{"title":"Exhaust \u003e Exhaust and Tail Pipes","description":"\u003cp\u003eExhaust and tail pipes route combustion gases from the catalytic converter or muffler out through the rear (or side) of your vehicle. This collection covers everything in that run — main exhaust pipes, tail pipes, Y-pipes for V-engine configurations, flex connectors, reducers, crossover pipes, and complete system kits. These components fail from the outside in: road salt, moisture, and heat cycling cause rust perforation, typically after 5–10 years depending on climate and material. Aluminized steel is the standard for budget replacements; stainless steel costs more upfront but resists corrosion significantly longer and is worth the premium in rust-belt states. When buying, confirm the pipe's inlet and outlet diameter (commonly 2.0\", 2.25\", or 2.5\"), overall length, and bend configuration — a pipe that's close won't seal. OEM-spec replacements are bolt-on; universal pipes require cutting and clamping. If your vehicle uses a flex connector, replace it separately before it cracks and telegraphs exhaust drone into the cabin.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHissing, ticking, or rumbling exhaust note under acceleration\u003c\/strong\u003e — A perforated or cracked pipe leaks exhaust gas before it exits the system. The noise typically worsens when the engine is cold and may quiet slightly once metal expands at operating temperature.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVisible rust holes, heavy scale, or pipe sections that flex by hand\u003c\/strong\u003e — Surface rust is cosmetic, but once a pipe wall is thin enough to flex or crumble under light pressure, it will perforate shortly. This is especially common on the bend closest to the muffler and at seam welds.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eExhaust smell inside the cabin at idle or with the HVAC on recirculate\u003c\/strong\u003e — A leak upstream of the tail pipe exit can allow CO to enter through the firewall or floor seams. This is a safety issue requiring immediate inspection.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFailed emissions test or stored P0420\/P0430 catalyst codes\u003c\/strong\u003e — Exhaust leaks between the oxygen sensors corrupt fuel trim and air-fuel ratio readings. A leak ahead of the downstream O2 sensor can mimic a failing catalytic converter.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRattling or clunking over bumps that changes with engine RPM\u003c\/strong\u003e — A detached pipe hanger, cracked Y-pipe, or loose connector lets the exhaust system contact the underbody or heat shields, producing metallic noise that's often mistaken for a suspension issue.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHow long do exhaust pipes typically last, and when should I plan for replacement?\u003c\/strong\u003e\n  Aluminized steel pipes last roughly 5–7 years in high-salt climates and 8–12 years in drier regions. Stainless steel can exceed 15 years. Mileage matters less than age and environment — inspect the full pipe run annually if you drive in areas where roads are salted in winter.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eShould I buy OEM or aftermarket, and does the pipe material matter?\u003c\/strong\u003e\n  For daily drivers, a quality aftermarket aluminized pipe from brands like Walker or AP Exhaust fits accurately and costs 40–60% less than OEM. Stainless pipes (Flowmaster, Magnaflow) cost more but eliminate re-replacement in a few years. Avoid unbranded pipes with thin walls — they perforate quickly at bends where heat concentrates.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat does exhaust pipe replacement typically cost, and what else should I replace at the same time?\u003c\/strong\u003e\n  Parts run $30–$150 for individual pipes; complete system kits range $100–$400 depending on vehicle. Labor adds $75–$200 at a shop if fasteners are seized. While the system is apart, replace exhaust clamps, any worn rubber hangers ($3–$8 each), and inspect the flex connector and flange gaskets — they're cheap insurance against doing the job twice.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"ap-exhaust-9822-exhaust-tail-pipe-tip","title":"AP Exhaust 9822 Exhaust Tail Pipe Tip - Left or Right","description":"\u003ch2\u003eChrome Exhaust Tail Pipe Tip for Select Vehicles\u003c\/h2\u003e\u003cp\u003eAP Exhaust 9822 is a bolt-on exhaust tail pipe tip built from aluminized steel with a chrome plated finish. Its round shape and inside roll pencil outlet give the rear of the vehicle a clean, finished look while matching select factory-style exhaust applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAP Exhaust part number 9822\u003c\/li\u003e\n\u003cli\u003eBolt-on attachment type for straightforward tail pipe tip replacement\u003c\/li\u003e\n\u003cli\u003eChrome plated finish for a polished appearance\u003c\/li\u003e\n\u003cli\u003eAluminized steel construction\u003c\/li\u003e\n\u003cli\u003eRound shape with inside roll pencil outlet\u003c\/li\u003e\n\u003cli\u003e1-3\/4\" inlet diameter\u003c\/li\u003e\n\u003cli\u003eOverall size: 5-1\/4\"\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 9822 exhaust tail pipe tip is built for drivers replacing a worn, damaged, or missing chrome tip on select Honda, Nissan, Acura, Subaru, Toyota, Mazda, and other applications. It is listed for a wide range of vehicles including the 2010-2012 Ford Fusion, 2011-2012 Lincoln MKZ, 2010-2011 Mercury Milan, 2003-2004 Honda Pilot, 2001-2003 Acura MDX, and 1992-2001 Honda Prelude. The chrome plated exterior provides a clean finish, while the aluminized steel body supports long-term exhaust use.\u003c\/p\u003e\u003cp\u003eAP Exhaust 9822 is also listed for select Nissan Sentra, Maxima, 300ZX, and 200SX applications, plus several older Honda Accord, Civic, and Toyota Camry and Supra models. For shoppers searching for a chrome exhaust tail pipe tip for 1992-2000 Honda Civic, a bolt-on chrome tip for 1999-2005 Mazda Miata, or a replacement exhaust tip for 1990-1996 Nissan 300ZX left or right position, this part number is a direct fitment match within the listed applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDamaged or corroded exhaust tail pipe tip\u003c\/li\u003e\n\u003cli\u003eMissing chrome tip on a factory-style exhaust outlet\u003c\/li\u003e\n\u003cli\u003eRust-prone appearance at the rear exhaust finish point\u003c\/li\u003e\n\u003cli\u003eWorn exterior trim at the exhaust outlet\u003c\/li\u003e\n\u003cli\u003eNeed for a replacement tip on select left or right rear exhaust positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCompatible With the exact year, make, model, and position listed in the fitment data.\u003c\/li\u003e\n\u003cli\u003eVerify the 1-3\/4\" inlet diameter and overall 5-1\/4\" size before installation.\u003c\/li\u003e\n\u003cli\u003eSome applications note chrome tip usage, optional chrome, or California\/emissions-specific fitment details.\u003c\/li\u003e\n\u003cli\u003eSeveral vehicles list left or right position for the 300ZX; match the side before ordering.\u003c\/li\u003e\n\u003cli\u003eInspect the existing exhaust outlet for proper bolt-on alignment and clearance.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 9822 is manufactured as a chrome plated, aluminized steel exhaust tip for listed OE-style applications. This part cross-references no additional part numbers in the provided data.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385503449269,"sku":"BBDL-9822","price":30.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_9822_Top.jpg?v=1774704107"},{"product_id":"ap-exhaust-9850-exhaust-tail-pipe-tip","title":"AP Exhaust 9850 Exhaust Tail Pipe Tip - Left or Right","description":"\u003ch2\u003eAP Exhaust 9850 Tail Pipe Tip Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 9850 is a stainless steel exhaust tail pipe tip with an oval shape, angled cut tip, and inside roll angle-cut outlet. The tap-on attachment and 2-inch inlet diameter make it a practical replacement for select vehicles that use a clamp-on style tailpipe tip. AP Exhaust 9850 is listed for a wide range of applications, including Toyota Camry, Honda Accord, and Nissan Maxima fitments.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStainless steel construction for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eOval shape with angled cut styling\u003c\/li\u003e\n\u003cli\u003eInside roll angle-cut outlet for a finished exhaust appearance\u003c\/li\u003e\n\u003cli\u003eTap-on attachment type for straightforward tailpipe installation\u003c\/li\u003e\n\u003cli\u003e2-inch inlet diameter\u003c\/li\u003e\n\u003cli\u003eNatural finish\u003c\/li\u003e\n\u003cli\u003eOverall size: 5-1\/16\" x 2-3\/4\" x 3-7\/16\"\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBuilt as an exhaust tail pipe tip, AP Exhaust part number 9850 adds a clean stainless steel finish to the rear of the exhaust system while maintaining an OE-style look on many import and domestic sedans and crossovers. Its oval profile, angled cut tip, and inside roll angle-cut outlet create a refined appearance that works well on vehicles such as the Toyota Camry, Honda Accord, and Nissan Maxima. The natural stainless finish keeps the look understated and factory-appropriate.\u003c\/p\u003e\u003cp\u003eThis part number 9850 is listed across multiple years and positions, including left, right, and N\/A applications depending on the vehicle. It is a fitment-based replacement for drivers looking for an exhaust tail pipe tip that matches the original tailpipe layout on specific models.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2018-2024 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2019-2023 Toyota RAV4, right\u003c\/li\u003e\n\u003cli\u003eFits 2021-2023 Toyota Venza, right\u003c\/li\u003e\n\u003cli\u003eFits 2013-2022 Buick Encore, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2019-2020 Kia Sorento, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2016-2018 Kia Sorento, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2018 Lexus ES350, left\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Buick Verano, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2017 Honda Accord, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Nissan Maxima, left\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Nissan Maxima, left\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Nissan Maxima, right\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Nissan Maxima, right\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Toyota Camry, left\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Toyota Camry, right\u003c\/li\u003e\n\u003cli\u003eFits 2009-2015 Toyota Venza, left\u003c\/li\u003e\n\u003cli\u003eFits 2009-2015 Toyota Venza, right\u003c\/li\u003e\n\u003cli\u003eFits 2009-2015 Toyota Venza, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Nissan Murano, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2012 Honda Accord, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2012 Honda Accord, left\u003c\/li\u003e\n\u003cli\u003eFits 2008-2012 Honda Accord, right\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Lexus ES350, left\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Lexus ES350, right\u003c\/li\u003e\n\u003cli\u003eFits 2005-2012 Toyota Avalon, left\u003c\/li\u003e\n\u003cli\u003eFits 2005-2012 Toyota Avalon, right\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Buick Lucerne, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Honda Civic, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2010-2011 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Toyota Camry, left\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Toyota Camry, right\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Hyundai Azera, left\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Hyundai Azera, right\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Kia Optima, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2010 Kia Sportage, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2010 Scion tC, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1997-2001 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Hyundai Tucson, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Nissan Altima, left\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Nissan Altima, right\u003c\/li\u003e\n\u003cli\u003eFits 2006-2009 Subaru Legacy, left\u003c\/li\u003e\n\u003cli\u003eFits 2006-2009 Subaru Legacy, right\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Acura TL, left\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Acura TL, right\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Hyundai Sonata, left\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Hyundai Sonata, right\u003c\/li\u003e\n\u003cli\u003eFits 2003-2008 Mazda 6, left\u003c\/li\u003e\n\u003cli\u003eFits 2003-2008 Mazda 6, right\u003c\/li\u003e\n\u003cli\u003eFits 1999-2008 Toyota Solara, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Honda Accord, left\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Honda Accord, right\u003c\/li\u003e\n\u003cli\u003eFits 2003-2007 Nissan Murano, left\u003c\/li\u003e\n\u003cli\u003eFits 2003-2007 Nissan Murano, right\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 Chrysler Sebring, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Lexus ES330, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xA, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2006 Toyota Camry, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Honda Accord, left\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Honda Accord, right\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Lexus GS300, left\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Lexus GS300, right\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a damaged or worn exhaust tail pipe tip\u003c\/li\u003e\n\u003cli\u003eRestoring a clean rear-exit exhaust appearance on Toyota Camry and Honda Accord applications\u003c\/li\u003e\n\u003cli\u003eUpdating a corroded stainless or chrome-style tip with a stainless steel replacement\u003c\/li\u003e\n\u003cli\u003eMatching left- or right-side tailpipe tip locations on dual-exit vehicles\u003c\/li\u003e\n\u003cli\u003eCorrecting a missing or deteriorated factory-style exhaust finish piece\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify inlet diameter, outlet style, and vehicle-side position before installation. AP Exhaust 9850 uses a tap-on attachment, so the tailpipe end should be inspected for proper fit and secure engagement. On vehicles noted with welded OE exhaust assemblies, replacement of related parts may be required to complete the repair. Confirm whether your application calls for left, right, or N\/A positioning before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust part number 9850 is built from stainless steel for durable exhaust service and consistent appearance. The part is cataloged for specific year, make, model, and position combinations to support accurate fitment selection for vehicles such as Toyota Camry, Nissan Maxima, and Honda Accord.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385503547573,"sku":"BBDL-9850","price":46.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_9850_Top.jpg?v=1774704107"},{"product_id":"ap-exhaust-14711-exhaust-tail-pipe","title":"AP Exhaust 14711 Exhaust Tail Pipe","description":"\u003ch2\u003eAP Exhaust 14711 Tail Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14711 is an aluminized steel exhaust tail pipe built as an original equipment replacement for select Ford, Mercury, Chevrolet, and Pontiac applications. It is shaped for direct replacement on vehicles with welded OE exhaust assemblies, including common fitments such as Ford Taurus, Mercury Sable, Chevrolet Cavalier, and Pontiac Sunfire.\u003c\/p\u003e\u003cp\u003eUse AP Exhaust 14711 when you need a replacement tail pipe that matches the factory exhaust layout and material style for the listed applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eDirect-fit tail pipe for select OE-style welded exhaust systems\u003c\/li\u003e\n\u003cli\u003eCompatible with single and dual exhaust configurations where listed\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 14711 for factory-style exhaust repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1996-2007 Ford Taurus, N\/A; (Plain Spout); OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; Single Exhaust\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Ford Taurus, N\/A; (Plain Spout); OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; Dual Exhaust\u003c\/li\u003e\n\u003cli\u003eFits 1996-2005 Mercury Sable, N\/A; (Plain Spout); OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; Single Exhaust\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Mercury Sable, N\/A; (Plain Spout); OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; Dual Exhaust\u003c\/li\u003e\n\u003cli\u003eFits 1995-2005 Chevrolet Cavalier, N\/A; OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1998 Pontiac Sunfire, N\/A; (Optional); OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 Pontiac Sunfire, N\/A; OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Pontiac Sunfire, N\/A; OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; Single Exhaust\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Tail Pipe Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorroded or rusted tail pipe sections on factory exhaust systems\u003c\/li\u003e\n\u003cli\u003eCracked or damaged exhaust tubing at the rear of the vehicle\u003c\/li\u003e\n\u003cli\u003eReplacement needs after exhaust repair on welded OE assemblies\u003c\/li\u003e\n\u003cli\u003eRestoration of proper exhaust routing on listed Taurus, Sable, Cavalier, and Sunfire models\u003c\/li\u003e\n\u003cli\u003eService replacement for worn aluminized steel exhaust components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eReview the vehicle-specific notes before ordering, especially the plain spout, optional, single exhaust, and dual exhaust callouts. Because the OE system was a welded assembly on these applications, related exhaust parts noted in the fitment data should be inspected and replaced as needed during repair. AP Exhaust 14711 is referenced for the listed year, make, and model combinations only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14711 is an original equipment replacement tail pipe made from aluminized steel for the specified applications. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385503580341,"sku":"BBDL-14711","price":20.