{"title":"Body \u003e Glass, Windows and Related Components","description":"\u003cp\u003eThis collection covers the hardware and structural components that keep your vehicle's glass panels operating correctly and sealed in place. The bulk of the 306 parts here are \u003cstrong\u003eback glass lift supports\u003c\/strong\u003e — the gas-charged struts that hold your hatchback, SUV liftgate, or rear window open while you load cargo. These typically last 5–10 years before the nitrogen charge bleeds out and they can no longer hold weight. The remaining parts — window guides, channels, latches, attaching clips, and windshield trim — are the smaller but critical pieces that control how door and vent glass travels, seals, and locks. When buying lift supports, match the extended and compressed length and the Newton force rating to your OEM spec; an undersized strut will drift shut, an oversized one can stress the glass or hinge. For guides and channels, rubber durometer and exact channel dimensions matter more than brand.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLiftgate or rear hatch slowly drifts down\u003c\/strong\u003e after you open it — the classic sign of a worn back glass lift support that's lost gas pressure and can no longer hold the rated load.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRear window or hatch slams shut suddenly\u003c\/strong\u003e rather than lowering gradually, indicating a support has failed completely and provides no dampening resistance.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDoor glass drops, rattles, or sits at an angle\u003c\/strong\u003e in the door frame — often caused by a cracked window guide, failed attaching clip, or degraded window channel that's no longer holding the glass on track.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVent or sliding window won't stay latched\u003c\/strong\u003e shut, letting in wind noise, water, or rattling at highway speed — the latch mechanism is worn or the striker is misaligned.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWhistling or wind noise from the windshield area\u003c\/strong\u003e at speed can point to deteriorated windshield post trim that's no longer creating a proper seal between the A-pillar and glass edge.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVisible rust, cracking, or collapsed rubber\u003c\/strong\u003e on a window channel or guide — even without functional symptoms yet, degraded rubber accelerates glass wear and can allow water intrusion into the door.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHow long do back glass lift supports last, and do they need to be replaced in pairs?\u003c\/strong\u003e\n  Most lift supports last 5–10 years or 80,000–120,000 miles depending on climate and use frequency. Always replace both supports at the same time — if one has failed, the other is under the same stress and is close behind. Mismatched support strength will cause uneven lift and can strain the hinge or glass.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eAre aftermarket lift supports as reliable as OEM, and what specs should I check?\u003c\/strong\u003e\n  Quality aftermarket supports from brands like Stabilus, Suspa, or StrongArm are generally comparable to OEM and often cost 40–60% less. The critical specs are extended length, compressed length, and force rating in Newtons — these must match your application. Avoid no-name units with unspecified force ratings; an incorrect force value is the most common cause of early failure or poor fitment.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat does back glass lift support replacement cost, and is it a reasonable DIY job?\u003c\/strong\u003e\n  Parts run roughly $15–$45 per strut for aftermarket, $40–$90 each for OEM. Most hatchback and SUV applications are straightforward 15–30 minute DIY jobs requiring only a trim tool and possibly a socket — no special tools needed. On some luxury SUVs with power liftgates, a calibration reset via scan tool may be required after replacement.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"dorman-76985-sliding-window-latch","title":"Dorman 76985 Sliding Window Latch","description":"\u003ch2\u003eDorman 76985 Sliding Window Latch\u003c\/h2\u003e\u003cp\u003eDorman 76985 is a sliding window latch built to match the fit and function of the original latch on specified vehicles. It uses metal and plastic construction with a black finish for a direct replacement on compatible Chevrolet and GMC trucks.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style sliding window latch for specified applications\u003c\/li\u003e\n\u003cli\u003eMetal and plastic construction for durable, reliable operation\u003c\/li\u003e\n\u003cli\u003eBlack finish for a factory-style appearance\u003c\/li\u003e\n\u003cli\u003eBolt-on attachment type for secure mounting\u003c\/li\u003e\n\u003cli\u003ePackage contents: latch and plate\u003c\/li\u003e\n\u003cli\u003eCross-reference part number: 769851\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis sliding window latch is engineered for Chevrolet C1500, C2500, C3500, K1500, K2500, and K3500 trucks, as well as GMC C1500, C2500, C3500, K1500, K2500, and K3500 trucks across 1988-1994 model years. It is designed to restore the original latch fit and function on vehicles with a 4-piece window configuration where noted, making it a direct replacement for worn or damaged hardware. Part number 76985 also cross-references 15616252 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBroken or cracked sliding window latch hardware\u003c\/li\u003e\n\u003cli\u003eLoose latch engagement on rear or side sliding windows\u003c\/li\u003e\n\u003cli\u003eDifficulty securing the sliding window in the closed position\u003c\/li\u003e\n\u003cli\u003eWorn original latch components that no longer hold properly\u003c\/li\u003e\n\u003cli\u003eFactory-style replacement needs on Chevrolet and GMC truck glass assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1994 Chevrolet C1500, N\/A, 4 Piece Window; 1994 Chevrolet C2500, N\/A, 4 Piece Window; 1994 Chevrolet C3500, N\/A, 4 Piece Window; 1994 Chevrolet K1500, N\/A, 4 Piece Window; 1994 Chevrolet K2500, N\/A, 4 Piece Window; 1994 Chevrolet K3500, N\/A, 4 Piece Window; 1994 GMC C1500, N\/A, 4 Piece Window; 1994 GMC C2500, N\/A, 4 Piece Window; 1994 GMC C3500, N\/A, 4 Piece Window; 1994 GMC K1500, N\/A, 4 Piece Window; 1994 GMC K2500, N\/A, 4 Piece Window; 1994 GMC K3500, N\/A, 4 Piece Window. Fits 1988-1993 Chevrolet C1500, N\/A; 1988-1993 Chevrolet C2500, N\/A; 1988-1993 Chevrolet C3500, N\/A; 1988-1993 Chevrolet K1500, N\/A; 1988-1993 Chevrolet K2500, N\/A; 1988-1993 Chevrolet K3500, N\/A; 1988-1993 GMC C1500, N\/A; 1988-1993 GMC C2500, N\/A; 1988-1993 GMC C3500, N\/A; 1988-1993 GMC K1500, N\/A; 1988-1993 GMC K2500, N\/A; 1988-1993 GMC K3500, N\/A. Verify the existing window hardware and mounting points before installation. Mounting hardware is not included.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this latch to match original fit and function while using durable materials for dependable service in the specified Chevrolet and GMC truck applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43415315513525,"sku":"BCZF-76985","price":21.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_76985_Fro.jpg?v=1774731185"},{"product_id":"dorman-76989-sliding-window-latch","title":"Dorman 76989 Sliding Window Latch","description":"\u003ch2\u003eSliding Window Latch for OE-Style Fit\u003c\/h2\u003e\u003cp\u003eDorman 76989 is a black plastic sliding window latch built to match the fit and function of the original latch on specified vehicles. It is designed for durable, reliable operation on classic Ford trucks and Dodge Ram models with sliding rear window assemblies.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement sliding window latch for factory-style operation\u003c\/li\u003e\n\u003cli\u003eBlack plastic construction for a clean, original-equipment appearance\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment for direct mounting\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for installation\u003c\/li\u003e\n\u003cli\u003ePackage contents: latch, keeper, spacers, and screws\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman sliding window latch, part number 76989, is engineered to restore secure closure and smooth latching action on compatible rear sliding windows. It is a direct-fit replacement for applications such as Ford F-150, Ford F-250, Ford F-350, Ford Ranger, Ford F-100, and Dodge Ram 1500, Ram 2500, and Ram 3500 models listed below. This part cross-references 769891 and E0TZ1040860A for the same application.\u003c\/p\u003e\u003cp\u003eBuilt from plastic with a black finish, Dorman 76989 is made for vehicles where the original latch has cracked, worn, or no longer holds the window securely. The screw-on design and included keeper, spacers, and screws support a straightforward replacement on the sliding window assembly.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1994-2002 Dodge Ram 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1994-2002 Dodge Ram 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1994-2001 Dodge Ram 1500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1980-1994 Ford F-150, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1980-1994 Ford F-250, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1980-1994 Ford F-350, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1983-1993 Ford Ranger, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1980-1983 Ford F-100, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBroken or cracked sliding window latch\u003c\/li\u003e\n\u003cli\u003eWindow that will not stay securely closed\u003c\/li\u003e\n\u003cli\u003eLoose or worn latch engagement on the rear sliding glass\u003c\/li\u003e\n\u003cli\u003eMissing or damaged original latch hardware\u003c\/li\u003e\n\u003cli\u003eDifficulty securing the sliding rear window on Ford and Dodge truck applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eUse the screw-on mounting points and supplied keeper, spacers, and screws to replace the existing latch assembly. Before installation, compare the original latch shape, mounting pattern, and window alignment to confirm proper placement on the sliding glass assembly. For best results, inspect the keeper contact point and tighten fasteners evenly so the latch engages smoothly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this replacement latch to match original fit and function on specified vehicles, with a focus on durability and dependable performance. Part number 76989 is built as a direct replacement for factory-style sliding window service on compatible Ford and Dodge truck applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43415315579061,"sku":"BCZF-76989","price":21.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_76989_Fro.jpg?v=1774731185"},{"product_id":"strongarm-4139-back-glass-lift-support","title":"StrongArm 4139 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4139 Back Glass Lift Support for Excursion\u003c\/h2\u003e\u003cp\u003eStrongArm 4139 is a specific-fit back glass lift support for the 2000-2005 Ford Excursion. It uses a pressurized cylinder design to help hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for Ford Excursion rear glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 9.97 in.; extended length: 14.72 in.; stroke length: 4.75 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 142.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with nylon 10 mm ball socket ends\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smoother operation and wear resistance\u003c\/li\u003e\n\u003cli\u003eStrongArm 4139 cross-references AMS Automotive 4139 and OE-style numbers including E4139 and YC3Z 78406A10-AA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis StrongArm back glass lift support is built for the rear window glass on 2000-2005 Ford Excursion models. The StrongArm 4139 part number is a direct reference for this application, and the specific-fit design helps match the original mounting style and operating length needed for proper rear glass support.\u003c\/p\u003e\u003cp\u003eCompatible With: Fits 2000-2005 Ford Excursion, N\/A. Search terms such as Ford Excursion back glass lift support, rear window glass strut, and StrongArm 4139 Ford Excursion are commonly used for this part.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or weak lift support action\u003c\/li\u003e\n\u003cli\u003eHatch glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window support\u003c\/li\u003e\n\u003cli\u003eWorn pressurized cylinder performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke, and 10 mm ball socket end type before installation. Inspect the mounting points on the Ford Excursion rear glass and body for wear or damage, and confirm the support moves smoothly through its travel after installation. For proper operation and balanced support, replace lift supports in pairs when servicing the rear glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. The steel cylinder construction, nylon socket ends, and Teflon-based materials support consistent performance in rear glass applications such as the Ford Excursion.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613157523637,"sku":"BBZN-4139","price":17.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4139_Fro.jpg?v=1774984260"},{"product_id":"strongarm-4185-back-glass-lift-support","title":"StrongArm 4185 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for GM SUVs\u003c\/h2\u003e\u003cp\u003eRestore smooth rear window operation with this StrongArm back glass lift support, part number 4185. It is a specific-fit gas strut engineered for rear glass applications on select Cadillac, Chevrolet, and GMC SUVs, including Escalade, Suburban, Tahoe, and Yukon models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.06 in.; compressed length: 11.31 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.75 in. for controlled opening and closing movement\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 45.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: 10 mm nylon on one end, 8 mm nylon on the other\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4185 is a pressurized lift support built for rear glass service on compatible GM utility vehicles. The cylinder measures 15.0 mm outside diameter with a 6.0 mm inner shaft diameter, and its specific-fit design helps maintain proper alignment and consistent support for the back glass. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 2000 Cadillac Escalade, 2000-2006 Chevrolet Suburban 1500, 2000-2006 Chevrolet Suburban 2500, 2000-2006 Chevrolet Tahoe, 2000-2006 GMC Yukon, 2000-2006 GMC Yukon XL 1500, 2000-2006 GMC Yukon XL 2500, 2002-2006 Cadillac Escalade, 2002-2006 Cadillac Escalade EXT, and 2003-2006 Cadillac Escalade ESV. StrongArm part number 4185 is a direct-fit option for rear glass support service on these vehicles.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eBack window that is difficult to raise or lower\u003c\/li\u003e\n\u003cli\u003eUneven support or poor holding force at the hatch glass\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn gas strut\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the end fittings and extended\/compressed lengths before installation. Match the vehicle application carefully, especially on Cadillac Escalade, Chevrolet Tahoe, and GMC Yukon rear glass service. For proper operation, replace lift supports in pairs when servicing the rear glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life in automotive applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613164896437,"sku":"BBZN-4185","price":18.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4185_Fro.jpg?v=1774984270"},{"product_id":"strongarm-4187-back-glass-lift-support","title":"StrongArm 4187 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Mazda Tribute\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4187. It is a specific-fit replacement for 2001-2006 Mazda Tribute models and is built as a pressurized cylinder for steady support of the rear window glass.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 2001-2006 Mazda Tribute\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.42 in.; extended length: 17.92 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.5 in. for rear glass lift travel\u003c\/li\u003e\n\u003cli\u003e40.0 maximum force rating\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003e10 mm nylon ball socket ends on both sides\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4187 is engineered for rear window glass support on the Mazda Tribute, using a pressurized cylinder design to help hold the liftglass in position during opening and closing. The specific-fit design matches the 2001, 2002, 2003, 2004, 2005, and 2006 Mazda Tribute, making it a direct replacement choice for rear glass lift support service. