and hardware during installation to ensure optimal braking system performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring compatibility and performance for Audi TT and TT Quattro vehicles. The rust-resistant coating provides added protection against corrosion, contributing to the rotor's longevity. Warranty details should be confirmed with the supplier or manufacturer, as coverage may vary based on region and purchase conditions.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384216289461,"sku":"CNJW-SP12175","price":44.66,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12175_Fro_70188a0d-6499-49a8-ac1f-97a308b145fd.jpg?v=1774633353"},{"product_id":"ate-sp12183-disc-brake-rotor","title":"ATE SP12183 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP12183\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12183 is engineered for Mercedes-Benz models including the S400, SL550, and S550. Designed as a solid disc brake rotor, it offers reliable braking performance with a rust-resistant coating to extend service life.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 300.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes\u003c\/li\u003e\n\u003cli\u003eHeight: 2.547 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist corrosion and wear. This coating helps maintain rotor integrity and braking efficiency over time, especially important for vehicles like the Mercedes-Benz S400, SL550, and S550 that demand consistent performance. The full cast solid construction ensures structural strength and compatibility with original equipment specifications.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Specifications\u003c\/h2\u003e\u003cp\u003eThis disc brake rotor features a solid design with a nominal thickness of 12.00 mm and an outside diameter of 300.00 mm, suitable for specific Mercedes-Benz models. The non-directional disc finish allows for flexible installation without concern for rotor orientation. The bolt hole diameter of 5 mm matches factory mounting points, ensuring a secure fit. The rotor’s height measures 2.547 inches, aligning with OEM dimensions. The rust-resistant coating protects the metal surface from corrosion, which is critical for maintaining braking performance and rotor longevity.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz S400, SL550, and S550\u003c\/li\u003e\n\u003cli\u003eAddresses brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust and corrosion that can degrade braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores proper brake pad contact and stopping power\u003c\/li\u003e\n\u003cli\u003eSuitable for vehicles requiring solid disc rotors with OEM specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Mercedes-Benz S400, SL550, and S550 models before installation\u003c\/li\u003e\n\u003cli\u003eCheck rotor thickness and surface condition during replacement\u003c\/li\u003e\n\u003cli\u003eUse proper torque specifications for bolt hole diameter of 5 mm\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to prevent uneven rotor seating\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear when replacing rotors\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP12183 is manufactured to meet OEM standards for fit and function. The rust-resistant coating is applied to enhance durability under typical driving conditions. While specific warranty details are not provided, ATE products generally adhere to strict quality control processes to ensure reliability and performance in Mercedes-Benz braking systems.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384216354997,"sku":"CNJW-SP12183","price":69.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP12183_Fro_5cd38e4d-de30-4790-82c2-6afd94e7962e.jpg?v=1774633353"},{"product_id":"ate-sp13197-disc-brake-rotor","title":"ATE SP13197 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP13197\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP13197 is engineered for reliable braking performance on Land Rover Discovery and Range Rover models. Designed with durability and precision, this disc brake rotor meets the demands of these specific vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat resistance\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 12.50 mm ensuring consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 304.00 mm matching factory specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.838 mm for proper fitment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc for standard braking applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion. This coating helps maintain rotor integrity over time, especially in environments prone to moisture and road salt. The SP13197 rotor benefits from this coating, making it suitable for Land Rover Discovery and Range Rover vehicles that require dependable braking components.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Fitment\u003c\/h2\u003e\u003cp\u003eThis disc brake rotor is specifically designed for Land Rover Discovery and Range Rover models, ensuring compatibility and optimal performance. The full cast metal construction provides a solid and durable braking surface, while the non-directional disc finish allows for flexible installation without concern for rotor orientation. The nominal thickness of 12.50 mm and outside diameter of 304.00 mm align with OEM specifications, maintaining proper brake system function. Additionally, the rust resistant coating extends the rotor's service life by protecting against corrosion.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Land Rover Discovery and Range Rover\u003c\/li\u003e\n\u003cli\u003eAddressing brake pulsation caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eReducing rust and corrosion buildup on brake rotors\u003c\/li\u003e\n\u003cli\u003eRestoring braking efficiency and pedal feel\u003c\/li\u003e\n\u003cli\u003eEnsuring proper fitment with bolt hole diameter and rotor dimensions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP13197, ensure the rotor is clean and free of any protective oils before mounting. The non-directional finish allows installation on either side without concern for rotation direction. Verify bolt hole alignment with the vehicle hub and torque bolts to manufacturer specifications. It is recommended to replace brake pads simultaneously to maintain balanced braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust resistant coating is applied to enhance longevity under typical driving conditions. While specific warranty details for part number SP13197 should be confirmed with the supplier, ATE products generally come with manufacturer-backed quality assurance to support reliable operation on Land Rover Discovery and Range Rover vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384217600181,"sku":"CNJW-SP13197","price":73.