{"title":"Steering \u003e Hardware, Fasteners and Fittings","description":"\u003cp\u003eSteering hardware, fasteners, and fittings are the small parts that hold your steering system's geometry in place and keep fluid where it belongs. Tie rod end adjusting sleeves set your front-end alignment after tie rod replacement — worn or seized ones make precise toe adjustment impossible. King pin sets are critical on older trucks and heavy-duty applications where ball joints aren't used; expect replacement every 80,000–150,000 miles depending on load and lubrication habits. Power steering reservoir caps, return line fittings, and pump hardware address leaks and contamination that quietly degrade assist performance. When buying, verify torque specs and thread pitch against your factory service manual — a mismatched sleeve or bolt can strip threads or allow joint movement. For adjusting sleeves, check clamp bolt diameter and thread count (typically 7\/8\"-20 or 1\"-20 on domestic trucks). OEM parts are worth it on king pin sets for heavy-duty rigs; quality aftermarket works fine for most import and light-duty applications.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eToe alignment won't hold after a recent tie rod job.\u003c\/strong\u003e If your alignment walks out within a few thousand miles, inspect the adjusting sleeve — corrosion or a stripped clamp bolt can prevent it from locking the adjustment.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLoose, clunking, or wandering steering on an older truck or SUV.\u003c\/strong\u003e King pin wear causes vague, darty steering and visible play when you grab the wheel at 9 and 3 o'clock; worn pins typically show more than 1\/8\" of vertical play at the wheel.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePower steering fluid level drops with no visible hose leak.\u003c\/strong\u003e A cracked or deteriorated reservoir cap seal or a weeping return line end fitting is often the source — look for residue around the cap neck or at the fitting crimp.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSteering column rattle or wobble at highway speed.\u003c\/strong\u003e A loose or damaged column lock bolt or column bolt can allow the shaft to shift under load, creating noise and imprecise feel.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVisible rust, stripped threads, or seized hardware during other steering work.\u003c\/strong\u003e Replacing a tie rod end or drag link but leaving a corroded adjusting sleeve behind is a shortcut that makes the next alignment job harder and less accurate.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDo I need to replace the adjusting sleeve when I replace tie rod ends?\u003c\/strong\u003e Not always, but it's strongly recommended if the sleeve shows rust, elongated clamp slots, or stripped threads. A new tie rod end paired with a compromised sleeve won't hold alignment accurately. Sleeves are inexpensive — typically $8–$25 — and replacing both at the same time saves a re-alignment visit later.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eAre aftermarket king pin sets as reliable as OEM for heavy-duty trucks?\u003c\/strong\u003e Quality-tier aftermarket brands (Moog, Federal-Mogul) are generally comparable for light-to-medium duty. For 3\/4-ton and 1-ton trucks used for towing or off-road, OEM or heavy-duty greaseable aftermarket sets are worth the premium. Always confirm the kit includes bushings, thrust bearings, and all required hardware — some budget kits omit critical pieces.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat's involved in replacing a power steering return line end fitting, and what else should I do at the same time?\u003c\/strong\u003e Most fittings are a straightforward flare-nut or compression swap, running $10–$40 for the part. While the system is open, flush the fluid and inspect the reservoir cap seal and the high-pressure line for cracking. Refill with the manufacturer-specified fluid type — mixing ATF and dedicated PS fluid can damage seals.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"beck-arnley-101-6528-steering-tie-rod-end-adjusting-sleeve","title":"Beck Arnley 101-6528 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eOverview of Beck Arnley Steering Tie Rod End Adjusting Sleeve\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 101-6528 steering tie rod end adjusting sleeve is designed specifically for Toyota 4Runner, Pickup, and T100 models. This component plays a critical role in maintaining proper steering alignment and vehicle handling.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with Toyota 4Runner, Pickup, and T100 models\u003c\/li\u003e\n\u003cli\u003ePart number 101-6528 ensures precise fitment\u003c\/li\u003e\n\u003cli\u003eDurable construction for reliable steering performance\u003c\/li\u003e\n\u003cli\u003eEssential for adjusting tie rod end length during alignment\u003c\/li\u003e\n\u003cli\u003eCorrosion-resistant finish for extended service life\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 101-6528 adjusting sleeve is engineered to meet OEM specifications for Toyota vehicles including the 4Runner, Pickup, and T100. This steering tie rod end adjusting sleeve allows for accurate adjustment of the tie rod ends, which is necessary to maintain proper wheel alignment and steering geometry. Manufactured with quality materials, it resists wear and corrosion, ensuring consistent performance over time. The part number 101-6528 corresponds to a precise fit that supports the steering system's integrity and safety.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cp\u003eThis adjusting sleeve is used primarily during steering system repairs and alignments. It addresses several common issues:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects improper toe alignment caused by worn or damaged sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive steering play or looseness\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear due to misalignment\u003c\/li\u003e\n\u003cli\u003eFacilitates precise steering adjustments after suspension work\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and vehicle control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Toyota 4Runner, Pickup, or T100 before installation\u003c\/li\u003e\n\u003cli\u003eUse proper tools to avoid damaging threads during adjustment\u003c\/li\u003e\n\u003cli\u003ePerform a full wheel alignment after installation to verify correct settings\u003c\/li\u003e\n\u003cli\u003eInspect adjacent steering components for wear or damage\u003c\/li\u003e\n\u003cli\u003eFollow manufacturer torque specifications for secure fitting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are manufactured to meet or exceed OEM standards, providing reliable performance for Toyota steering systems. The 101-6528 adjusting sleeve undergoes rigorous quality control to ensure durability and fitment accuracy. While specific warranty details may vary, Beck Arnley typically offers coverage against defects in materials and workmanship, supporting long-term vehicle safety and function.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388416360629,"sku":"BBGB-101-6528","price":23.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_1016528_Oth_5b0073c4-54ac-4b4a-aff1-227b6ac6aebb.jpg?v=1774711446"},{"product_id":"delphi-ta2146-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2146 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2146 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on select Ford, Lincoln, and Mercury vehicles. Constructed from high strength steel with a fine thread design, this black adjusting sleeve ensures reliable performance and durability for your steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 242.0 mm (9.528 inches)\u003c\/li\u003e\n\u003cli\u003eFine thread type with 16.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for easy installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003cli\u003eCompatible with Ford, Lincoln, Mercury models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2146 adjusting sleeve is designed to provide accurate steering tie rod end adjustments, essential for maintaining proper wheel alignment and steering response. Its black finish offers corrosion resistance, while the fine thread type and 16.0 mm diameter ensure a secure fit. The included mounting hardware simplifies installation, making it a practical replacement part. This standard grade component is suitable for routine maintenance and repairs on vehicles requiring a reliable steering tie rod end adjusting sleeve.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with a range of Ford, Lincoln, and Mercury models, including:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFord Crown Victoria, LTD, LTD Crown Victoria\u003c\/li\u003e\n\u003cli\u003eLincoln Continental, Mark VI, Town Car\u003c\/li\u003e\n\u003cli\u003eMercury Colony Park, Grand Marquis, Marquis\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUsing the Delphi TA2146 ensures proper fitment and function for these specific vehicles.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment problems\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged tie rod end adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates steering play and improves handling\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear caused by misalignment\u003c\/li\u003e\n\u003cli\u003eRestores precise steering response\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA2146 adjusting sleeve requires basic steering system knowledge and tools. The included mounting hardware facilitates secure attachment. It is recommended to perform a wheel alignment after installation to ensure optimal steering performance. Inspect related steering components for wear during replacement to maintain overall system integrity.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2146 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent quality and durability. The part is backed by Delphi's quality control processes. Please refer to Delphi's official warranty terms for coverage details.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388723724469,"sku":"BBMX-TA2146","price":21.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2146_Ang.jpg?v=1774723877"},{"product_id":"delphi-ta2147-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2147 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2147 Steering Tie Rod End Adjusting Sleeve is engineered for reliable steering system adjustments on select GM vehicles. Constructed from high strength steel with a fine thread design, this black adjusting sleeve ensures precise alignment and durability for front steering components.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high strength steel for enhanced durability\u003c\/li\u003e\n\u003cli\u003eLength of 120 mm (4.724 inches) for accurate fitment\u003c\/li\u003e\n\u003cli\u003eFine thread type with 18 mm thread diameter for secure adjustments\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade suitable for front steering positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA2147 adjusting sleeve by Delphi is designed to meet the demands of steering hardware, fasteners, and fittings for front-end applications. Its black finish provides corrosion resistance, while the fine thread ensures smooth and precise tie rod end adjustments. With a length of 120 mm (4.724 inches) and an 18 mm thread diameter, this sleeve fits a range of vehicles including Buick, Cadillac, Chevrolet, GMC, and Oldsmobile models such as the Silverado 1500, Tahoe, Escalade, and more. The included mounting hardware simplifies installation and helps maintain proper steering alignment.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with various GM trucks and SUVs, including:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eChevrolet Silverado 1500, 2500, 3500 series\u003c\/li\u003e\n\u003cli\u003eGMC Sierra 1500, 2500, 3500 series\u003c\/li\u003e\n\u003cli\u003eCadillac Escalade and Fleetwood\u003c\/li\u003e\n\u003cli\u003eBuick Roadmaster and Oldsmobile models\u003c\/li\u003e\n\u003cli\u003eOther models such as Astro, Blazer, Suburban, Tahoe, and Yukon\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Issues Addressed by the TA2147 Adjusting Sleeve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment due to worn or damaged tie rod ends\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper toe settings during wheel alignment\u003c\/li\u003e\n\u003cli\u003eExcessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eCorrosion or thread damage affecting adjustment capability\u003c\/li\u003e\n\u003cli\u003eReplacement of damaged or stripped adjusting sleeves\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA2147 adjusting sleeve, ensure the following:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with your specific make and model before installation\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware to secure the sleeve properly\u003c\/li\u003e\n\u003cli\u003eApply anti-seize lubricant on threads to prevent corrosion and ease future adjustments\u003c\/li\u003e\n\u003cli\u003ePerform a professional wheel alignment after installation to ensure proper steering geometry\u003c\/li\u003e\n\u003cli\u003eInspect adjacent steering components for wear or damage during replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2147 adjusting sleeve to meet standard replacement grade specifications, ensuring reliable performance in steering applications. The part is constructed from high strength steel and undergoes quality control to maintain durability and fitment accuracy. Warranty coverage details should be confirmed with the point of purchase or Delphi directly.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388723757237,"sku":"BBMX-TA2147","price":19.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2147_Ang.jpg?v=1774723877"},{"product_id":"delphi-ta2148-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2148 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2148 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on select Ford, Lincoln, and Mercury vehicles. Designed with high strength steel and a fine thread type, this component ensures reliable performance and durability for front steering systems.