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Addresses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support response\u003c\/li\u003e\n\u003cli\u003eBack glass that feels heavy or difficult to raise\u003c\/li\u003e\n\u003cli\u003eLoss of support pressure in the rear hatch glass\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window opening action\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, and 10 mm ball socket end style before installation on your Mazda Tribute. Inspect the mounting points and ball studs for wear or damage before replacing the support. Rear glass lift supports are commonly serviced in pairs to maintain balanced operation and reliable support.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life. Part number 4187 is built for specific-fit application coverage on the Mazda Tribute rear glass.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613164929205,"sku":"BBZN-4187","price":16.71,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4187_Fro.jpg?v=1774984271"},{"product_id":"strongarm-4188-back-glass-lift-support","title":"StrongArm 4188 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Toyota Matrix\u003c\/h2\u003e\u003cp\u003eStrongArm 4188 is a specific-fit back glass lift support for the 2003-2008 Toyota Matrix. It uses a pressurized cylinder design to hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit design for the 2003-2008 Toyota Matrix\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.37 in.; compressed length: 10.87 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.5 in. for rear glass travel\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 16-degree on one end, nylon 10 mm on the other\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 31.0\u003c\/li\u003e\n\u003cli\u003eStrongArm 4188 replacement part number for rear window glass support service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4188 is engineered as a back glass lift support for the Toyota Matrix rear window glass. The cylinder is built with a steel outer body and internal materials selected for smooth operation and long service life, while the specific-fit design helps ensure proper alignment at the hatch glass mounting points. This part number, 4188, is a direct replacement option for 2003-2008 Toyota Matrix models and is commonly searched as a Toyota Matrix rear glass lift support, hatch glass strut, or rear window support strut.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4188 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or weak hatch glass lift action\u003c\/li\u003e\n\u003cli\u003eDrooping back window glass on a Toyota Matrix\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass support\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle application before installation and match the end fittings to the original support. For proper rear glass operation, replace lift supports in pairs so the hatch glass opens and holds evenly. Confirm the compressed and extended lengths, stroke, and ball socket style against the original part before final installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer-lasting performance. StrongArm 4188 is built for direct-fit service on the Toyota Matrix rear glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613164961973,"sku":"BBZN-4188","price":19.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4188_Fro.jpg?v=1774984271"},{"product_id":"strongarm-4190-back-glass-lift-support","title":"StrongArm 4190 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Rear Defroster Applications\u003c\/h2\u003e\u003cp\u003eRestore controlled opening and holding force for the rear window glass with this StrongArm back glass lift support. StrongArm Part Number 4190 is a specific-fit gas strut engineered for rear glass applications on select Chevrolet and GMC SUVs and Suburban models with rear defrosters.\u003c\/p\u003e\u003cp\u003eBuilt with a black steel outer cylinder, rubber and Teflon materials, and nylon electric-style ball socket ends, this lift support is specified for smooth operation and consistent support. The 85.0 maximum force rating, 16.25 extended length, and 4.25 stroke length are matched to the listed rear glass applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStrongArm Part Number 4190 back glass lift support\u003c\/li\u003e\n\u003cli\u003eSpecific-fit design for listed rear window glass applications\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable construction\u003c\/li\u003e\n\u003cli\u003eBall socket ends on both sides for the correct mounting style\u003c\/li\u003e\n\u003cli\u003e16.25 extended length, 12.0 compressed length, and 4.25 stroke length\u003c\/li\u003e\n\u003cli\u003e85.0 maximum force for rear glass support\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating consistency\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4190 is a rear glass lift support made for vehicles that use a rear window defroster and the specified mounting arrangement. It is listed for 1992-1994 Chevrolet Blazer, 1992-1994 Chevrolet C1500 Suburban, 1992-1994 Chevrolet C2500 Suburban, 1992-1994 Chevrolet K1500 Suburban, 1992-1994 Chevrolet K2500 Suburban, 1992-1994 GMC C1500 Suburban, 1992-1994 GMC C2500 Suburban, 1992-1994 GMC K1500 Suburban, 1992-1994 GMC K2500 Suburban, and 1992-1994 GMC Yukon, with notes for rear defroster-equipped applications and first-design rear glass setups where specified.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts 172286 and 182286 for the same application. StrongArm engineers its lift supports to meet demanding automotive use, and the specific-fit design helps ensure the correct length, force, and end fittings for the listed Chevrolet Blazer, Suburban, and GMC Yukon rear glass applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support action\u003c\/li\u003e\n\u003cli\u003eDrooping hatch glass on rear defroster-equipped vehicles\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window opening effort\u003c\/li\u003e\n\u003cli\u003eNoise or instability from worn gas struts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and rear glass configuration before ordering. This StrongArm 4190 is a specific-fit part, so the end style, compressed length, extended length, and force rating should match the original application. For safe and reliable rear glass support, replace lift supports in pairs when servicing the vehicle.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Part Number 4190 is built for the listed rear glass applications on Chevrolet and GMC vehicles with rear defrosters.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613165027509,"sku":"BBZN-4190","price":25.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4190_Fro.jpg?v=1774984271"},{"product_id":"strongarm-4191-back-glass-lift-support","title":"StrongArm 4191 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4191 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with the StrongArm 4191 back glass lift support. This specific-fit lift support is engineered for 2003-2006 Ford Expedition and 2003-2006 Lincoln Navigator rear window glass applications, with smooth operation and dependable holding force.\u003c\/p\u003e\u003cp\u003eBuilt with a black steel outer cylinder, rubber and Teflon materials, and nylon 10mm ball socket ends, this StrongArm lift support is sized for direct replacement use on the rear glass. The 43.0 maximum force rating, 18.38 extended length, and 12.88 compressed length help deliver consistent support for the back glass on Ford Expedition and Lincoln Navigator models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eFits 2003-2006 Ford Expedition and 2003-2006 Lincoln Navigator\u003c\/li\u003e\n\u003cli\u003ePart number 4191 for direct application matching\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder construction\u003c\/li\u003e\n\u003cli\u003eNylon 10mm ball socket ends on both sides\u003c\/li\u003e\n\u003cli\u003e18.38 extended length and 12.88 compressed length\u003c\/li\u003e\n\u003cli\u003e5.5 stroke length with 43.0 maximum force\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon material construction for smoother movement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4191 is a back glass lift support made for rear window glass service on the Ford Expedition and Lincoln Navigator. It is a specific-fit replacement, not a universal support, and its dimensions and end fittings are matched to the listed vehicle applications. The pressurized cylinder design helps hold the rear glass in position while allowing controlled opening and closing action.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application. If you are replacing a worn rear glass support on a 2003-2006 Ford Expedition or 2003-2006 Lincoln Navigator, part number 4191 provides the fitment and hardware style needed for the original mounting points.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window glass that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eBinding or rough rear glass movement\u003c\/li\u003e\n\u003cli\u003eNoise or instability when opening the rear glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, and model before ordering. Confirm the existing mounting style uses 10mm nylon ball socket ends and compare the compressed and extended lengths to the original support. For proper rear glass support and balanced operation, replace lift supports in pairs when servicing the liftgate glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to support smoother operation and longer service life in automotive applications. Part number 4191 is built for the specified Ford Expedition and Lincoln Navigator rear glass fitment.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613165060277,"sku":"BBZN-4191","price":19.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4191_Fro.jpg?v=1774984272"},{"product_id":"strongarm-4192-back-glass-lift-support","title":"StrongArm 4192 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4192 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4192 is a specific-fit back glass lift support for the 2001-2006 Hyundai Santa Fe. It uses a pressurized cylinder to hold rear window glass in the open position and provide controlled movement during opening and closing.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit design for the 2001-2006 Hyundai Santa Fe\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.14 in.; compressed length: 10.99 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.15 in. for rear glass movement\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 24.0\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis StrongArm 4192 lift support is engineered for rear window glass service on the Hyundai Santa Fe. The pressurized cylinder helps maintain liftgate glass position while opening and closing, and the specific-fit design supports direct replacement on 2001, 2002, 2003, 2004, 2005, and 2006 Hyundai Santa Fe models. StrongArm manufactures lift supports beyond industry standards for smoother operation and longer service life. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 901719) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven liftgate glass movement\u003c\/li\u003e\n\u003cli\u003eWeak support when opening the back window\u003c\/li\u003e\n\u003cli\u003eDropping rear glass during service or loading\u003c\/li\u003e\n\u003cli\u003eLoss of controlled motion from worn gas struts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the ball socket end style and length before installation on your Hyundai Santa Fe. Replace lift supports in pairs when servicing the rear glass system to maintain balanced operation and consistent support. Confirm the mounting points and fitment against the vehicle before removal of the original support.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm builds this lift support as a specific-fit replacement for the listed Hyundai Santa Fe applications, with construction focused on smooth operation and durable performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613165912245,"sku":"BBZN-4192","price":21.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4192_Fro.jpg?v=1774984272"},{"product_id":"strongarm-4193-back-glass-lift-support","title":"StrongArm 4193 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Mitsubishi Endeavor\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4193. It is a specific-fit pressurized cylinder engineered for the 2004-2008 Mitsubishi Endeavor rear window glass, with smooth operation and consistent support for daily use.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the Mitsubishi Endeavor\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.05 in.; compressed length: 10.45 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.6 in. for rear glass lift travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 37.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003e10 mm nylon ball socket ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating consistency\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4193 is built as a rear window glass lift support for 2004-2008 Mitsubishi Endeavor models. The pressurized cylinder helps hold the back glass in the open position and provides controlled movement when opening or closing the liftglass. With a specific fit design, this part number 4193 matches the application requirements for the Mitsubishi Endeavor rear glass support system.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow liftgate glass movement\u003c\/li\u003e\n\u003cli\u003eUneven support when opening the back window glass\u003c\/li\u003e\n\u003cli\u003eLoss of pressure in the original lift support\u003c\/li\u003e\n\u003cli\u003eDifficulty holding the rear glass in the raised position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible With 2004-2008 Mitsubishi Endeavor rear glass applications. Verify the 10 mm ball socket attachment points and compare compressed and extended length before installation. Replace lift supports in pairs when the vehicle uses matching supports on both sides of the rear glass for balanced operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Part number 4193 is built for specific-fit use on the Mitsubishi Endeavor rear glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613166174389,"sku":"BBZN-4193","price":21.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4193_Fro.jpg?v=1774984272"},{"product_id":"strongarm-4219-back-glass-lift-support","title":"StrongArm 4219 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Astro and Safari\u003c\/h2\u003e\u003cp\u003eStrongArm 4219 is a specific-fit back glass lift support for select Chevrolet Astro and GMC Safari models. It uses a pressurized cylinder design to help hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 21.22 in.; compressed length: 13.12 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 8.1 in. for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 107.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eThreaded (8mm) end 1 and 10mm nylon ball socket end 2\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating consistency\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4219 is engineered for rear glass lift applications on 1992-2000 Chevrolet Astro and 1992-2000 GMC Safari models. As a back glass lift support, it helps maintain the rear window in the raised position while providing controlled lift and lowering action. The specific-fit design supports accurate replacement on the intended vehicle applications, and the 107.0 force rating matches the needs of the rear glass assembly. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support operation\u003c\/li\u003e\n\u003cli\u003eHatch glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the end fittings before installation: threaded (8mm) on one end and a 10mm nylon ball socket on the other. Confirm vehicle application by year, make, and model before ordering. For rear glass service, inspect the mounting points and surrounding hardware for wear or damage before installing the replacement support.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. For fitment-focused searches, this StrongArm 4219 back glass lift support is a direct replacement option for 1992-2000 Chevrolet Astro and 1992-2000 GMC Safari rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613170237621,"sku":"BBZN-4219","price":19.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4219_Fro.jpg?v=1774984276"},{"product_id":"strongarm-4249-back-glass-lift-support","title":"StrongArm 4249 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4249 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4249 is a specific-fit back glass lift support for 1997-2006 Jeep TJ and 1997-2006 Jeep Wrangler applications. It uses a pressurized cylinder design to hold rear window glass in position and deliver controlled opening and closing action.