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP13197_Fro_57990a51-2bd5-424b-8129-443dfa75490e.jpg?v=1774633353"},{"product_id":"ate-sp14111-disc-brake-rotor","title":"ATE SP14111 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP14111\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP14111 is engineered for Mercedes-Benz ML500, ML55 AMG, and ML430 models. This solid disc brake rotor features a rust-resistant coating and full cast construction, designed to maintain reliable braking performance under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 13.90 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 331.00 mm\u003c\/li\u003e\n\u003cli\u003eHeight: 2.539 mm\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing durable, corrosion-resistant rotors suitable for specific vehicle applications. The rust-resistant coating on the SP14111 helps extend rotor life by protecting against environmental factors, while the full cast construction ensures structural integrity. This product line is designed to meet the precise specifications required for Mercedes-Benz ML series vehicles, ensuring compatibility and consistent braking performance.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Features\u003c\/h2\u003e\u003cp\u003eThe SP14111 rotor is a solid disc brake rotor made from metal with a nominal thickness of 13.90 mm, providing a stable braking surface. Its 331 mm outside diameter and 2.539 mm height are tailored for the braking system of Mercedes-Benz ML500, ML55 AMG, and ML430 models. The non-directional disc finish allows for flexible installation without concern for rotor orientation. The full cast construction enhances durability, while the rust-resistant coating protects the rotor from corrosion, which is critical for maintaining braking efficiency over time.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Mercedes-Benz ML500, ML55 AMG, and ML430\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eHelps reduce brake fade by maintaining consistent rotor thickness\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation\u003c\/li\u003e\n\u003cli\u003eEnsures proper fitment with bolt hole diameter of 5 mm for secure installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP14111, ensure the rotor is compatible with your Mercedes-Benz ML model year and brake system. The non-directional finish allows installation on either side without concern for directional wear patterns. It is recommended to inspect brake pads and hardware during rotor replacement to maintain optimal braking performance. Proper torque specifications should be followed for the 5 mm bolt holes to secure the rotor safely.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust-resistant coating on the SP14111 rotor adds an extra layer of protection against corrosion. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384217698485,"sku":"CNJW-SP14111","price":82.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP14111_Fro.jpg?v=1774633356"},{"product_id":"ate-sp14114-disc-brake-rotor","title":"ATE SP14114 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP14114\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP14114 is engineered for reliable braking performance on select Mercedes-Benz models. Designed as a solid disc brake rotor with a rust-resistant coating, it offers durability and consistent stopping power for vehicles like the ML350 and R500.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat resistance\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 14.00 mm ensuring proper rotor thickness for braking efficiency\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to allow flexible installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor for durability\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 330.20 mm compatible with specified Mercedes-Benz models\u003c\/li\u003e\n\u003cli\u003eHeight: 2.838 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to combat rust and corrosion. This coating enhances the rotor's lifespan and maintains braking performance over time. The SP14114 model benefits from this technology, making it suitable for Mercedes-Benz vehicles that require reliable, long-lasting rotors.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP14114 disc brake rotor is a full cast, solid metal rotor designed specifically for Mercedes-Benz models including the R350, ML350, ML450, ML320, R320, ML500, and R500. Its nominal thickness of 14.00 mm ensures it meets OEM specifications for braking performance. The non-directional disc finish allows for flexible installation without concern for rotor orientation. The 5 mm bolt hole diameter and 330.20 mm outside diameter provide precise fitment, while the rust-resistant coating helps protect the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors causing brake pulsation\u003c\/li\u003e\n\u003cli\u003eUpgrading corroded rotors to improve braking reliability\u003c\/li\u003e\n\u003cli\u003eAddressing uneven brake pad wear due to rotor surface imperfections\u003c\/li\u003e\n\u003cli\u003eRestoring proper rotor thickness to maintain braking efficiency\u003c\/li\u003e\n\u003cli\u003eEnsuring compatibility with Mercedes-Benz R350, ML350, and related models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify rotor dimensions and bolt hole diameter match vehicle specifications\u003c\/li\u003e\n\u003cli\u003eEnsure the rotor surface is clean and free of debris before installation\u003c\/li\u003e\n\u003cli\u003eUse proper torque settings on mounting bolts to avoid rotor distortion\u003c\/li\u003e\n\u003cli\u003eCheck brake pads for wear and replace if necessary during rotor installation\u003c\/li\u003e\n\u003cli\u003eFollow manufacturer guidelines for bedding in new rotors and pads\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP14114, are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating is applied to extend rotor life under typical driving conditions. While specific warranty details are not provided here, ATE products generally come with manufacturer-backed warranties covering defects in materials and workmanship. It is recommended to consult the product packaging or manufacturer for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384218190005,"sku":"CNJW-SP14114","price":87.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP14114_Fro_40b42d1b-f529-47cc-800b-8dd74bf21643.jpg?v=1774633356"},{"product_id":"ate-sp14119-disc-brake-rotor","title":"ATE SP14119 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP14119\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP14119 is designed specifically for Mercedes-Benz models including the GLE350, GLE300d, ML250, and ML350. This solid disc brake rotor features a rust-resistant coating and precise construction to ensure reliable braking performance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 14.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional surface\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, for extended lifespan\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 325.00 mm\u003c\/li\u003e\n\u003cli\u003eHeight: 2.480 mm\u003c\/li\u003e\n\u003cli\u003eRotor Type: Solid disc brake rotor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line is engineered to provide corrosion resistance and consistent braking performance. The rust-resistant coating on the SP14119 rotor helps protect the metal surface from environmental wear, which is especially beneficial for vehicles like the Mercedes-Benz GLE350 and ML350 that require dependable stopping power under various driving conditions.