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 11.969 inches (304.0 mm)\u003c\/li\u003e\n\u003cli\u003eBlack finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eFine thread type with 16.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for front position tie rod ends\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2148 adjusting sleeve is a critical component in the steering assembly, specifically designed for front tie rod end adjustments. Its high strength steel construction provides the necessary rigidity and wear resistance required for maintaining proper steering alignment. The fine thread type with a 16.0 mm diameter allows for precise tuning of the tie rod length, which is essential for accurate wheel alignment and vehicle handling. The black finish offers additional protection against environmental factors, extending the service life of the part. This sleeve is compatible with Ford Crown Victoria, Lincoln Town Car, and Mercury Grand Marquis models, ensuring a proper fit and function.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with the following makes and models:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFord Crown Victoria\u003c\/li\u003e\n\u003cli\u003eLincoln Town Car\u003c\/li\u003e\n\u003cli\u003eMercury Grand Marquis\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt is designed for use in the front steering system, providing a reliable connection and adjustment point for tie rod ends.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by the TA2148 Adjusting Sleeve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment due to worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper toe settings on front wheels\u003c\/li\u003e\n\u003cli\u003eExcessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eCorrosion or thread damage affecting adjustment capability\u003c\/li\u003e\n\u003cli\u003eReplacement of standard grade components to restore steering precision\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the vehicle is securely lifted and supported before installation\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware to secure the sleeve properly\u003c\/li\u003e\n\u003cli\u003eVerify thread compatibility and clean threads before assembly\u003c\/li\u003e\n\u003cli\u003eAdjust tie rod length carefully to maintain factory alignment specifications\u003c\/li\u003e\n\u003cli\u003eAfter installation, perform a professional wheel alignment check\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2148 is manufactured to meet standard replacement grade specifications, ensuring consistent quality and performance. Constructed from high strength steel and finished in black for corrosion resistance, this part is designed to provide reliable service in front steering applications. While specific warranty details are not provided, Delphi parts typically adhere to industry standards for durability and fitment.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388723790005,"sku":"BBMX-TA2148","price":24.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2148_Ang.jpg?v=1774723877"},{"product_id":"delphi-ta2180-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2180 Steering Tie Rod End Adjusting Sleeve - Left","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2180 Steering Tie Rod End Adjusting Sleeve is engineered for reliable steering performance in select Dodge, Ford, Jeep, and Mazda vehicles. Constructed from high strength steel with a fine thread design, this black adjusting sleeve ensures precise alignment and durability for your steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high strength steel for enhanced durability\u003c\/li\u003e\n\u003cli\u003eLength options: 127.0 mm (5.0 inches) for accurate fitment\u003c\/li\u003e\n\u003cli\u003eFine thread type with 20.0 mm thread diameter for secure adjustment\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade suitable for left-side steering applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2180 adjusting sleeve is a critical component in the steering hardware assembly, designed to provide precise tie rod end adjustments. Its high strength steel construction offers resistance to wear and corrosion, maintaining steering integrity over time. The fine thread type and 20.0 mm diameter allow for smooth and accurate alignment adjustments, essential for maintaining proper steering geometry. This part is finished in black, providing a corrosion-resistant surface that complements the vehicle’s undercarriage. Included mounting hardware simplifies installation, reducing downtime during repairs or replacements.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with a range of Dodge, Ford, Jeep, and Mazda models, including but not limited to:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDodge Ram 1500, Ram 2500, Ram 3500, Dakota, and Durango\u003c\/li\u003e\n\u003cli\u003eFord F-100, F-150, F-250, F-350, Bronco, Bronco II, Explorer, Ranger\u003c\/li\u003e\n\u003cli\u003eJeep Cherokee, Wagoneer, Comanche\u003c\/li\u003e\n\u003cli\u003eMazda B2300, B3000, B4000, Navajo\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIts design specifically fits left-side steering assemblies, ensuring compatibility with these vehicle models for effective steering adjustments.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by the TA2180 Adjusting Sleeve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment causing uneven tire wear\u003c\/li\u003e\n\u003cli\u003eLoose or worn tie rod ends affecting steering responsiveness\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper toe settings after suspension repairs\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage to existing adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eReplacement of damaged or stripped threads in steering linkage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify vehicle compatibility with the Delphi TA2180 part number before installation\u003c\/li\u003e\n\u003cli\u003eUse included mounting hardware to ensure secure fitment\u003c\/li\u003e\n\u003cli\u003eApply anti-seize lubricant on threads to prevent corrosion and ease future adjustments\u003c\/li\u003e\n\u003cli\u003eAfter installation, perform a professional wheel alignment to ensure proper steering geometry\u003c\/li\u003e\n\u003cli\u003eInspect adjacent steering components for wear or damage during replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2180 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent performance and durability. The part undergoes rigorous quality control to comply with OEM standards. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects. Consult product documentation or authorized sources for exact warranty terms.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388724707509,"sku":"BBMX-TA2180","price":27.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2180_Ang.jpg?v=1774723885"},{"product_id":"delphi-ta2269-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2269 Steering Tie Rod End Adjusting Sleeve - At Pitman Arm, Left or Right","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2269 Steering Tie Rod End Adjusting Sleeve is engineered for reliable steering performance on select Ford, Jeep, and Mazda vehicles. Constructed from high strength steel with a fine thread design, this black adjusting sleeve ensures precise alignment adjustments and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 126.0 mm (4.961 inches)\u003c\/li\u003e\n\u003cli\u003eFine thread type with 22.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for easy installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for right-side position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA2269 adjusting sleeve is designed to provide a secure connection between the steering tie rod end and the steering linkage. Its fine thread type and 22.0 mm diameter allow for precise steering adjustments, critical for maintaining proper wheel alignment. The black finish offers corrosion resistance, while the included mounting hardware simplifies installation. This part is a standard replacement grade, suitable for right-side applications on various models.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Fitment\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with a range of Ford, Jeep, and Mazda models, including Ford B2300, B3000, B4000, Bronco, Bronco II, E-150 series, E-250, E-350 series, Explorer, F-100, F-150, F-250, F-350, Jeep Grand Cherokee, Grand Wagoneer, Navajo, Ranger, TJ, Wrangler, and Mazda models. The TA2269 part number ensures correct fitment for these vehicles, supporting proper steering system function.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Resolution\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores proper steering alignment and handling\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves causing steering play\u003c\/li\u003e\n\u003cli\u003eEliminates uneven tire wear due to misalignment\u003c\/li\u003e\n\u003cli\u003ePrevents steering linkage looseness and vibration\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable vehicle control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA2269 adjusting sleeve requires basic steering system knowledge and tools. The included mounting hardware facilitates secure attachment. It is important to verify the right-side position before installation and to perform a wheel alignment after replacement to ensure optimal steering performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2269 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent quality and durability. The high strength steel construction and fine thread design contribute to long service life. Warranty details should be confirmed with the parts provider, as coverage may vary.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388729917621,"sku":"BBMX-TA2269","price":31.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2269_Fro.jpg?v=1774723906"},{"product_id":"delphi-ta2561-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2561 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2561 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering alignment on select Toyota models. Designed with high strength steel and a fine thread type, this component ensures reliable performance and durability for your Toyota 4Runner, Pickup, and T100 vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength of 120 mm (4.72 inches) for exact fitment\u003c\/li\u003e\n\u003cli\u003eBlack finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eFine thread type with 17 mm diameter for secure adjustment\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA2561 adjusting sleeve is a critical component in the steering system, providing the necessary adjustment range for tie rod ends. Its 120 mm length and fine 17 mm thread diameter allow for precise alignment adjustments, essential for maintaining proper steering geometry. The black coating offers protection against rust and wear, extending the service life of the part. Included mounting hardware simplifies the installation process, reducing downtime during repairs or replacements.\u003c\/p\u003e\u003ch2\u003eCompatible Toyota Models and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Toyota 4Runner, Pickup, and T100 models. It is designed to meet the specifications required for these vehicles, ensuring proper fit and function. Use the Delphi TA2561 when replacing worn or damaged adjusting sleeves to restore steering accuracy and vehicle handling.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in the steering linkage\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear caused by improper alignment\u003c\/li\u003e\n\u003cli\u003eRestores smooth and responsive steering control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA2561 adjusting sleeve requires basic mechanical skills and proper tools. Ensure the vehicle is securely lifted and the steering components are accessible. Use the included mounting hardware to secure the sleeve, and verify thread engagement to avoid cross-threading. After installation, perform a full steering alignment to confirm correct adjustment and safe vehicle operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2561 adjusting sleeve to meet standard replacement grade requirements, ensuring consistent quality and reliability. The part undergoes rigorous testing to comply with OEM specifications. While specific warranty details may vary, Delphi products typically include coverage against manufacturing defects. Consult product documentation or supplier information for exact warranty terms.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388743844021,"sku":"BBMX-TA2561","price":19.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2561_Fro.jpg?v=1774723961"},{"product_id":"delphi-ta2610-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2610 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2610 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on select Saab vehicles. Designed with durable steel construction and fine threading, this component ensures reliable performance for front steering systems on Saab 9-3 and 900 models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength of 105.0 mm (4.134 inches) for exact fitment\u003c\/li\u003e\n\u003cli\u003eBlack finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eFine thread type with 0.63 inch (16.0 mm) diameter for secure adjustment\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade suitable for front steering positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2610 adjusting sleeve is a critical hardware component in the steering assembly, specifically designed to connect and adjust the tie rod ends on Saab 9-3 and 900 models. Its steel material provides the necessary strength to withstand steering forces and road conditions. The fine thread type and precise thread diameter allow for smooth and accurate alignment adjustments, which are essential for maintaining proper steering geometry and vehicle handling. The black coating offers additional protection against rust and wear, extending the service life of the part.