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_14711_Top_6fd6210d-743b-4c95-84a1-403407a44420.jpg?v=1774704107"},{"product_id":"ap-exhaust-14728-exhaust-tail-pipe","title":"AP Exhaust 14728 Exhaust Tail Pipe","description":"\u003ch2\u003eAP Exhaust 14728 Tail Pipe for Chrysler 300M\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14728 is an aluminized steel exhaust tail pipe made as an original equipment replacement for the 1999-2004 Chrysler 300M. It is built for single-exhaust applications and follows the OE system layout used on this vehicle.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system durability\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit service\u003c\/li\u003e\n\u003cli\u003eDesigned for 1999-2004 Chrysler 300M single exhaust applications\u003c\/li\u003e\n\u003cli\u003eTail pipe replacement for OE-style exhaust restoration\u003c\/li\u003e\n\u003cli\u003ePart number 14728 for catalog and fitment reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eCompatible with 1999-2004 Chrysler 300M, N\/A. OE system was a welded assembly, so AP Exhaust 14728 is commonly selected when restoring the rear section of the exhaust on this platform. This part number, 14728, is listed for the Chrysler 300M single exhaust configuration.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust damage in the tail pipe section\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by deterioration in the rear exhaust path\u003c\/li\u003e\n\u003cli\u003eNoise from a damaged or separated tail pipe\u003c\/li\u003e\n\u003cli\u003eLoss of OE exhaust routing on a welded-system Chrysler 300M\u003c\/li\u003e\n\u003cli\u003eReplacement needs during exhaust system repair on 1999-2004 Chrysler 300M models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, make, model, and exhaust configuration before ordering. Because the OE system was a welded assembly, replacement planning may require attention to the full rear exhaust section noted for the application. Confirm alignment and hanger placement during installation to maintain proper exhaust routing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14728 is an OE replacement exhaust tail pipe built to match the application requirements for the Chrysler 300M platform. Aluminized steel construction supports long-term service in a standard exhaust repair environment.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385503645877,"sku":"BBDL-14728","price":20.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_14728_Top.jpg?v=1774704107"},{"product_id":"ap-exhaust-14731-exhaust-tail-pipe","title":"AP Exhaust 14731 Exhaust Tail Pipe","description":"\u003ch2\u003eOE Replacement Tail Pipe for Buick and Pontiac\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14731 is an aluminized steel exhaust tail pipe built as an original equipment replacement for select 2000-2005 Buick LeSabre and Pontiac Bonneville applications. It is shaped for single-exhaust systems and follows the OE-style replacement approach for vehicles that used a welded factory assembly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit repair work\u003c\/li\u003e\n\u003cli\u003eDesigned for single exhaust configurations\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Buick LeSabre, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Pontiac Bonneville, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust tail pipe is intended for drivers replacing a worn, rusted, or damaged rear exhaust section on a 2000-2005 Buick LeSabre or 2000-2005 Pontiac Bonneville. Part number 14731 is built to match OE replacement needs where the factory system was originally a welded assembly, and the notes indicate that related parts marked [1] should be replaced together when servicing the system.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust-through in the rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a damaged tail pipe section\u003c\/li\u003e\n\u003cli\u003eBroken or weakened welded factory exhaust assembly\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust routing on single-exhaust vehicles\u003c\/li\u003e\n\u003cli\u003eReplacing a failed OE-style rear exhaust component\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, make, model, and single-exhaust configuration before installation. Because the OE system was a welded assembly, inspect the adjoining exhaust sections and replace any related parts noted [1] during the repair. Confirm alignment and hanger positioning during installation to ensure proper exhaust routing and clearance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 14731 is an OE replacement exhaust tail pipe made from aluminized steel for service on the listed Buick and Pontiac applications. Part number 14731 is specified for 2000-2005 Buick LeSabre and 2000-2005 Pontiac Bonneville vehicles with single exhaust.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385503776949,"sku":"BBDL-14731","price":35.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_14731_Top_1bf9ee62-00bb-464a-9c05-e2056b814682.jpg?v=1774704108"},{"product_id":"ap-exhaust-18094-exhaust-pipe","title":"AP Exhaust 18094 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18094 Center Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust part number 18094 is an original equipment replacement exhaust pipe made from aluminized steel. It is built for center exhaust routing on select Chrysler, Dodge, Plymouth, and Ram applications, including Chrysler Town \u0026amp; Country, Dodge Grand Caravan, and Dodge Ram 2500\/3500 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit service on listed applications\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe position\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for welded factory exhaust assemblies where noted\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 18094 for select Chrysler, Dodge, Plymouth, and Ram vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18094 is a center exhaust pipe engineered as an OE replacement for a wide range of minivan and truck applications. It is listed for 1991-2005 Chrysler Town \u0026amp; Country, Dodge Grand Caravan, Grand Voyager, Caravan, Plymouth Grand Voyager, Plymouth Voyager, and select Dodge Ram 2500 and Ram 3500 models. For many of these vehicles, the factory exhaust system was a welded assembly, so replacement planning should account for the related exhaust sections called out in the fitment notes. The aluminized steel construction supports long-term exhaust service in a direct replacement format.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1996-2005 Chrysler Town \u0026amp; Country, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1996-2005 Dodge Grand Caravan, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 2000 Chrysler Grand Voyager, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Plymouth Grand Voyager, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1996-1997 Dodge Caravan, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1997 Dodge Ram 2500, Center. (2 used); Cut as required.; over 8800 lbs. G.V.W.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1997 Dodge Ram 3500, Center. (2 used); Cut as required.; over 8800 lbs. G.V.W.\u003c\/li\u003e\n\u003cli\u003eFits 1996 Plymouth Voyager, Center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1995 Chrysler Town \u0026amp; Country, Center.\u003c\/li\u003e\n\u003cli\u003eFits 1991-1995 Dodge Grand Caravan, Center.\u003c\/li\u003e\n\u003cli\u003eFits 1991-1995 Plymouth Grand Voyager, Center.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for a rusted or perforated center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eService part for a leaking welded factory exhaust section\u003c\/li\u003e\n\u003cli\u003eRepair for exhaust noise caused by cracks or separation in the center pipe\u003c\/li\u003e\n\u003cli\u003eDirect replacement for damaged OE exhaust routing on Chrysler, Dodge, and Plymouth vans\u003c\/li\u003e\n\u003cli\u003eCenter section repair on heavy-duty Dodge Ram 2500 and Ram 3500 exhaust systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and center exhaust position before ordering. On applications noted as welded OE systems, inspect the adjoining exhaust sections and replace the related parts identified in the fitment notes as needed. For 1995-1997 Dodge Ram 2500 and Ram 3500 applications over 8800 lbs. G.V.W., the notes specify cut-to-fit installation and use on vehicles where two pipes are used.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures OE replacement exhaust components for service applications that require factory-style fitment and material selection. Part number 18094 is built as an aluminized steel replacement for the listed center exhaust applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504006325,"sku":"BBDL-18094","price":22.15,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18094_Top.jpg?v=1774704108"},{"product_id":"ap-exhaust-18122-exhaust-pipe","title":"AP Exhaust 18122 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18122 Exhaust Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18122 is an aluminized steel exhaust pipe built as an original equipment replacement for specific Chrysler, Dodge, and Dodge Dakota applications. It is listed for center-position use and matches OE-style fitment for vehicles that used a welded exhaust assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eCenter-position exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for selected Chrysler Town \u0026amp; Country, Dodge Grand Caravan, and Dodge Dakota models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 18122 for direct catalog identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 18122 exhaust pipe is intended for drivers replacing a center exhaust section on select 2001-2005 Chrysler Town \u0026amp; Country and Dodge Grand Caravan models, as well as 1997-1999 Dodge Dakota 4WD applications with a 131-inch wheelbase. The aluminized steel construction supports routine exhaust system replacement needs, while the OE replacement design follows the original system layout for a proper service match. For Chrysler Town \u0026amp; Country and Dodge Grand Caravan applications, the OE system was a welded assembly, so related parts noted in the vehicle listing should be evaluated together during repair planning. AP Exhaust 18122 is a practical choice when servicing a center exhaust pipe on these specific vehicles.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2001-2005 Chrysler Town \u0026amp; Country, center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; except \"Stow and Go\" Option\u003c\/li\u003e\n\u003cli\u003eFits 2001-2005 Dodge Grand Caravan, center. OE system was a welded assembly. It is recommended that all parts noted [1] should be replaced.; except \"Stow and Go\" Option\u003c\/li\u003e\n\u003cli\u003eFits 1997-1999 Dodge Dakota, center. (131\" W.B., 4 W.D.)\u003c\/li\u003e\n\u003cli\u003eFits 1997-1999 Dodge Dakota, center. (131\" W.B., 4WD)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement for a rusted or corroded center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eService part for a damaged welded exhaust section\u003c\/li\u003e\n\u003cli\u003eRepair for exhaust leaks at the center section\u003c\/li\u003e\n\u003cli\u003eRestoration of proper exhaust routing on listed Chrysler and Dodge vehicles\u003c\/li\u003e\n\u003cli\u003eDirect replacement for worn OE exhaust pipe assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle’s year, make, model, and center-position exhaust configuration before ordering. On 2001-2005 Chrysler Town \u0026amp; Country and Dodge Grand Caravan models, verify whether the vehicle is equipped with the Stow and Go option, since that application is excluded. For the welded OE exhaust assemblies, inspect related sections of the system before installation so the replacement pipe matches the condition of the surrounding components.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement exhaust pipe made from aluminized steel. Part number 18122 is cataloged for the listed Chrysler, Dodge, and Dodge Dakota applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504039093,"sku":"BBDL-18122","price":22.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18122_Top_f57804c3-78d6-488d-b65b-0e309205d5ef.jpg?v=1774704109"},{"product_id":"ap-exhaust-18123-exhaust-pipe","title":"AP Exhaust 18123 Exhaust Pipe - Center","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for GM Vans\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18123 is an aluminized steel exhaust pipe built as an original equipment replacement for select GM minivans. It is made for the center section of the exhaust system on 1997-2001 Oldsmobile Silhouette, 1999-2001 Pontiac Montana, and 1997-1998 Pontiac Trans Sport applications with the UM code.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in everyday exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit service on the listed applications\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe location for the factory exhaust layout\u003c\/li\u003e\n\u003cli\u003eFits 1997-2001 Oldsmobile Silhouette, center\u003c\/li\u003e\n\u003cli\u003eFits 1999-2001 Pontiac Montana, center\u003c\/li\u003e\n\u003cli\u003eFits 1997-1998 Pontiac Trans Sport, center\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 18123 for OE-style exhaust repair on compatible GM vans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is intended for vehicles with the welded OE system noted in the fitment data. For the Oldsmobile Silhouette, Pontiac Montana, and Pontiac Trans Sport, the center section is part of the factory exhaust routing and should be matched to the vehicle’s code UM configuration. AP Exhaust 18123 is a practical replacement when servicing the center exhaust pipe on these models.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Repair\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRusted or perforated center exhaust pipe sections\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a damaged welded assembly\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust operation caused by a failing pipe section\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow from corrosion or structural damage\u003c\/li\u003e\n\u003cli\u003eFactory exhaust fitment issues on UM-code GM minivans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s door decal code UM before ordering. The OE system was a welded assembly, so AP Exhaust recommends replacing all parts identified in the fitment notes during service. Confirm the center position and compare the existing exhaust routing before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18123 is an original equipment replacement part made from aluminized steel for service on the listed Oldsmobile and Pontiac applications. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504071861,"sku":"BBDL-18123","price":27.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18123_Top_df16b18c-20ee-487c-90c5-d5d3a53349e3.jpg?v=1774704109"},{"product_id":"ap-exhaust-18135-exhaust-pipe","title":"AP Exhaust 18135 Exhaust Pipe - Front","description":"\u003ch2\u003eAP Exhaust 18135 Exhaust Pipe for Ford Focus\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18135 is an aluminized steel exhaust pipe built as an original equipment replacement for the front exhaust section on select Ford Focus models. It is a direct-fit option for 2000-2004 Ford Focus, front, with the SPI Engine (Engine Code P), and it supports a factory-style exhaust repair on the Ford Focus platform.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement for factory-style fit and routing\u003c\/li\u003e\n\u003cli\u003eFront exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2000-2004 Ford Focus, front, SPI Engine (Engine Code P)\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 18135\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is intended for drivers replacing a worn, rusted, or damaged front pipe on a 2000-2004 Ford Focus with the SPI engine. AP Exhaust 18135 follows OE replacement specifications, making it a practical choice when restoring exhaust flow and maintaining the original exhaust layout. The aluminized steel material adds durability for everyday street use while keeping the part aligned with factory-style service requirements. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a corroded front exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks at the front section\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust routing on a Ford Focus\u003c\/li\u003e\n\u003cli\u003eAddressing noise caused by a damaged pipe section\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to OE-style configuration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify engine code P before ordering, since this AP Exhaust 18135 pipe is listed for SPI Engine applications only. Confirm the front exhaust routing and compare the existing pipe shape, hanger locations, and connection points before installation. Professional exhaust installation is recommended to ensure proper alignment and sealing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures replacement exhaust components to OE-style specifications for service and repair applications. Part number 18135 is built as an original equipment replacement using aluminized steel for dependable exhaust system service.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504170165,"sku":"BBDL-18135","price":93.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18135_Top.jpg?v=1774704109"},{"product_id":"ap-exhaust-18167-exhaust-pipe","title":"AP Exhaust 18167 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18167 Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18167 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford and Mercury applications. It is listed for center-position fitment on 2002-2005 Ford Explorer and 2002-2005 Mercury Mountaineer, making it a direct-match option for OE-style exhaust repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2002-2005 Ford Explorer, center\u003c\/li\u003e\n\u003cli\u003eFits 2002-2005 Mercury Mountaineer, center\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 18167\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is intended for vehicles that need a center-section replacement in the exhaust system. AP Exhaust 18167 follows OE replacement specifications and uses aluminized steel, a common exhaust material chosen for service life in everyday driving conditions. For buyers searching for a 2002-2005 Ford Explorer center exhaust pipe or a 2002-2005 Mercury Mountaineer center exhaust pipe, this part number 18167 matches the listed applications directly.