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Features\u003c\/h2\u003e\u003cp\u003eThis full cast, solid disc brake rotor is manufactured from high-quality metal and measures 325 mm in outside diameter with a nominal thickness of 14.00 mm. The non-directional disc finish allows for versatile installation without concern for rotor orientation. The 5 mm bolt hole diameter ensures compatibility with the specified Mercedes-Benz models. The rotor’s height of 2.480 mm supports proper fitment and brake system alignment.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement rotor for Mercedes-Benz GLE350 brake system maintenance\u003c\/li\u003e\n\u003cli\u003eSuitable for Mercedes-Benz GLE300d brake rotor replacement\u003c\/li\u003e\n\u003cli\u003eUsed in Mercedes-Benz ML250 brake repairs\u003c\/li\u003e\n\u003cli\u003eCompatible with Mercedes-Benz ML350 brake rotor upgrades\u003c\/li\u003e\n\u003cli\u003eAddresses rotor wear, corrosion, and brake noise issues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP14119, ensure the rotor surface is clean and free of debris. Verify bolt hole alignment with the vehicle hub and torque bolts to manufacturer specifications. The non-directional finish allows installation on either side without performance impact. It is recommended to inspect brake pads and hardware during rotor replacement for optimal braking results.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards for durability and performance. The rust-resistant coating extends rotor life by reducing corrosion. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384219173045,"sku":"CNJW-SP14119","price":91.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP14119_Fro_fc5f002f-9bb9-4c0f-a091-43c84390edc1.jpg?v=1774633356"},{"product_id":"ate-sp15111-disc-brake-rotor","title":"ATE SP15111 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP15111\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP15111 is engineered for reliable braking performance on select Mercedes-Benz models. Designed as a solid disc brake rotor, it offers durability and corrosion resistance tailored for vehicles like the ML350, ML320, and ML430.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 15.00 mm ensuring consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to support uniform wear\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast solid rotor design\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 285.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.555 inches for proper caliper clearance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to reduce corrosion and maintain braking efficiency over time. This product line includes solid rotors constructed from full cast metal, designed to meet the exacting standards required for Mercedes-Benz vehicles. The coating applied to the SP15111 rotor helps prevent rust buildup, which is critical for maintaining consistent braking performance and rotor longevity.\u003c\/p\u003e\u003ch2\u003eProduct Description and Fitment\u003c\/h2\u003e\u003cp\u003eThe SP15111 disc brake rotor is a solid, full cast metal rotor with a nominal thickness of 15.00 mm and an outside diameter of 285.00 mm. Its non-directional disc finish supports even pad wear and braking consistency. The rotor’s 5 mm bolt hole diameter ensures a secure fit on Mercedes-Benz ML350, ML320, and ML430 models. The rust resistant coating protects the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure. This rotor is designed to replace original equipment parts, maintaining factory specifications for height and thickness to ensure proper brake system function.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors causing brake pulsation\u003c\/li\u003e\n\u003cli\u003eUpgrading corroded rotors to improve braking reliability\u003c\/li\u003e\n\u003cli\u003eAddressing uneven brake pad wear due to rotor surface imperfections\u003c\/li\u003e\n\u003cli\u003eRestoring proper rotor thickness for safe braking performance\u003c\/li\u003e\n\u003cli\u003ePreventing rust-related rotor damage in Mercedes-Benz ML series vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP15111, ensure the rotor surface and hub are clean and free of debris. Verify the rotor thickness meets or exceeds manufacturer minimums before installation. Use proper torque specifications for the 5 mm bolt holes to secure the rotor. It is recommended to replace brake pads simultaneously to ensure optimal braking performance. After installation, perform a bed-in procedure to allow the pads and rotor to mate correctly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring compatibility and performance for Mercedes-Benz ML350, ML320, and ML430 models. The rust resistant coating is applied to extend rotor life and maintain braking efficiency. Warranty details should be confirmed with the distributor or manufacturer, as coverage may vary.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384219271349,"sku":"CNJW-SP15111","price":64.65,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP15111_Fro_f4057f23-8454-4ebb-83f6-db6b6143aa30.jpg?v=1774633357"},{"product_id":"ate-sp16110-disc-brake-rotor","title":"ATE SP16110 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP16110\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP16110 is designed for reliable braking performance on select Mercedes-Benz and Dodge vehicles. Engineered with a rust-resistant coating and solid construction, this disc brake rotor meets the demands of models like the Mercedes-Benz G550 and Dodge Sprinter 3500.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal with rust-resistant coating\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 16.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 272.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast, solid rotor type\u003c\/li\u003e\n\u003cli\u003eHeight: 4.173 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe SP16110 rotor from ATE features a full cast metal construction that ensures structural integrity and consistent braking performance. Its solid disc design provides a stable braking surface, while the non-directional finish allows for flexible installation without concern for rotor orientation. The rotor measures 272 mm in outside diameter and maintains a nominal thickness of 16.00 mm, suitable for the braking systems of Mercedes-Benz G55 AMG and Dodge Sprinter 2500 models. Additionally, the rust-resistant coating extends the rotor's service life by protecting against corrosion, which is especially beneficial in varying weather conditions.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on delivering rotors with enhanced durability through protective coatings. This line is designed to reduce rust formation and maintain rotor integrity over time, making it a practical choice for vehicles like the Mercedes-Benz G500 and Dodge Sprinter 3500. The SP16110 part number represents a solid rotor option within this line, balancing performance and longevity for disc brake applications.