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Resolution\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged tie rod end adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and handling\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in the steering linkage\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of connected steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA2610 requires proper tools to ensure the fine threads are not damaged during adjustment. It is recommended to verify thread compatibility and length before installation. After fitting, a professional alignment check is advised to confirm correct steering geometry. Use anti-seize lubricant on threads if necessary to facilitate future adjustments and prevent corrosion.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts meet industry standards for material quality and manufacturing precision. The TA2610 adjusting sleeve is a standard replacement grade component designed to meet OEM specifications for Saab 9-3 and 900 front steering systems. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to ensure reliability and customer confidence.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388744761525,"sku":"BBMX-TA2610","price":17.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2610_Ang.jpg?v=1774723968"},{"product_id":"delphi-ta2754-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA2754 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2754 steering tie rod end adjusting sleeve is designed for precise steering adjustments on the Scion iQ. Crafted from durable steel and finished in black, this standard replacement part ensures reliable performance and fitment for your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 17.047 inches (433.0 mm) for accurate fit\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.551 inches (14.0 mm) for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for dependable steering adjustments\u003c\/li\u003e\n\u003cli\u003eCompatible specifically with Scion iQ models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Delphi TA2754 adjusting sleeve is engineered to meet OEM specifications for the Scion iQ steering system. Its steel construction provides the necessary strength to withstand steering forces and road conditions. The black finish offers corrosion resistance, extending the part's service life. With a length of 17.047 inches (433.0 mm) and a thread diameter of 0.551 inches (14.0 mm), this sleeve ensures a precise fit and secure connection between the tie rod end and steering linkage. Note that mounting hardware is not included with this part.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Scion iQ models, making it a suitable replacement for worn or damaged sleeves in the steering assembly. Use this part to maintain proper alignment and steering response in your Scion iQ.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering play and improves handling\u003c\/li\u003e\n\u003cli\u003eReplaces damaged or corroded adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eRestores proper tie rod end alignment\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear caused by misalignment\u003c\/li\u003e\n\u003cli\u003eEnsures safe and responsive steering control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA2754 adjusting sleeve requires basic steering system knowledge and appropriate tools. Ensure the vehicle is securely lifted and supported before beginning. Since mounting hardware is not included, retain or replace any necessary fasteners during installation. Proper torque specifications should be followed to avoid damage or loosening. After installation, a professional wheel alignment is recommended to optimize steering performance and tire wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA2754 adjusting sleeve to meet industry standards for steering components. This standard replacement part undergoes quality checks to ensure durability and fitment accuracy. While specific warranty details are not provided, Delphi parts typically come with a limited warranty against defects in materials and workmanship. Consult the product documentation or Delphi for warranty terms.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388748038325,"sku":"BBMX-TA2754","price":55.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA2754_Ang.jpg?v=1774723988"},{"product_id":"delphi-ta5457-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5457 Steering Tie Rod End Adjusting Sleeve - Left","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5457 steering tie rod end adjusting sleeve is engineered for precise steering adjustments on select Ford and Lincoln vehicles. Constructed from durable steel with a fine thread design, this black, 115 mm length sleeve ensures reliable fitment and performance for your steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 115.0 mm (4.528 inches) for accurate fit\u003c\/li\u003e\n\u003cli\u003eFine thread type with 18.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for left-side installation\u003c\/li\u003e\n\u003cli\u003eCompatible with Ford and Lincoln models including F-150, F-250, Expedition, Navigator, and Blackwood\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5457 adjusting sleeve is designed to provide a secure connection between the steering tie rod end and the steering linkage. Its fine thread type and 18 mm diameter allow for precise alignment adjustments, critical for maintaining proper steering geometry. The black finish offers corrosion resistance, while the steel construction ensures strength under typical driving conditions. This part is intended as a standard replacement for the left position on compatible vehicles, including Ford F-150, F-250, Expedition, Lincoln Navigator, and Blackwood models.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues caused by worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and handling\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of tie rod ends and related components\u003c\/li\u003e\n\u003cli\u003eAddresses uneven tire wear linked to steering misalignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the vehicle is securely lifted and supported before installation\u003c\/li\u003e\n\u003cli\u003eUse appropriate tools to avoid damaging the fine threads during removal and installation\u003c\/li\u003e\n\u003cli\u003eVerify left-side placement as specified for this part number TA5457\u003c\/li\u003e\n\u003cli\u003eAfter installation, perform a professional wheel alignment to optimize steering performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts meet industry standards for material and manufacturing quality. The TA5457 adjusting sleeve is a standard replacement grade component designed to meet OEM specifications. While specific warranty terms may vary, Delphi typically offers coverage against manufacturing defects to ensure reliability and customer confidence.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388806889653,"sku":"BBMX-TA5457","price":21.06,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5457_Fro_13602a55-ffd6-4db3-8e7a-f5e46dccb5dc.jpg?v=1774724179"},{"product_id":"delphi-ta5458-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5458 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5458 steering tie rod end adjusting sleeve is a precision-engineered component designed for reliable steering performance. Compatible with Chevrolet, Oldsmobile, and Pontiac models such as the Bel Air, Camaro, and Firebird, this steel sleeve ensures proper alignment and secure fitment.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from durable steel material for strength and longevity\u003c\/li\u003e\n\u003cli\u003eLength of 153.0 mm (6.024 inches) for exact fitment\u003c\/li\u003e\n\u003cli\u003eBlack finish for corrosion resistance and durability\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eRegular grade type with fine thread and 18.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for dependable performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5458 steering tie rod end adjusting sleeve is manufactured to meet OEM specifications, providing a reliable connection between the steering tie rod and the steering knuckle. Made from high-quality steel, this sleeve offers the necessary strength to withstand steering forces and road conditions. Its fine thread type and 18.0 mm thread diameter allow for precise adjustments, ensuring proper wheel alignment and steering response. The black coating adds a layer of protection against rust and wear, extending the service life of the component. This part is compatible with a range of classic and modern vehicles, including Chevrolet C10 Suburban, Oldsmobile Omega, and Pontiac Nova models.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores proper steering alignment on Chevrolet Bel Air and Camaro vehicles\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves in Pontiac Firebird and Oldsmobile Omega\u003c\/li\u003e\n\u003cli\u003eEliminates steering play caused by loose or corroded tie rod connections\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear due to misaligned steering components\u003c\/li\u003e\n\u003cli\u003eEnsures secure mounting with included hardware for Chevrolet Caprice and Impala\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with your specific vehicle make and model before installation\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware to ensure a secure fit\u003c\/li\u003e\n\u003cli\u003eApply anti-seize lubricant on threads to facilitate future adjustments\u003c\/li\u003e\n\u003cli\u003eCheck steering alignment after installation to confirm proper adjustment\u003c\/li\u003e\n\u003cli\u003eConsult a professional mechanic if unsure about installation procedures\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts are manufactured to meet industry standards for quality and durability. The TA5458 steering tie rod end adjusting sleeve is a standard replacement grade component, designed to provide consistent performance. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects. Always refer to the product documentation or contact the manufacturer for precise warranty information.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388806955189,"sku":"BBMX-TA5458","price":17.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5458_Fro_cc8bc4df-8e1d-4da9-820d-431a2e2a8879.jpg?v=1774724179"},{"product_id":"delphi-ta5479-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5479 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5479 Steering Tie Rod End Adjusting Sleeve is a precision-engineered component designed for reliable steering system adjustments. Constructed from durable steel with a fine thread type, this black adjusting sleeve ensures secure fitment and consistent performance for various Chevrolet, Dodge, Ford, GMC, Jeep, and Plymouth models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength of 115.0 mm (4.528 inches) for precise fitment\u003c\/li\u003e\n\u003cli\u003eFine thread type with 18.0 mm thread diameter for accurate adjustments\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade suitable for pitman arm to steering arm connections\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5479 adjusting sleeve is designed specifically for steering tie rod end adjustments, positioned at the pitman arm, front left outer side, connecting the pitman arm to the steering arm. Its steel construction provides the necessary rigidity and resistance to wear, while the fine thread ensures smooth and precise alignment adjustments. The black finish offers corrosion resistance, extending the service life of the part. This component is compatible with a wide range of vehicles including Chevrolet Blazer, Dodge Ram 2500 Van, Ford F-150, GMC Jimmy, Jeep Cherokee, and Plymouth V20 models, among others.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment and uneven tire wear\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves to restore steering precision\u003c\/li\u003e\n\u003cli\u003eEliminates looseness or play in the steering linkage\u003c\/li\u003e\n\u003cli\u003ePrevents steering component binding or stiffness\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable vehicle handling\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with your specific vehicle make and model before installation\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware for secure attachment\u003c\/li\u003e\n\u003cli\u003eApply anti-seize lubricant on threads to facilitate future adjustments\u003c\/li\u003e\n\u003cli\u003eVerify proper torque specifications to avoid over-tightening\u003c\/li\u003e\n\u003cli\u003ePerform a wheel alignment after installation to ensure optimal steering performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts meet industry standards for quality and durability. The TA5479 adjusting sleeve is a standard replacement grade component designed to maintain OEM specifications. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to ensure customer confidence in product reliability.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388808233141,"sku":"BBMX-TA5479","price":19.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5479_Fro.jpg?v=1774724185"},{"product_id":"delphi-ta5516-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5516 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5516 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering alignment on select front-end vehicles. Constructed from durable steel with a fine thread design, this black adjusting sleeve ensures reliable fitment and adjustment for various Buick, Chevrolet, Ford, GMC, Mercury, Oldsmobile, and Pontiac models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength of 114.5 mm (4.508 inches) for accurate fit\u003c\/li\u003e\n\u003cli\u003eFine thread type with 0.625 inch (15.875 mm) diameter\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for front position tie rod ends\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5516 adjusting sleeve is designed to provide a secure connection between the steering tie rod end and the steering linkage. Its fine thread ensures precise adjustment capability, which is critical for maintaining proper wheel alignment and steering response. The steel construction offers resistance to wear and corrosion, while the black finish adds an extra layer of protection. This part is compatible with front steering assemblies on a range of vehicles including the Chevrolet Blazer, Camaro, El Camino, and S10, as well as Buick models like the Century and Regal, Ford’s Thunderbird, and Pontiac’s GTO and Firebird.