\u003c\/p\u003e\u003cp\u003eThe OE system note for the Ford Explorer indicates the original assembly was welded, and AP Exhaust recommends replacing all parts noted in that system when servicing the vehicle. That makes this part a practical choice when restoring the center section of the exhaust on the Explorer or Mountaineer platform.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDamaged or rusted center exhaust pipe sections\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a corroded OE pipe\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust caused by a failing center section\u003c\/li\u003e\n\u003cli\u003eFitment issues when replacing a welded factory assembly\u003c\/li\u003e\n\u003cli\u003eRestoration of the exhaust path on listed Ford and Mercury SUVs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, make, model, and center-position application before installation. On 2002-2005 Ford Explorer models, the OE system was a welded assembly, so related exhaust components noted in the system should be inspected and replaced as needed during service. Confirm alignment and sealing surfaces before final tightening.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18167 is an OE replacement exhaust pipe built from aluminized steel for the listed applications. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504202933,"sku":"BBDL-18167","price":31.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18167_Top.jpg?v=1774704109"},{"product_id":"ap-exhaust-18169-exhaust-pipe","title":"AP Exhaust 18169 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18169 Exhaust Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18169 is an aluminized steel exhaust pipe made as an original equipment replacement for select GM and Isuzu applications. It is built for vehicles with a welded OE exhaust assembly, making it a direct-fit service part for restoring the exhaust path on compatible models.\u003c\/p\u003e\u003cp\u003eCompatible with 2002-2005 Chevrolet Trailblazer, center; 2002-2005 GMC Envoy, center; 2002-2004 Oldsmobile Bravada, center; 2004-2005 Buick Rainier, center; and 2003-2005 Isuzu Ascender, N\/A. AP Exhaust 18169 is a practical replacement when servicing the center exhaust section on these vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit applications\u003c\/li\u003e\n\u003cli\u003eBuilt for center exhaust placement on listed vehicles\u003c\/li\u003e\n\u003cli\u003eSuitable for OE systems that were originally welded assemblies\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 18169 supports service replacement on select Chevrolet Trailblazer, GMC Envoy, Buick Rainier, Oldsmobile Bravada, and Isuzu Ascender models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is engineered for OE-style replacement on vehicles that left the factory with a welded exhaust assembly. The aluminized steel construction provides a durable service part for exhaust repair, while the direct replacement format helps maintain the original routing and fitment expected for the application. AP Exhaust 18169 is a focused solution for center exhaust repair on the listed GM and Isuzu platforms.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or damaged center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after a welded OE section fails\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks at the center section\u003c\/li\u003e\n\u003cli\u003eServicing a Trailblazer, Envoy, Rainier, Bravada, or Ascender exhaust system\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust path to OE-style routing on listed applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2004-2005 Buick Rainier, center. Fits 2002-2005 Chevrolet Trailblazer, center. Fits 2002-2005 GMC Envoy, center. Fits 2003-2005 Isuzu Ascender, N\/A. Fits 2002-2004 Oldsmobile Bravada, center. Because the OE system was a welded assembly, AP Exhaust recommends replacing all parts noted [1] during service. Verify the vehicle’s wheelbase and exhaust configuration before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies OE replacement exhaust components for service applications, and this part is built to match the listed fitment and material requirements for the specified vehicles.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504301237,"sku":"BBDL-18169","price":43.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18169_Top.jpg?v=1774704110"},{"product_id":"ap-exhaust-18180-exhaust-pipe","title":"AP Exhaust 18180 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18180 Exhaust Pipe for Explorer Sport\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18180 is an aluminized steel exhaust pipe made as an original equipment replacement for the center exhaust routing on select Ford Explorer Sport models. It is built for 2001-2003 Ford Explorer Sport applications with the OE welded-assembly layout noted in the fitment data.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system replacement service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application for select Ford Explorer Sport models\u003c\/li\u003e\n\u003cli\u003eFits 2001-2003 Ford Explorer Sport, center\u003c\/li\u003e\n\u003cli\u003ePart number 18180 for catalog and service reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is intended for drivers replacing a center section on a Ford Explorer Sport exhaust system. The aluminized steel material provides a service-ready replacement option for corrosion-prone exhaust routing, while the OE replacement design supports factory-style fitment on the specified 2001, 2002, and 2003 Ford Explorer Sport applications. AP Exhaust 18180 is listed for the center position and matches the OE welded-assembly configuration noted for these vehicles.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed interchange numbers in the provided data. For search relevance, this exhaust pipe is a direct-fit replacement for Ford Explorer Sport center exhaust pipe service and Ford Explorer Sport exhaust system repair.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a damaged or rusted center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after corrosion or cracking\u003c\/li\u003e\n\u003cli\u003eRepairing a factory welded-assembly exhaust section\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks at the center pipe section\u003c\/li\u003e\n\u003cli\u003eReturning a Ford Explorer Sport exhaust system to OE-style routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2001 Ford Explorer Sport, center. Fits 2002 Ford Explorer Sport, center. Fits 2003 Ford Explorer Sport, center. Review the OE welded-assembly note before installation, and verify the vehicle build date and exhaust configuration against the fitment notes. The catalog data recommends replacing all parts noted in the OE system when servicing this application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18180 is an original equipment replacement exhaust pipe built from aluminized steel for the listed Ford Explorer Sport applications. Confirm fitment by year, model, position, and build-date notes before installation.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504334005,"sku":"BBDL-18180","price":19.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18180_Top.jpg?v=1774704110"},{"product_id":"ap-exhaust-18192-exhaust-pipe","title":"AP Exhaust 18192 Exhaust Pipe - Rear Right","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Silverado and Sierra\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18192 is an aluminized steel exhaust pipe built as an original equipment replacement for select rear right applications. It is engineered for 2001-2006 Chevrolet Silverado 2500 HD and 2001-2006 GMC Sierra 2500 HD models with a 143.5-inch wheelbase and OE welded exhaust system configuration.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit service on listed applications\u003c\/li\u003e\n\u003cli\u003eRear right exhaust pipe location\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 Chevrolet Silverado 2500 HD, rear right\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 GMC Sierra 2500 HD, rear right\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment and Application Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 18192 exhaust pipe is used on rear right exhaust routing for the listed heavy-duty trucks. It cross-references OE part number 15798948 for the same application. Use it for 2001-2006 Chevrolet Silverado 2500 HD and 2001-2006 GMC Sierra 2500 HD models with the 143.5-inch wheelbase and welded OE exhaust system layout.\u003c\/p\u003e\u003ch2\u003eCommon Exhaust Issues It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust or corrosion in the rear right exhaust pipe\u003c\/li\u003e\n\u003cli\u003eCracks or leaks in the original welded pipe section\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow from a damaged pipe\u003c\/li\u003e\n\u003cli\u003eNoise from a failing exhaust section\u003c\/li\u003e\n\u003cli\u003eReplacement needs after OE pipe deterioration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify wheelbase, position, and OE exhaust configuration before installation. This application notes that the original system was a welded assembly, and parts identified for the system should be replaced as specified for proper service alignment. Confirm the rear right routing matches the vehicle before ordering AP Exhaust 18192.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust lists this part as an original equipment replacement, and the aluminized steel construction supports exhaust-system durability in the specified application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504399541,"sku":"BBDL-18192","price":20.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18192_Top.jpg?v=1774704110"},{"product_id":"ap-exhaust-18194-exhaust-pipe","title":"AP Exhaust 18194 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 18194 Exhaust Pipe for OE Replacement\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18194 is an aluminized steel exhaust pipe built as an original equipment replacement for select GM midsize SUVs. It is engineered for center exhaust routing and matches applications where the factory exhaust system was originally a welded assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOE replacement design for factory-style fit and routing\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Chevrolet Trailblazer, GMC Envoy, Isuzu Ascender, and Buick Rainier models\u003c\/li\u003e\n\u003cli\u003eCross-reference: this part cross-references GM 25887919 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18194 is a replacement exhaust pipe for 2006-2009 Chevrolet Trailblazer, 2006-2009 GMC Envoy, 2006-2008 Isuzu Ascender, and 2006-2007 Buick Rainier with standard wheelbase configurations. The aluminized steel construction is selected for exhaust-system durability, while the OE replacement format supports factory-style alignment in the center section of the system. AP Exhaust 18194 is a practical choice when servicing a welded OE exhaust assembly on these vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust-through or corrosion in the center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eCracks or leaks in a welded factory exhaust assembly\u003c\/li\u003e\n\u003cli\u003eExhaust noise caused by a damaged pipe section\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow from a deteriorated pipe\u003c\/li\u003e\n\u003cli\u003eFitment issues when replacing an OE-style center exhaust pipe\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2006-2009 Chevrolet Trailblazer, center; 2006-2009 GMC Envoy, center; 2006-2008 Isuzu Ascender, center; and 2006-2007 Buick Rainier, center. These applications note that the OE system was a welded assembly, and it is recommended that all parts noted [1] be replaced during service. Verify standard wheelbase fitment before installation and compare the existing exhaust routing to the replacement pipe.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18194 is built as an OE replacement exhaust pipe using aluminized steel for service in factory-style exhaust repairs.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385504989365,"sku":"BBDL-18194","price":66.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18194_Fro_e7a629e3-b174-4d55-b578-29300664cf99.jpg?v=1774704111"},{"product_id":"ap-exhaust-18196-exhaust-pipe","title":"AP Exhaust 18196 Exhaust Pipe","description":"\u003ch2\u003eAP Exhaust 18196 Exhaust Pipe for Ford E-Series\u003c\/h2\u003e\u003cp\u003eAP Exhaust 18196 is an OE replacement exhaust pipe built for select Ford E-250 and Ford E-350 Super Duty applications. Made from aluminized steel, it is specified for direct-fit exhaust service where corrosion resistance and factory-style routing matter.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system durability\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style service\u003c\/li\u003e\n\u003cli\u003eDirect-fit exhaust pipe for select Ford E-Series vans and chassis applications\u003c\/li\u003e\n\u003cli\u003eCross-references Ford OE part numbers 8C2Z5202A and 9C2Z5A212A\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 18196 for catalog and service identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is engineered for Ford E-250 and Ford E-350 Super Duty models that need a replacement exhaust section matching OE layout and fitment. The aluminized steel construction is suited for exhaust environments where heat and road exposure are constant, and the OE replacement designation supports factory-style service on the Ford E-Series platform. Use AP Exhaust 18196 when replacing a worn, rusted, or damaged exhaust pipe on 2004-2013 Ford E-250 and 2004-2009 Ford E-350 Super Duty applications listed below.\u003c\/p\u003e\u003cp\u003eFits 2009-2013 Ford E-250, N\/A. Fits 2009 Ford E-350 Super Duty, N\/A. Fits 2004 Ford E-350 Super Duty, N\/A. Fits 2008 Ford E-350 Super Duty, N\/A. Fits 2007 Ford E-350 Super Duty, N\/A. Fits 2005-2006 Ford E-350 Super Duty, N\/A.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eExhaust pipe corrosion and rust-through\u003c\/li\u003e\n\u003cli\u003eBroken or damaged exhaust routing on Ford E-Series vans\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by a failing pipe section\u003c\/li\u003e\n\u003cli\u003eFactory-fit replacement needs for service repairs\u003c\/li\u003e\n\u003cli\u003eNoise and vibration from a compromised exhaust path\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify year, model, and configuration before ordering, especially for Ford E-350 Super Duty cutaway and stripped chassis applications with date-specific notes. Confirm the existing exhaust routing and OE part number match the vehicle application before installation. Professional exhaust service practices are recommended for proper alignment and sealing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies OE replacement exhaust components built to match factory service requirements for the listed Ford E-Series applications. This part cross-references Ford OE numbers 8C2Z5202A and 9C2Z5A212A for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505087669,"sku":"BBDL-18196","price":22.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_18196_Top.jpg?v=1774704111"},{"product_id":"ap-exhaust-24629-exhaust-pipe","title":"AP Exhaust 24629 Exhaust Pipe - Center, Front or Rear","description":"\u003ch2\u003eAP Exhaust 24629 Exhaust Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24629 is an aluminized steel exhaust pipe built as an original equipment replacement for a wide range of Ford truck and van applications. It is listed for multiple center, rear, and front positions across Ford F-100, F-150, F-250, and F-350 models, along with select Chevrolet and GMC van fitments.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a Ford F-150 exhaust pipe, Ford F-250 exhaust pipe, or AP Exhaust 24629 replacement pipe, this part is cataloged for direct vehicle-specific applications rather than universal use.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for OE-style exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eCataloged for center, rear, front, and N\/A positions depending on application\u003c\/li\u003e\n\u003cli\u003eFits multiple Ford truck configurations from 1979-1996\u003c\/li\u003e\n\u003cli\u003eAlso listed for select Chevrolet G-series and GMC G-series vans\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 24629\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24629 is an OE replacement exhaust pipe designed for vehicles that used factory exhaust assemblies in welded sections. The aluminized steel construction supports replacement of rusted or damaged exhaust routing on older Ford trucks, including F-100, F-150, F-250, and F-350 models. It is also cataloged for select Chevrolet G10, G20, G30, GMC G1500, G2500, and G3500 van applications with 96.0-inch wide van, hi-cube body fitments.\u003c\/p\u003e\u003cp\u003eThis part number is commonly searched as AP Exhaust 24629 for Ford F-150 and Ford F-250 exhaust repair work where the original system was built as a welded assembly. Fitment varies by year, wheelbase, converter configuration, and exhaust position, so the vehicle notes should be matched carefully before ordering.\u003c\/p\u003e\u003ch2\u003eWhat This Exhaust Pipe Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust-through in the factory exhaust pipe\u003c\/li\u003e\n\u003cli\u003eCracked or damaged exhaust routing on older Ford trucks\u003c\/li\u003e\n\u003cli\u003eReplacement needs after removal of a welded OE exhaust section\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by deteriorated pipe sections\u003c\/li\u003e\n\u003cli\u003eRestoration of factory-style exhaust routing on listed applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1987-1996 Ford F-150, center, including 133\" wheelbase applications with notes for welded OE systems.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1996 Ford F-150, rear, with OE welded-system notes.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1996 Ford F-250, center or rear, with application notes for welded OE systems and select GVW\/converter configurations.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1996 Ford F-350, center, with welded-system notes on select applications.\u003c\/li\u003e\n\u003cli\u003eFits 1979-1986 Ford F-100, F-150, F-250, and F-350 applications in front, center, or rear positions depending on year and converter setup.\u003c\/li\u003e\n\u003cli\u003eFits 1979-1981 Chevrolet G10, G20, G30 and GMC G1500, G2500, G3500 van applications with 96.0\" wide van, hi-cube body notes.\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eBecause many listed vehicles used welded factory exhaust assemblies, related exhaust sections may need to be replaced together for proper alignment. Verify wheelbase, converter presence, GVW notes, and exhaust position before installation. AP Exhaust 24629 is also listed for 1980-1982 Ford F-250 center applications and 1980-1986 Ford F-150 rear applications with converter-specific notes.