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMercedes-Benz G550 brake rotor replacement\u003c\/li\u003e\n\u003cli\u003eMercedes-Benz G55 AMG disc brake rotor upgrade\u003c\/li\u003e\n\u003cli\u003eMercedes-Benz G500 rotor maintenance part\u003c\/li\u003e\n\u003cli\u003eDodge Sprinter 2500 brake system component\u003c\/li\u003e\n\u003cli\u003eDodge Sprinter 3500 rotor replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE SP16110 rotor, ensure the rotor surface is clean and free of debris before mounting. The non-directional disc finish allows installation without concern for rotor orientation, simplifying the process. Verify bolt hole alignment with the vehicle hub, as the rotor features a 5 mm bolt hole diameter. It is recommended to inspect brake pads and hardware during installation to maintain optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE manufactures the SP16110 rotor to meet strict quality standards, ensuring consistent performance and durability. The rust-resistant coating is applied to extend rotor life under typical driving conditions. While specific warranty details are not provided, ATE products generally adhere to industry standards for material and workmanship quality.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384219697333,"sku":"CNJW-SP16110","price":95.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP16110_Fro_deb9cca8-b7d6-4fdb-bc2e-3d3df37d5f92.jpg?v=1774633357"},{"product_id":"ate-sp19107-disc-brake-rotor","title":"ATE SP19107 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP19107\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19107 is engineered for reliable braking performance on select BMW models. Designed specifically for BMW 323Ci, 323i, and 328i vehicles, this vented disc brake rotor offers durability and consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-quality metal construction\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 19.00 mm for optimal wear resistance\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 276.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.728 inches\u003c\/li\u003e\n\u003cli\u003eRotor Type: Vented for improved cooling\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with a protective rust-resistant coating to extend service life and maintain braking efficiency. This product line emphasizes full cast construction and vented rotor design, which helps manage heat buildup during braking. The SP19107 rotor is part of this line, offering a balance of durability and performance tailored for BMW 3 Series models.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Features\u003c\/h2\u003e\u003cp\u003eThe SP19107 rotor is constructed from metal with a full cast design, providing structural integrity and effective heat dissipation. Its vented design allows air to flow between the rotor surfaces, reducing the risk of brake fade during extended use. The nominal thickness of 19.00 mm ensures the rotor maintains its strength and performance over time. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCompatible with BMW 323Ci models\u003c\/li\u003e\n\u003cli\u003eCompatible with BMW 323i models\u003c\/li\u003e\n\u003cli\u003eCompatible with BMW 328i models\u003c\/li\u003e\n\u003cli\u003eDesigned for use as a front or rear disc brake rotor depending on vehicle specifications\u003c\/li\u003e\n\u003cli\u003eSuitable for replacement of worn or damaged rotors to restore braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure proper torque specifications are followed when installing the rotor\u003c\/li\u003e\n\u003cli\u003eCheck for compatibility with existing brake pads and calipers on BMW 323Ci, 323i, and 328i\u003c\/li\u003e\n\u003cli\u003eInspect hub surface for cleanliness and flatness before installation\u003c\/li\u003e\n\u003cli\u003eIt is recommended to replace rotors in pairs to maintain balanced braking\u003c\/li\u003e\n\u003cli\u003eAllow the rust-resistant coating to wear off naturally during initial use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19107 is manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating and full cast construction contribute to the rotor’s durability and consistent performance. While specific warranty details are not provided, ATE products typically adhere to industry quality controls to ensure reliability and safety for BMW 3 Series vehicles.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384219762869,"sku":"CNJW-SP19107","price":68.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP19107_Fro_a69a07c9-0313-4504-8fe0-0d49a23a138a.jpg?v=1774633357"},{"product_id":"ate-sp19108-disc-brake-rotor","title":"ATE SP19108 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP19108\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19108 is engineered for reliable braking performance on select BMW models. Designed with a rust-resistant coating and vented construction, this disc brake rotor supports consistent heat dissipation and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and longevity\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 18.90 mm ensuring proper rotor thickness for braking efficiency\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm for secure mounting\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional to allow flexible installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend rotor life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 294.00 mm compatible with specified BMW models\u003c\/li\u003e\n\u003cli\u003eHeight: 2.716 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Vented to improve heat dissipation during braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings that help resist rust and corrosion. This coating enhances the rotor's lifespan and maintains braking performance over time. The SP19108 rotor benefits from this technology, making it suitable for BMW 3 Series vehicles that require reliable and durable braking components.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Compatibility\u003c\/h2\u003e\u003cp\u003eThe SP19108 disc brake rotor is a vented, full cast metal rotor with a nominal thickness of 18.90 mm and an outside diameter of 294 mm. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. The 5 mm bolt hole diameter ensures compatibility with the mounting hardware on BMW 325Ci, 325i, 323Ci, 323i, 328Ci, and 328i models. The rust-resistant coating protects the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW 3 Series models\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency by maintaining proper rotor thickness\u003c\/li\u003e\n\u003cli\u003eReduces brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can lead to rotor degradation\u003c\/li\u003e\n\u003cli\u003eSupports heat dissipation to avoid brake fade during extended use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP19108, ensure the rotor surface is clean and free of debris. The non-directional finish allows installation on either side, simplifying the process. Verify bolt hole alignment with the vehicle hub and torque bolts to manufacturer specifications. It is recommended to replace brake pads simultaneously to ensure optimal braking performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring durability and performance. The rust-resistant coating adds an extra layer of protection against environmental factors. Please refer to ATE's official warranty policy for coverage details related to the SP19108 rotor.