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for Jeep TJ and Jeep Wrangler\u003c\/li\u003e\n\u003cli\u003eExtended length: 25.39 in.; compressed length: 14.57 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 10.82 in. with 33.0 maximum force\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smoother operation and wear resistance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBuilt for rear glass support service, StrongArm 4249 is engineered for the back glass on 1997-2006 Jeep TJ and 1997-2006 Jeep Wrangler models. The pressurized cylinder helps maintain liftgate glass position while providing consistent motion during opening and closing. This part number 4249 is a direct-fit replacement for the listed Jeep applications and is also referenced by cross numbers such as Monroe Shocks \u0026amp; Struts 172286 and 182286 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support movement\u003c\/li\u003e\n\u003cli\u003eBack glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent hatch glass operation\u003c\/li\u003e\n\u003cli\u003eNoise or binding from worn lift support hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the ball socket end style and compressed\/extended length before installation. This StrongArm 4249 back glass lift support is a specific-fit part for the listed Jeep TJ and Jeep Wrangler model years, so confirm vehicle application by year and model before replacement. For safe, reliable rear glass support, replace lift supports in pairs when the vehicle uses matched supports.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards to support smoother operation and longer service life. The 4249 is built with a steel outer cylinder, nylon ball socket ends, and wear-resistant materials selected for consistent performance in automotive rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613174988981,"sku":"BBZN-4249","price":19.85,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4249_Fro.jpg?v=1774984279"},{"product_id":"strongarm-4294-back-glass-lift-support","title":"StrongArm 4294 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Honda CR-V\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support for the 1997-2001 Honda CR-V. Part number 4294 is a specific-fit replacement built for smooth operation and dependable support of the rear window glass.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 1997-2001 Honda CR-V\u003c\/li\u003e\n\u003cli\u003eCompressed length: 16.25 in.; extended length: 21.25 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.0 in. with 42.0 maximum force\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket nylon 10mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for consistent movement\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 4294\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4294 is a rear window glass lift support engineered for the Honda CR-V rear glass application. It uses a pressurized cylinder design to help hold the back glass in position and provide controlled opening and closing action. The steel outer cylinder, nylon ball socket ends, and internal rubber and Teflon materials support steady operation and long service life in daily use. This part cross-references AMS Automotive 4294 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eSlow, uneven, or jerky rear hatch glass movement\u003c\/li\u003e\n\u003cli\u003eDifficulty opening the back glass on a Honda CR-V\u003c\/li\u003e\n\u003cli\u003eNoise or reduced control from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible With 1997-2001 Honda CR-V rear glass applications. Verify the compressed length, extended length, and 10mm ball socket end style before installation. Replace the support in pairs when servicing the rear glass system to maintain balanced operation and reliable hold-open performance. Confirm the mounting points are clean and undamaged before attaching the new support.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer-lasting performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613190029493,"sku":"BBZN-4294","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4294_Fro.jpg?v=1774984287"},{"product_id":"strongarm-4316-back-glass-lift-support","title":"StrongArm 4316 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Dropgate Applications\u003c\/h2\u003e\u003cp\u003eStrongArm 4316 is a specific-fit back glass lift support for select Chevrolet Blazer, GMC Jimmy, and Oldsmobile Bravada models with a dropgate. It uses a pressurized cylinder design to help hold rear window glass in the open position and deliver controlled movement during operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit rear glass lift support for targeted vehicle applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 19.01 in; compressed length: 11.45 in\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.56 in for measured opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 42.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 16 degree end and swivel eyelet end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation and wear resistance\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4316 back glass lift support is engineered for rear window glass service on 1995-2005 Chevrolet Blazer with dropgate, 1995-2001 GMC Jimmy with dropgate, and 1996-2001 Oldsmobile Bravada with dropgate. This part number 4316 is built as a specific-fit replacement, with dimensions and end fittings matched to the application for consistent rear glass support. StrongArm manufactures its lift supports to exceed typical industry standards for smoother operation and longer service life. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open on a Chevrolet Blazer, GMC Jimmy, or Oldsmobile Bravada\u003c\/li\u003e\n\u003cli\u003eSlow, weak, or uneven lift support movement at the back glass\u003c\/li\u003e\n\u003cli\u003eDropping rear window glass during loading or unloading\u003c\/li\u003e\n\u003cli\u003eExcess effort needed to raise or lower the dropgate glass\u003c\/li\u003e\n\u003cli\u003eWear-related loss of pressure in the original lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, make, model, and dropgate configuration before ordering. Confirm the end fittings and measured lengths against the original support to ensure proper alignment. For rear glass service, replace the support in pairs to maintain balanced operation and reliable holding force. Part number 4316 is a direct-fit style replacement for the listed applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to support smooth operation and long-lasting performance in automotive use. The pressurized cylinder construction, steel outer body, and application-specific fitment help deliver consistent rear glass support for the listed vehicles.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613194453173,"sku":"BBZN-4316","price":17.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4316_Fro.jpg?v=1774984290"},{"product_id":"strongarm-4320-back-glass-lift-support","title":"StrongArm 4320 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Pathfinder and QX4\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass operation with this StrongArm back glass lift support, part number 4320. It is a specific-fit gas strut engineered for the rear window glass on select Nissan Pathfinder and INFINITI QX4 models, with dimensions and end fittings matched to the application.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.91 in.; compressed length: 13.01 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.9 in. for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 42.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eEnd fittings: 10 mm nylon ball socket and blade end with .415 in. hole\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4320 is built for rear glass support on 1996-1999 Nissan Pathfinder and 1997-1999 INFINITI QX4 vehicles, with fitment listed through 12\/1998 for both models. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application. The StrongArm 4320 is also referenced by interchange part numbers including 510-802 and 900140.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eHatch glass that opens with reduced control\u003c\/li\u003e\n\u003cli\u003eNoise or binding during rear window movement\u003c\/li\u003e\n\u003cli\u003eLoss of support caused by worn gas strut seals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the end fittings and measurements before installation to confirm the correct rear glass lift support for your vehicle. Replace the support in pairs when servicing the rear glass system so the lift action remains balanced and consistent. Confirm the vehicle build date, since Pathfinder and QX4 fitment is listed to 12\/1998.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Part number 4320 is built as a specific-fit replacement for the listed Nissan Pathfinder and INFINITI QX4 rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613195501749,"sku":"BBZN-4320","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4320_Fro.jpg?v=1774984291"},{"product_id":"strongarm-4353-back-glass-lift-support","title":"StrongArm 4353 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4353 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4353 is a specific-fit back glass lift support for the 2001-2005 Pontiac Aztek. It restores controlled rear glass movement with a pressurized cylinder built for smooth operation and consistent support.\u003c\/p\u003e\u003cp\u003eUse this StrongArm back glass lift support when the rear window glass no longer stays open or moves with the same control as it should. The 4353 is engineered for direct fitment on Pontiac Aztek models from 2001 through 2005.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for Pontiac Aztek applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.07 in.\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.07 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.0 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force: 117.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003e10 mm nylon ball socket ends on both sides\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm Part Number 4353 is a rear window glass lift support engineered for the 2001-2005 Pontiac Aztek. It uses a pressurized cylinder design to help hold the back glass in position and provide smoother opening and closing action. With a 12.07-inch compressed length, 18.07-inch extended length, and 6.0-inch stroke, this support is built to match the specified rear glass application. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003cp\u003eStrongArm manufactures lift supports beyond standard industry requirements, with attention to consistent operation and long service life. The 4353 is a direct replacement choice for Pontiac Aztek rear glass service where the original support has weakened or lost pressure.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven liftgate glass movement\u003c\/li\u003e\n\u003cli\u003eLoss of support pressure in the back glass strut\u003c\/li\u003e\n\u003cli\u003eRear window glass that drops unexpectedly\u003c\/li\u003e\n\u003cli\u003eWorn or weak lift support performance on a Pontiac Aztek\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 2001-2005 Pontiac Aztek, rear glass position. Verify the 10 mm ball socket attachment points and overall length before installation. Replace the support in pairs when servicing the rear glass system to maintain balanced operation and reliable holding force.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed typical industry standards for smoother operation and longer-lasting performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613206020277,"sku":"BBZN-4353","price":17.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4353_Fro.jpg?v=1774984299"},{"product_id":"strongarm-4356-back-glass-lift-support","title":"StrongArm 4356 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Quest and Villager\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4356. It is a specific-fit pressurized cylinder engineered for the rear window glass on select Mercury Villager and Nissan Quest models from 1999-2002.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.05 in.; extended length: 19.05 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.0 in. with 36.0 maximum force\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable support performance\u003c\/li\u003e\n\u003cli\u003eNylon ball socket ends: 16-degree on one end, 8 mm on the other\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials used in the support assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm 4356 is a back glass lift support built for the rear window glass on the 1999-2002 Mercury Villager and 1999-2002 Nissan Quest. The pressurized cylinder helps hold the glass in position during opening and closing, while the specific-fit design supports consistent operation for the correct vehicle application. If you are replacing a worn rear hatch glass strut on a Mercury Villager or Nissan Quest, part number 4356 provides the fitment and dimensions needed for a direct replacement.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4356 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support movement\u003c\/li\u003e\n\u003cli\u003eBack glass that feels heavy or difficult to raise\u003c\/li\u003e\n\u003cli\u003eUneven support or inconsistent holding force\u003c\/li\u003e\n\u003cli\u003eNoise or loss of pressure from an aging lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle fitment before installation by matching the year, make, and model. Inspect the mounting points and ball sockets for wear before installing the new support. For best results, replace lift supports in pairs so the rear glass opens and closes with balanced support. Confirm the end fittings match the vehicle’s attachment points on the Mercury Villager or Nissan Quest before final installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that its lift supports are custom engineered and manufactured beyond industry standards to promote smoother operation and longer service life. Part number 4356 is built as a specific-fit replacement for the listed applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613206970549,"sku":"BBZN-4356","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4356_Fro.jpg?v=1774984300"},{"product_id":"strongarm-4365-back-glass-lift-support","title":"StrongArm 4365 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Jeep Liberty\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4365. It is a specific-fit gas strut engineered for the 2002-2007 Jeep Liberty rear window glass, with dimensions and end fittings matched to the application for consistent operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the Jeep Liberty\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.78 in.; compressed length: 11.02 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.76 in. for rear glass travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 40.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: 10 mm nylon on one end, 8 mm nylon on the other\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4365 is a rear window glass lift support built for 2002-2007 Jeep Liberty models. It uses a pressurized cylinder design to hold the back glass in position and provide smoother opening and closing action. The specific-fit construction, 15.0 mm cylinder outside diameter, and matched ball-socket end types help ensure proper alignment on the vehicle. This part cross-references Monroe Shocks \u0026amp; Struts 172286 and 182286 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eDifficulty opening or closing the rear glass\u003c\/li\u003e\n\u003cli\u003eWorn or noisy lift support operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2002-2007 Jeep Liberty, rear glass position. Verify the ball socket sizes and overall length before installation to confirm the correct replacement. Inspect the mounting points and surrounding hardware for wear or damage before attaching the new support. For proper rear glass control and balanced operation, replace lift supports in pairs when servicing the vehicle.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm manufactures this lift support beyond industry standards and custom engineers each unit for smoother operation and longer service life. Part number 4365 is built to meet the demands of daily rear glass use on the Jeep Liberty.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613209198773,"sku":"BBZN-4365","price":19.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4365_Fro.jpg?v=1774984303"},{"product_id":"strongarm-4372-back-glass-lift-support","title":"StrongArm 4372 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Explorer and Mountaineer\u003c\/h2\u003e\u003cp\u003eRestore controlled rear window glass movement with this StrongArm back glass lift support, part number 4372. It is built as a specific-fit replacement for 2002-2003 Ford Explorer and 2002-2003 Mercury Mountaineer applications with the listed production dates.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.19 in.; extended length: 17.69 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.5 in. for measured opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 67.