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment caused by worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in the steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering geometry for improved handling\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of tie rod ends and related components\u003c\/li\u003e\n\u003cli\u003eFacilitates accurate toe-in adjustment during suspension repairs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the vehicle is securely lifted and supported before installation\u003c\/li\u003e\n\u003cli\u003eRemove old adjusting sleeve carefully to avoid damaging adjacent components\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware to secure the sleeve firmly\u003c\/li\u003e\n\u003cli\u003eVerify thread engagement and alignment before final tightening\u003c\/li\u003e\n\u003cli\u003eAfter installation, perform a professional wheel alignment to confirm proper adjustment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi TA5516 is manufactured to meet standard replacement grade specifications, ensuring consistent performance and durability. The part undergoes rigorous quality control to comply with OEM standards. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to provide confidence in product reliability.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388810854581,"sku":"BBMX-TA5516","price":17.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5516_Fro.jpg?v=1774724195"},{"product_id":"delphi-ta5541-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5541 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5541 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on select Chrysler and Dodge vehicles. Constructed from durable steel with a fine thread design, this black adjusting sleeve ensures reliable performance and fitment for front steering components.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 3.37 inches (85.5 mm)\u003c\/li\u003e\n\u003cli\u003eColor: Black finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eThread Type: Fine thread with 18.0 mm diameter\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for easy installation\u003c\/li\u003e\n\u003cli\u003eGrade Type: Regular, standard replacement quality\u003c\/li\u003e\n\u003cli\u003ePosition: Designed for front steering applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5541 adjusting sleeve is a standard replacement part designed specifically for front steering tie rod ends. Its steel construction provides the necessary strength to maintain alignment settings under normal driving conditions. The fine thread type with an 18.0 mm diameter allows for precise adjustments, critical for maintaining proper steering geometry. The black finish offers additional protection against rust and wear. Included mounting hardware simplifies the installation process, making it suitable for professional mechanics and experienced DIYers alike.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with several Chrysler and Dodge models, including the Chrysler Concorde, Intrepid, LHS, and New Yorker. The part number TA5541 ensures correct fitment and function for these vehicles, supporting front steering system maintenance and repair.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eHelps eliminate steering play or looseness\u003c\/li\u003e\n\u003cli\u003eSupports front-end steering stability\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of tie rod ends\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5541 adjusting sleeve, ensure the vehicle is securely lifted and the front wheels are accessible. Use the included mounting hardware to secure the sleeve properly. Verify thread engagement and alignment settings during installation to maintain steering precision. It is recommended to perform a wheel alignment after installation to ensure optimal handling and tire wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts meet industry standards for quality and reliability. The TA5541 adjusting sleeve is manufactured to provide consistent performance as a standard replacement component. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects. Consult product documentation or authorized sources for exact warranty terms.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388813017269,"sku":"BBMX-TA5541","price":19.91,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5541_Fro_17a74858-b36e-48ad-8f15-57ebdff70ffe.jpg?v=1774724201"},{"product_id":"delphi-ta5553-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5553 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5553 steering tie rod end adjusting sleeve is engineered for precise steering alignment on select Ford, Lincoln, and Mercury vehicles. Constructed from durable steel with a fine thread design, this black adjusting sleeve ensures reliable fitment and performance for your steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 108.0 mm (4.25 inches)\u003c\/li\u003e\n\u003cli\u003eColor: Black finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eThread Type: Fine thread with 18.0 mm diameter\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for easy installation\u003c\/li\u003e\n\u003cli\u003eGrade Type: Regular, standard replacement quality\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5553 adjusting sleeve is designed to provide accurate steering tie rod adjustments on compatible vehicles. Its steel construction offers strength and longevity, while the fine thread type with an 18.0 mm diameter allows for precise alignment settings. Measuring 108.0 mm (4.25 inches) in length, this black sleeve includes all necessary mounting hardware to facilitate straightforward installation. This part meets standard replacement grade requirements, making it suitable for routine maintenance or repair of steering components.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Fitment\u003c\/h2\u003e\u003cp\u003eThis Delphi steering tie rod end adjusting sleeve is compatible with a range of Ford, Lincoln, and Mercury models, including the Ford Colony Park, Continental, Cougar, Grand Marquis, LTD, Marquis, Monarch, Montego, Thunderbird, and the Lincoln Versailles. The TA5553 part number ensures you receive the correct component for these specific vehicles, supporting proper steering function and alignment.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Resolution\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive steering play or looseness\u003c\/li\u003e\n\u003cli\u003eRestores proper tie rod end adjustment capability\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5553 adjusting sleeve requires basic steering system knowledge and tools. Ensure the vehicle is securely lifted and the steering components are accessible. Use the included mounting hardware to secure the sleeve, and verify thread engagement matches the fine thread specifications. After installation, perform a professional wheel alignment to confirm proper steering geometry and safe vehicle operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5553 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent quality and reliability. The steel material and fine thread design contribute to long-lasting performance. While specific warranty details may vary, Delphi parts typically come with a limited warranty against defects in material and workmanship, providing confidence in your purchase.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388813377717,"sku":"BBMX-TA5553","price":18.17,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5553_Fro.jpg?v=1774724204"},{"product_id":"delphi-ta5579-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5579 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5579 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on select Chrysler and Dodge vehicles. Designed with durable steel construction and a black finish, this component ensures reliable performance for front steering systems.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength of 2.6 inches for accurate fitment\u003c\/li\u003e\n\u003cli\u003eBlack color coating for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for dependable service\u003c\/li\u003e\n\u003cli\u003eThread diameter options of 0.78 and 19.812 mm for compatibility\u003c\/li\u003e\n\u003cli\u003eDesigned specifically for front position installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5579 adjusting sleeve is a critical hardware component in the steering assembly, providing the necessary adjustment capability for tie rod ends. Its steel material offers the structural integrity required to maintain alignment under driving stresses. The sleeve’s 2.6-inch length and dual thread diameters (0.78 and 19.812 mm) accommodate precise steering geometry adjustments. Finished in black, the sleeve resists corrosion, extending its service life. This part is a standard replacement grade, suitable for maintaining original equipment specifications on compatible vehicles.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with front steering systems on Chrysler and Dodge models including the 300M, Concorde, Intrepid, and LHS. The part number TA5579 ensures correct fitment for these vehicles, supporting proper steering alignment and handling characteristics.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003ePrevents excessive play in tie rod ends\u003c\/li\u003e\n\u003cli\u003eHelps maintain vehicle handling stability\u003c\/li\u003e\n\u003cli\u003eSupports safe and responsive steering control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5579 adjusting sleeve, ensure the vehicle is securely lifted and the front steering components are accessible. Verify thread compatibility with the tie rod ends before assembly. Use appropriate torque specifications to avoid over-tightening, which can damage threads or affect steering performance. It is recommended to perform a wheel alignment after installation to confirm proper steering geometry.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5579 adjusting sleeve to meet standard replacement grade requirements, ensuring consistent quality and durability. The steel construction and corrosion-resistant finish contribute to long-term reliability. While specific warranty details may vary, Delphi parts typically come with a limited warranty covering defects in material and workmanship under normal use.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388822847669,"sku":"BBMX-TA5579","price":29.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5579_Fro.jpg?v=1774724210"},{"product_id":"delphi-ta5654-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5654 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5654 steering tie rod end adjusting sleeve is engineered for reliable performance in select Acura, Honda, Isuzu, and Nissan vehicles. Constructed from durable steel, this standard replacement part ensures precise steering alignment and secure fitment for models like the Nissan Frontier and Honda Passport.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength of 168.0 mm (6.614 inches) for exact fitment\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.551 inches for compatibility with OEM components\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard grade replacement designed for regular use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5654 adjusting sleeve is a critical component in the steering system, providing the necessary adjustment range to maintain proper tie rod alignment. Its steel construction offers resistance to wear and corrosion, supporting long-term vehicle safety and handling. The included mounting hardware simplifies installation, reducing downtime during repairs or replacements. This part is designed to meet the specifications required for Acura, Honda, Isuzu, and Nissan models such as the Isuzu Rodeo, Nissan Xterra, and Honda SLX.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with the following makes and models:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eAcura SLX\u003c\/li\u003e\n\u003cli\u003eHonda Passport\u003c\/li\u003e\n\u003cli\u003eIsuzu Amigo, Rodeo, Trooper\u003c\/li\u003e\n\u003cli\u003eNissan Frontier, Pickup, Xterra\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt is intended for use in steering hardware repairs and adjustments where maintaining precise alignment is essential for vehicle control and tire wear prevention.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by TA5654\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment causing uneven tire wear\u003c\/li\u003e\n\u003cli\u003eLoose or worn tie rod connections affecting handling\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper steering geometry\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage to existing adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eReplacement during suspension or steering system overhauls\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5654 adjusting sleeve requires basic mechanical skills and proper tools. Ensure the vehicle is securely lifted and the steering system is free of tension before removal. Use the included mounting hardware to secure the sleeve, and verify thread engagement matches the specified 0.551-inch diameter. After installation, perform a professional wheel alignment to confirm correct steering geometry.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5654 adjusting sleeve to meet industry standards for material quality and dimensional accuracy. This standard replacement part is backed by Delphi's quality control processes, ensuring consistent performance. Warranty coverage details should be confirmed with the point of purchase or Delphi directly.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388828450997,"sku":"BBMX-TA5654","price":27.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5654_Fro.jpg?v=1774724230"},{"product_id":"delphi-ta5675-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5675 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5675 Steering Tie Rod End Adjusting Sleeve is engineered for reliable steering performance on select Dodge trucks and vans. Constructed from durable steel, this standard replacement part ensures precise alignment and secure fitment for front steering components.