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384220254389,"sku":"CNJW-SP19108","price":74.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP19108_Fro_9f620249-03f9-40c0-acd0-1f41c281e704.jpg?v=1774633358"},{"product_id":"ate-sp19112-disc-brake-rotor","title":"ATE SP19112 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP19112\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19112 is engineered for BMW Z4 models requiring reliable braking performance. This vented disc brake rotor features a rust-resistant coating and precise dimensions to ensure optimal fit and function.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 19.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 294.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design\u003c\/li\u003e\n\u003cli\u003eHeight: 3.307 inches\u003c\/li\u003e\n\u003cli\u003eType: Vented rotor with rust-resistant coating\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19112 is a full cast, vented disc brake rotor designed specifically for the BMW Z4. Its metal construction provides strength and heat dissipation, while the vented design helps reduce brake fade during extended use. The rotor measures 294 mm in outside diameter with a nominal thickness of 19.00 mm, ensuring compatibility with the vehicle's braking system. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating extends the rotor's service life by protecting against corrosion, which is especially beneficial in varying weather conditions.\u003c\/p\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings to enhance durability and maintain braking efficiency over time. This line is designed to meet the demands of drivers who require consistent performance and longevity from their brake components.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCompatible with BMW Z4 models requiring a 294 mm vented disc brake rotor\u003c\/li\u003e\n\u003cli\u003eIdeal replacement for worn or damaged rotors on BMW Z4\u003c\/li\u003e\n\u003cli\u003eSuitable for addressing issues such as brake noise, vibration, and reduced stopping power\u003c\/li\u003e\n\u003cli\u003eHelps restore proper braking performance and pedal feel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the rotor matches the vehicle specifications before installation\u003c\/li\u003e\n\u003cli\u003eCheck for proper bolt hole alignment with a 5 mm diameter\u003c\/li\u003e\n\u003cli\u003eClean the rotor surface before mounting to remove any protective coating residue\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid warping\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if necessary to ensure optimal contact\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and safety. The rust-resistant coating is applied to extend rotor life and maintain braking efficiency. While specific warranty details for part number SP19112 should be confirmed with the supplier, ATE products typically come with a limited warranty covering manufacturing defects.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384220319925,"sku":"CNJW-SP19112","price":85.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP19112_Fro_f9e68e1f-f107-4d7c-8f43-e637a1a0d0e7.jpg?v=1774633358"},{"product_id":"ate-sp19113-disc-brake-rotor","title":"ATE SP19113 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP19113\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19113 is engineered for reliable braking performance on BMW 325xi models. This vented disc brake rotor features a rust-resistant coating and precise construction to maintain consistent stopping power under various driving conditions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with BMW 325xi vehicles\u003c\/li\u003e\n\u003cli\u003ePart number: SP19113\u003c\/li\u003e\n\u003cli\u003eFull cast metal construction for durability\u003c\/li\u003e\n\u003cli\u003eVented rotor design for improved heat dissipation\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 19.00 mm and outside diameter of 294.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and height of 2.751 inches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP19113 is a vented disc brake rotor made from full cast metal, designed to provide consistent braking performance for the BMW 325xi. Its nominal thickness of 19.00 mm ensures structural integrity and longevity, while the 294.00 mm outside diameter matches OEM specifications for proper fitment. The rotor’s non-directional disc finish allows for flexible installation without concern for directional orientation. Additionally, the rotor includes a rust-resistant coating that helps protect against corrosion, extending the service life of the part. The bolt hole diameter measures 5 mm, and the rotor height is 2.751 inches, both critical dimensions for proper mounting and compatibility.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing high-quality replacement rotors with protective coatings to resist rust and corrosion. This product line is designed to meet the demands of modern vehicles like the BMW 325xi by combining durable full cast construction with vented designs that improve heat dissipation. The coating applied to these rotors helps maintain performance and appearance over time, making them a practical choice for maintaining braking efficiency.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW 325xi\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eHelps reduce brake fade through vented rotor design\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can impair braking performance\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP19113 on a BMW 325xi, ensure the rotor is clean and free of any protective oils before mounting. The non-directional finish allows installation on either side without concern for rotation direction. Verify that the bolt hole diameter and rotor height match OEM specifications to ensure proper fitment. It is recommended to replace brake pads simultaneously to optimize braking performance and rotor longevity.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust-resistant coating adds an extra layer of protection against corrosion. While specific warranty details for part number SP19113 should be confirmed with the supplier, ATE products typically come with a limited warranty covering defects in materials and workmanship.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384229134517,"sku":"CNJW-SP19113","price":76.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP19113_Fro_d4e33a61-87cf-4a11-b860-0bf1ced26663.jpg?v=1774633358"},{"product_id":"ate-sp20122-disc-brake-rotor","title":"ATE SP20122 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20122\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20122 is engineered for reliable braking performance on Volvo XC90 models. Designed with precision, this disc brake rotor offers durability and consistent stopping power tailored to your vehicle's specifications.