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust catalogs this part as an original equipment replacement, and the aluminized steel material is selected for service in exhaust-system applications where factory-style fit and corrosion resistance are important. This part number is AP Exhaust 24629.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505349813,"sku":"BBDL-24629","price":20.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_24629_Top_f2800965-b34c-4646-81f0-39c6f4f85535.jpg?v=1774704112"},{"product_id":"ap-exhaust-24885-exhaust-tail-pipe","title":"AP Exhaust 24885 Exhaust Tail Pipe - Right","description":"\u003ch2\u003eAP Exhaust 24885 Tail Pipe for Camaro and Firebird\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24885 is an aluminized steel exhaust tail pipe built as an original equipment replacement for select Chevrolet Camaro and Pontiac Firebird applications. It is listed for the right side and follows OE-style fitment for vehicles with welded factory exhaust assemblies.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eRight-side tail pipe application\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for welded factory exhaust systems\u003c\/li\u003e\n\u003cli\u003ePart number 24885 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust tail pipe is designed for 1993-2002 Chevrolet Camaro and Pontiac Firebird models in right-side applications, including 1995-1997 Camaro, 1993-1995 Firebird, 1996-1997 Firebird, and 1998-2002 Camaro and Firebird configurations. The aluminized steel construction provides a practical replacement option for restoring the exhaust path on vehicles that originally used a welded assembly. AP Exhaust 24885 is a direct-fit style replacement for owners servicing Camaro and Firebird exhaust systems.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed interchange numbers for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or deterioration in the right-side tail pipe\u003c\/li\u003e\n\u003cli\u003eDamage from road debris or exhaust system wear\u003c\/li\u003e\n\u003cli\u003eFactory exhaust replacement on welded OE assemblies\u003c\/li\u003e\n\u003cli\u003eRestoration of proper exhaust routing on Camaro and Firebird models\u003c\/li\u003e\n\u003cli\u003eReplacement of a failed or rusted rear exhaust section\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1998-2002 Chevrolet Camaro, right; OE system was a welded assembly and OE spouts are to be re-used for this application.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2002 Pontiac Firebird, right; OE system was a welded assembly and OE spouts are to be re-used for this application.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1997 Chevrolet Camaro, right; OE system was a welded assembly and dual exhaust is noted.\u003c\/li\u003e\n\u003cli\u003eFits 1996-1997 Pontiac Firebird, right; OE system was a welded assembly and dual exhaust is noted.\u003c\/li\u003e\n\u003cli\u003eFits 1993-1994 Pontiac Firebird, right; OE system was a welded assembly.\u003c\/li\u003e\n\u003cli\u003eFits 1995 Pontiac Firebird, right; OE system was a welded assembly, except California and California only applications are both listed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement, and the aluminized steel construction supports standard exhaust service requirements for the listed Camaro and Firebird applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505382581,"sku":"BBDL-24885","price":27.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_24885_Top.jpg?v=1774704112"},{"product_id":"ap-exhaust-24911-exhaust-tail-pipe","title":"AP Exhaust 24911 Exhaust Tail Pipe","description":"\u003ch2\u003eAP Exhaust 24911 Tail Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24911 is an aluminized steel exhaust tail pipe built as an original equipment replacement for select GM full-size sedans. It is engineered for direct-fit service on 1996-1999 Buick LeSabre, 1996-1999 Oldsmobile 88, 1996-1999 Oldsmobile LSS, 1997-1998 Oldsmobile Regency, 1996 Oldsmobile 98, and 1996-1999 Pontiac Bonneville applications.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a 1996-1999 Buick LeSabre exhaust tail pipe or an AP Exhaust 24911 replacement tail pipe, this part supports OE-style service on vehicles that used a welded factory exhaust assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system replacement service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eDirect application coverage for select Buick, Oldsmobile, and Pontiac models\u003c\/li\u003e\n\u003cli\u003eDesigned for rear exhaust routing in tail pipe applications\u003c\/li\u003e\n\u003cli\u003ePart number 24911 for catalog and fitment lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24911 is a replacement exhaust tail pipe made from aluminized steel, a common material choice for exhaust service because it balances corrosion resistance and durability in everyday driving conditions. As an original equipment replacement, it is intended to match the factory exhaust layout on supported vehicles, including the Buick LeSabre, Oldsmobile 88, Oldsmobile LSS, Oldsmobile Regency, Oldsmobile 98, and Pontiac Bonneville. This part number 24911 is a practical choice when restoring the rear section of the exhaust system on 1996-1999 GM sedans with OE welded assemblies.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust-through or corrosion in the rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by a damaged tail pipe section\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust flow from a compromised rear pipe\u003c\/li\u003e\n\u003cli\u003eFactory exhaust replacement needs after welded-system wear\u003c\/li\u003e\n\u003cli\u003eRestoration of proper exhaust routing on supported GM sedans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1996-1999 Buick LeSabre, N\/A; OE system was a welded assembly, and it is recommended that all parts noted [1] should be replaced. Fits 1996-1999 Oldsmobile 88, N\/A. Fits 1996-1999 Oldsmobile LSS, N\/A; OE system was a welded assembly, and it is recommended that all parts noted [1] should be replaced. Fits 1997-1998 Oldsmobile Regency, N\/A; OE system was a welded assembly, and it is recommended that all parts noted [1] should be replaced. Fits 1996 Oldsmobile 98, N\/A. Fits 1996-1999 Pontiac Bonneville, N\/A; OE system was a welded assembly, and it is recommended that all parts noted [1] should be replaced.\u003c\/p\u003e\u003cp\u003eVerify the vehicle year, make, and model before ordering. Because several listed applications used a welded factory exhaust system, inspect adjoining exhaust components for wear before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies replacement exhaust components for OE-style service, and part 24911 is specified as an original equipment replacement in aluminized steel for the listed applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505546421,"sku":"BBDL-24911","price":46.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_24911_Top_620e1ac0-cb95-4112-86b4-b0d5c07a0e92.jpg?v=1774704113"},{"product_id":"ap-exhaust-24915-exhaust-tail-pipe","title":"AP Exhaust 24915 Exhaust Tail Pipe","description":"\u003ch2\u003eAP Exhaust 24915 Tail Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24915 is an aluminized steel exhaust tail pipe made as an original equipment replacement for select Buick Park Avenue applications. It is built for 1997-2005 Buick Park Avenue models and follows the OE system layout noted for this vehicle line.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a Buick Park Avenue exhaust tail pipe, AP Exhaust 24915 provides a direct-fit replacement option for the factory tail pipe section.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eFits 1997-2005 Buick Park Avenue\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 24915\u003c\/li\u003e\n\u003cli\u003eBuilt for the tail pipe section of the exhaust system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24915 is an OE replacement tail pipe for the Buick Park Avenue, covering model years 1997 through 2005. The aluminized steel material is commonly used in exhaust service parts because it offers a practical balance of corrosion resistance and durability for replacement applications. This part number, 24915, is intended for vehicles using the factory exhaust layout described in the fitment notes, where the OE system was a welded assembly.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRusted or perforated tail pipe sections\u003c\/li\u003e\n\u003cli\u003eExhaust leaks at the rear section of the system\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust caused by damaged pipe walls or failed joints\u003c\/li\u003e\n\u003cli\u003eReplacement needs after corrosion-related exhaust inspection failures\u003c\/li\u003e\n\u003cli\u003eRestoration of factory-style exhaust routing on a Buick Park Avenue\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1997-2005 Buick Park Avenue, N\/A. The fitment notes state that the OE system was a welded assembly, and it is recommended that all parts noted [1] should be replaced. Verify the existing exhaust configuration before installation to confirm the correct replacement path for AP Exhaust 24915.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24915 is an original equipment replacement exhaust tail pipe built to match the factory application for the listed Buick Park Avenue years. The aluminized steel construction supports standard exhaust service replacement needs for this vehicle platform.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505710261,"sku":"BBDL-24915","price":23.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_24915_Top.jpg?v=1774704114"},{"product_id":"ap-exhaust-24920-exhaust-tail-pipe","title":"AP Exhaust 24920 Exhaust Tail Pipe - Left","description":"\u003ch2\u003eAP Exhaust 24920 Left Tail Pipe for Sebring\u003c\/h2\u003e\u003cp\u003eAP Exhaust 24920 is an aluminized steel exhaust tail pipe made as an original equipment replacement for the left side of select Chrysler Sebring models. It is built for 1996-2000 Chrysler Sebring applications and follows OE-style fitment for vehicles with a welded factory exhaust assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit repair work\u003c\/li\u003e\n\u003cli\u003eLeft-side tail pipe application\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chrysler Sebring, left\u003c\/li\u003e\n\u003cli\u003ePart number 24920 for catalog and fitment lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 24920 tail pipe is intended for Chrysler Sebring owners replacing a worn, rusted, or damaged left exhaust outlet section. The aluminized steel material offers a practical balance of corrosion resistance and service life for everyday exhaust repair, while the OE replacement design supports factory-style routing and alignment. For shoppers searching for a 1996-2000 Chrysler Sebring left tail pipe, AP Exhaust 24920 provides a direct application match.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed interchange numbers for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a corroded left tail pipe on a 1996-2000 Chrysler Sebring\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after pipe damage or separation\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks caused by rust-through or cracking\u003c\/li\u003e\n\u003cli\u003eReturning the rear exhaust section to OE-style routing\u003c\/li\u003e\n\u003cli\u003eRepairing a vehicle with a welded factory exhaust assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 1996-2000 Chrysler Sebring, left. The notes indicate the OE system was a welded assembly, so related parts identified in the factory system should be inspected and replaced as needed during service. Verify side, routing, and existing exhaust configuration before installation. Part number 24920 should be matched to the vehicle application before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies replacement exhaust components for service and repair applications. This aluminized steel tail pipe is an original equipment replacement part built for the listed Chrysler Sebring fitment.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385505841333,"sku":"BBDL-24920","price":37.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_24920_Top_5169c246-1a68-42f5-8a69-0bd61b3efe4e.jpg?v=1774704114"},{"product_id":"ap-exhaust-28440-exhaust-pipe","title":"AP Exhaust 28440 Exhaust Pipe - Rear","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Honda Civic\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28440 is an aluminized steel exhaust pipe built as an original equipment replacement for select Honda applications. It is listed for rear-position use on 1992-2000 Honda Civic models and 1993-1995 Honda Civic del Sol models, including US-built Civic coverage noted in the fitment data.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit repair work\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application for select Honda Civic and Civic del Sol models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28440 for catalog and fitment lookup\u003c\/li\u003e\n\u003cli\u003eFits 1992-2000 Honda Civic, rear, with US-built coverage noted for select listings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28440 is a rear exhaust pipe made from aluminized steel to replace the factory pipe on supported Honda vehicles. This part is listed for 1992-2000 Honda Civic rear applications and 1993-1995 Honda Civic del Sol rear applications. The OE replacement design supports service work where the original exhaust pipe has rust, leaks, or structural damage. For Honda Civic exhaust repair, AP Exhaust 28440 provides a direct replacement option that matches the listed rear-position fitment.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed interchange numbers in the provided data. AP Exhaust 28440 is the catalog number to use when searching for a Honda Civic rear exhaust pipe or Honda Civic del Sol rear exhaust pipe replacement.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Repair\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eExhaust leaks from a corroded rear pipe\u003c\/li\u003e\n\u003cli\u003eRust-through or metal fatigue in the factory exhaust section\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust operation caused by a damaged pipe\u003c\/li\u003e\n\u003cli\u003eFailed inspection due to visible exhaust deterioration\u003c\/li\u003e\n\u003cli\u003eReplacement needs on a welded OE exhaust assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFitment notes state that the OE system was a welded assembly and recommend replacing all parts noted [1] during service. Confirm rear-position fitment before ordering and match the vehicle year, make, and model exactly. For 1992-2000 Honda Civic applications, the fitment data also includes a US-built note on select listings. AP Exhaust 28440 should be installed as part of a complete exhaust repair plan when the original welded assembly has multiple worn sections.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust lists this part as an original equipment replacement made from aluminized steel, supporting OE-style service for the specified Honda Civic and Civic del Sol applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506169013,"sku":"BBDL-28440","price":27.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28440_Top_bf26de66-7bbe-440c-b40b-2c2ca2d3b805.jpg?v=1774704116"},{"product_id":"ap-exhaust-28545-exhaust-pipe","title":"AP Exhaust 28545 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 28545 Exhaust Pipe for Windstar\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28545 is an aluminized steel exhaust pipe made as an original equipment replacement for the center exhaust routing on select Ford Windstar models. It is built for 1995-2003 Ford Windstar applications and supports a direct-fit repair for worn, rusted, or damaged exhaust piping.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in everyday exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for the center exhaust position\u003c\/li\u003e\n\u003cli\u003eFits 1995-2003 Ford Windstar, center\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28545 for easy identification\u003c\/li\u003e\n\u003cli\u003eBuilt for OE-style exhaust pipe replacement on the Ford Windstar\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is intended for drivers servicing the center section of the exhaust system on a Ford Windstar. The aluminized steel material helps provide a durable replacement option for vehicles exposed to heat, moisture, and road debris. If you are searching for a Ford Windstar center exhaust pipe, AP Exhaust 28545 offers a direct replacement format that matches the listed application years.\u003c\/p\u003e\u003cp\u003eAP Exhaust 28545 is a practical choice for restoring exhaust routing on 1995-2003 Ford Windstar models. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks caused by corrosion or cracking\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust flow on a Ford Windstar\u003c\/li\u003e\n\u003cli\u003eAddressing noise from a damaged center pipe section\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to OE-style routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year and center-position fitment before installation. Inspect adjoining exhaust components, hangers, and sealing surfaces for wear before installing the new pipe. For best results, compare the existing pipe shape and connection points to the replacement part number 28545 prior to assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures this part as an original equipment replacement exhaust pipe using aluminized steel for dependable service in the specified application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506201781,"sku":"BBDL-28545","price":138.