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength options: 14.37 inches (365.0 mm) for accurate fit\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eDesigned as a regular grade, standard replacement component\u003c\/li\u003e\n\u003cli\u003eCompatible with front position steering tie rod ends\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve, part number TA5675, is designed specifically for front steering systems on Dodge B1500, B2500, B3500, Ram 1500 Van, Ram 2500 Van, and Ram 3500 Van models. The steel construction provides the necessary rigidity to maintain proper steering geometry under normal driving conditions. The included mounting hardware simplifies the replacement process, reducing installation time. With a length of 14.37 inches (365.0 mm), this sleeve fits precisely within the steering linkage to allow for accurate tie rod end adjustments.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis Delphi TA5675 adjusting sleeve is compatible with the following Dodge vehicles:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDodge B1500\u003c\/li\u003e\n\u003cli\u003eDodge B2500\u003c\/li\u003e\n\u003cli\u003eDodge B3500\u003c\/li\u003e\n\u003cli\u003eDodge Ram 1500 Van\u003c\/li\u003e\n\u003cli\u003eDodge Ram 2500 Van\u003c\/li\u003e\n\u003cli\u003eDodge Ram 3500 Van\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt is intended for use in front steering assemblies where tie rod end adjustment is required to maintain proper wheel alignment and steering response.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Part\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoose or worn tie rod end connections causing steering play\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper wheel alignment\u003c\/li\u003e\n\u003cli\u003eUneven tire wear due to misaligned steering components\u003c\/li\u003e\n\u003cli\u003eSteering instability or wandering on straight roads\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage to existing adjusting sleeves\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure vehicle is securely lifted and supported before beginning installation\u003c\/li\u003e\n\u003cli\u003eRemove old adjusting sleeve and inspect tie rod ends for wear\u003c\/li\u003e\n\u003cli\u003eUse the included mounting hardware to secure the new sleeve firmly\u003c\/li\u003e\n\u003cli\u003eAdjust tie rod ends carefully to achieve correct alignment specifications\u003c\/li\u003e\n\u003cli\u003eAfter installation, perform a professional wheel alignment check\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5675 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent performance and durability. The part undergoes quality control inspections to verify material integrity and dimensional accuracy. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to support long-term reliability in steering applications.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388829335733,"sku":"BBMX-TA5675","price":43.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5675_Fro.jpg?v=1774724234"},{"product_id":"delphi-ta5694-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5694 Steering Tie Rod End Adjusting Sleeve - Left Outer","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5694 steering tie rod end adjusting sleeve is designed for precise steering adjustments on Jeep Wrangler and Wrangler JK models. Crafted from durable steel, this left outer sleeve ensures reliable performance and alignment accuracy for your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 3.444 inches (87.5 mm) for exact fitment\u003c\/li\u003e\n\u003cli\u003eThread diameter of 1.062 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003cli\u003eCompatible with left outer position on Jeep Wrangler and Wrangler JK\u003c\/li\u003e\n\u003cli\u003eMounting hardware not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5694 adjusting sleeve is engineered to meet OEM specifications for steering hardware on Jeep Wrangler and Wrangler JK vehicles. Its steel construction provides the necessary strength to maintain steering alignment under various driving conditions. The sleeve measures 3.444 inches (87.5 mm) in length, with a thread diameter of 1.062 inches, ensuring a precise fit for the left outer tie rod end position. This standard replacement grade part is intended for regular maintenance and repair, offering a reliable solution without the need for additional mounting hardware.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Jeep Wrangler and Wrangler JK models, specifically designed for the left outer position. It is ideal for drivers seeking a direct replacement part to restore proper steering function and alignment.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in the steering linkage\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear caused by misalignment\u003c\/li\u003e\n\u003cli\u003eRestores precise steering response\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5694 requires basic mechanical knowledge and appropriate tools. Since mounting hardware is not included, ensure you have the necessary components before beginning. Proper torque specifications should be followed to avoid over-tightening or loosening during operation. It is recommended to perform a wheel alignment after installation to verify correct steering geometry.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5694 adjusting sleeve to meet industry standards for material quality and dimensional accuracy. This part is a standard replacement grade component, designed to provide dependable service life. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to ensure customer confidence in their steering hardware.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388831367349,"sku":"BBMX-TA5694","price":38.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5694_Fro.jpg?v=1774724240"},{"product_id":"delphi-ta5714-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5714 Steering Tie Rod End Adjusting Sleeve - Front","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5714 Steering Tie Rod End Adjusting Sleeve is designed for front steering applications on Ford F-250 Super Duty and F-350 Super Duty models. Constructed from durable steel with a black finish, this standard replacement part ensures reliable performance and precise steering alignment.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 35.63 mm and 905.0 mm for accurate fitment\u003c\/li\u003e\n\u003cli\u003eBlack color finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for front steering position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5714 adjusting sleeve by Delphi is engineered to meet OEM specifications for steering hardware on Ford Super Duty trucks. Its steel construction provides the necessary strength to withstand the stresses of front steering components. The black finish offers additional protection against rust and wear. This part comes with all required mounting hardware, simplifying the replacement process. Designed specifically for the front position, it supports proper tie rod end adjustment and alignment.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Ford F-250 Super Duty and F-350 Super Duty trucks. It is intended for use in front steering assemblies where precise adjustment of the tie rod end is critical for vehicle handling and safety.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in steering components\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear caused by misalignment\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and control\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5714 adjusting sleeve requires basic mechanical skills and appropriate tools. The included mounting hardware facilitates a secure fit. It is recommended to perform a full steering alignment after installation to ensure optimal vehicle handling. Inspect related steering components for wear during replacement to maintain overall system integrity.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5714 adjusting sleeve to meet industry standards for steering hardware. This standard replacement part undergoes quality checks to ensure durability and fitment accuracy. While specific warranty details may vary, Delphi parts typically come with a limited warranty covering defects in material and workmanship.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388832612533,"sku":"BBMX-TA5714","price":154.36,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5714_Fro.jpg?v=1774724243"},{"product_id":"delphi-ta5739-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5739 Steering Tie Rod End Adjusting Sleeve - Outer","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5739 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on Dodge Ram 2500 and Ram 3500 models. Constructed from durable steel with a black finish, this standard replacement part ensures reliable performance in your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength of 218.5 mm (8.6 inches) for exact fitment\u003c\/li\u003e\n\u003cli\u003eThread diameter of 28.575 mm for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for outer position tie rod ends\u003c\/li\u003e\n\u003cli\u003eCompatible with Dodge Ram 2500 and Ram 3500 models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe TA5739 adjusting sleeve by Delphi is designed specifically for the outer position of the steering tie rod ends on Dodge Ram 2500 and Ram 3500 trucks. Its steel construction provides the necessary strength to withstand the stresses of steering adjustments and road conditions. The black finish offers corrosion resistance, extending the service life of the component. With a length of 218.5 mm and a thread diameter of 28.575 mm, this sleeve fits precisely to maintain proper alignment and steering geometry.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged tie rod end adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and handling\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5739 adjusting sleeve, ensure the threads are clean and free of debris to allow smooth adjustment. Use appropriate tools to avoid damaging the sleeve or tie rod ends. After installation, verify steering alignment and perform a test drive to confirm proper steering function. It is recommended to replace both sides simultaneously for balanced steering performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5739 adjusting sleeve to meet standard replacement grade specifications, ensuring consistent quality and fitment. The steel material and corrosion-resistant finish contribute to long-lasting durability. While specific warranty details may vary, Delphi parts typically come with a limited warranty against manufacturing defects, providing confidence in the product's reliability.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388834578613,"sku":"BBMX-TA5739","price":57.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5739_Fro.jpg?v=1774724248"},{"product_id":"delphi-ta5741-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5741 Steering Tie Rod End Adjusting Sleeve - Lower","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5741 Steering Tie Rod End Adjusting Sleeve is designed for precise steering adjustments on Jeep Grand Cherokee models. Constructed from durable steel, this standard replacement part ensures reliable performance in the lower steering assembly.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 1046.0 mm and 41.18 mm for accurate fitment\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.944 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003cli\u003eCompatible with lower steering positions on Jeep Grand Cherokee\u003c\/li\u003e\n\u003cli\u003eMounting hardware not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5741 adjusting sleeve is engineered to meet OEM specifications for the Jeep Grand Cherokee steering system. Its steel construction provides the necessary strength to withstand steering forces and road conditions. The sleeve measures 1046.0 mm in length with an additional length dimension of 41.18 mm, accommodating the specific geometry of the lower tie rod end. Featuring a thread diameter of 0.944 inches, it ensures a secure and precise fit during installation. This part is classified as a regular grade and standard replacement, making it suitable for routine maintenance and repairs.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Jeep Grand Cherokee models requiring a lower position steering component. It is intended for use in steering hardware, fasteners, and fittings, specifically addressing the need for proper tie rod end adjustment and alignment.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play in the steering linkage\u003c\/li\u003e\n\u003cli\u003eImproves steering response and handling\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5741 requires standard tools for steering system maintenance. Since mounting hardware is not included, ensure you have the appropriate fasteners on hand. Proper torque specifications should be followed to maintain secure connections and avoid damage. It is recommended to perform a wheel alignment after installation to ensure optimal steering performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts are manufactured to meet industry standards for quality and durability. The TA5741 adjusting sleeve is a standard replacement part backed by Delphi's commitment to reliable automotive components. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to provide confidence in product longevity.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388834807989,"sku":"BBMX-TA5741","price":46.