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eNylon ball socket ends: 16 degree end 1 and 8 mm end 2\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation\u003c\/li\u003e\n\u003cli\u003ePart number 4372 for direct reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm 4372 is a pressurized lift support engineered for rear glass applications on the Ford Explorer and Mercury Mountaineer. It is designed around the listed dimensions and end fittings to match the original application, helping the back glass open and stay positioned with consistent resistance. This part cross-references AMS Automotive 4372 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 2002-2003 Ford Explorer, rear glass. Compatible With 2002-2003 Mercury Mountaineer, rear glass. Use part number 4372 when searching for a direct replacement back glass lift support for these vehicles.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support response\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent back window movement\u003c\/li\u003e\n\u003cli\u003eLoss of support pressure in the hatch glass area\u003c\/li\u003e\n\u003cli\u003eDifficulty opening or holding the rear window glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke, and ball socket end types before installation. Match the vehicle production date listed for your Explorer or Mountaineer to confirm fitment, and inspect the mounting points for wear before installing the new support. For consistent operation, replace lift supports in pairs when servicing the rear glass.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. Part number 4372 is built for specific-fit use on the listed Ford and Mercury applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613212770485,"sku":"BBZN-4372","price":17.78,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4372_Fro.jpg?v=1774984305"},{"product_id":"strongarm-4404-back-glass-lift-support","title":"StrongArm 4404 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Specific Fit Applications\u003c\/h2\u003e\u003cp\u003eStrongArm 4404 is a specific-fit back glass lift support for rear window glass applications that need controlled opening and steady hold position. It is engineered as a pressurized cylinder with steel construction and nylon ball socket ends for consistent operation on supported vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.0 in.; compressed length: 11.39 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.61 in. for controlled lift travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 38.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003e10 mm nylon ball socket ends on both sides\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4404 is built for rear glass support on a range of GM and Buick\/Pontiac applications, including Chevrolet S10 Blazer, GMC Jimmy, GMC S15 Jimmy, Buick Regal, Chevrolet Malibu, Oldsmobile Custom Cruiser, Pontiac Bonneville, Buick Century, Pontiac Grand LeMans, and Pontiac LeMans. This part number 4404 is engineered to match the specified application with the correct length, stroke, and end fittings for rear window glass operation. StrongArm manufactures its lift supports beyond standard industry requirements to deliver smooth movement and durable performance in daily use.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4404 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven lift support movement\u003c\/li\u003e\n\u003cli\u003eWeak support force at the back glass\u003c\/li\u003e\n\u003cli\u003eWear-related loss of pressure in the original support\u003c\/li\u003e\n\u003cli\u003eDifficulty opening or holding the rear window glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible With 1983-1994 Chevrolet S10 Blazer, without Rear Defroster; 1983-1994 GMC Jimmy, without Rear Defroster; 1983-1991 GMC S15 Jimmy, without Rear Defroster; 1982-1983 Buick Regal; 1978-1983 Chevrolet Malibu; 1978-1983 Oldsmobile Custom Cruiser; 1982-1983 Pontiac Bonneville; 1978-1981 Buick Century; 1980-1981 Pontiac Grand LeMans; 1978-1981 Pontiac LeMans. Verify the vehicle’s rear glass configuration before ordering, especially on applications noted without rear defroster. For best results, inspect the mounting points and ball studs for wear before installing the replacement support. StrongArm 4404 should be matched to the correct application by year, make, model, and rear glass equipment.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to support smooth operation and long service life. The brand’s manufacturing approach focuses on consistent fit and controlled performance for automotive glass support applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613231481013,"sku":"BBZN-4404","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4404_Fro.jpg?v=1774984311"},{"product_id":"strongarm-4423-back-glass-lift-support","title":"StrongArm 4423 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Bronco II\u003c\/h2\u003e\u003cp\u003eStrongArm 4423 is a specific-fit back glass lift support for the 1984-1990 Ford Bronco II with a movable rear window. It uses a pressurized cylinder design to help hold the rear glass in position and deliver smooth, controlled operation.\u003c\/p\u003e\u003cp\u003eBuilt with a black steel outer cylinder, nylon 10mm ball socket ends, and internal rubber and Teflon materials, this StrongArm lift support is engineered for consistent rear window support. The StrongArm 4423 is a direct-fit solution for Ford Bronco II rear glass service and replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the Ford Bronco II\u003c\/li\u003e\n\u003cli\u003eFits 1984-1990 Ford Bronco II, with movable rear window\u003c\/li\u003e\n\u003cli\u003ePressurized cylinder construction for rear glass support\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable housing\u003c\/li\u003e\n\u003cli\u003eNylon 10mm ball socket ends for secure attachment points\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.2 in.; compressed length: 11.0 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.19 in. with 30.0 maximum force\u003c\/li\u003e\n\u003cli\u003eCross-references AMS Automotive 4423 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4423 is a back glass lift support engineered for the rear window glass on 1984-1990 Ford Bronco II models equipped with a movable rear window. The unit is built as a pressurized cylinder with a steel outer body, nylon ball socket ends, and internal rubber and Teflon components to support smoother movement and consistent operation. This part number is also referenced as StrongArm 4423 in interchange listings for the same application.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a 1984 Ford Bronco II back glass lift support, a 1987 Ford Bronco II rear window support, or a 1990 Ford Bronco II lift support for movable rear glass, this specific-fit part provides the correct application match. The StrongArm 4423 is intended for rear glass service where controlled opening and holding force are needed.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow-moving back window support\u003c\/li\u003e\n\u003cli\u003eDrooping hatch glass during loading or unloading\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window lift action\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle is a 1984-1990 Ford Bronco II with a movable rear window before ordering. Match the existing end style and length specifications to confirm fitment, and inspect the mounting points for wear before installation. Lift supports should be replaced in pairs to maintain balanced rear glass operation and reliable support.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to support smoother operation and longer service life. The 4423 is built to meet the demands of rear glass applications on the Ford Bronco II.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613264216245,"sku":"BBZN-4423","price":24.21,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4423_Fro.jpg?v=1774984314"},{"product_id":"strongarm-4440-back-glass-lift-support","title":"StrongArm 4440 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Taurus and Sable\u003c\/h2\u003e\u003cp\u003eStrongArm 4440 is a specific-fit back glass lift support for select Ford Taurus and Mercury Sable models from 1986-1995. It uses a pressurized cylinder design to hold rear window glass in the open position and provide controlled movement during liftgate or back glass operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit replacement for select Ford Taurus and Mercury Sable applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.93 in.; extended length: 18.03 in.; stroke length: 6.1 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 41.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 8mm end and swivel eyelet end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation and wear resistance\u003c\/li\u003e\n\u003cli\u003eStrongArm 4440 cross-references AMS Automotive 4440 and OE-style replacement numbers including F0DZ7442104A and D4440\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4440 is engineered for rear glass support on 1986-1995 Ford Taurus and 1986-1995 Mercury Sable vehicles. The pressurized cylinder construction helps maintain steady support for the back glass while allowing controlled opening and closing, and the specific-fit design matches the listed application without universal adaptation. If you are replacing a worn rear window support on a Ford Taurus or Mercury Sable, StrongArm 4440 provides the correct length, stroke, and end fittings for the application.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4440 and OE-style numbers such as F0DZ7442104A and D4440 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support action\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle application before installation by matching the year, make, model, and end fittings. For rear glass support service, inspect the mounting points and surrounding hardware for wear or damage before installing the replacement support. StrongArm recommends replacing lift supports in pairs to maintain balanced operation and reliable support of the hood, hatch, or rear glass.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eEach StrongArm lift support is custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. This part is built as a specific-fit replacement for the listed Ford Taurus and Mercury Sable applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613267722421,"sku":"BBZN-4440","price":23.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4440_Fro.jpg?v=1774984316"},{"product_id":"strongarm-4447-back-glass-lift-support","title":"StrongArm 4447 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for GM Applications\u003c\/h2\u003e\u003cp\u003eStrongArm 4447 is a specific-fit back glass lift support for select Buick, Oldsmobile, Pontiac, and Chevrolet vehicles. It uses a pressurized cylinder to hold rear window glass in the open position and restore controlled lift and support for the hatch glass.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.86 in.; compressed length: 11.75 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.11 in. with 75.0 maximum force\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket ends with nylon electrical-style sockets on both ends\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smoother operation and wear resistance\u003c\/li\u003e\n\u003cli\u003eStrongArm 4447 cross-references AMS Automotive 4447 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4447 is engineered as a rear glass lift support for vehicles that use a pressurized strut to raise and hold the back window glass. The specific-fit design helps maintain proper geometry and consistent operation on applications such as the 1984-1996 Buick Century, 1986-1996 Oldsmobile Cutlass Ciera, 1987-1994 Oldsmobile Cutlass Cruiser, 1984-1991 Pontiac 6000, and 1984-1990 Chevrolet Celebrity. If you are searching for a StrongArm 4447 lift support for Buick Century rear glass or a back glass strut for Chevrolet Celebrity hatch glass, this part matches those vehicle-specific applications.\u003c\/p\u003e\u003cp\u003eStrongArm builds each lift support beyond standard industry requirements and uses pressurized construction for smooth movement and dependable rear glass support. The steel cylinder, nylon ball socket ends, and internal rubber\/Teflon materials are selected to support consistent operation over repeated use. The StrongArm 4447 part number is also referenced in interchange listings for related aftermarket applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow hatch glass lift action\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent back window support\u003c\/li\u003e\n\u003cli\u003eNoise or binding during rear glass movement\u003c\/li\u003e\n\u003cli\u003eLoss of controlled opening on liftback or hatch glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke, and ball socket end style before installation. This is a specific-fit rear glass support, so confirm vehicle application details for the exact year and model. For proper operation and balanced support, replace lift supports in pairs when servicing the rear glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm manufactures this lift support to meet demanding fit and function requirements for automotive rear glass applications. The 4447 is built as a vehicle-specific replacement for consistent support and controlled motion on the listed GM models.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613269885109,"sku":"BBZN-4447","price":23.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4447_Fro.jpg?v=1774984319"},{"product_id":"strongarm-4528-back-glass-lift-support","title":"StrongArm 4528 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Jeep Grand Cherokee\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4528. It is a specific-fit gas strut engineered for 1999-2004 Jeep Grand Cherokee models and built with a steel outer cylinder, nylon socket ends, and a 27.0 maximum force rating for consistent rear window support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 1999-2004 Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 4528 for direct application matching\u003c\/li\u003e\n\u003cli\u003eCompressed length: 9.29 in; extended length: 14.55 in; stroke length: 5.26 in\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eNylon socket end design: captive ball \/ nylon socket and 8 mm ball socket\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 27.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4528 is a rear window glass lift support made for the back glass on 1999-2004 Jeep Grand Cherokee vehicles. This gas-charged support uses a specific-fit design with captive ball and nylon socket ends to match the original mounting style, while the steel cylinder construction helps maintain stable operation over repeated opening and closing cycles. If you are replacing a worn Jeep Grand Cherokee lift support, part number 4528 provides the correct length, stroke, and force characteristics for the application.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4528 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBack glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eRear window glass that opens slowly or unevenly\u003c\/li\u003e\n\u003cli\u003eLift support loss of pressure from age or wear\u003c\/li\u003e\n\u003cli\u003eExcess effort needed to raise the rear glass on a Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eNoise or weak support during hatch glass operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the mounting style and length before installation on your 1999-2004 Jeep Grand Cherokee. Replace lift supports in pairs to maintain balanced rear glass support and consistent opening force. Confirm the ball socket engagement at both ends and check that the rear glass opens and closes smoothly after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life. Part number 4528 is built for specific-fit rear glass support on Jeep Grand Cherokee applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613313794229,"sku":"BBZN-4528","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4528_Fro.jpg?v=1774984335"},{"product_id":"strongarm-4575-back-glass-lift-support","title":"StrongArm 4575 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Specific Fit Applications\u003c\/h2\u003e\u003cp\u003eStrongArm 4575 is a specific-fit back glass lift support for rear window glass applications on select GM and Isuzu vehicles. It uses a pressurized cylinder design to help hold the back glass in position and deliver smooth, controlled operation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass\u003c\/li\u003e\n\u003cli\u003eCompressed length: 13.97 in.; extended length: 19.97 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.0 in. with 42.0 maximum force\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with nylon 8 mm ball socket ends\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for consistent movement\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2003-2007 Isuzu Ascender, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2007 Saturn Relay, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2006 Chevrolet Trailblazer EXT, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2006 GMC Envoy XL, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2005 GMC Envoy XUV, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4575 is engineered as a direct replacement back glass lift support for select Chevrolet Trailblazer EXT, GMC Envoy XL, GMC Envoy XUV, Saturn Relay, and Isuzu Ascender models. The pressurized cylinder construction helps maintain rear glass position during opening and closing, while the steel outer cylinder and nylon ball socket ends support reliable attachment at the liftgate glass mounting points. This part cross-references Monroe Shocks \u0026amp; Struts 901652 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window glass that drops unexpectedly\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support movement\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass operation\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Quality\u003c\/h2\u003e\u003cp\u003eVerify compressed length, extended length, stroke, and 8 mm ball socket end type before installation. Replace in pairs when servicing both sides of the rear glass support system to maintain balanced operation. StrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer-lasting performance.