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFull cast metal construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eVented rotor design to improve heat dissipation\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for uniform wear\u003c\/li\u003e\n\u003cli\u003eRust resistant coating to extend rotor life\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 20.00 mm for optimal braking surface\u003c\/li\u003e\n\u003cli\u003eOutside diameter of 308.00 mm matching Volvo XC90 requirements\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm for secure fitment\u003c\/li\u003e\n\u003cli\u003eHeight of 2.921 inches ensuring proper clearance and fit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20122 is constructed from high-quality metal with a full cast design, providing a robust and reliable braking surface. Its vented rotor type enhances heat dissipation during braking, reducing the risk of brake fade under demanding conditions. The non-directional disc finish promotes even pad wear and consistent braking performance. Additionally, the rotor features a rust resistant coating that helps protect against corrosion, extending the service life of the part. With a nominal thickness of 20.00 mm and an outside diameter of 308.00 mm, this rotor is specifically designed to meet the braking system requirements of the Volvo XC90. The bolt hole diameter of 5 mm and a height of 2.921 inches ensure proper installation and compatibility.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, which is essential for maintaining braking efficiency over time. This product line combines durable full cast construction with vented designs to balance strength and heat management. The SP20122 rotor is part of this line, offering a reliable replacement option for Volvo XC90 owners seeking rotors that maintain performance and longevity in various driving conditions.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volvo XC90 vehicles\u003c\/li\u003e\n\u003cli\u003eAddressing brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproving heat dissipation to reduce brake fade during heavy use\u003c\/li\u003e\n\u003cli\u003ePreventing rust and corrosion that can compromise braking efficiency\u003c\/li\u003e\n\u003cli\u003eEnsuring proper rotor thickness for safe and effective braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP20122, ensure the rotor surface is clean and free of debris before mounting. Verify that the bolt hole diameter and rotor height match the vehicle specifications to avoid fitment issues. It is recommended to replace brake pads simultaneously to maintain optimal braking performance. Proper torque specifications should be followed when securing the rotor to the hub. After installation, perform a brake bed-in procedure to ensure even pad and rotor contact.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors are manufactured to meet strict quality standards, ensuring consistent performance and durability. The rust resistant coating adds an extra layer of protection against environmental factors. While specific warranty details for part number SP20122 are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship. Consult the product documentation or manufacturer for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384229462197,"sku":"CNJW-SP20122","price":84.09,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20122_Fro_63deb575-a6bf-4609-a8ab-293060de6683.jpg?v=1774633359"},{"product_id":"ate-sp20128-disc-brake-rotor","title":"ATE SP20128 Disc Brake Rotor - Front","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20128\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20128 is designed for reliable braking performance on select Volkswagen models. Engineered with a rust-resistant coating and vented construction, this disc brake rotor supports consistent heat dissipation and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and longevity\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 20.00 mm for optimal braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 4 mm ensuring secure fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 256.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.354 mm for proper rotor alignment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Vented to improve heat dissipation during braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20128 is a vented disc brake rotor constructed from durable metal with a full cast design. Its 256 mm outside diameter and 20 mm nominal thickness meet the precise requirements for Volkswagen Cabrio, Golf, Jetta, Passat, and Quantum models. The non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating extends the rotor's service life by protecting against corrosion, which is especially beneficial in varying weather conditions. The 4 mm bolt hole diameter ensures a secure and exact fit to the vehicle's hub assembly.\u003c\/p\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor product line focuses on providing rotors with protective coatings to combat rust and corrosion. This line is designed to maintain rotor integrity and performance over time, reducing the need for frequent replacements. The SP20128 rotor exemplifies this approach by combining a vented design with a rust-resistant coating, making it suitable for Volkswagen vehicles requiring reliable braking components.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Volkswagen Cabrio, Golf, Jetta, Passat, and Quantum\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproves braking performance by restoring proper rotor thickness\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation in humid or wet environments\u003c\/li\u003e\n\u003cli\u003eHelps reduce brake fade through vented rotor design\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Volkswagen models Cabrio, Golf, Jetta, Passat, and Quantum before installation\u003c\/li\u003e\n\u003cli\u003eCheck rotor thickness and bolt hole alignment during installation\u003c\/li\u003e\n\u003cli\u003eUse proper torque specifications on bolts to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and replace if worn to ensure optimal rotor performance\u003c\/li\u003e\n\u003cli\u003eClean hub surface before mounting rotor to prevent uneven seating\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20128 is manufactured to meet OEM standards for fit and function. The rust-resistant coating and full cast construction contribute to the rotor's durability and consistent braking performance. Warranty details should be confirmed with the original equipment manufacturer or authorized distributor.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384229920949,"sku":"CNJW-SP20128","price":59.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20128_Fro_10fca082-cc7c-4986-9bb7-bcd5dcff4cd3.jpg?v=1774633359"},{"product_id":"ate-sp20154-disc-brake-rotor","title":"ATE SP20154 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20154\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20154 is engineered for BMW models including the 525i, 528i, 530i, and 540i. Designed as a vented disc brake rotor, it offers reliable braking performance with a rust-resistant coating to extend service life.