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5741_Fro.jpg?v=1774724249"},{"product_id":"delphi-ta5742-steering-drag-link-adjusting-sleeve","title":"Delphi TA5742 Steering Drag Link Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Drag Link Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5742 Steering Drag Link Adjusting Sleeve is a standard replacement part designed specifically for Jeep Grand Cherokee models. Engineered to maintain precise steering alignment, this component ensures reliable performance and durability in your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStandard replacement grade for dependable performance\u003c\/li\u003e\n\u003cli\u003eCompatible with Jeep Grand Cherokee steering systems\u003c\/li\u003e\n\u003cli\u003eDurable construction to withstand regular driving conditions\u003c\/li\u003e\n\u003cli\u003ePart number TA5742 for accurate identification and fitment\u003c\/li\u003e\n\u003cli\u003eDesigned to maintain proper drag link adjustment and steering geometry\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThis steering drag link adjusting sleeve from Delphi is manufactured to meet OEM standards, providing a reliable solution for maintaining the steering linkage on Jeep Grand Cherokee vehicles. The TA5742 part number corresponds to a standard replacement grade item, ensuring it meets the necessary specifications for fit and function. The sleeve plays a critical role in adjusting the length of the drag link, which is essential for proper steering alignment and handling.\u003c\/p\u003e\u003ch2\u003ePurpose and Common Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues caused by worn or damaged drag link components\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and vehicle handling\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear related to steering misalignment\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable vehicle operation on Jeep Grand Cherokee models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5742 steering drag link adjusting sleeve, ensure the vehicle is securely lifted and the steering components are accessible. Proper torque specifications should be followed to avoid over-tightening or under-tightening the sleeve. It is recommended to perform a wheel alignment after installation to confirm correct steering geometry. Use appropriate tools to prevent damage to the sleeve or surrounding parts during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5742 steering drag link adjusting sleeve to meet industry standards for quality and durability. This standard replacement part undergoes rigorous testing to ensure it performs reliably under normal driving conditions. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to provide confidence in the product's longevity and performance.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388834775221,"sku":"BBMX-TA5742","price":42.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5742_Fro.jpg?v=1774724249"},{"product_id":"delphi-ta5750-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5750 Steering Tie Rod End Adjusting Sleeve - Left","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5750 steering tie rod end adjusting sleeve is a standard replacement part designed specifically for the left side of select Ford trucks. Engineered to meet OEM specifications, this component ensures precise steering alignment and reliable performance for your Ford Excursion, F-250 Super Duty, and F-350 Super Duty models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStandard replacement grade for dependable durability\u003c\/li\u003e\n\u003cli\u003eLeft side position-specific design\u003c\/li\u003e\n\u003cli\u003eCompatible with Ford Excursion, F-250 Super Duty, and F-350 Super Duty\u003c\/li\u003e\n\u003cli\u003ePart number TA5750 for accurate identification\u003c\/li\u003e\n\u003cli\u003eManufactured by Delphi, a trusted name in automotive steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5750 adjusting sleeve is crafted to provide a secure connection between the steering tie rod end and the steering linkage. Its standard replacement grade ensures it meets the necessary strength and wear resistance required for heavy-duty applications. This part is designed exclusively for the left side, making it essential to verify fitment before installation. Compatible with Ford Excursion, F-250 Super Duty, and F-350 Super Duty models, the Delphi TA5750 helps maintain proper steering geometry and vehicle handling.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Resolution\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is used to adjust and secure the tie rod ends, which are critical for steering alignment. It addresses several steering and handling issues, including:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eLoose or worn steering linkage connections\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper wheel alignment\u003c\/li\u003e\n\u003cli\u003eUneven tire wear caused by misaligned steering components\u003c\/li\u003e\n\u003cli\u003eSteering play or excessive free movement in the steering system\u003c\/li\u003e\n\u003cli\u003eNoise or vibration originating from the steering linkage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5750 adjusting sleeve, ensure the vehicle is securely lifted and supported. Verify the part number and left side orientation before beginning. Proper torque specifications should be followed to avoid over-tightening or under-tightening, which can affect steering performance. It is recommended to perform a wheel alignment after installation to ensure optimal handling and tire wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5750 adjusting sleeve to meet industry standards for quality and durability. This part undergoes rigorous testing to ensure it performs reliably under demanding conditions typical of Ford Excursion, F-250 Super Duty, and F-350 Super Duty vehicles. While specific warranty details may vary, Delphi typically offers coverage against manufacturing defects to provide confidence in the product's longevity and performance.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388835528885,"sku":"BBMX-TA5750","price":24.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5750_Fro.jpg?v=1774724250"},{"product_id":"delphi-ta5770-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5770 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5770 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering alignment on select GM vehicles. Constructed from durable steel with a fine thread design, this black adjusting sleeve ensures reliable performance and fitment for Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 3.27 inches (83.0 mm)\u003c\/li\u003e\n\u003cli\u003eBlack finish for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for easy installation\u003c\/li\u003e\n\u003cli\u003eFine thread type with 18.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5770 adjusting sleeve is designed to provide accurate steering tie rod end adjustments, critical for maintaining proper wheel alignment and vehicle handling. Its fine thread type and 18.0 mm diameter allow for precise tuning, while the steel construction offers strength and longevity. The black coating helps protect against rust and wear, making it suitable for regular driving conditions. This part is compatible with a range of GM vehicles including Buick Achieva, Cadillac Calais, Chevrolet Cavalier, Oldsmobile Cutlass Calais, and Pontiac Grand Am among others.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with the following makes and models:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBuick Achieva\u003c\/li\u003e\n\u003cli\u003eCadillac Calais\u003c\/li\u003e\n\u003cli\u003eChevrolet Cavalier, Cimarron, Corsica\u003c\/li\u003e\n\u003cli\u003eOldsmobile Cutlass Calais, Firenza\u003c\/li\u003e\n\u003cli\u003ePontiac Grand Am, J2000, J2000 Sunbird, Skyhawk, Skylark, Sunbird, Tempest\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Issues Addressed by TA5770 Adjusting Sleeve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment causing uneven tire wear\u003c\/li\u003e\n\u003cli\u003eLoose or worn tie rod ends affecting steering response\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper toe settings\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage to original adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eReplacement during suspension or steering system repairs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure vehicle is securely lifted and supported before installation\u003c\/li\u003e\n\u003cli\u003eUse included mounting hardware to secure the sleeve properly\u003c\/li\u003e\n\u003cli\u003eVerify thread compatibility with existing tie rod ends (18.0 mm fine thread)\u003c\/li\u003e\n\u003cli\u003eAdjust toe settings after installation to manufacturer specifications\u003c\/li\u003e\n\u003cli\u003eInspect adjacent steering components for wear during replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi TA5770 is manufactured to meet standard replacement grade requirements, ensuring consistent fit and function. The steel material and protective black finish contribute to the part’s durability under normal driving conditions. While specific warranty details vary, Delphi parts typically come with a limited warranty against defects in material and workmanship. Always consult product documentation or supplier for exact warranty terms.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388838084789,"sku":"BBMX-TA5770","price":21.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5770_Fro_b83384c5-5153-42d1-9559-dab48f3f6de1.jpg?v=1774724255"},{"product_id":"delphi-ta5849-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5849 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5849 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on Jeep Wrangler models. Crafted from durable steel, this standard replacement part ensures reliable performance and fitment for your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 25.85 mm and 656.6 mm for accurate fit\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.688 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard grade type suitable for regular steering applications\u003c\/li\u003e\n\u003cli\u003eCompatible specifically with Jeep Wrangler models\u003c\/li\u003e\n\u003cli\u003eMounting hardware not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5849 adjusting sleeve is designed to provide precise alignment adjustments for the steering tie rod ends on Jeep Wrangler vehicles. Made from steel, this component offers the necessary strength and resistance to wear, ensuring consistent steering performance. The sleeve features a thread diameter of 0.688 inches, allowing for a secure and stable connection between the tie rod ends. Available in lengths of 25.85 mm and 656.6 mm, it accommodates the specific requirements of the Jeep Wrangler's steering system. This standard replacement part is intended for routine maintenance and repair, helping maintain proper steering geometry and vehicle handling.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering misalignment caused by worn or damaged tie rod ends\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and vehicle control\u003c\/li\u003e\n\u003cli\u003ePrevents uneven tire wear due to improper alignment\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable handling on Jeep Wrangler models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with your Jeep Wrangler model before installation\u003c\/li\u003e\n\u003cli\u003eUse appropriate tools to avoid damaging the threads during adjustment\u003c\/li\u003e\n\u003cli\u003eVerify steering alignment after installation for optimal performance\u003c\/li\u003e\n\u003cli\u003eMounting hardware is not included; reuse existing hardware or source separately\u003c\/li\u003e\n\u003cli\u003eProfessional installation is recommended for precise alignment and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5849 adjusting sleeve to meet standard replacement part specifications, ensuring reliable fit and function. While mounting hardware is not included, the steel construction and standard grade type provide consistent durability. Delphi products typically come with a limited warranty against manufacturing defects; please consult the product documentation or supplier for specific warranty details related to this part.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388841132213,"sku":"BBMX-TA5849","price":46.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5849_Fro.jpg?v=1774724267"},{"product_id":"delphi-ta5886-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5886 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5886 steering tie rod end adjusting sleeve is engineered for reliable steering system adjustments on select Dodge and Mitsubishi vehicles. Constructed from durable steel, this standard replacement part ensures precise alignment and secure fitment for models like the Dodge Ram 50 and Mitsubishi Montero Sport.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength options: 2.51 inches (64.0 mm) for accurate fit\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.63 inches for compatibility with OEM components\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade type for regular use\u003c\/li\u003e\n\u003cli\u003eMounting hardware not included, designed for direct replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5886 adjusting sleeve is a critical component in the steering hardware assembly, designed to connect and adjust the tie rod ends on compatible vehicles. Its steel construction provides the necessary rigidity to maintain steering alignment under normal driving conditions. With a length of 2.51 inches (64.0 mm) and a thread diameter of 0.63 inches, this sleeve matches factory specifications for a secure and precise fit. The part is classified as a regular grade type and standard replacement item, making it suitable for routine maintenance and repairs on Dodge D50, Mitsubishi Mighty Max, Montero, Montero Sport, Power Ram 50, and Ram 50 models.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis Delphi steering tie rod end adjusting sleeve is compatible with the following makes and models:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDodge D50\u003c\/li\u003e\n\u003cli\u003eDodge Power Ram 50\u003c\/li\u003e\n\u003cli\u003eDodge Ram 50\u003c\/li\u003e\n\u003cli\u003eMitsubishi Mighty Max\u003c\/li\u003e\n\u003cli\u003eMitsubishi Montero\u003c\/li\u003e\n\u003cli\u003eMitsubishi Montero Sport\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eIt is designed to restore proper steering geometry and alignment, ensuring safe and responsive handling for these vehicles.