\u003c\/p\u003e\u003cp\u003eStrongArm 4575 is built for specific-fit applications and is intended to match the original mounting style on the listed vehicles. Confirm vehicle fitment by year, make, and model before ordering.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613340205237,"sku":"BBZN-4575","price":19.06,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4575_Fro.jpg?v=1774984346"},{"product_id":"strongarm-4576-back-glass-lift-support","title":"StrongArm 4576 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Trailblazer, Envoy, and More\u003c\/h2\u003e\u003cp\u003eRestore controlled rear window operation with this StrongArm back glass lift support, part number 4576. It is a specific-fit pressurized cylinder engineered for rear glass applications on select Chevrolet, GMC, Saab, Buick, and Isuzu models, including Chevrolet Trailblazer and GMC Envoy.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 21.6 in.; compressed length: 14.01 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.59 in. for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force: 34.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 8mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eFits 2002-2009 Chevrolet Trailblazer, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2009 GMC Envoy, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Saab 9-7x, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008 Isuzu Ascender, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2007 Buick Rainier, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Oldsmobile Bravada, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBuilt for Rear Glass Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4576 is a rear glass lift support that uses pressurized cylinder construction to hold the back window in position during opening and closing. The specific-fit design helps ensure proper alignment on the listed vehicles, while the steel outer cylinder and nylon ball socket ends support consistent operation. This part number 4576 is a direct replacement style solution for rear glass lift support service on Chevrolet Trailblazer and GMC Envoy applications, along with the related Saab 9-7x, Buick Rainier, Isuzu Ascender, and Oldsmobile Bravada platforms.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4576 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window dropping too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eHard-to-lift rear glass on hatch or liftgate glass\u003c\/li\u003e\n\u003cli\u003eNoisy or rough rear window movement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle fitment by year, make, and model before installation. Inspect the mounting points and ball studs for wear or damage before attaching the new support. For balanced operation and even wear, replace lift supports in pairs when servicing the rear glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life in automotive applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613341352117,"sku":"BBZN-4576","price":19.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4576_Fro.jpg?v=1774984347"},{"product_id":"strongarm-4608-back-glass-lift-support","title":"StrongArm 4608 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Explorer and Mountaineer\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4608. It is a specific-fit replacement engineered for smooth operation and consistent support on select Ford, Mercury, and Mazda applications, including Ford Explorer, Ford Explorer Sport, Mercury Mountaineer, and Mazda Navajo.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.26 in.; extended length: 16.89 in.; stroke length: 5.63 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 37.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable support performance\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 8mm end on one side and swivel eyelet on the other\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials used in the support construction\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 4608 for direct identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4608 is a back glass lift support built for rear window glass applications where controlled opening and holding force are required. The unit uses a pressurized cylinder design and is custom engineered to deliver smoother operation and longer-lasting performance than a worn or weak support. With a compressed length of 11.26 inches, an extended length of 16.89 inches, and a 5.63-inch stroke, it is sized for the specified rear glass fitment. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1991-2001 Ford Explorer, N\/A; 2001-2002 Ford Explorer Sport, N\/A; 1997-2001 Mercury Mountaineer, N\/A; and 1991-1994 Mazda Navajo, N\/A. If you are replacing a worn rear hatch glass support on a Ford Explorer or Mercury Mountaineer, StrongArm 4608 provides the correct specific-fit replacement path.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift action when opening the back glass\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent support at the rear window\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support cylinder\u003c\/li\u003e\n\u003cli\u003eDifficulty holding the back glass in the raised position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eReplace lift supports in pairs to maintain balanced rear glass support and consistent operation. Verify the end fittings before installation: ball socket (nylon) 8mm on one end and swivel eyelet on the other. Confirm vehicle application by year and model before ordering, especially for 2001-2002 Ford Explorer Sport and the listed Ford Explorer, Mercury Mountaineer, and Mazda Navajo applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to support smoother operation and longer service life in automotive rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613394763957,"sku":"BBZN-4608","price":19.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4608_Fro.jpg?v=1774984354"},{"product_id":"strongarm-4642-back-glass-lift-support","title":"StrongArm 4642 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Chevrolet Blazer and GMC Jimmy\u003c\/h2\u003e\u003cp\u003eRestore smooth rear glass operation with this StrongArm back glass lift support, part number 4642. Built as a specific-fit replacement, it is engineered for the rear window glass on select Chevrolet Blazer and GMC Jimmy applications, including 1995-2005 Chevrolet Blazer and 1995-2001 GMC Jimmy with Dropgate.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.6 in.; extended length: 17.5 in.; stroke length: 5.9 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 49.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable construction\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 10mm on one end and nylon 16-degree on the other\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials used in the support assembly\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 4642 for direct identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4642 is a back glass lift support built for rear hatch glass service on compatible Chevrolet Blazer and GMC Jimmy vehicles. It uses a pressurized cylinder design to hold the rear window glass in the open position and provide controlled movement during opening and closing. The steel outer cylinder, nylon ball socket ends, and 49.0 maximum force rating support consistent operation in rear glass applications where stable lift assistance matters. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With: Fits 1995-2005 Chevrolet Blazer, N\/A. Fits 1995-2001 GMC Jimmy, N\/A with Dropgate. StrongArm 4642 is a direct-fit replacement for these rear glass applications and is identified by part number 4642 in catalog and service lookup use.\u003c\/p\u003e\u003ch2\u003eCommon Replacement Reasons\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eLiftgate glass feels heavy or difficult to raise\u003c\/li\u003e\n\u003cli\u003eBack window opens unevenly or closes too quickly\u003c\/li\u003e\n\u003cli\u003eWorn gas pressure causes weak support at the rear glass\u003c\/li\u003e\n\u003cli\u003eOriginal lift support no longer holds the hatch glass securely\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and rear glass configuration before ordering. This support is a specific-fit part, so matching the end fittings and compressed\/extended lengths is important for proper operation. For service consistency, replace lift supports in pairs when the opposite side is also worn, and confirm the rear glass opens and closes smoothly after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smooth operation and long service life in automotive use. Part number 4642 is built for the listed Chevrolet Blazer and GMC Jimmy rear glass applications and is designed to meet the dimensional and force requirements of those vehicles.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613404397749,"sku":"BBZN-4642","price":19.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4642_Fro.jpg?v=1774984361"},{"product_id":"strongarm-4644-back-glass-lift-support","title":"StrongArm 4644 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4644 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4644 is a specific-fit back glass lift support for select Isuzu and Honda applications. It uses a pressurized cylinder design to help hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit rear glass lift support for targeted vehicle applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 19.7 in.; compressed length: 11.75 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.95 in. for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 31.0\u003c\/li\u003e\n\u003cli\u003eCompatible with 1991-2004 Isuzu Rodeo, 2001-2003 Isuzu Rodeo Sport, 1994-2002 Honda Passport, and 1999-2000 Isuzu Amigo\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis StrongArm back glass lift support is engineered for rear window glass applications where controlled lift and stable hold are required. The 19.0 mm cylinder outside diameter, 8.0 mm inner shaft diameter, and 7.95 in. stroke length support predictable motion, while the nylon ball socket ends provide a direct connection style for the listed vehicles. StrongArm 4644 is built as a specific replacement for rear glass service on the Honda Passport, Isuzu Rodeo, Isuzu Rodeo Sport, and Isuzu Amigo.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or weak lift support performance\u003c\/li\u003e\n\u003cli\u003eHatch glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle fitment by year, make, and model before installation. Inspect the mounting points and ball studs for wear or damage before attaching the new support. For safe and reliable rear glass support, replace lift supports in pairs when the vehicle uses a matched left\/right setup.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. Part number 4644 is built for specific-fit rear glass applications and is backed by StrongArm’s manufacturing quality standards.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613404594357,"sku":"BBZN-4644","price":19.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4644_Fro_5800189a-ddb8-4773-a3c5-bafdf5ae3ca7.jpg?v=1774984362"},{"product_id":"strongarm-4645-back-glass-lift-support","title":"StrongArm 4645 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Villager and Quest\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4645. It is a specific-fit replacement engineered for the rear window glass on select Mercury Villager and Nissan Quest models from 1993-1998.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.98 in; compressed length: 10.98 in\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.03 in for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 40.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 8mm end and nylon 16-degree end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating consistency\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4645 is a rear glass lift support built for the back glass on 1993-1998 Mercury Villager and 1993-1998 Nissan Quest. The pressurized cylinder helps hold the rear window glass in position and provides controlled lift and lowering action. With a 17.98-inch extended length, 10.98-inch compressed length, and 7.03-inch stroke, this lift support is sized for the specified application and uses ball socket nylon ends for a secure connection.\u003c\/p\u003e\u003cp\u003eStrongArm manufactures each lift support to meet demanding performance standards for smoother operation and longer service life. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application. Part number 4645 is a direct-fit option for owners searching for a rear hatch glass lift support for Mercury Villager or Nissan Quest models in the listed years.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support response\u003c\/li\u003e\n\u003cli\u003eDrooping back glass during loading or unloading\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window glass movement\u003c\/li\u003e\n\u003cli\u003eNoise or reduced control when opening the rear glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year and rear glass application before installation. Inspect the mounting points and ball studs for wear or damage, and confirm the end styles match the original support. For balanced operation and consistent support, replace lift supports in pairs when servicing the rear glass.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver consistent operation and long-lasting performance in automotive lift support applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613404758197,"sku":"BBZN-4645","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4645_Fro.jpg?v=1774984363"},{"product_id":"strongarm-4646-back-glass-lift-support","title":"StrongArm 4646 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4646 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4646 is a specific-fit back glass lift support for select Ford Taurus and Mercury Sable models. It restores controlled rear window glass movement with a pressurized cylinder built for smooth operation and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 10.46 in.; extended length: 16.79 in.; stroke length: 6.33 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 34.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 16-degree end and swivel eyelet end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating durability\u003c\/li\u003e\n\u003cli\u003eFits 1996-2005 Ford Taurus and 1996-2005 Mercury Sable\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis StrongArm 4646 lift support is engineered for rear glass applications on 1996-2005 Ford Taurus and 1996-2005 Mercury Sable vehicles. The pressurized cylinder helps hold the back glass in position while providing controlled opening and closing action, with dimensions and force output matched to the application. This part number 4646 is also referenced by AMS Automotive 4646 and cross-references Monroe Shocks \u0026amp; Struts 901178 for the same application.