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for durability\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 20.00 mm\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 298.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design\u003c\/li\u003e\n\u003cli\u003eHeight: 2.767 mm\u003c\/li\u003e\n\u003cli\u003eType: Vented rotor for improved heat dissipation\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion, which is critical for maintaining braking efficiency over time. This product line includes full cast, vented rotors like the SP20154, designed to meet the specific braking requirements of BMW vehicles. The coating enhances durability without compromising the rotor’s structural integrity or performance.\u003c\/p\u003e\u003ch2\u003eTechnical Description and Features\u003c\/h2\u003e\u003cp\u003eThe SP20154 rotor is constructed from metal with a full cast design, ensuring strength and consistent performance. Its vented design allows for better heat dissipation during braking, reducing the risk of brake fade. The nominal thickness of 20.00 mm and an outside diameter of 298.00 mm are tailored to fit BMW 525i, 528i, 530i, and 540i models precisely. The non-directional disc finish supports versatile installation without concern for rotor orientation. Additionally, the rust-resistant coating helps protect the rotor surface from corrosion, extending the rotor’s usable life and maintaining braking reliability.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement rotor for BMW 525i brake system maintenance\u003c\/li\u003e\n\u003cli\u003eSuitable for BMW 528i brake rotor upgrades or repairs\u003c\/li\u003e\n\u003cli\u003eCompatible with BMW 530i for improved brake rotor durability\u003c\/li\u003e\n\u003cli\u003eUsed in BMW 540i brake system to maintain consistent stopping power\u003c\/li\u003e\n\u003cli\u003eAddresses rotor wear, corrosion, and heat-related brake issues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with BMW 525i, 528i, 530i, or 540i before installation\u003c\/li\u003e\n\u003cli\u003eCheck rotor thickness and bolt hole diameter (5 mm) for proper fit\u003c\/li\u003e\n\u003cli\u003eFollow manufacturer torque specifications when mounting the rotor\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware during rotor replacement for optimal performance\u003c\/li\u003e\n\u003cli\u003eClean rotor surface before installation to remove any protective coatings or residues\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20154 is manufactured to meet OEM standards for fit and function on BMW vehicles. The rust-resistant coating is applied to enhance durability under typical driving conditions. While specific warranty details are not provided, ATE products generally adhere to strict quality control processes to ensure reliability and performance in automotive braking systems.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384230805685,"sku":"CNJW-SP20154","price":74.33,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20154_Fro_59883b64-d256-4e59-af2c-1bdc5f6fa735.jpg?v=1774633359"},{"product_id":"ate-sp20173-disc-brake-rotor","title":"ATE SP20173 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20173\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20173 is designed specifically for Saab 9-3 models, providing reliable braking performance. This vented disc brake rotor features a rust-resistant coating to enhance durability and maintain optimal function over time.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 19.90 mm for consistent braking surface\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring proper fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 292.00 mm matching Saab 9-3 specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.000 mm for precise alignment\u003c\/li\u003e\n\u003cli\u003eRotor Type: Vented to improve heat dissipation during braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetails on the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings that help resist rust and corrosion, extending the service life of the brake components. This product line is engineered to meet the exact specifications of vehicle manufacturers, including the Saab 9-3, ensuring compatibility and reliable braking performance. The SP20173 rotor benefits from this coating technology, maintaining its integrity under various driving conditions.\u003c\/p\u003e\u003ch2\u003eTechnical Description of the SP20173 Rotor\u003c\/h2\u003e\u003cp\u003eThe SP20173 disc brake rotor is constructed from high-quality metal with a full cast design, offering durability and consistent performance. Its vented structure allows for improved heat dissipation, reducing the risk of brake fade during extended use. The nominal thickness of 19.90 mm and an outside diameter of 292.00 mm are tailored to fit Saab 9-3 models precisely. The non-directional disc finish simplifies installation, while the rust-resistant coating helps protect the rotor surface from corrosion, which is critical for maintaining braking efficiency over time.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on Saab 9-3 vehicles\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eHelps reduce brake fade by improving heat dissipation\u003c\/li\u003e\n\u003cli\u003ePrevents rust buildup that can impair braking performance\u003c\/li\u003e\n\u003cli\u003eRestores proper rotor thickness for safe braking operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the ATE Coated Single Pack Rotor SP20173 on a Saab 9-3, ensure the rotor surface is clean and free of debris before mounting. The non-directional finish allows for flexible installation orientation. Verify that the bolt hole diameter of 5 mm matches the vehicle’s hub bolts. It is recommended to replace brake pads simultaneously to ensure even wear and optimal braking performance. Proper torque specifications should be followed to avoid rotor warping.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eATE rotors, including the SP20173, are manufactured to meet strict quality standards and vehicle specifications. The rust-resistant coating is applied to enhance longevity and maintain rotor integrity. While specific warranty details are not provided here, ATE products typically come with manufacturer-backed warranties covering defects in materials and workmanship. Always consult the product documentation or manufacturer for exact warranty terms.