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by TA5886\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteering misalignment causing uneven tire wear\u003c\/li\u003e\n\u003cli\u003eLoose or worn tie rod ends affecting steering precision\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper toe settings during wheel alignment\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage to existing adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eReplacement during suspension or steering system repairs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5886 adjusting sleeve requires basic steering system knowledge and appropriate tools. Since mounting hardware is not included, retain original fasteners or source OEM equivalents. Ensure threads are clean and free of debris before installation. After fitting the sleeve, a professional wheel alignment is recommended to verify correct steering geometry and vehicle handling.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5886 adjusting sleeve to meet industry standards for material quality and dimensional accuracy. This part is a standard replacement grade component designed for dependable performance in steering applications. While specific warranty details are not provided, Delphi parts typically adhere to manufacturer guidelines for quality and reliability.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388841558197,"sku":"BBMX-TA5886","price":31.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5886_Fro.jpg?v=1774724270"},{"product_id":"delphi-ta5887-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5887 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5887 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering adjustments on Jeep Wrangler models. Constructed from durable steel, this standard replacement part ensures reliable performance and fitment for your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 115.0 mm (4.52 inches) for accurate fit\u003c\/li\u003e\n\u003cli\u003eThread Diameter: 0.866 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eGrade Type: Regular, standard replacement quality\u003c\/li\u003e\n\u003cli\u003eMounting Hardware: Not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5887 adjusting sleeve is designed specifically for Jeep Wrangler steering systems, providing a precise connection between the tie rod end and the steering linkage. Made from steel, it offers the necessary strength to withstand the stresses of daily driving and off-road conditions. With a length of 115.0 mm (4.52 inches) and a thread diameter of 0.866 inches, this sleeve ensures proper alignment and adjustment capability. As a regular grade replacement part, it meets OEM specifications for fit and function without including additional mounting hardware.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Solving\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues caused by worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eEliminates excessive play or looseness in the steering linkage\u003c\/li\u003e\n\u003cli\u003eRestores proper steering response and handling on Jeep Wrangler vehicles\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of tie rod ends by maintaining secure connections\u003c\/li\u003e\n\u003cli\u003eFacilitates accurate steering adjustments during suspension repairs or upgrades\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure compatibility with Jeep Wrangler models before installation\u003c\/li\u003e\n\u003cli\u003eUse appropriate tools to avoid damaging threads during installation\u003c\/li\u003e\n\u003cli\u003eCheck steering alignment after installation to confirm proper adjustment\u003c\/li\u003e\n\u003cli\u003eReplace mounting hardware separately as it is not included with this part\u003c\/li\u003e\n\u003cli\u003eConsult vehicle service manual for torque specifications and installation procedures\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5887 adjusting sleeve to meet standard replacement grade requirements, ensuring consistent quality and durability. While mounting hardware is not included, the part is designed to OEM standards for reliable fit and function. Warranty coverage details should be confirmed through the original equipment manufacturer or authorized distributors.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388846899381,"sku":"BBMX-TA5887","price":23.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5887_Fro.jpg?v=1774724270"},{"product_id":"delphi-ta5894-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5894 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5894 Steering Tie Rod End Adjusting Sleeve is designed for precise steering adjustments on Isuzu Pickup models. Crafted from durable steel, this component ensures reliable performance and alignment accuracy for your vehicle's steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from high-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength options: 214.1 mm (8.42 inches) for proper fitment\u003c\/li\u003e\n\u003cli\u003eThread diameter of 0.551 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular use\u003c\/li\u003e\n\u003cli\u003eCompatible specifically with Isuzu Pickup models\u003c\/li\u003e\n\u003cli\u003eMounting hardware not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5894 adjusting sleeve is engineered to meet the exact specifications required for steering tie rod end adjustments on Isuzu Pickup vehicles. With a length of 214.1 mm (8.42 inches) and a thread diameter of 0.551 inches, this steel sleeve provides a secure and stable connection between the tie rod and steering components. Its regular grade type and standard replacement item grade make it suitable for routine maintenance and repair tasks without compromising safety or performance.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Isuzu Pickup models, ensuring a precise fit and proper steering alignment. It is intended for use in steering hardware, fasteners, and fittings, specifically addressing the needs of steering system repairs and adjustments.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003ePrevents steering play and improves handling\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable steering response\u003c\/li\u003e\n\u003cli\u003eMaintains proper tie rod end connection\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5894 requires standard tools for steering hardware adjustments. Since mounting hardware is not included, ensure you have the appropriate fasteners on hand. Proper torque specifications should be followed to avoid over-tightening or loosening during operation. It is recommended to perform a wheel alignment after installation to confirm correct steering geometry.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts are manufactured to meet industry standards for quality and durability. The TA5894 adjusting sleeve is made from steel and designed as a standard replacement part, providing reliable service life. While specific warranty details are not provided, Delphi products typically adhere to OEM quality requirements, supporting consistent performance in steering applications.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388847292597,"sku":"BBMX-TA5894","price":24.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5894_Fro.jpg?v=1774724271"},{"product_id":"delphi-ta5901-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5901 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5901 Steering Tie Rod End Adjusting Sleeve is designed specifically for Kia Sportage models, providing a reliable and precise fit. Manufactured from SAE 1045 material with a phosphate finish, this adjusting sleeve ensures durability and corrosion resistance for steering system maintenance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from SAE 1045 high-quality steel for strength and durability\u003c\/li\u003e\n\u003cli\u003e100.0 mm length suitable for Kia Sportage steering assemblies\u003c\/li\u003e\n\u003cli\u003ePhosphate coating enhances corrosion resistance\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eCoarse thread type with 18.0 mm thread diameter for secure fit\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for regular maintenance and repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5901 adjusting sleeve is engineered to meet the specifications required for Kia Sportage steering tie rod assemblies. Its SAE 1045 steel construction offers a balance of toughness and machinability, while the phosphate finish provides a protective layer against rust and wear. The coarse thread type and 18.0 mm diameter ensure compatibility with the corresponding tie rod ends, facilitating proper alignment and adjustment. This part comes with all necessary mounting hardware, simplifying the replacement process.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with Kia Sportage models, making it a suitable choice for technicians and vehicle owners performing steering system repairs or replacements. The TA5901 part number corresponds directly to the required specifications for these vehicles, ensuring a precise fit and reliable performance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues caused by worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003eReplaces corroded or stripped sleeves to restore secure tie rod connections\u003c\/li\u003e\n\u003cli\u003eAddresses loose steering feel due to improper tie rod end adjustment\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of steering components by maintaining proper tension\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Delphi TA5901 adjusting sleeve on a Kia Sportage, ensure the vehicle is securely lifted and the steering components are accessible. Use the included mounting hardware to secure the sleeve, and verify thread engagement with the coarse 18.0 mm threads. Proper torque specifications should be followed to avoid over-tightening or loosening during operation. After installation, a professional wheel alignment is recommended to maintain optimal steering performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5901 adjusting sleeve to meet industry standards for material quality and dimensional accuracy. This standard replacement grade part undergoes quality control inspections to ensure consistent performance. While specific warranty details may vary, Delphi parts typically come with a limited warranty covering defects in material and workmanship under normal use conditions.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388847653045,"sku":"BBMX-TA5901","price":19.66,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5901_Fro.jpg?v=1774724272"},{"product_id":"delphi-ta5907-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5907 Steering Tie Rod End Adjusting Sleeve","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5907 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering alignment on select Chrysler and Dodge vehicles. Constructed from durable steel, this component ensures reliable performance and fitment for models such as the Chrysler Aspen, Dodge Charger, and Dodge Magnum.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-strength steel for durability\u003c\/li\u003e\n\u003cli\u003eLength: 210.0 mm (8.26 inches) for accurate fit\u003c\/li\u003e\n\u003cli\u003eThread Diameter: 0.563 inches for secure connection\u003c\/li\u003e\n\u003cli\u003eGrade Type: Regular, standard replacement quality\u003c\/li\u003e\n\u003cli\u003eMounting Hardware: Not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5907 adjusting sleeve is designed as a standard replacement part, meeting OEM specifications for steering tie rod end adjustments. Its steel construction provides the necessary strength to maintain proper steering geometry under normal driving conditions. With a length of 210 mm (8.26 inches) and a thread diameter of 0.563 inches, this sleeve fits precisely on compatible tie rod ends, ensuring stable and responsive steering control.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering tie rod end adjusting sleeve is compatible with various Chrysler and Dodge models, including the Chrysler Aspen, Charger, Magnum, Monaco, Newport, and New Yorker. It is intended for use in steering systems requiring a regular grade, standard replacement sleeve to maintain alignment and handling performance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCorrects steering alignment issues\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003cli\u003ePrevents excessive play in steering components\u003c\/li\u003e\n\u003cli\u003eMaintains proper tie rod end positioning\u003c\/li\u003e\n\u003cli\u003eSupports safe and stable vehicle handling\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Delphi TA5907 requires removal of the old adjusting sleeve and careful threading of the new sleeve onto the tie rod ends. Since mounting hardware is not included, ensure all necessary fasteners are available before beginning the installation. Proper torque specifications should be followed to avoid loosening or damage during operation. It is recommended to perform a wheel alignment after installation to verify correct steering geometry.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi manufactures the TA5907 adjusting sleeve to meet industry standards for material and dimensional accuracy. This part is classified as a standard replacement grade, suitable for maintaining original steering system performance. While specific warranty details are not provided, Delphi parts typically adhere to quality control processes to ensure reliability and fitment on compatible Chrysler and Dodge vehicles.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388848144565,"sku":"BBMX-TA5907","price":31.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5907_Fro.jpg?v=1774724273"},{"product_id":"delphi-ta5911-steering-tie-rod-end-adjusting-sleeve","title":"Delphi TA5911 Steering Tie Rod End Adjusting Sleeve - Left or Right","description":"\u003ch2\u003eDelphi Steering Tie Rod End Adjusting Sleeve Overview\u003c\/h2\u003e\u003cp\u003eThe Delphi TA5911 Steering Tie Rod End Adjusting Sleeve is engineered for precise steering alignment on select Dodge, Mitsubishi, and Toyota vehicles. Constructed from durable SAE 1018 material, this black adjusting sleeve ensures reliable performance and fitment for models like the Toyota Corona, Cressida, and Mitsubishi Mighty Max.