\u003c\/p\u003e\u003cp\u003eBuilt with a steel outer cylinder, nylon ball socket end, and swivel eyelet end, StrongArm 4646 is made for direct replacement use on the listed Ford Taurus and Mercury Sable fitments. The 10.46-inch compressed length, 16.79-inch extended length, and 6.33-inch stroke length are important when matching rear glass support geometry on these vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window glass that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eBinding or uneven rear glass movement\u003c\/li\u003e\n\u003cli\u003eWorn support hardware on Ford Taurus and Mercury Sable rear glass assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke length, and end fittings before installation. For rear glass service, replace lift supports in pairs to maintain balanced support and consistent operation. Confirm the vehicle application against the listed fitment for 1996-2005 Ford Taurus and 1996-2005 Mercury Sable before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Part number 4646 is built as a specific-fit replacement for the listed Ford Taurus and Mercury Sable rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613405413557,"sku":"BBZN-4646","price":20.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4646_Fro.jpg?v=1774984363"},{"product_id":"strongarm-4650-back-glass-lift-support","title":"StrongArm 4650 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4650 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eRestore smooth rear window operation with this StrongArm back glass lift support, part number 4650. It is a specific-fit gas strut engineered for rear glass applications on select Chevrolet, GMC, and Cadillac SUVs and utility vehicles from 1992-1999.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 17.63 in.; compressed length: 11.83 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.8 in. for controlled opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force: 85.0 for rear glass support\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials used in the support construction\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4650 is a rear glass lift support built for specific vehicle applications, including Chevrolet Blazer, Tahoe, C1500 Suburban, C2500 Suburban, K1500 Suburban, K2500 Suburban, GMC Yukon, and Cadillac Escalade coverage within the listed years. It is engineered as a pressurized cylinder to hold rear window glass in position and provide controlled movement during opening and closing. This part number 4650 is also cross-referenced to AMS Automotive 4650 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1992-1999 Chevrolet Blazer, 1992-1999 Chevrolet Tahoe, 1992-1999 Chevrolet C1500 Suburban, 1992-1999 Chevrolet C2500 Suburban, 1992-1999 Chevrolet K1500 Suburban, 1992-1999 Chevrolet K2500 Suburban, 1992-1999 GMC Yukon, 1992-1999 GMC C1500 Suburban, 1992-1999 GMC C2500 Suburban, 1992-1999 GMC K1500 Suburban, 1992-1999 GMC K2500 Suburban, and 1999 Cadillac Escalade. Fitment notes vary by rear defroster and rear window wiper configuration, so verify the exact vehicle setup before ordering.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eHatch or back window that drops unexpectedly\u003c\/li\u003e\n\u003cli\u003eWeak or slow rear glass lift action\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window support\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eReplace lift supports in pairs to maintain balanced rear glass support and consistent operation. Confirm the vehicle’s rear defroster and rear window wiper configuration, along with the mounting location noted in the fitment data, before installation. Compare the compressed length, extended length, stroke length, and 10mm ball socket ends to the original support for proper match-up.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life in automotive rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613405774005,"sku":"BBZN-4650","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4650_Fro_fc18b4b6-1f23-4408-96a8-8b49cef73361.jpg?v=1774984364"},{"product_id":"strongarm-4676-back-glass-lift-support","title":"StrongArm 4676 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Ford Expedition and Lincoln Navigator\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4676. It is a specific-fit pressurized cylinder engineered for the rear window glass on select Ford and Lincoln SUVs, with smooth operation and consistent holding force.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for exact vehicle application\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.1 in.; extended length: 17.85 in.; stroke length: 6.75 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 31.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10mm end and swivel eyelet end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating durability\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm 4676 is a rear window glass lift support built for 1997-2002 Ford Expedition and 1998-2002 Lincoln Navigator applications. As a pressurized cylinder, it helps control the opening and holding action of the back glass, supporting smoother liftgate glass operation and more consistent rear access. This part number 4676 is engineered to match the listed fitment with the correct length, stroke, and end fittings for the application.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 4676 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift support pressure\u003c\/li\u003e\n\u003cli\u003eSlow, uneven, or difficult back glass opening\u003c\/li\u003e\n\u003cli\u003eNoise or binding during rear window glass movement\u003c\/li\u003e\n\u003cli\u003eLoss of support on the rear hatch glass of a Ford Expedition or Lincoln Navigator\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year and model before ordering. This StrongArm back glass lift support is a specific-fit part for the listed Ford Expedition and Lincoln Navigator applications, and the end fittings must match the original mounting points. Inspect the mounting sockets and attachment points for wear before installation so the new support can operate correctly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that its lift supports are custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Lift supports should be replaced in pairs to maintain safe, reliable rear glass support.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613409214645,"sku":"BBZN-4676","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4676_Fro.jpg?v=1774984367"},{"product_id":"strongarm-4678-back-glass-lift-support","title":"StrongArm 4678 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Jeep Grand Cherokee\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 4678. It is a specific-fit gas strut engineered for the 1994-1998 Jeep Grand Cherokee rear window glass, with dimensions and force matched for consistent opening and holding performance.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the 1994-1998 Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.64 in.; compressed length: 11.08 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.56 in. with 27.0 maximum force\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: 10 mm nylon on one end and 8 mm nylon on the other\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 4678 for direct reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4678 is a rear window glass lift support built for the Jeep Grand Cherokee rear hatch glass application. As a pressurized cylinder, it helps control the opening and holding action of the back glass, while the specific-fit design supports proper alignment with the factory mounting points. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003cp\u003eFor shoppers searching for a 1994 Jeep Grand Cherokee back glass lift support, a 1995-1998 Jeep Grand Cherokee rear window strut, or a StrongArm 4678 replacement lift support, this unit matches the listed vehicle coverage and dimensional specs. The steel outer cylinder, nylon ball socket ends, and 27.0 force rating are specified to support smooth rear glass operation.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift action at the hatch glass\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window support\u003c\/li\u003e\n\u003cli\u003eDifficulty opening the back glass smoothly\u003c\/li\u003e\n\u003cli\u003eWorn gas strut performance on the Jeep Grand Cherokee\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1994-1998 Jeep Grand Cherokee, rear glass application. Verify the ball socket sizes and compressed\/extended lengths against the original support before installation. For safe, reliable support of the rear glass, replace lift supports in pairs when servicing the vehicle.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer-lasting performance. Part number 4678 is built to the listed specifications for the Jeep Grand Cherokee rear glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613409542325,"sku":"BBZN-4678","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4678_Fro.jpg?v=1774984368"},{"product_id":"strongarm-4720-back-glass-lift-support","title":"StrongArm 4720 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 4720 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 4720 is a specific-fit back glass lift support engineered for rear window glass applications on select Ford and Mercury vehicles. It provides pressurized assistance for smoother opening and controlled holding of the rear glass on 1982 Mercury Cougar, 1983-1986 Ford LTD, and 1983-1986 Mercury Marquis applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 22.9 in.; compressed length: 13.66 in.; stroke length: 9.24 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 49.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for consistent operation\u003c\/li\u003e\n\u003cli\u003eCross-reference: AMS Automotive 4720\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 4720 is built as a direct-fit rear glass lift support for vehicles that use a pressurized cylinder to raise and hold the back glass. The design uses a steel outer cylinder, nylon ball socket ends, and a 49.0 force rating to deliver controlled movement and stable support for the rear window glass. This part number is listed for 1982 Mercury Cougar, 1983-1986 Ford LTD, and 1983-1986 Mercury Marquis, making it a targeted replacement for those rear glass lift support applications. StrongArm manufactures each lift support to tighter-than-standard specifications for smoother operation and longer service life, and part number 4720 is also referenced as StrongArm 4720 in interchange listings.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven lift action at the back glass\u003c\/li\u003e\n\u003cli\u003eWeak support when opening the rear window glass\u003c\/li\u003e\n\u003cli\u003eDrooping or falling rear hatch glass\u003c\/li\u003e\n\u003cli\u003eNoise or rough movement from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke length, and 10 mm ball socket ends before installation to confirm the correct rear glass support for your vehicle. For consistent operation and balanced support, replace lift supports in pairs when servicing the rear glass on Ford LTD, Mercury Marquis, or Mercury Cougar applications. Confirm the mounting points and fitment details against the vehicle before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to support smoother operation and longer-lasting performance in automotive applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613446668469,"sku":"BBZN-4720","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4720_Fro.jpg?v=1774984374"},{"product_id":"strongarm-4799-back-glass-lift-support","title":"StrongArm 4799 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Liftgate Applications\u003c\/h2\u003e\u003cp\u003eStrongArm 4799 is a specific-fit back glass lift support for select Chevrolet, GMC, and Oldsmobile liftgate applications. It uses a pressurized cylinder design to help hold rear window glass in the open position and deliver smooth, controlled movement.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eExtended length: 23.93 in.; compressed length: 14.18 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 9.75 in. for controlled opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 40.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eEnd fittings: 10 mm nylon ball socket and swivel eyelet\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm 4799 is engineered for rear glass support on vehicles equipped with a liftgate, including Fits 2004-2005 Chevrolet Blazer, N\/A; Fits 1997-2003 Chevrolet Blazer, N\/A with Liftgate; Fits 1997-2001 GMC Jimmy, N\/A with Liftgate; and Fits 1997-2001 Oldsmobile Bravada, N\/A with Liftgate. This back glass lift support is built with a steel outer cylinder and precision end fittings to match the specified application and restore consistent rear glass operation. The part number 4799 is also referenced in aftermarket interchange listings for the same application.\u003c\/p\u003e\u003cp\u003eStrongArm states that its lift supports are custom engineered and manufactured beyond industry standards to promote smoother operation and longer service life. For search relevance, this StrongArm 4799 rear glass support is a direct-fit option for Chevrolet Blazer liftgate rear glass, GMC Jimmy liftgate rear glass, and Oldsmobile Bravada liftgate rear glass service.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven liftgate glass movement\u003c\/li\u003e\n\u003cli\u003eWeak support when opening the back window glass\u003c\/li\u003e\n\u003cli\u003eDrooping rear glass after release\u003c\/li\u003e\n\u003cli\u003eNoise or rough operation from worn lift support hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eReplace lift supports in pairs to maintain balanced support and reliable operation. Verify the end fittings, compressed length, extended length, and stroke length against the vehicle before installation. Confirm the application is the rear glass\/liftgate position for the listed Chevrolet Blazer, GMC Jimmy, or Oldsmobile Bravada fitment.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered for the specified application and manufactured to exceed industry standards for consistent operation and durability. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613475012789,"sku":"BBZN-4799","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4799_Fro.jpg?v=1774984385"},{"product_id":"strongarm-4816-back-glass-lift-support","title":"StrongArm 4816 Back Glass Lift Support - Right","description":"\u003ch2\u003eBack Glass Lift Support for Nissan Pathfinder\u003c\/h2\u003e\u003cp\u003eStrongArm 4816 is a specific-fit back glass lift support for the right side of 1987-1995 Nissan Pathfinder models. It uses a pressurized cylinder design to hold rear window glass in position and deliver controlled opening and closing action.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the right side\u003c\/li\u003e\n\u003cli\u003eFits 1987-1995 Nissan Pathfinder, right\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.54 in.\u003c\/li\u003e\n\u003cli\u003eExtended length: 18.64 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.1 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force: 34.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10 mm end and off-set blade with bracket end\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 4816 is engineered as a rear window glass support for Nissan Pathfinder applications that require a right-side, specific-fit replacement. The cylinder is built with a steel outer body, rubber and Teflon materials, and a pressurized gas design to provide consistent lift and controlled movement for the back glass. This part cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent lift at the hatch glass\u003c\/li\u003e\n\u003cli\u003eWorn support causing poor rear glass control\u003c\/li\u003e\n\u003cli\u003eReplacement need for a right-side Nissan Pathfinder lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle is a 1987-1995 Nissan Pathfinder with right-side rear glass support requirements before ordering. Compare the compressed length, extended length, stroke length, and end fittings to the original part for proper match. Replace the support in the correct position and confirm smooth operation of the back glass after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Lift supports should be replaced in pairs to maintain safe, reliable rear glass support.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43613479731381,"sku":"BBZN-4816","price":19.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_4816_Fro.jpg?v=1774984388"},{"product_id":"strongarm-6157-back-glass-lift-support","title":"StrongArm 6157 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for GM SUVs\u003c\/h2\u003e\u003cp\u003eStrongArm 6157 is a specific-fit back glass lift support for select Cadillac, Chevrolet, and GMC vehicles. It uses a pressurized cylinder design to help hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit replacement for the rear back glass application\u003c\/li\u003e\n\u003cli\u003eExtended length: 19.75 in.; compressed length: 12.0 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 7.75 in. for smooth opening and closing travel\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 36.