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28545_Fro_033b6924-be1a-444d-bba7-6b8bf9d4ee7b.jpg?v=1774704116"},{"product_id":"ap-exhaust-28584-exhaust-pipe","title":"AP Exhaust 28584 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28584 Rear Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28584 is a rear exhaust pipe built as an original equipment replacement for select Chevrolet and Oldsmobile applications. Made from aluminized steel, it is intended for direct-fit service on vehicles that use a rear exhaust section in a welded OE system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system replacement service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2004-2005 Chevrolet Classic, rear\u003c\/li\u003e\n\u003cli\u003eFits 1997-2003 Chevrolet Malibu, rear\u003c\/li\u003e\n\u003cli\u003eFits 1997-1999 Chevrolet Malibu, rear, exc. Hybrid\u003c\/li\u003e\n\u003cli\u003eFits 1997-1999 Oldsmobile Cutlass, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 28584 rear exhaust pipe is built for vehicles with a welded OE exhaust assembly, where the rear section is serviced as part of the factory-style exhaust layout. The aluminized steel material provides a practical replacement option for corrosion-prone exhaust piping, and the OE replacement design supports a straightforward match to the original rear pipe location. It is a direct-fit choice for Chevrolet Malibu, Chevrolet Classic, and Oldsmobile Cutlass applications listed in the fitment data. AP Exhaust 28584 is a focused replacement part for restoring the rear exhaust path on these vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or damaged rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after a welded factory pipe section fails\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks at the rear section of the system\u003c\/li\u003e\n\u003cli\u003eAddressing noise from a cracked or separated exhaust pipe\u003c\/li\u003e\n\u003cli\u003eReturning a Chevrolet Malibu, Chevrolet Classic, or Oldsmobile Cutlass exhaust system to OE-style routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2004-2005 Chevrolet Classic, rear. Fits 1997-2003 Chevrolet Malibu, rear. Fits 1997-1999 Chevrolet Malibu, rear, exc. Hybrid. Fits 1997-1999 Oldsmobile Cutlass, rear. Because the OE system was a welded assembly, it is recommended that all parts noted in the application be replaced together. Verify the rear exhaust routing and vehicle configuration before installation. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures replacement exhaust components for service applications that require OE-style fit and material selection. Part number 28584 is an aluminized steel rear exhaust pipe intended for the listed vehicle applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506267317,"sku":"BBDL-28584","price":26.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28584_Top_b1891c9d-b291-4f71-bf45-a0e57b5bd27d.jpg?v=1774704116"},{"product_id":"ap-exhaust-28604-exhaust-pipe","title":"AP Exhaust 28604 Exhaust Pipe - Center, Front Center or Rear","description":"\u003ch2\u003eAP Exhaust 28604 Exhaust Pipe for Ford F-150 Heritage and F-150\u003c\/h2\u003e\u003cp\u003eAP Exhaust part number 28604 is an OE replacement exhaust pipe made from aluminized steel for direct-fit service on select Ford trucks. It is built for center, rear, and front center applications across 1998-2004 Ford F-150, F-150 Heritage, and F-250 configurations listed below.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eCompatible with 1998-2004 Ford F-150 Heritage and F-150 applications in listed positions\u003c\/li\u003e\n\u003cli\u003eCompatible with 1998-1999 Ford F-250 applications under 8500 lbs. G.V.W.\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 28604 for center, rear, and front center exhaust routing where specified\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28604 is an exhaust pipe engineered as an original equipment replacement for select Ford truck exhaust layouts. The aluminized steel construction is suited for exhaust system service where a factory-style pipe section is needed to restore proper routing and connection points. This part number is used across multiple applications, including Fits 2004 Ford F-150 Heritage, Center; Fits 2004 Ford F-150 Heritage, Center; Fits 1998-2003 Ford F-150, Center; Fits 1998-2001 Ford F-150, Rear; Fits 1998-1999 Ford F-250, Front Center; and Fits 1998-1999 Ford F-250, Center. If you are sourcing an AP Exhaust 28604 exhaust pipe for a Ford F-150 Heritage or Ford F-150 repair, this OE replacement format supports direct service on the listed truck configurations.\u003c\/p\u003e\u003ch2\u003eCommon Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or damaged exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust routing on a Ford F-150 Heritage or Ford F-150\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks caused by pipe corrosion or cracking\u003c\/li\u003e\n\u003cli\u003eRepairing a worn center, rear, or front center exhaust segment\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to factory-style layout on listed Ford trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, wheelbase, position, and notes before ordering. This part is listed for 2004 Ford F-150 Heritage center applications with 139-inch wheelbase, including the old body style note, 1998-2003 Ford F-150 center applications with 139-inch wheelbase, 1998-2001 Ford F-150 rear applications for all wheelbases, and 1998-1999 Ford F-250 front center or center applications under 8500 lbs. G.V.W. Match the exhaust routing and mounting location to the existing system before installation. This part number, 28604, should be compared against the removed pipe for length, bends, and connection style.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures OE replacement exhaust components for service applications that require factory-style fitment and material selection. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506332853,"sku":"BBDL-28604","price":22.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28604_Top.jpg?v=1774704117"},{"product_id":"ap-exhaust-28605-exhaust-pipe","title":"AP Exhaust 28605 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28605 Rear Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28605 is a rear exhaust pipe built as an original equipment replacement for select Nissan Xterra applications. It uses aluminized steel for corrosion resistance and OE-style fitment, making it a direct replacement choice for rear exhaust service on the Nissan Xterra.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for durable exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for OE-style fitment\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Nissan Xterra, rear\u003c\/li\u003e\n\u003cli\u003ePart number 28605 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eCompatible with 2001-2002 Nissan Xterra, rear. Also fits 2000 Nissan Xterra, rear, including 3.3L 2WD and 4WD models for California emissions and Federal emissions applications. OE system was a welded assembly, and AP Exhaust 28605 is intended for service replacement on those rear exhaust configurations.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust or corrosion in the rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a damaged welded assembly\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow caused by pipe deterioration\u003c\/li\u003e\n\u003cli\u003eNoise from cracks, holes, or failed joints in the rear section\u003c\/li\u003e\n\u003cli\u003eReplacement needs after OE exhaust system wear on Nissan Xterra models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFor 2000-2002 Nissan Xterra applications, review the existing OE welded exhaust assembly before installation. The fitment notes recommend replacing all parts noted [1] when servicing the rear exhaust section. Confirm emissions configuration and rear position before ordering or installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust lists this part as an original equipment replacement, and the aluminized steel construction supports long-term exhaust service in a direct-fit replacement format.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506398389,"sku":"BBDL-28605","price":41.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28605_Top.jpg?v=1774704118"},{"product_id":"ap-exhaust-28617-exhaust-pipe","title":"AP Exhaust 28617 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28617 Rear Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28617 is an aluminized steel exhaust pipe made as an original equipment replacement for select Toyota Tundra applications. It is built for rear-position fitment on 2000-2002 Toyota Tundra models, including California and non-California configurations noted in the fitment data.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Toyota Tundra, rear\u003c\/li\u003e\n\u003cli\u003ePart number 28617 for application matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 28617 exhaust pipe is specified for 2000-2002 Toyota Tundra rear exhaust service. The OE system was a welded assembly, so replacement planning should account for the related parts identified in the vehicle notes. For buyers searching for a 2000-2002 Toyota Tundra rear exhaust pipe or AP Exhaust 28617 for Toyota Tundra, this part matches the listed rear-position applications directly.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or corroded rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust routing after OE pipe damage\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks at the rear section\u003c\/li\u003e\n\u003cli\u003eServicing a welded OE exhaust assembly on Toyota Tundra\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify year, model, rear position, and California emissions notes before ordering. Because the original equipment system was welded, inspect the adjoining exhaust components and replace the related parts listed for the vehicle as needed. Confirm alignment and fitment against the existing exhaust layout before final installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies this part as an OE replacement exhaust component built from aluminized steel for the listed Toyota Tundra applications. Part number 28617 is intended to match the specified rear exhaust pipe fitment for 2000-2002 Toyota Tundra models.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506496693,"sku":"BBDL-28617","price":34.57,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28617_Top.jpg?v=1774704118"},{"product_id":"ap-exhaust-28623-exhaust-pipe","title":"AP Exhaust 28623 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28623 Rear Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28623 is an aluminized steel exhaust pipe built as an original equipment replacement for the rear section on select Ford Excursion applications. It is a direct-fit service part for 2000-2005 Ford Excursion rear exhaust repair, with fitment coverage that matches the OE-style layout used on these vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Ford Excursion, rear\u003c\/li\u003e\n\u003cli\u003ePart number 28623 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 28623 exhaust pipe is intended for rear exhaust system replacement on the Ford Excursion. The aluminized steel material is commonly used in exhaust service parts for corrosion resistance and durability in everyday driving conditions. As an original equipment replacement, it follows the OE-style configuration needed for a proper repair on 2000-2005 Ford Excursion rear exhaust applications. If you are replacing a damaged or rusted rear pipe on a Ford Excursion, part number 28623 provides a direct service option for the correct vehicle and position.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eExhaust leaks caused by rusted or cracked rear piping\u003c\/li\u003e\n\u003cli\u003eNoise from a damaged rear exhaust section\u003c\/li\u003e\n\u003cli\u003eFailed inspection due to exhaust deterioration\u003c\/li\u003e\n\u003cli\u003eFitment issues after replacing a welded OE exhaust assembly\u003c\/li\u003e\n\u003cli\u003eCorrosion-related exhaust system damage on Ford Excursion models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2000-2005 Ford Excursion, rear. The OE system was a welded assembly, and AP Exhaust notes that all parts identified in the original system should be replaced when servicing this section. Verify the rear exhaust routing and connection points before installation to confirm the correct OE-style replacement path for your vehicle. Part number 28623 should be matched to the rear position only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement, and the aluminized steel construction supports standard exhaust service requirements for the listed Ford Excursion applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506529461,"sku":"BBDL-28623","price":30.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28623_Top.jpg?v=1774704118"},{"product_id":"ap-exhaust-28624-exhaust-pipe","title":"AP Exhaust 28624 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 28624 Exhaust Pipe for OE Replacement\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28624 is an aluminized steel exhaust pipe built as an original equipment replacement for select GM minivans. It is a direct-fit solution for restoring exhaust routing on applications where the OE system was originally welded together.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in everyday driving conditions\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for OE-style fit and function\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Chevrolet Uplander, Pontiac Montana, Buick Terraza, Saturn Relay, and Oldsmobile Silhouette applications\u003c\/li\u003e\n\u003cli\u003eFits center and N\/A-position applications listed in the vehicle fitment data\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28624 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28624 is an exhaust pipe engineered for vehicles that used a welded OE exhaust assembly. This part is intended for repair work where the original pipe section has rust, leaks, or structural damage and the factory exhaust path needs to be restored. The aluminized steel material helps provide a durable replacement option for daily-driven vehicles, while the OE replacement design supports proper alignment with the factory exhaust system. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 2005-2008 Chevrolet Uplander, N\/A; 2007-2008 Pontiac Montana, N\/A; 2005-2007 Buick Terraza, N\/A; 2005-2007 Saturn Relay, N\/A; 2005-2006 Pontiac Montana, N\/A; 2002-2005 Pontiac Montana, Center; 2002-2004 Oldsmobile Silhouette, Center. Search terms such as 2005 Chevrolet Uplander exhaust pipe replacement, 2007 Pontiac Montana exhaust pipe, and 2002 Oldsmobile Silhouette center exhaust pipe all point to this application family.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks in a welded factory system\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after underbody corrosion damage\u003c\/li\u003e\n\u003cli\u003eAddressing noise from a cracked or separated pipe\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to proper routing on listed GM minivans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eOE system was a welded assembly, so related parts noted in the fitment data should be inspected before installation. Confirm the vehicle’s exact year, make, model, and suspension configuration before ordering, especially for Chevrolet Uplander, Pontiac Montana, Buick Terraza, and Saturn Relay applications. For 2002-2005 Pontiac Montana and 2002-2004 Oldsmobile Silhouette, verify the center-position fitment and the door decal code noted in the application data.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies replacement exhaust components for OE-style service applications. Part number 28624 is built as an original equipment replacement using aluminized steel for dependable service in the listed vehicle applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506562229,"sku":"BBDL-28624","price":38.72,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28624_Top_e54c440f-5f9d-45f9-b9ec-d74ac001d098.jpg?v=1774704119"},{"product_id":"ap-exhaust-28693-exhaust-pipe","title":"AP Exhaust 28693 Exhaust Pipe - Rear","description":"\u003ch2\u003eRear Exhaust Pipe for Ford F-150 Heritage\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28693 is a rear exhaust pipe built as an original equipment replacement for select Ford F-150 applications. Made from aluminized steel, it is specified for rear-position fitment and supports direct replacement needs on 2002-2004 Ford F-150 and 2004 Ford F-150 Heritage models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2004 Ford F-150 Heritage, rear, including all wheelbase and Old Body Style notes where listed\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Ford F-150, rear, all wheelbase configurations\u003c\/li\u003e\n\u003cli\u003eAP Exhaust 28693 for targeted exhaust pipe replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 28693 exhaust pipe is intended for rear exhaust routing on the listed Ford trucks. The aluminized steel material provides a practical replacement option for restoring the exhaust path on a Ford F-150 or Ford F-150 Heritage when the original pipe is damaged, rusted, or no longer sealing properly. AP Exhaust 28693 is an OE replacement part that follows the listed vehicle fitment for 2002-2004 applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a corroded rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after pipe damage\u003c\/li\u003e\n\u003cli\u003eCorrecting exhaust leaks caused by rust-through or separation\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to factory-style routing\u003c\/li\u003e\n\u003cli\u003eServicing rear exhaust sections on Ford F-150 and Ford F-150 Heritage trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and rear-position fitment before installation. Confirm wheelbase and body-style notes for 2004 Ford F-150 Heritage applications, including Old Body Style listings. Compare the existing pipe routing and connection points to the replacement part before removal to ensure proper alignment.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28693 is an OE replacement exhaust pipe built for the listed factory applications. Its aluminized steel construction supports service replacement use on the specified Ford trucks.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506594997,"sku":"BBDL-28693","price":26.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28693_Top_6036a1b8-0da0-4447-9db6-10789873e905.jpg?v=1774704119"},{"product_id":"ap-exhaust-28696-exhaust-pipe","title":"AP Exhaust 28696 Exhaust Pipe - Rear","description":"\u003ch2\u003eRear Exhaust Pipe for Toyota Corolla\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28696 is a rear exhaust pipe built for direct replacement service on select Toyota Corolla models. It uses aluminized steel construction and is specified as an original equipment replacement for a straightforward fit on the rear exhaust section.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Toyota Corolla, rear\u003c\/li\u003e\n\u003cli\u003ePart number 28696 for ordering and catalog lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28696 is an OE-style rear exhaust pipe for 2003-2005 Toyota Corolla models, excluding the XRS model. The aluminized steel material is commonly used in exhaust service parts for corrosion resistance and dependable fitment in everyday repair work. This part number, 28696, is intended for rear exhaust replacement where the original pipe has rust, damage, or restricted flow.