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384231035061,"sku":"CNJW-SP20173","price":63.33,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20173_Fro_764d8d7c-7f4d-452f-b628-ad9b3c052cb7.jpg?v=1774633359"},{"product_id":"ate-sp20176-disc-brake-rotor","title":"ATE SP20176 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20176 for Porsche Boxster\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20176 is engineered specifically for Porsche Boxster models, providing reliable braking performance. This disc brake rotor features a vented design and rust-resistant coating to enhance durability and heat dissipation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Porsche Boxster vehicles\u003c\/li\u003e\n\u003cli\u003ePart number SP20176 for precise identification\u003c\/li\u003e\n\u003cli\u003eVented disc brake rotor with full cast construction\u003c\/li\u003e\n\u003cli\u003eRust-resistant coating for extended service life\u003c\/li\u003e\n\u003cli\u003eNon-directional disc finish for versatile installation\u003c\/li\u003e\n\u003cli\u003eNominal thickness of 20.00 mm and outside diameter of 292.00 mm\u003c\/li\u003e\n\u003cli\u003eBolt hole diameter of 5 mm and rotor height of 3.000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Features of the ATE Coated Single Pack Rotor\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line is designed to meet the demands of high-performance braking systems. This rotor, part number SP20176, is constructed from metal with a full cast design, ensuring structural integrity and consistent performance. The vented rotor type improves heat dissipation during braking, reducing the risk of brake fade under heavy use. Its non-directional disc finish allows for flexible installation without concern for rotor orientation. Additionally, the rust-resistant coating protects the rotor surface from corrosion, which is particularly beneficial for vehicles exposed to moisture and road salts.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement rotor for worn or warped brake discs on Porsche Boxster\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise and vibration issues caused by uneven rotor surfaces\u003c\/li\u003e\n\u003cli\u003eImproves heat management to prevent brake fade during aggressive driving\u003c\/li\u003e\n\u003cli\u003ePrevents rust and corrosion that can compromise braking efficiency\u003c\/li\u003e\n\u003cli\u003eRestores braking performance to factory specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Porsche Boxster models before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and hardware for wear and replace if necessary\u003c\/li\u003e\n\u003cli\u003eClean mounting surfaces to ensure proper rotor seating\u003c\/li\u003e\n\u003cli\u003eTorque bolts to manufacturer specifications to avoid rotor warping\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to optimize braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20176 is manufactured to meet OEM standards for fit, form, and function. The rust-resistant coating and full cast construction contribute to the rotor's durability and reliability. While specific warranty details are not provided, ATE products typically adhere to stringent quality controls to ensure consistent performance and safety.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384232083637,"sku":"CNJW-SP20176","price":83.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20176_Fro_e09a4506-8404-460d-bfc6-5ef452283dc1.jpg?v=1774633360"},{"product_id":"ate-sp20183-disc-brake-rotor","title":"ATE SP20183 Disc Brake Rotor - Rear","description":"\u003ch2\u003eOverview of ATE Coated Single Pack Rotor SP20183\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20183 is engineered for reliable braking performance on select BMW models. Designed specifically for BMW 528i, 525i, and 530i vehicles, this vented disc brake rotor offers durability and consistent stopping power.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: Metal construction for strength and heat dissipation\u003c\/li\u003e\n\u003cli\u003eNominal Thickness: 20.00 mm for optimal rotor life\u003c\/li\u003e\n\u003cli\u003eBolt Hole Diameter: 5 mm ensuring precise fitment\u003c\/li\u003e\n\u003cli\u003eDisc Finish: Non-directional for versatile installation\u003c\/li\u003e\n\u003cli\u003eConstruction: Full cast design for structural integrity\u003c\/li\u003e\n\u003cli\u003eRust Resistant Coating: Yes, to reduce corrosion and extend service life\u003c\/li\u003e\n\u003cli\u003eOutside Diameter: 320.00 mm matching OEM specifications\u003c\/li\u003e\n\u003cli\u003eHeight: 2.854 mm for proper caliper clearance\u003c\/li\u003e\n\u003cli\u003eRotor Type: Vented to improve heat dissipation during braking\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the ATE Coated Single Pack Rotor Product Line\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor line focuses on providing rotors with protective coatings to resist rust and corrosion. This coating enhances the rotor's longevity and maintains braking efficiency over time. The SP20183 model benefits from this coating, making it suitable for BMW 528i, 525i, and 530i drivers seeking a reliable replacement rotor that meets factory standards.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe SP20183 disc brake rotor is constructed from high-quality metal with a full cast design, ensuring durability and consistent performance under demanding conditions. Its vented design allows for improved heat dissipation, reducing the risk of brake fade during extended use. The non-directional disc finish simplifies installation, allowing the rotor to be mounted in either orientation without affecting performance. The rust resistant coating protects the rotor surface from corrosion, which is especially beneficial in environments prone to moisture and road salt exposure. With an outside diameter of 320 mm and a nominal thickness of 20 mm, this rotor matches the original equipment specifications for BMW 528i, 525i, and 530i models, ensuring proper fit and function.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for worn or warped rotors on BMW 528i, 525i, and 530i\u003c\/li\u003e\n\u003cli\u003eImproves braking consistency by eliminating rotor surface irregularities\u003c\/li\u003e\n\u003cli\u003eAddresses brake noise caused by uneven rotor wear\u003c\/li\u003e\n\u003cli\u003eHelps reduce brake fade through vented rotor design\u003c\/li\u003e\n\u003cli\u003ePrevents rust-related rotor degradation with protective coating\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with BMW 528i, 525i, and 530i models before installation\u003c\/li\u003e\n\u003cli\u003eInspect brake pads and calipers for wear when replacing rotors\u003c\/li\u003e\n\u003cli\u003eFollow manufacturer torque specifications for bolt installation\u003c\/li\u003e\n\u003cli\u003eClean rotor surface before installation to remove any protective oils\u003c\/li\u003e\n\u003cli\u003ePerform a bed-in procedure after installation to optimize braking performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eThe ATE Coated Single Pack Rotor SP20183 is manufactured to meet strict quality standards, ensuring reliable performance and durability. The rust resistant coating adds an extra layer of protection against environmental factors. Warranty details should be confirmed with the original equipment manufacturer or authorized distributor.\u003c\/p\u003e","brand":"ATE","offers":[{"title":"Default Title","offer_id":43384239292597,"sku":"CNJW-SP20183","price":89.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AE_SP20183_Fro_bb6906e0-7ea2-4392-b7b5-4e6b2becf0f4.jpg?v=1774633360"}],"url":"https:\/\/www.partcatalog.com\/collections\/drums-and-rotors.oembed?page=13","provider":"PartCatalog","version":"1.0","type":"link"}