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 8 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for durable operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 6157 is engineered as a direct-fit back glass lift support for vehicles including the 2007-2014 Cadillac Escalade, 2007-2014 Cadillac Escalade ESV, 2007-2013 Cadillac Escalade EXT, 2007-2014 Chevrolet Tahoe, 2007-2014 Chevrolet Suburban 1500, 2007-2013 Chevrolet Suburban 2500, 2007-2014 GMC Yukon, 2007-2014 GMC Yukon XL 1500, and 2007-2013 GMC Yukon XL 2500. This part number 6157 is built to match the original rear glass support application with the correct length, stroke, and end fittings for a precise replacement. This part cross-references AMS Automotive 6157 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eLiftgate glass dropping too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent rear window support\u003c\/li\u003e\n\u003cli\u003eBinding or uneven movement at the back glass\u003c\/li\u003e\n\u003cli\u003eWorn gas strut performance on the rear hatch glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, and model before ordering. Confirm the ball socket 8 mm end style and overall length match the original support on your vehicle. For proper operation and balanced support, replace lift supports in pairs when servicing the rear glass system. After installation, cycle the back glass several times to confirm smooth movement and secure engagement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smooth operation and long service life in automotive applications. Part number 6157 is built for the specified GM fitments listed above and follows the original-style rear glass support format.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617633632437,"sku":"BBZN-6157","price":19.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6157_Fro_a97e9f15-10ec-44b6-8b3f-a7f41aaa4f24.jpg?v=1774984441"},{"product_id":"strongarm-6192-back-glass-lift-support","title":"StrongArm 6192 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Pathfinder and QX4\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 6192. It is a specific-fit gas strut engineered for the rear window glass on select Nissan Pathfinder and INFINITI QX4 models from 1999-2004.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.65 in.; extended length: 18.9 in.; stroke length: 6.25 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 42.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket nylon 10 mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smoother operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 6192 is a pressurized lift support built for rear glass applications where consistent opening and holding force matters. The cylinder is custom engineered to meet the application requirements for 1999-2004 Nissan Pathfinder and 1999-2003 INFINITI QX4 models, including vehicles from 12\/1998 production. This part number 6192 uses a steel outer cylinder, nylon ball socket ends, and a 42.0 force rating to help maintain steady rear glass support during use.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 6192 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Replacement Reasons\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass drops too quickly when opened\u003c\/li\u003e\n\u003cli\u003eLift support no longer holds the back glass in position\u003c\/li\u003e\n\u003cli\u003eWeak or inconsistent opening force at the hatch glass\u003c\/li\u003e\n\u003cli\u003eVisible wear, leakage, or reduced strut pressure\u003c\/li\u003e\n\u003cli\u003eUneven rear glass support on Nissan Pathfinder or INFINITI QX4\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 1999-2004 Nissan Pathfinder, rear glass; Fits 1999-2003 INFINITI QX4, rear glass. Verify the compressed length, extended length, stroke length, and 10 mm ball socket ends before installation. Replace in pairs when servicing the rear glass support system to maintain balanced operation and reliable holding force.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards for smoother operation and longer-lasting performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617647493301,"sku":"BBZN-6192","price":19.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6192_Fro.jpg?v=1774984452"},{"product_id":"strongarm-6194-back-glass-lift-support","title":"StrongArm 6194 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Jeep Commander\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement on your Jeep Commander with StrongArm Part Number 6194. This specific-fit back glass lift support is engineered for 2006-2010 Jeep Commander applications and uses pressurized cylinder construction to help hold the rear window glass in position during opening and closing.\u003c\/p\u003e\u003cp\u003eStrongArm 6194 is built with a black steel outer cylinder, rubber and Teflon materials, and nylon ball socket ends for a precise connection. With an extended length of 16.06 inches, compressed length of 10.56 inches, stroke length of 5.5 inches, and maximum force of 42.0, it is sized for the rear glass support application on the Jeep Commander.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2006-2010 Jeep Commander, rear glass application\u003c\/li\u003e\n\u003cli\u003eSpecific-fit design for direct vehicle application\u003c\/li\u003e\n\u003cli\u003ePressurized cylinder construction for rear glass support\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with nylon ball socket ends\u003c\/li\u003e\n\u003cli\u003eExtended length: 16.06 in; compressed length: 10.56 in; stroke length: 5.5 in\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 42.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm Part Number 6194 is a back glass lift support made for the Jeep Commander rear window glass. Lift supports are pressurized cylinders used to support hoods, hatches, and rear glass, and this unit follows that same function with a specific-fit design for 2006-2010 Jeep Commander models. The construction combines steel, rubber, and Teflon materials to support smoother operation and consistent movement of the rear glass.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 819-6593, 901873) for the same application. StrongArm 6194 is also referenced by AMS Automotive 6194 and other interchange numbers listed for this vehicle fitment.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support response\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window glass movement\u003c\/li\u003e\n\u003cli\u003eDifficulty opening or holding the Jeep Commander back glass\u003c\/li\u003e\n\u003cli\u003eWear-related loss of support pressure over time\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle fitment by matching the 2006-2010 Jeep Commander application before installation. Inspect the mounting points and ball socket connections for wear or damage, and confirm the support is oriented correctly for the rear glass position. Because lift supports work as a matched system, replacing related supports together is commonly recommended for balanced operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards to support smoother operation and longer-lasting performance. Part Number 6194 is built to meet the demands of rear glass support service on the Jeep Commander.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617648967861,"sku":"BBZN-6194","price":20.21,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6194_Fro.jpg?v=1774984453"},{"product_id":"strongarm-6260-back-glass-lift-support","title":"StrongArm 6260 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Ford, Mazda, and Mercury\u003c\/h2\u003e\u003cp\u003eStrongArm 6260 is a specific-fit back glass lift support engineered for rear window glass applications on select Ford, Mazda, and Mercury vehicles. It uses a pressurized cylinder design to provide controlled lift and hold performance for the rear glass on compatible hatch and liftgate setups.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for targeted vehicle applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.17 in.; extended length: 17.42 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 6.25 in. with 33.0 maximum force\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 8 mm and nylon 10 mm\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation and wear resistance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eStrongArm 6260 is built as a rear glass lift support for vehicles that use a pressurized strut to raise and hold the back glass. The cylinder measures 15.0 mm in outside diameter with a 6.0 mm inner shaft diameter, and its specific-fit design helps match the original application geometry. This part cross-references AMS Automotive 6260 for the same application. It is listed for 2008-2012 Ford Escape, 2008-2011 Mazda Tribute, and 2008-2011 Mercury Mariner, making it a direct replacement option for rear glass support service on those models. StrongArm 6260 is also referenced under part number 6260 for catalog and search matching.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift action at the back window\u003c\/li\u003e\n\u003cli\u003eUneven support when opening the rear glass\u003c\/li\u003e\n\u003cli\u003eLoss of holding force in worn lift support cylinders\u003c\/li\u003e\n\u003cli\u003eNoise or rough movement from aging rear glass struts\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify ball socket size and compressed\/extended length before installation to confirm the correct rear glass lift support for your vehicle. For best results, replace lift supports in pairs so the rear glass opens and holds evenly. Confirm fitment for your exact Ford Escape, Mazda Tribute, or Mercury Mariner year before ordering, since this is a specific-fit part.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards to support smoother operation and longer service life. The brand also notes that lift supports are pressurized cylinders used in automotive hood, hatch, and rear glass applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617663090869,"sku":"BBZN-6260","price":22.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6260_Fro.jpg?v=1774984468"},{"product_id":"strongarm-6382-back-glass-lift-support","title":"StrongArm 6382 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 6382 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 6382 is a specific-fit back glass lift support for the rear window glass on select Jeep Liberty models. It uses a pressurized cylinder design to help hold the hatch glass in position and deliver smooth, controlled operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eFits 2009-2013 Jeep Liberty, hatch lift support models manufactured from 09\/29\/2008\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.09 in.; extended length: 17.34 in.; stroke length: 6.25 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 34.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 8 mm on one end and nylon 10 mm on the other\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for operating components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis StrongArm back glass lift support is engineered for the rear glass on Jeep Liberty hatch applications and cross-references Mopar 57010050AC for the same application. The 6382 part number is built as a specific-fit replacement with the correct compressed and extended dimensions, stroke length, and end fittings needed for proper rear glass support. StrongArm manufactures lift supports to tighter-than-standard specifications to promote consistent operation and long service life in automotive glass and hatch applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eHatch glass that drops unexpectedly\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support operation\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window glass movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle is a 2009-2013 Jeep Liberty with hatch lift support models manufactured from 09\/29\/2008 before ordering. Match the ball socket end sizes and overall length to the original support for correct fitment. Replace the support in pairs when the vehicle uses two supports to maintain balanced rear glass operation and safe holding force.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards for smoother operation and longer-lasting performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617671348405,"sku":"BBZN-6382","price":21.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6382_Fro.jpg?v=1774984497"},{"product_id":"strongarm-6487-back-glass-lift-support","title":"StrongArm 6487 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Grand Cherokee\u003c\/h2\u003e\u003cp\u003eStrongArm 6487 is a specific-fit back glass lift support for the 2011-2013 Jeep Grand Cherokee. It uses a pressurized cylinder design to help hold rear window glass in the open position with controlled movement and consistent support.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for the Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eCompressed length: 11.93 in.; extended length: 17.43 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.5 in. with a 39.0 maximum force rating\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable construction\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon angled 10 degree on one end and nylon 8 mm on the other\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials used in the support assembly\u003c\/li\u003e\n\u003cli\u003eStrongArm 6487 cross-references AMS Automotive 6487 and OE-style numbers including 68083884AA and 68083885AA\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 6487 is engineered for rear glass applications on the 2011, 2012, and 2013 Jeep Grand Cherokee. As a back glass lift support, it helps maintain the rear window in an open position while providing smooth, controlled operation during opening and closing. The specific-fit design, steel cylinder construction, and ball socket end fittings are matched to the application for direct replacement service. If you are searching for a 2011-2013 Jeep Grand Cherokee back glass lift support or StrongArm 6487 lift support, this part matches the listed vehicle fitment and dimensions.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support action\u003c\/li\u003e\n\u003cli\u003eHatch glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear window movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a worn lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke, and end fittings against the original support before installation. Confirm the ball socket angles and mounting points match the vehicle hardware on your Jeep Grand Cherokee. For balanced operation and even wear, lift supports are commonly replaced in pairs on the same rear glass application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer service life. This part number is built for the specified 2011-2013 Jeep Grand Cherokee rear glass application and follows the brand’s OE-style fitment approach.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617674199221,"sku":"BBZN-6487","price":20.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6487_Fro.jpg?v=1774984518"},{"product_id":"strongarm-6600-back-glass-lift-support","title":"StrongArm 6600 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 6600 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 6600 is a specific-fit back glass lift support for the 2000-2005 Ford Excursion. It uses a pressurized cylinder design to hold rear window glass in the open position and provide controlled movement during operation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit rear window glass lift support for Ford Excursion applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 9.94 in.; extended length: 13.94 in.; stroke length: 4.0 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 142.0\u003c\/li\u003e\n\u003cli\u003eSteel outer cylinder with black finish\u003c\/li\u003e\n\u003cli\u003eBall socket nylon ends, 10 mm at both ends\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smooth operation and wear resistance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eFits 2000-2005 Ford Excursion, N\/A. This StrongArm 6600 back glass lift support is built for rear window glass service on the Ford Excursion and is engineered to match the specified application. It cross-references AMS Automotive 6600 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or worn lift support pressure\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass movement\u003c\/li\u003e\n\u003cli\u003eNoisy operation from an aging lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke, end fittings, and force rating before installation. Match the 10 mm ball socket ends to the vehicle mounting points and confirm the support is positioned correctly for the rear glass. For safe, reliable operation, replace lift supports in pairs when the vehicle uses a matched left\/right setup.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life in automotive use.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617680785589,"sku":"BBZN-6600","price":18.