\u003c\/p\u003e\u003cp\u003eCompatible With 2003-2005 Toyota Corolla, rear. This part cross-references no listed interchange numbers in the provided data.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or damaged rear exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust routing on a 2003-2005 Toyota Corolla\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks at the rear pipe section\u003c\/li\u003e\n\u003cli\u003eCorrecting fitment issues from a failed OE pipe\u003c\/li\u003e\n\u003cli\u003eMaintaining factory-style exhaust layout on Corolla models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle fitment before installation: Fits 2003-2005 Toyota Corolla, rear, excluding XRS models. Compare the existing pipe routing, hanger locations, and connection points to the original part before removal. Exhaust components should be inspected for related wear, corrosion, or gasket damage during service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement, indicating OE-style application coverage for the listed Toyota Corolla fitment. The aluminized steel construction supports standard exhaust repair use in the rear section.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506627765,"sku":"BBDL-28696","price":49.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28696_Top.jpg?v=1774704119"},{"product_id":"ap-exhaust-28707-exhaust-pipe","title":"AP Exhaust 28707 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 28707 Center Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28707 is an aluminized steel exhaust pipe built as an original equipment replacement for select GM full-size SUVs. It is engineered for center exhaust routing on 2001-2006 Chevrolet Tahoe, 2001-2006 GMC Yukon, 2001-2006 GMC Yukon XL 1500, and 2002-2005 Cadillac Escalade applications with a welded OE exhaust system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eDirect-fit coverage for select Chevrolet Tahoe, GMC Yukon, GMC Yukon XL 1500, and Cadillac Escalade models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28707\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28707 is a replacement exhaust pipe for vehicles that use a welded factory exhaust assembly. The aluminized steel construction is selected for standard exhaust service applications, and the OE replacement design supports restoration of the factory exhaust path on the listed Chevrolet Tahoe, GMC Yukon, GMC Yukon XL 1500, and Cadillac Escalade models. For buyers searching for a center exhaust pipe for 2001-2006 Chevrolet Tahoe or a replacement exhaust pipe for 2001-2006 GMC Yukon, this part number 28707 matches the specified center-position fitment.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorroded or damaged center exhaust piping\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a failed welded assembly section\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow caused by rust or physical damage\u003c\/li\u003e\n\u003cli\u003eReplacement needs on OE welded exhaust systems\u003c\/li\u003e\n\u003cli\u003eService work on 2001-2006 Chevrolet Tahoe and GMC Yukon exhaust systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2001-2006 Chevrolet Tahoe, Center. Fits 2001-2006 GMC Yukon, Center. Fits 2001-2006 GMC Yukon XL 1500, Center. Fits 2002-2005 Cadillac Escalade, N\/A. The OE system was a welded assembly, and AP Exhaust notes that all parts identified in the application should be replaced. Verify the vehicle’s exhaust layout and position before installation. AP Exhaust 28707 is intended for the listed center-exhaust applications only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement exhaust pipe made from aluminized steel for the specified applications. Part number 28707 is built to match the listed OE-style fitment requirements for the supported GM SUVs.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506726069,"sku":"BBDL-28707","price":51.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28707_Top_ecfecd8c-fff9-40bb-a979-7405e2d2eea8.jpg?v=1774704120"},{"product_id":"ap-exhaust-28727-exhaust-pipe","title":"AP Exhaust 28727 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 28727 Exhaust Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28727 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford Super Duty applications. It is listed for center position fitment on 1999-2004 Ford F-250 Super Duty and Ford F-350 Super Duty models with a 158-inch wheelbase, including OE systems that were originally welded assemblies.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a Ford F-250 Super Duty exhaust pipe or a Ford F-350 Super Duty center exhaust pipe, AP Exhaust 28727 provides a direct replacement option for the specified factory configuration.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system replacement use\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 1999-2004 Ford F-250 Super Duty and Ford F-350 Super Duty, 158-inch wheelbase configurations\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28727 for catalog and service matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28727 is engineered for the center section of the exhaust system on select Ford Super Duty trucks. The aluminized steel material is commonly used in exhaust service parts because it offers a practical balance of corrosion resistance and durability for replacement applications. This part number, 28727, is specified as an original equipment replacement, making it a straightforward choice when restoring the factory exhaust layout on a 1999-2004 Ford F-250 Super Duty or Ford F-350 Super Duty with a 158-inch wheelbase.\u003c\/p\u003e\u003cp\u003eThis exhaust pipe is listed for vehicles where the OE system was a welded assembly, so matching the correct configuration is important during service. AP Exhaust 28727 is a fitment-specific replacement for center exhaust routing on these Ford Super Duty trucks.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust or corrosion in the center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by damaged factory piping\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust operation from a compromised pipe section\u003c\/li\u003e\n\u003cli\u003eFailed replacement of a welded OE exhaust assembly\u003c\/li\u003e\n\u003cli\u003eRestoration of the factory exhaust path on Ford F-250 Super Duty and Ford F-350 Super Duty trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify wheelbase, model year, and center-position routing before ordering. This part is listed for 158-inch wheelbase trucks only, and the OE system was a welded assembly on the referenced applications. It is recommended that all parts noted in the OE service reference be replaced together when performing the repair. Confirm the existing exhaust layout on the vehicle before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies replacement exhaust components for service applications, and 28727 is cataloged as an OE replacement part for the listed Ford Super Duty fitments. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506758837,"sku":"BBDL-28727","price":46.81,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28727_Top_a8d43fd8-68b9-4b37-8eb9-9fb9c7fde8c0.jpg?v=1774704120"},{"product_id":"ap-exhaust-28736-exhaust-pipe","title":"AP Exhaust 28736 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28736 Rear Exhaust Pipe\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28736 is an aluminized steel rear exhaust pipe built as an original equipment replacement for select Ford F-150 and Lincoln Mark LT applications. It is shaped for rear exhaust service on the listed vehicles and supports direct replacement of the factory pipe where OE fitment is confirmed.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2005-2008 Ford F-150, rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Ford F-150, rear, New Body Style\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Lincoln Mark LT, rear\u003c\/li\u003e\n\u003cli\u003ePart number 28736 for application matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28736 is a rear exhaust pipe for OE-style replacement on the Ford F-150 and Lincoln Mark LT. The aluminized steel construction is selected for exhaust system use, and the part is listed as an original equipment replacement to match the factory configuration on the covered vehicles. This part number 28736 is a direct reference for buyers searching for a rear exhaust pipe for 2005-2008 Ford F-150, rear service, 2004-2008 Ford F-150 New Body Style, rear service, or 2006-2008 Lincoln Mark LT, rear service.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorroded or rusted rear exhaust pipe sections\u003c\/li\u003e\n\u003cli\u003eExhaust leaks from a damaged pipe\u003c\/li\u003e\n\u003cli\u003eFactory pipe replacement after underbody wear\u003c\/li\u003e\n\u003cli\u003eFitment replacement for welded OE exhaust assemblies\u003c\/li\u003e\n\u003cli\u003eService needs on Ford F-150 and Lincoln Mark LT rear exhaust routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2005-2008 Ford F-150, rear. Fits 2004-2008 Ford F-150, rear, New Body Style. Fits 2006-2008 Lincoln Mark LT, rear. The OE system was a welded assembly, and AP Exhaust notes that all parts identified [1] should be replaced. Verify the vehicle body style and rear exhaust configuration before installation. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust lists this part as an original equipment replacement, supporting OE-style service fitment for the specified Ford and Lincoln applications.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506824373,"sku":"BBDL-28736","price":25.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28736_Top.jpg?v=1774704120"},{"product_id":"ap-exhaust-28739-exhaust-pipe","title":"AP Exhaust 28739 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28739 Rear Exhaust Pipe for Ford F-150\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28739 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford F-150 rear exhaust applications. It is listed for 2004-2008 Ford F-150 and 2005-2008 Ford F-150 rear positions, with fitment notes for OE welded-system replacement requirements.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and corrosion resistance\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eRear exhaust pipe application for Ford F-150 models\u003c\/li\u003e\n\u003cli\u003ePart number 28739 for accurate ordering and catalog matching\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Ford F-150, rear, with note for Heritage Series exclusion on 2004-2008 applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28739 is a rear exhaust pipe for Ford F-150 trucks, engineered as an OE replacement for factory exhaust service. The aluminized steel material is commonly used in exhaust components where a balance of durability and value is needed. This part number 28739 applies to 2005-2008 Ford F-150 rear exhaust service and also to 2004-2008 Ford F-150 rear applications, excluding Heritage Series (Old Body Style). The OE system was a welded assembly, and AP Exhaust notes that related parts identified in the system should be replaced as needed during service.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a damaged or rusted rear exhaust pipe on a Ford F-150\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust routing after corrosion or impact damage\u003c\/li\u003e\n\u003cli\u003eServicing a factory welded exhaust assembly on 2004-2008 Ford F-150 trucks\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks caused by pipe deterioration or failed joints\u003c\/li\u003e\n\u003cli\u003eReturning the rear section of the exhaust system to OE-style configuration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2005-2008 Ford F-150, rear. Fits 2004-2008 Ford F-150, rear, except Heritage Series (Old Body Style). Because the OE system was a welded assembly, inspect the adjoining exhaust components before installation and replace any related parts noted in the factory system if they are worn or damaged. Verify vehicle year, model, and rear-position application before ordering. This part number 28739 is intended for direct replacement service on the listed Ford F-150 applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies OE replacement exhaust components for service and repair applications. This part is built to match the listed factory-style rear exhaust fitment for the specified Ford F-150 model years.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506857141,"sku":"BBDL-28739","price":25.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28739_Top_cbf5e033-f89c-446c-84fc-345d7115d23d.jpg?v=1774704121"},{"product_id":"ap-exhaust-28746-exhaust-pipe","title":"AP Exhaust 28746 Exhaust Pipe - Center","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Explorer and Mountaineer\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28746 is an aluminized steel exhaust pipe built as an original equipment replacement for select 2000-2001 Ford Explorer and Mercury Mountaineer applications. It is specified for center position use and matches the OE welded-assembly layout used on these vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eDirect fit for select 2000-2001 Ford Explorer and Mercury Mountaineer models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28746\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eCompatible with 2001 Ford Explorer, center, including 4-door models built from 12\/99. Compatible with 2001 Mercury Mountaineer, center. Compatible with 2000 Ford Explorer, center, including 4-door models built from 12\/99. Compatible with 2000 Mercury Mountaineer, center.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust damage in the center exhaust section\u003c\/li\u003e\n\u003cli\u003eCracked or leaking OE exhaust pipe sections\u003c\/li\u003e\n\u003cli\u003eFitment issues after replacing a welded factory exhaust assembly\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust routing on Ford Explorer and Mercury Mountaineer models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eOE system was a welded assembly, so related parts noted in the catalog should be replaced as needed during service. Verify vehicle build date and center-position fitment before installation. Professional exhaust installation is recommended for proper alignment and sealing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28746 is an OE replacement exhaust pipe made to service the factory-style exhaust layout on the listed vehicles. Aluminized steel construction supports standard exhaust system repair needs.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506922677,"sku":"BBDL-28746","price":34.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28746_Top_031d203c-92fb-451d-8481-0efe2d49c090.jpg?v=1774704121"},{"product_id":"ap-exhaust-28762-exhaust-pipe","title":"AP Exhaust 28762 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 28762 Exhaust Pipe for OE Replacement\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28762 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford Explorer and Mercury Mountaineer applications. It is listed for the center position and follows OE system requirements for 2006-2010 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and corrosion resistance\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit repair planning\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Ford Explorer, center\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Mercury Mountaineer, center\u003c\/li\u003e\n\u003cli\u003ePart number 28762 for catalog and fitment lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28762 is an OE-style exhaust pipe for the center section of the exhaust system on 2006-2010 Ford Explorer and 2006-2010 Mercury Mountaineer models. The aluminized steel construction is selected for standard exhaust service, and the part is positioned as an original equipment replacement for vehicles that used a welded OE assembly. For repair planning, AP Exhaust 28762 is a direct reference for center exhaust pipe replacement on these Ford and Mercury platforms.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust or corrosion in the center exhaust section\u003c\/li\u003e\n\u003cli\u003eCracks or leaks in the original welded pipe assembly\u003c\/li\u003e\n\u003cli\u003eExhaust noise from a damaged center pipe\u003c\/li\u003e\n\u003cli\u003eFailed emissions-related exhaust sealing at the pipe section\u003c\/li\u003e\n\u003cli\u003eRestoration of proper exhaust routing on Ford Explorer and Mercury Mountaineer models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2006-2010 Ford Explorer, center. Fits 2006-2010 Mercury Mountaineer, center. The OE system was a welded assembly, and AP Exhaust notes that related parts identified for the system should be replaced during service. Verify the vehicle’s exhaust layout and center-position configuration before installation. Part number 28762 should be matched to the vehicle application before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies this part as an original equipment replacement for the listed applications. The aluminized steel material supports standard exhaust-system service requirements for the 2006-2010 Ford Explorer and Mercury Mountaineer center exhaust position.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385506988213,"sku":"BBDL-28762","price":33.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28762_Top.jpg?v=1774704122"},{"product_id":"ap-exhaust-28790-exhaust-pipe","title":"AP Exhaust 28790 Exhaust Pipe - Rear","description":"\u003ch2\u003eAP Exhaust 28790 Exhaust Pipe for Ford F-150\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28790 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford F-150 applications. It is listed for 2009-2014 Ford F-150 models, including rear-position coverage on 2009-2010 trucks and broader 2011-2014 coverage with the noted wheelbase exception.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for factory-style fitment\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28790\u003c\/li\u003e\n\u003cli\u003eCompatible with 2009-2014 Ford F-150 applications listed below\u003c\/li\u003e\n\u003cli\u003eSupports repair of OE exhaust sections on welded factory systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28790 is an OE replacement exhaust pipe for Ford F-150 trucks that need a direct-fit style service part for the factory exhaust layout. The aluminized steel construction is suited for exhaust repair work where the original pipe section has corroded, been damaged, or needs replacement during system service. This part number 28790 is listed for 2009-2010 Ford F-150 rear applications and 2011-2014 Ford F-150 applications, excluding 126-inch wheelbase trucks. Because the OE system was a welded assembly, related parts noted in the fitment notes should be replaced as needed during repair.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or damaged exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after factory pipe failure\u003c\/li\u003e\n\u003cli\u003eRepairing welded OE exhaust assemblies on Ford F-150 trucks\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks caused by pipe deterioration\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to a serviceable configuration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2009-2010 Ford F-150, rear. Fits 2011-2014 Ford F-150, N\/A, excluding 126-inch wheelbase trucks. Verify the vehicle’s exhaust layout and wheelbase before ordering, since the OE system was a welded assembly and related parts may need replacement during service. Confirm the existing pipe routing and connection points against the vehicle before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust lists this part as an original equipment replacement, indicating OE-style application coverage for the specified Ford F-150 models. Part number 28790 is built from aluminized steel for exhaust system replacement service.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507086517,"sku":"BBDL-28790","price":20.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28790_Top.jpg?v=1774704122"},{"product_id":"ap-exhaust-28794-exhaust-pipe","title":"AP Exhaust 28794 Exhaust Pipe","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Ram HD\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28794 is an aluminized steel exhaust pipe built as an original equipment replacement for select heavy-duty Ram trucks. It is engineered for 2005-2009 Dodge Ram 2500 and 2005-2007 Dodge Ram 3500 applications with 140.50-inch or 160.50-inch wheelbase configurations.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit service on listed applications\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Dodge Ram 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2007 Dodge Ram 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28794 for catalog and service matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is intended for Ram HD exhaust repair where the factory pipe has rusted, cracked, or lost sealing integrity. The aluminized steel material provides a practical balance of durability and service life for daily-driven work trucks, while the OE replacement design supports a factory-style fit on the specified Dodge Ram 2500 and Dodge Ram 3500 wheelbase configurations. If you are replacing a damaged exhaust section on a 2005-2009 Dodge Ram 2500 or a 2005-2007 Dodge Ram 3500, AP Exhaust 28794 is a direct catalog match for those applications.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after pipe damage\u003c\/li\u003e\n\u003cli\u003eCorrecting exhaust leaks caused by corrosion or cracking\u003c\/li\u003e\n\u003cli\u003eRepairing a failed factory-style exhaust section on Ram HD trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify wheelbase before ordering: this part is listed for 140.50-inch and 160.50-inch wheelbase configurations. Confirm the existing pipe routing and connection points against the vehicle before installation, and inspect adjoining exhaust components for wear, corrosion, or gasket damage that could affect the repair. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies replacement exhaust components for service applications, and part 28794 is listed as an original equipment replacement exhaust pipe for the vehicles shown above.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507152053,"sku":"BBDL-28794","price":39.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28794_Top.jpg?v=1774704123"},{"product_id":"ap-exhaust-28807-exhaust-pipe","title":"AP Exhaust 28807 Exhaust Pipe - Rear","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Corolla\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28807 is an aluminized steel exhaust pipe built as an original equipment replacement for select Toyota Corolla applications. It is listed for rear and N\/A positions across 2009-2019 Corolla models, with fitment notes that reference the OE welded assembly design.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and replacement\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for select Toyota Corolla applications\u003c\/li\u003e\n\u003cli\u003eDesigned for rear and N\/A positions where listed in the fitment data\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28807 for direct catalog identification\u003c\/li\u003e\n\u003cli\u003eThis part cross-references 17430OD460 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28807 is an exhaust pipe intended for Toyota Corolla exhaust repair where the factory system used a welded assembly. The aluminized steel material supports routine exhaust system replacement needs, and the OE replacement designation makes it a practical choice for restoring the factory-style exhaust path on 2009-2019 Toyota Corolla models. If you are sourcing an exhaust pipe for a Toyota Corolla rear exhaust repair, part number 28807 provides a cataloged replacement option with application-specific fitment.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust damage in the exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eCracks or leaks in a welded factory exhaust assembly\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow caused by a damaged pipe\u003c\/li\u003e\n\u003cli\u003eNoise from a failing rear exhaust section\u003c\/li\u003e\n\u003cli\u003eNeed for OE-style replacement during exhaust system repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFitment is listed for 2014-2019 Toyota Corolla, N\/A; 2010-2013 Toyota Corolla, Rear; 2009-2013 Toyota Corolla, Rear; and 2009 Toyota Corolla, Rear. The fitment notes state that the OE system was a welded assembly and recommend replacing all parts noted [1] during service. Verify the vehicle year, position, and exhaust configuration before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement exhaust component made from aluminized steel for the listed Corolla applications. Part number 28807 is cataloged for direct replacement use where the OE welded exhaust assembly is being serviced.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507184821,"sku":"BBDL-28807","price":42.21,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28807_Top.jpg?v=1774704124"},{"product_id":"ap-exhaust-28812-exhaust-pipe","title":"AP Exhaust 28812 Exhaust Pipe - Center","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Super Duty Applications\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28812 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford Super Duty chassis cab applications. It is engineered for the 2003-2007 Ford F-250 Super Duty and 2003-2007 Ford F-350 Super Duty, with fitment that matches the listed OE configurations.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service and corrosion resistance\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for direct-fit service on listed applications\u003c\/li\u003e\n\u003cli\u003eFits 2003-2007 Ford F-250 Super Duty, N\/A, w\/ Narrow Frame, Chassis Cab\u003c\/li\u003e\n\u003cli\u003eFits 2003-2007 Ford F-350 Super Duty, center, w\/ Narrow Frame\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28812 for catalog and service reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is intended for replacement of the factory pipe in the exhaust system where the OE assembly was originally welded. The aluminized steel construction supports long-term exhaust service, while the OE replacement design helps maintain the factory routing and fitment expected on the Ford F-250 Super Duty and Ford F-350 Super Duty chassis cab platforms. For buyers searching for a Ford F-250 Super Duty exhaust pipe or Ford F-350 Super Duty center exhaust pipe, AP Exhaust 28812 provides a direct application match to the listed configurations.\u003c\/p\u003e\u003cp\u003eThis part cross-references Ford service part number 6C3Z5230A for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRusted or deteriorated factory exhaust piping\u003c\/li\u003e\n\u003cli\u003eCracked or leaking welded exhaust sections\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow caused by damaged pipe sections\u003c\/li\u003e\n\u003cli\u003eNoise from exhaust leaks at the pipe assembly\u003c\/li\u003e\n\u003cli\u003eService replacement needs on narrow frame chassis cab trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle configuration before ordering. Fits 2003-2007 Ford F-250 Super Duty, N\/A, w\/ Narrow Frame, Chassis Cab. Fits 2003-2007 Ford F-350 Super Duty, center, w\/ Narrow Frame. Because the OE system was a welded assembly, AP Exhaust recommends replacing the related parts noted in the application when servicing this section of the exhaust. Confirm routing, hanger locations, and connection points against the existing system before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28812 is an original equipment replacement exhaust pipe made to service the listed Ford Super Duty applications with the specified aluminized steel material.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507250357,"sku":"BBDL-28812","price":31.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28812_Top_053718dc-6c0e-43dc-a061-168d07102005.jpg?v=1774704124"},{"product_id":"ap-exhaust-28839-exhaust-pipe","title":"AP Exhaust 28839 Exhaust Pipe","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Ford and Mercury\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28839 is an aluminized steel exhaust pipe built as an original equipment replacement for select Ford and Mercury applications. It is listed for 2008-2009 Ford Taurus, 2008-2009 Ford Taurus X, 2009 Ford Flex, and 2008-2009 Mercury Sable, with notes for resonator eliminator use on specific vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eDirect-fit style replacement for listed Ford and Mercury applications\u003c\/li\u003e\n\u003cli\u003eCan be used as a resonator eliminator pipe on select models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 28839\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is intended for drivers replacing a worn, rusted, or damaged factory pipe on select 2008-2009 Ford Taurus, Ford Taurus X, Ford Flex, and Mercury Sable vehicles. AP Exhaust 28839 follows OE replacement specifications and uses aluminized steel to match common factory-style exhaust service needs. For shoppers searching for a 2009 Ford Flex exhaust pipe, 2008-2009 Ford Taurus exhaust pipe, or 2008-2009 Mercury Sable resonator eliminator pipe, this part number provides a fitment-specific option.\u003c\/p\u003e\u003cp\u003eThis part cross-references Ford OE part number 9G1Z5A212A for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust-through in the exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eCracked or leaking factory exhaust tubing\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow from a damaged pipe\u003c\/li\u003e\n\u003cli\u003eResonator delete or resonator eliminator service on listed applications\u003c\/li\u003e\n\u003cli\u003eReplacement of an OE-style exhaust pipe on Ford and Mercury models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, engine\/emissions configuration, and model before ordering. Fitment includes 2009 Ford Flex, 2008-2009 Ford Taurus (Federal, non-turbo SE\/SEL\/Limited), 2008-2009 Ford Taurus X (Federal emissions), and 2008-2009 Mercury Sable. The Taurus X listing is not for vehicles licensed in CA, CO, ME, or NY. Confirm the existing exhaust layout and resonator configuration before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures OE replacement exhaust components for service applications, and this pipe is built to match the listed factory-style fitment requirements for the specified Ford and Mercury vehicles.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507315893,"sku":"BBDL-28839","price":59.93,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28839_Top.jpg?v=1774704124"},{"product_id":"ap-exhaust-28848-exhaust-pipe","title":"AP Exhaust 28848 Exhaust Pipe","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Express and Savana\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28848 is an aluminized steel exhaust pipe built as an original equipment replacement for select Chevrolet Express and GMC Savana vans. It is listed for 2003-2009 Chevrolet Express 2500 and Express 3500, plus 2003-2009 GMC Savana 2500 and Savana 3500 with 4.8L or 6.0L engines and a 155-inch wheelbase.\u003c\/p\u003e\u003cp\u003eThis AP Exhaust 28848 pipe is a direct-fit style replacement for vehicles where the OE exhaust system was originally welded together. It is a practical choice when servicing a worn or damaged exhaust section on Chevrolet Express and GMC Savana applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 Chevrolet Express 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 Chevrolet Express 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 GMC Savana 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 GMC Savana 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFor 4.8L and 6.0L engine applications with 155-inch wheelbase\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28848 is engineered for OE-style exhaust service on full-size GM vans. The aluminized steel construction provides a durable replacement option for exhaust routing and repair, while the original equipment replacement design supports proper fitment on the listed Chevrolet Express and GMC Savana models. This part cross-references GM OE numbers 25851450 and 25851453 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust damage in the exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eCracked or leaking exhaust tubing\u003c\/li\u003e\n\u003cli\u003eNoise caused by a failing exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoration of a damaged OE welded exhaust assembly\u003c\/li\u003e\n\u003cli\u003eReplacement needs during exhaust system repair on high-mileage vans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFitment is specific to 2003-2009 Chevrolet Express 2500 and Express 3500, plus 2003-2009 GMC Savana 2500 and Savana 3500 with 4.8L or 6.0L engines and a 155-inch wheelbase. The OE system was a welded assembly, so AP Exhaust recommends replacing all related parts noted for the application during service. Verify the existing exhaust layout and vehicle configuration before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 28848 is an OE replacement exhaust pipe built to match the listed application requirements for Chevrolet Express and GMC Savana vans.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507348661,"sku":"BBDL-28848","price":50.77,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_28848_Top.jpg?v=1774704124"},{"product_id":"ap-exhaust-34908-exhaust-tail-pipe","title":"AP Exhaust 34908 Exhaust Tail Pipe - Front","description":"\u003ch2\u003eAP Exhaust 34908 Tail Pipe for Explorer and Mountaineer\u003c\/h2\u003e\u003cp\u003eAP Exhaust 34908 is an aluminized steel exhaust tail pipe built as an original equipment replacement for select Ford and Mercury SUVs. It is engineered for front-position applications on the 2006-2010 Ford Explorer and 2006-2010 Mercury Mountaineer, where the OE exhaust system was supplied as a welded assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system durability\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eFront-position tail pipe application\u003c\/li\u003e\n\u003cli\u003eDirect fit for select 2006-2010 Ford Explorer and Mercury Mountaineer models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 34908\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust 34908 tail pipe is intended for drivers replacing a front exhaust section on a Ford Explorer or Mercury Mountaineer with OE-style fitment requirements. The aluminized steel construction provides a practical balance of corrosion resistance and service life for everyday exhaust repair work. Because the factory system was a welded assembly, replacement planning should account for the related parts noted in the vehicle fitment information. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRust or corrosion in the front exhaust tail pipe\u003c\/li\u003e\n\u003cli\u003eExhaust leaks caused by damaged welded sections\u003c\/li\u003e\n\u003cli\u003eNoisy exhaust operation from a failing pipe section\u003c\/li\u003e\n\u003cli\u003eFitment issues when replacing OE welded exhaust components\u003c\/li\u003e\n\u003cli\u003eInspection failures related to visible exhaust deterioration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 2006-2010 Ford Explorer, front. Fits 2006-2010 Mercury Mountaineer, front. Because the OE system was a welded assembly, verify the condition of adjoining exhaust parts before installation and replace any related components identified for the vehicle. Confirm alignment, hanger placement, and connection points against the existing exhaust layout before final tightening.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust identifies this part as an original equipment replacement, making it a direct-fit service part for the listed applications. Part number 34908 is built to match the OE-style exhaust repair need for these vehicles.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507610805,"sku":"BBDL-34908","price":40.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_34908_Top.jpg?v=1774704127"},{"product_id":"ap-exhaust-38012-exhaust-pipe","title":"AP Exhaust 38012 Exhaust Pipe","description":"\u003ch2\u003eAP Exhaust 38012 Exhaust Pipe for Traverse and Outlook\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38012 is an aluminized steel exhaust pipe made as an original equipment replacement for select Chevrolet Traverse and Saturn Outlook applications. It is built for direct-fit service on vehicles with welded OE exhaust assemblies, where replacing the affected exhaust section is the practical repair path.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system durability\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part for OE-style fitment\u003c\/li\u003e\n\u003cli\u003eFits 2009-2017 Chevrolet Traverse, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 Saturn Outlook, N\/A\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 38012\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is engineered for the Chevrolet Traverse and Saturn Outlook platforms listed in the fitment data. The aluminized steel material provides a practical balance of corrosion resistance and service life for replacement exhaust work, while the OE replacement design supports a factory-style repair on systems originally built as welded assemblies. AP Exhaust 38012 is a direct replacement choice when servicing the exhaust pipe section on these vehicles.