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6600_Fro.jpg?v=1774984543"},{"product_id":"strongarm-6601-back-glass-lift-support","title":"StrongArm 6601 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 6601 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eStrongArm 6601 is a specific-fit back glass lift support for the 2005-2010 Jeep Grand Cherokee. It uses a pressurized cylinder design to hold rear window glass in the open position and deliver controlled movement during operation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific fit for 2005-2010 Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eCompressed length: 10.47 in.\u003c\/li\u003e\n\u003cli\u003eExtended length: 15.03 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 4.56 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force: 53.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: 8 mm nylon on one end, 10 mm nylon on the other\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eBuilt for Rear Glass Support\u003c\/h2\u003e\u003cp\u003eThis StrongArm back glass lift support is engineered for rear window glass applications where smooth opening and stable hold are required. The 6601 part number is a direct-fit replacement for the rear glass support used on the Jeep Grand Cherokee from 2005 through 2010, and it cross-references Monroe Shocks \u0026amp; Struts 172286 for the same application. StrongArm manufactures each lift support to meet demanding fitment and operating standards for consistent performance.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eSlow or uneven liftgate glass movement\u003c\/li\u003e\n\u003cli\u003eWeak support when opening the back window\u003c\/li\u003e\n\u003cli\u003eLoss of holding force in worn lift cylinders\u003c\/li\u003e\n\u003cli\u003eNoise or rough operation from aging lift support hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify fitment by year, make, and model before installation. For rear glass service on the Jeep Grand Cherokee, replace the support in the correct application position and confirm the ball socket end sizes match the vehicle mounting points. Check the lift action after installation to ensure the back glass opens and holds properly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that its lift supports are custom engineered and manufactured beyond industry standards for smoother operation and longer service life. The 6601 is built as a specific-fit replacement for the listed Jeep Grand Cherokee applications.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617680818357,"sku":"BBZN-6601","price":17.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6601_Fro.jpg?v=1774984544"},{"product_id":"strongarm-6602-back-glass-lift-support","title":"StrongArm 6602 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Jeep Wrangler\u003c\/h2\u003e\u003cp\u003eRestore smooth rear glass operation with this StrongArm back glass lift support, part number 6602. Built for 2007-2010 Jeep Wrangler applications, it provides the controlled lift and hold needed for rear window glass access on the Wrangler.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 2007-2010 Jeep Wrangler\u003c\/li\u003e\n\u003cli\u003eExtended length: 22.99 in; compressed length: 13.85 in\u003c\/li\u003e\n\u003cli\u003eStroke length: 9.14 in for measured opening and closing travel\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket (nylon) 10mm ends on both sides\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 28.0\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 6602\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 6602 is a specific-fit rear glass lift support engineered for the back glass on 2007-2010 Jeep Wrangler models. It uses pressurized cylinder construction to help support rear window glass during opening and closing, with dimensions and end fittings matched to the application for consistent operation. The steel outer cylinder, nylon ball socket ends, and low-friction material blend are selected to support smoother movement and durable service in daily use.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop C95330 for the same application. If you are searching for a Jeep Wrangler back glass lift support, rear window glass strut, or StrongArm 6602 replacement, this part is built for the listed Wrangler years and rear glass position.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support action at the back window\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass movement\u003c\/li\u003e\n\u003cli\u003eDifficulty opening the Jeep Wrangler rear glass\u003c\/li\u003e\n\u003cli\u003eLoss of support when accessing the cargo area through the back glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year before ordering: Fits 2007-2010 Jeep Wrangler, N\/A. Inspect the mounting ball studs and surrounding hardware for wear before installing the new support. For proper operation and balanced support, lift supports should be replaced in pairs when the vehicle uses two supports on the same opening.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smooth operation and long service life. Part number 6602 is built as a specific-fit replacement for the listed Jeep Wrangler rear glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617680851125,"sku":"BBZN-6602","price":17.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6602_Fro.jpg?v=1774984544"},{"product_id":"strongarm-6603-back-glass-lift-support","title":"StrongArm 6603 Back Glass Lift Support","description":"\u003ch2\u003eStrongArm 6603 Back Glass Lift Support\u003c\/h2\u003e\u003cp\u003eRestore controlled rear window glass movement on your Kia Sorento with the StrongArm 6603 back glass lift support. This specific-fit lift support is engineered for 2003-2009 Kia Sorento applications and uses a pressurized cylinder design for smooth opening and steady hold at the rear glass.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 2003-2009 Kia Sorento\u003c\/li\u003e\n\u003cli\u003eExtended length: 14.22 in.; compressed length: 8.97 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.25 in. with 24.0 maximum force\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable support performance\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 16-degree end and steel 10 mm end\u003c\/li\u003e\n\u003cli\u003eRubber and Teflon materials for smoother operation\u003c\/li\u003e\n\u003cli\u003eStrongArm part number 6603 for direct identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThe StrongArm 6603 is a rear window glass lift support built for the 2003-2009 Kia Sorento. It is a pressurized cylinder that helps hold the back glass in position while opening and closing, with dimensions and end fittings matched to the application for a specific fit. StrongArm manufactures each lift support beyond industry standards to support smoother operation and longer service life. This part cross-references AMS Automotive 6603 for the same application.\u003c\/p\u003e\u003cp\u003eWith a black steel outer cylinder, rubber and Teflon construction, and ball socket end fittings, this StrongArm 6603 lift support is built for consistent rear glass movement on the Kia Sorento. If your Sorento back glass no longer stays open or drops too quickly, this replacement addresses the worn support that commonly causes that condition.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open on a 2003-2009 Kia Sorento\u003c\/li\u003e\n\u003cli\u003eBack window glass that drops too quickly when lifted\u003c\/li\u003e\n\u003cli\u003eWeak or worn lift support pressure at the hatch glass\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass opening effort\u003c\/li\u003e\n\u003cli\u003eNoisy or rough rear glass movement caused by a failing support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the compressed length, extended length, stroke length, and end fittings before installation to match the original rear glass support. For safe and reliable operation, replace lift supports in pairs when servicing the rear glass system. Verify the ball socket attachment points on the Kia Sorento before removal and installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured to exceed industry standards for smoother operation and longer-lasting performance. The 6603 is built as a specific-fit replacement for the listed Kia Sorento applications and is identified by StrongArm part number 6603.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617680883893,"sku":"BBZN-6603","price":21.73,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6603_Fro.jpg?v=1774984544"},{"product_id":"strongarm-6605-back-glass-lift-support","title":"StrongArm 6605 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Lincoln Aviator\u003c\/h2\u003e\u003cp\u003eRestore controlled rear window glass movement with this StrongArm back glass lift support, part number 6605. It is a specific-fit replacement for 2003-2005 Lincoln Aviator models and is engineered for smooth operation and dependable support of the rear glass.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 2003-2005 Lincoln Aviator\u003c\/li\u003e\n\u003cli\u003eCompressed length: 13.35 in.; extended length: 19.1 in.; stroke length: 5.75 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 88.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: 8mm nylon on one end and 16-degree nylon on the other\u003c\/li\u003e\n\u003cli\u003eInner shaft diameter: 8.0; cylinder outside diameter: 19.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eStrongArm 6605 is a pressurized lift support built for rear window glass applications on the Lincoln Aviator. The specific-fit design helps ensure correct geometry and consistent operation, while the steel cylinder construction and internal sealing materials are selected for durable performance. If you are replacing a worn rear glass support on a 2003, 2004, or 2005 Lincoln Aviator, this part number 6605 provides the correct fitment for the back glass position.\u003c\/p\u003e\u003cp\u003eThis part cross-references AMS Automotive 6605 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Symptoms It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window glass dropping unexpectedly\u003c\/li\u003e\n\u003cli\u003eWeak or slow lift support movement\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass support\u003c\/li\u003e\n\u003cli\u003eNoise or binding when opening the rear glass\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the existing support length and end fittings before installation. The ball socket ends must match the vehicle mounting points, and the support should be installed in the correct orientation for smooth rear glass operation. For reliable support and balanced operation, replace lift supports in pairs when servicing the rear glass system.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life. Part number 6605 is built as a direct-fit replacement for the Lincoln Aviator rear glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617680949429,"sku":"BBZN-6605","price":18.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6605_Fro.jpg?v=1774984545"},{"product_id":"strongarm-6607-back-glass-lift-support","title":"StrongArm 6607 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Pathfinder\u003c\/h2\u003e\u003cp\u003eRestore controlled rear glass movement with this StrongArm back glass lift support, part number 6607. It is a specific-fit gas strut engineered for the 2005-2012 Nissan Pathfinder rear window glass, with dimensions and force calibrated for the application.\u003c\/p\u003e\u003cp\u003eStrongArm 6607 is built with a black steel outer cylinder, rubber and Teflon materials, and a 49.0 maximum force rating for smooth lift and steady hold. The specific-fit design helps maintain proper alignment on the Nissan Pathfinder back glass.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for 2005-2012 Nissan Pathfinder\u003c\/li\u003e\n\u003cli\u003eCompressed length: 10.125 in.; extended length: 15.239 in.\u003c\/li\u003e\n\u003cli\u003eStroke length: 5.114 in. for rear glass opening and closing travel\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder for durable construction\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 16 degree and observatory 10 mm\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 49.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eThis StrongArm back glass lift support, part number 6607, is a pressurized cylinder used to support rear window glass on the Nissan Pathfinder. It is engineered for the 2005-2012 Nissan Pathfinder and cross-references Monroe Shocks \u0026amp; Struts 172286 and 182286 for the same application. The design uses a steel outer cylinder with rubber and Teflon materials to support consistent operation and reduced wear over time.\u003c\/p\u003e\u003ch2\u003eCommon Replacement Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass drops instead of staying open\u003c\/li\u003e\n\u003cli\u003eBack window opens slowly or feels heavy\u003c\/li\u003e\n\u003cli\u003eLift support loses pressure and no longer holds position\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass movement\u003c\/li\u003e\n\u003cli\u003eVisible wear at the ball socket ends or cylinder body\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the compressed length, extended length, stroke length, and end fittings before installation to confirm the correct rear glass support for your Nissan Pathfinder. Inspect the mounting points and ball studs for wear or damage before attaching the new support. For safe, reliable support of the rear glass, replace lift supports in pairs when the vehicle uses two supports.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm states that each lift support is custom engineered and manufactured beyond industry standards to deliver smoother operation and longer service life. Part number 6607 is built as a specific-fit replacement for the 2005-2012 Nissan Pathfinder back glass application.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617681014965,"sku":"BBZN-6607","price":19.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6607_Fro.jpg?v=1774984545"},{"product_id":"strongarm-6609-back-glass-lift-support","title":"StrongArm 6609 Back Glass Lift Support","description":"\u003ch2\u003eBack Glass Lift Support for Explorer and Mountaineer\u003c\/h2\u003e\u003cp\u003eStrongArm 6609 is a specific-fit back glass lift support for the rear window glass on the 2004 Ford Explorer and 2004 Mercury Mountaineer built from 07\/2002. It provides controlled lift and hold for rear glass operation, with dimensions and force matched to the application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSpecific-fit back glass lift support for rear window glass applications\u003c\/li\u003e\n\u003cli\u003eCompressed length: 12.5 in.; extended length: 18.5 in.; stroke length: 6.0 in.\u003c\/li\u003e\n\u003cli\u003eMaximum force rating: 85.0\u003c\/li\u003e\n\u003cli\u003eBlack steel outer cylinder with rubber and Teflon materials\u003c\/li\u003e\n\u003cli\u003eBall socket ends: nylon 8mm on one end and nylon 16-degree on the other\u003c\/li\u003e\n\u003cli\u003eNo internal rebound spring\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eStrongArm 6609 is engineered as a rear glass lift support for vehicles that use a pressurized cylinder to hold the back glass in the open position. The 19.0 mm cylinder outside diameter and 8.0 mm inner shaft diameter support consistent operation, while the 85.0 force rating helps maintain proper rear glass movement. This part cross-references AMS Automotive 6609 for the same application. StrongArm 6609 is listed for 2004 Ford Explorer and 2004 Mercury Mountaineer, making it a direct replacement choice for rear window glass service on these models.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear glass that will not stay open\u003c\/li\u003e\n\u003cli\u003eBack window glass that drops too quickly\u003c\/li\u003e\n\u003cli\u003eWeak or worn lift support pressure\u003c\/li\u003e\n\u003cli\u003eUneven or inconsistent rear glass movement\u003c\/li\u003e\n\u003cli\u003eNoise or binding from a fatigued lift support\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle build date before ordering: this application is listed for 2004 Ford Explorer and 2004 Mercury Mountaineer from 07\/2002. Confirm end fittings, compressed length, and extended length against the original support before installation. Rear glass lift supports are commonly replaced when the lift action becomes weak or unstable, and the vehicle should be supported safely during service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eStrongArm lift supports are custom engineered and manufactured beyond industry standards for smoother operation and longer service life. Part number 6609 is built for specific-fit rear glass applications and is matched to the listed vehicle fitment for consistent replacement performance.\u003c\/p\u003e","brand":"StrongArm","offers":[{"title":"Default Title","offer_id":43617681047733,"sku":"BBZN-6609","price":16.73,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/Z1_6609_Fro.jpg?v=1774984546"}],"url":"https:\/\/www.partcatalog.com\/collections\/glass-windows-and-related-components.oembed?page=6","provider":"PartCatalog","version":"1.0","type":"link"}