\u003c\/p\u003e\u003cp\u003eThis part cross-references GM OE numbers 15903511 and 20813841 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a damaged or rusted exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow on a Chevrolet Traverse or Saturn Outlook\u003c\/li\u003e\n\u003cli\u003eRepairing leaks caused by corrosion at the pipe assembly\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust noise from a compromised pipe\u003c\/li\u003e\n\u003cli\u003eServicing welded OE exhaust systems that require section replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2009-2017 Chevrolet Traverse, N\/A. Fits 2007-2010 Saturn Outlook, N\/A. The OE system was a welded assembly, so the fitment notes recommend replacing all parts identified for the application. Verify the vehicle year, model, and exhaust configuration before installation. AP Exhaust 38012 should be matched to the listed application only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures OE replacement exhaust components for direct-fit service applications. This part number 38012 is built to replace the original exhaust pipe on the listed vehicles using aluminized steel construction.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507643573,"sku":"BBDL-38012","price":49.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38012_Fro_df7a00bb-2204-4d01-a720-a4f4e12620e7.jpg?v=1774704127"},{"product_id":"ap-exhaust-38014-exhaust-pipe","title":"AP Exhaust 38014 Exhaust Pipe","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Silverado and Sierra HD\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38014 is an aluminized steel exhaust pipe built as an original equipment replacement for select Chevrolet Silverado HD and GMC Sierra HD applications. It is specified for 2007-2010 Silverado 2500 HD, Silverado 3500 HD, Sierra 2500 HD, and Sierra 3500 HD models with the 133-inch wheelbase, plus 2007 Classic Series HD applications listed below.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit service on listed applications\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 Chevrolet Silverado 2500 HD, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 Chevrolet Silverado 3500 HD, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 GMC Sierra 2500 HD, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 GMC Sierra 3500 HD, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007 Chevrolet Silverado 2500 HD Classic, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007 Chevrolet Silverado 3500 Classic, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007 GMC Sierra 2500 HD Classic, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007 GMC Sierra 3500 Classic, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis AP Exhaust 38014 exhaust pipe is made for owners replacing a worn, rusted, or damaged OE pipe on Silverado HD and Sierra HD trucks. The aluminized steel material is selected for exhaust-system durability, and the OE replacement design follows the factory application notes for the 133-inch wheelbase trucks listed in the fitment data. This part cross-references GM OE 25929101 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Replacement Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRepairing exhaust leaks caused by corrosion or pipe damage\u003c\/li\u003e\n\u003cli\u003eReplacing a factory welded exhaust section on the listed HD trucks\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust routing after OE pipe failure\u003c\/li\u003e\n\u003cli\u003eAddressing noise from a cracked, separated, or deteriorated exhaust pipe\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to factory-style configuration on supported Silverado and Sierra models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify wheelbase and model configuration before ordering. The fitment notes specify 133-inch wheelbase applications, and several OE systems were welded assemblies; the notes recommend replacing all parts identified in the factory system when servicing these trucks. Confirm the vehicle is one of the listed Chevrolet Silverado HD or GMC Sierra HD applications before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38014 is an OE replacement exhaust pipe built to match the listed factory applications for Silverado and Sierra HD trucks. The aluminized steel construction supports long-term exhaust service in a direct replacement format.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507676341,"sku":"BBDL-38014","price":81.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38014_Fro_2952390d-6860-4c41-ba57-422aeb3e5252.jpg?v=1774704127"},{"product_id":"ap-exhaust-38017-exhaust-pipe","title":"AP Exhaust 38017 Exhaust Pipe","description":"\u003ch2\u003eAP Exhaust 38017 Exhaust Pipe for Hyundai Sonata\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38017 is an aluminized steel exhaust pipe made as an original equipment replacement for select Hyundai Sonata applications. It is built for 2011-2014 Hyundai Sonata models with a single exhaust system and matches the OE-style service need for this platform.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design for direct-fit service on the listed application\u003c\/li\u003e\n\u003cli\u003eFits 2011-2014 Hyundai Sonata, N\/A position, single exhaust\u003c\/li\u003e\n\u003cli\u003ePart number 38017 for catalog and cross-reference lookup\u003c\/li\u003e\n\u003cli\u003eCross-references Hyundai OE part number 28600-3Q330 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis AP Exhaust exhaust pipe is intended for the 2011-2014 Hyundai Sonata where the OE system was supplied as a welded assembly. The aluminized steel construction supports replacement of the exhaust section with a service part that follows the original equipment layout. Use part number 38017 when searching for a Hyundai Sonata exhaust pipe replacement that matches the listed OE application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a damaged or rusted exhaust pipe section\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after corrosion-related failure\u003c\/li\u003e\n\u003cli\u003eServicing a welded OE exhaust assembly with a replacement pipe\u003c\/li\u003e\n\u003cli\u003eAddressing exhaust leaks at the original pipe section\u003c\/li\u003e\n\u003cli\u003eRepairing a single exhaust Hyundai Sonata system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 2011-2014 Hyundai Sonata, N\/A position. The OE system was a welded assembly, so related parts noted by the vehicle application should be replaced as needed during service. Verify the exhaust routing and OE part number 28600-3Q330 before installation. Part number 38017 is listed for the single exhaust configuration only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies OE replacement exhaust components built to match the listed application requirements. This part is specified as an original equipment replacement and uses aluminized steel for exhaust-system service.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507709109,"sku":"BBDL-38017","price":88.41,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38017_Fro.jpg?v=1774704127"},{"product_id":"ap-exhaust-38651-exhaust-pipe","title":"AP Exhaust 38651 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 38651 Exhaust Pipe Overview\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38651 is an aluminized steel exhaust pipe made as an original equipment replacement for select GM full-size SUVs. It is built for center exhaust routing on 1996-2000 Chevrolet Tahoe, 1996-2000 GMC Yukon, and 1999-2000 Cadillac Escalade applications with OE welded-system layouts.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a 1996-2000 Chevrolet Tahoe center exhaust pipe or a 1999-2000 GMC Yukon OE replacement exhaust pipe, this part number provides a direct-fit service option for the listed vehicles. AP Exhaust 38651 is also a relevant match for 1999-2000 Cadillac Escalade center exhaust service.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for corrosion resistance in exhaust service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eCenter exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eBuilt for OE welded assembly layouts noted in the fitment data\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chevrolet Tahoe, center\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC Yukon, center\u003c\/li\u003e\n\u003cli\u003eFits 1999-2000 GMC Yukon, center\u003c\/li\u003e\n\u003cli\u003eFits 1999-2000 Cadillac Escalade, center\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38651 is an OE-style exhaust pipe for center-position service on select Chevrolet Tahoe, GMC Yukon, and Cadillac Escalade models. The aluminized steel material is commonly used in exhaust replacement parts because it balances durability and cost for underbody exhaust routing. This part number is intended for vehicles listed with welded factory exhaust assemblies, where matching the original routing and connection style is important for proper service fitment.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated center exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after damage to the original welded assembly\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks at the center section\u003c\/li\u003e\n\u003cli\u003eAddressing fitment issues on OE-style replacement exhaust service\u003c\/li\u003e\n\u003cli\u003eServicing a 1996-2000 Chevrolet Tahoe, 1996-2000 GMC Yukon, or 1999-2000 Cadillac Escalade exhaust system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and center-position application before ordering. The fitment notes indicate the OE system was a welded assembly and recommend replacing all parts noted [1] when servicing the system. Confirm the existing exhaust layout and connection points on the vehicle before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust manufactures this part as an original equipment replacement exhaust component for the listed applications. The aluminized steel construction supports standard exhaust replacement service on the specified GM SUVs.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385507905717,"sku":"BBDL-38651","price":107.93,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38651_Top_77a2ca10-1502-4e62-be4b-6576155609aa.jpg?v=1774704129"},{"product_id":"ap-exhaust-38657-exhaust-pipe","title":"AP Exhaust 38657 Exhaust Pipe - Center or Front","description":"\u003ch2\u003eAP Exhaust 38657 Exhaust Pipe for Suburban Applications\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38657 is an aluminized steel exhaust pipe built as an original equipment replacement for select Chevrolet and GMC Suburban models. It is specified for front and center exhaust positions on 1996-1999 applications, including Federal Emissions configurations where noted.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement part\u003c\/li\u003e\n\u003cli\u003eFits front and center exhaust positions, depending on application\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Chevrolet Suburban and GMC Suburban fitments\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 38657\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is intended for owners replacing a worn, rusted, or damaged OE pipe on 1996-1999 Chevrolet C1500 Suburban, C2500 Suburban, K1500 Suburban, and K2500 Suburban models, as well as GMC C1500 Suburban, C2500 Suburban, K1500 Suburban, and K2500 Suburban models. The aluminized steel material provides a practical OE-style service replacement for exhaust routing on these Suburban platforms. AP Exhaust 38657 is a direct-fit replacement choice for restoring proper exhaust flow and maintaining the original system layout where the factory exhaust was a welded assembly.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrosion or rust-through in the exhaust pipe\u003c\/li\u003e\n\u003cli\u003eCracks or leaks in the original welded exhaust assembly\u003c\/li\u003e\n\u003cli\u003eExhaust noise caused by a damaged pipe section\u003c\/li\u003e\n\u003cli\u003eRestricted exhaust flow from a deteriorated pipe\u003c\/li\u003e\n\u003cli\u003eReplacement needs on Federal Emissions Suburban applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and exhaust position before ordering. Fitment includes front and center locations, and several applications note that the OE system was a welded assembly; those parts should be replaced as specified for the vehicle. Confirm the correct Suburban configuration before installation to ensure the pipe matches the original routing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38657 is an OE replacement exhaust pipe made from aluminized steel for service on select Chevrolet and GMC Suburban applications. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385508102325,"sku":"BBDL-38657","price":72.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38657_Top_785a8a53-255b-41ca-8385-5b98aaea4f81.jpg?v=1774704129"},{"product_id":"ap-exhaust-38660-exhaust-pipe","title":"AP Exhaust 38660 Exhaust Pipe - Center or Front","description":"\u003ch2\u003eOE Replacement Exhaust Pipe for Buick and Pontiac\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38660 is an aluminized steel exhaust pipe built as an original equipment replacement for select Buick and Pontiac applications. It is listed for center and front positions on single-exhaust systems, including 1997-2005 Buick Century and 1997-2002 Pontiac Grand Prix, with a 2003 Pontiac Grand Prix front application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eFits center and front exhaust pipe locations\u003c\/li\u003e\n\u003cli\u003eDirect application for select Buick Century and Pontiac Grand Prix models\u003c\/li\u003e\n\u003cli\u003eAP Exhaust part number 38660\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis exhaust pipe is made to replace the factory pipe in OE-style exhaust layouts where the original system used a welded assembly. AP Exhaust 38660 serves as a direct replacement for 1997-2005 Buick Century, center; 1997-2002 Pontiac Grand Prix, center; and 2003 Pontiac Grand Prix, front. The aluminized steel material is commonly used in exhaust service for its corrosion-resistant properties in everyday driving conditions. If you are searching for an aluminized steel exhaust pipe for a 1997-2005 Buick Century or a 1997-2002 Pontiac Grand Prix exhaust repair, this part number is a direct match for the listed applications.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated factory exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRestoring exhaust flow after a welded OE pipe failure\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks at the center or front section\u003c\/li\u003e\n\u003cli\u003eAddressing noise from a damaged single-exhaust pipe\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to OE-style routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eReview the vehicle-specific notes before installation. The OE system was a welded assembly, and AP Exhaust recommends replacing all parts noted in the application listing when servicing the system. Confirm the correct position before ordering or installing AP Exhaust 38660 on your Buick Century or Pontiac Grand Prix.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38660 is an original equipment replacement exhaust pipe built to match the listed factory applications for fit and function.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385508135093,"sku":"BBDL-38660","price":77.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38660_Top.jpg?v=1774704129"},{"product_id":"ap-exhaust-38732-exhaust-pipe","title":"AP Exhaust 38732 Exhaust Pipe - Center","description":"\u003ch2\u003eAP Exhaust 38732 Exhaust Pipe for Dakota\u003c\/h2\u003e\u003cp\u003eAP Exhaust 38732 is an aluminized steel exhaust pipe built as an original equipment replacement for select Dodge Dakota applications. It is listed for center-position fitment on 2000-2003 Dodge Dakota Club Cab models and 2001-2002 Dodge Dakota applications, giving buyers a direct-match option for common exhaust repair needs.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eAluminized steel construction for exhaust system service\u003c\/li\u003e\n\u003cli\u003eOriginal equipment replacement design\u003c\/li\u003e\n\u003cli\u003eCenter-position exhaust pipe application\u003c\/li\u003e\n\u003cli\u003eFits select Dodge Dakota models from 2000-2003\u003c\/li\u003e\n\u003cli\u003ePart number 38732 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eFits 2000-2003 Dodge Dakota, center, Club Cab. Fits 2001-2002 Dodge Dakota, N\/A.\u003c\/p\u003e\u003cp\u003eThis AP Exhaust 38732 exhaust pipe is a direct replacement choice for Dodge Dakota owners addressing corrosion, leaks, or damaged factory piping. The aluminized steel material is commonly used in exhaust service for its balance of durability and value, and the OE replacement format supports a factory-style repair on the listed Dakota configurations. AP Exhaust 38732 is a practical match when replacing a worn center exhaust pipe on the specified Dodge Dakota years.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a rusted or perforated exhaust pipe\u003c\/li\u003e\n\u003cli\u003eRepairing exhaust leaks that create noise or odor\u003c\/li\u003e\n\u003cli\u003eRestoring proper exhaust routing after pipe damage\u003c\/li\u003e\n\u003cli\u003eAddressing failed factory pipe sections on a Dodge Dakota\u003c\/li\u003e\n\u003cli\u003eReturning the exhaust system to OE-style layout\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, body configuration, and exhaust position before ordering. Confirm center-position routing on the 2000-2003 Dodge Dakota Club Cab and the listed 2001-2002 Dodge Dakota application to ensure correct match-up with the existing exhaust system. Professional exhaust installation practices are recommended for proper alignment and sealing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAP Exhaust supplies OE replacement exhaust components, and part number 38732 is cataloged for the listed Dodge Dakota fitments. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"AP Exhaust","offers":[{"title":"Default Title","offer_id":43385508561077,"sku":"BBDL-38732","price":30.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/AP_38732_Top_96cf822a-c12b-4f53-99f2-71b740fdded1.jpg?v=1774704131"}],"url":"https:\/\/www.partcatalog.com\/collections\/exhaust-and-tail-pipes.oembed?page=31","provider":"PartCatalog","version":"1.0","type":"link"}