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eMade from SAE 1018 steel for strength and durability\u003c\/li\u003e\n\u003cli\u003eLength of 174.0 mm for accurate fitment\u003c\/li\u003e\n\u003cli\u003eCoarse thread type with 18.0 mm thread diameter\u003c\/li\u003e\n\u003cli\u003eIncludes mounting hardware for straightforward installation\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade suitable for left and right positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe TA5911 adjusting sleeve is designed as a standard replacement part, meeting regular grade requirements for steering hardware. Its coarse thread and 18.0 mm diameter provide secure engagement with compatible tie rod ends. The black finish offers corrosion resistance, while the included mounting hardware simplifies installation. This part is compatible with left and right steering tie rod ends; users should verify the specific position required for their vehicle model. Compatible vehicles include Dodge Ram 50, Mitsubishi D50 and Mighty Max, and Toyota Corona, Cressida, and Starlet.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDodge Ram 50 steering tie rod end adjustment\u003c\/li\u003e\n\u003cli\u003eMitsubishi D50 and Mighty Max steering hardware replacement\u003c\/li\u003e\n\u003cli\u003eToyota Corona, Cressida, and Starlet tie rod end adjustment\u003c\/li\u003e\n\u003cli\u003eSteering alignment and tie rod end length correction\u003c\/li\u003e\n\u003cli\u003eReplacement for worn or damaged adjusting sleeves\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify left or right position before installation\u003c\/li\u003e\n\u003cli\u003eUse included mounting hardware to ensure secure fit\u003c\/li\u003e\n\u003cli\u003eCheck thread compatibility with existing tie rod ends\u003c\/li\u003e\n\u003cli\u003eApply appropriate torque specifications during assembly\u003c\/li\u003e\n\u003cli\u003eInspect steering components for wear during replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDelphi parts are manufactured to meet industry standards for durability and performance. The TA5911 adjusting sleeve is a standard replacement part designed to maintain steering system integrity. While no specific warranty details are provided, Delphi products typically adhere to OEM quality requirements to ensure reliable service life.\u003c\/p\u003e","brand":"Delphi","offers":[{"title":"Default Title","offer_id":43388848275637,"sku":"BBMX-TA5911","price":24.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DE_TA5911_Fro.jpg?v=1774724274"},{"product_id":"edelmann-39135-power-steering-return-line-end-fitting","title":"Edelmann 39135 Power Steering Return Line End Fitting","description":"\u003ch2\u003eReliable Power Steering Return Line End Fitting for Select Vehicles\u003c\/h2\u003e\u003cp\u003eThe Edelmann Power Steering End Fitting part number 39135 is designed to provide a secure and durable connection for the power steering return line. With a hose length of 5 inches, this fitting is engineered to meet the specifications required by a wide range of vehicles including Buick, Chevrolet, Ford, and Jeep models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eHose length of 5 inches for precise fitment\u003c\/li\u003e\n\u003cli\u003eCompatible with multiple makes including Buick, Cadillac, Chevrolet, Dodge, Ford, GMC, Jeep, Lincoln, Mercury, Oldsmobile, and Pontiac\u003c\/li\u003e\n\u003cli\u003eDesigned specifically for power steering return line applications\u003c\/li\u003e\n\u003cli\u003ePart number 39135 ensures exact replacement and fit\u003c\/li\u003e\n\u003cli\u003eConstructed to meet OEM standards for durability and performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eAbout the Edelmann Power Steering End Fitting Line\u003c\/h2\u003e\u003cp\u003eThe Edelmann Power Steering End Fitting product line focuses on providing high-quality hardware, fasteners, and fittings for steering systems. This line includes components engineered to maintain proper fluid flow and pressure within power steering systems, ensuring reliable steering performance. The 39135 fitting is part of this line, offering a precise 5-inch hose length to accommodate specific vehicle configurations.\u003c\/p\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Edelmann 39135 Power Steering Return Line End Fitting is crafted to replace worn or damaged fittings in the power steering return line. Its 5-inch hose length is designed to fit a variety of models such as the Chevrolet Blazer, Ford F-150, Jeep Cherokee, and Buick LeSabre. This fitting helps maintain the integrity of the power steering system by providing a leak-resistant connection point, which is critical for proper fluid return and steering responsiveness.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement of cracked or leaking power steering return line fittings\u003c\/li\u003e\n\u003cli\u003eRestoring proper fluid flow in power steering systems\u003c\/li\u003e\n\u003cli\u003eResolving steering stiffness caused by fluid leaks\u003c\/li\u003e\n\u003cli\u003ePreventing contamination from entering the power steering system\u003c\/li\u003e\n\u003cli\u003eEnsuring secure hose connections to avoid pressure loss\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify compatibility with your vehicle’s make and model before installation\u003c\/li\u003e\n\u003cli\u003eInspect the power steering hose and surrounding components for wear\u003c\/li\u003e\n\u003cli\u003eUse appropriate tools to avoid damaging the fitting or hose\u003c\/li\u003e\n\u003cli\u003eEnsure all connections are tightened to manufacturer torque specifications\u003c\/li\u003e\n\u003cli\u003eBleed the power steering system after installation to remove air pockets\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eEdelmann parts are manufactured to meet or exceed OEM standards, ensuring reliable performance and durability. The Power Steering End Fitting 39135 undergoes rigorous quality control to maintain consistent fit and function. Warranty coverage details should be confirmed with the product documentation or supplier.\u003c\/p\u003e","brand":"Edelmann","offers":[{"title":"Default Title","offer_id":43413664202933,"sku":"DXMP-39135","price":19.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/EP_39135_Fro_5c5c0cc6-bc76-45c0-ad11-830a2a8e2aa5.jpg?v=1774730923"},{"product_id":"dorman-80983-power-steering-reservoir-cap","title":"Dorman 80983 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap 80983\u003c\/h2\u003e\u003cp\u003eThe Dorman 80983 power steering reservoir cap is designed for reliable sealing and protection of the power steering fluid reservoir. This red plastic screw-on cap is compatible with various Acura and Honda models, including the Accord, Civic, CR-V, and Pilot, ensuring proper fit and function.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable plastic construction for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type for secure fit\u003c\/li\u003e\n\u003cli\u003eRed color finish for easy identification\u003c\/li\u003e\n\u003cli\u003eDiameter of 34.6 mm and height of 36 mm for precise fitment\u003c\/li\u003e\n\u003cli\u003eIncludes one power steering reservoir cap per package\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 80983 power steering reservoir cap is engineered to maintain the integrity of the power steering system by preventing fluid contamination and leaks. Made from sturdy plastic, this cap withstands exposure to heat and chemicals commonly found in automotive environments. Its screw-on design ensures a tight seal on the reservoir, reducing the risk of fluid evaporation or spillage. The red finish aids in quick visual identification during maintenance. With dimensions of 34.6 mm in diameter and 36 mm in height, this cap fits precisely on compatible Acura and Honda power steering reservoirs.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a range of Acura and Honda vehicles, including but not limited to:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eAcura models: CL, Integra, MDX, RL, RDX, RSX, TL, TSX\u003c\/li\u003e\n\u003cli\u003eHonda models: Accord, Accord Crosstour, Civic, Civic del Sol, CR-V, Crosstour, Odyssey, Pilot, Prelude, Ridgeline\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Issues Addressed by This Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks and contamination\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid pressure within the reservoir\u003c\/li\u003e\n\u003cli\u003eProtects against dirt and debris entering the power steering system\u003c\/li\u003e\n\u003cli\u003eHelps avoid premature wear of power steering components\u003c\/li\u003e\n\u003cli\u003eEnsures consistent steering performance and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eAlign the cap threads carefully to avoid cross-threading\u003c\/li\u003e\n\u003cli\u003eTighten the cap securely by hand until snug; avoid over-tightening\u003c\/li\u003e\n\u003cli\u003eCheck for leaks after installation by running the engine and turning the steering wheel\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 80983 power steering reservoir cap undergoes quality inspections to ensure durability and reliability. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship. Refer to Dorman’s official documentation for exact warranty terms.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43415513137333,"sku":"BCZF-80983","price":15.57,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_80983_Fro.jpg?v=1774731442"},{"product_id":"dorman-82540-power-steering-pump-washer","title":"Dorman 82540 Power Steering Pump Washer","description":"\u003ch2\u003ePower Steering Pump Washer for Ford, Lincoln, Mazda, and Mercury Vehicles\u003c\/h2\u003e\u003cp\u003eThe Dorman 82540 power steering pump washer is a specific fit replacement designed for select Ford, Lincoln, Mazda, and Mercury models. Engineered as a standard replacement part, it ensures proper sealing and reliable performance in your vehicle's power steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eStandard replacement grade for dependable durability\u003c\/li\u003e\n\u003cli\u003eSpecific fit for multiple Ford, Lincoln, Mazda, and Mercury models\u003c\/li\u003e\n\u003cli\u003eCompatible with power steering pumps requiring precise sealing washers\u003c\/li\u003e\n\u003cli\u003ePart number 82540 for easy identification and ordering\u003c\/li\u003e\n\u003cli\u003eIncludes one washer per package for straightforward installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 82540 power steering pump washer is manufactured to meet OEM specifications, providing a reliable seal between the power steering pump and its mounting surface. This washer is essential for preventing fluid leaks and maintaining proper hydraulic pressure within the power steering system. Designed specifically for vehicles such as the Ford F-150, Lincoln Continental, Mazda B2300, and Mercury Cougar, this part ensures compatibility and optimal function. Using the correct washer helps avoid premature wear and potential steering issues caused by fluid loss or contamination.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks at the pump mounting point\u003c\/li\u003e\n\u003cli\u003eEliminates noise and vibration caused by improper sealing\u003c\/li\u003e\n\u003cli\u003eMaintains hydraulic pressure for smooth steering operation\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged washers during pump servicing\u003c\/li\u003e\n\u003cli\u003eHelps avoid costly power steering pump failures\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Dorman 82540 washer, ensure the power steering pump mounting surface is clean and free of debris. Replace the washer whenever the pump is removed or serviced to maintain a proper seal. Tighten mounting bolts to manufacturer torque specifications to prevent leaks or damage. This washer is designed for specific vehicle models, so verify compatibility with your Ford, Lincoln, Mazda, or Mercury model before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are engineered to meet or exceed OEM standards, providing reliable performance and fitment. The 82540 power steering pump washer is a standard replacement part backed by Dorman's quality control processes. While specific warranty terms may vary, Dorman typically offers limited warranties covering defects in material and workmanship to ensure customer confidence in their purchase.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417434685621,"sku":"BCZF-82540","price":14.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82540_Fro_04318cb0-2b8e-4544-9096-7bf050c4bbe8.jpg?v=1774731704"},{"product_id":"dorman-82573-power-steering-reservoir-cap","title":"Dorman 82573 Power Steering Reservoir Cap","description":"\u003ch2\u003ePower Steering Reservoir Cap for Buick, Chevrolet, Oldsmobile, Pontiac\u003c\/h2\u003e\u003cp\u003eThe Dorman 82573 power steering reservoir cap is designed to provide a secure seal and maintain proper fluid levels in your vehicle's power steering system. Compatible with select Buick, Chevrolet, Oldsmobile, and Pontiac models, this cap includes a built-in dipstick for easy fluid level checks.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from durable metal, plastic, and rubber materials for reliable sealing\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type ensures a tight, leak-free fit\u003c\/li\u003e\n\u003cli\u003eBlack finish with a diameter of 1.67 inches and height of 2.07 inches\u003c\/li\u003e\n\u003cli\u003eIncludes an integrated dipstick for convenient fluid monitoring\u003c\/li\u003e\n\u003cli\u003ePackaged as a single cap, part number 82573\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDurable Construction and Precise Fit\u003c\/h2\u003e\u003cp\u003eThe Dorman 82573 power steering reservoir cap combines metal, plastic, and rubber components to create a robust and effective seal for your power steering reservoir. The screw-on design allows for easy installation and removal while maintaining a secure fit to prevent fluid leaks. The included dipstick simplifies routine maintenance by allowing quick checks of power steering fluid levels without removing the cap entirely. This cap is finished in black and measures 1.67 inches in diameter and 2.07 inches in height, ensuring compatibility with the specified vehicle models.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with various Buick, Chevrolet, Oldsmobile, and Pontiac models, including the Buick Century and Regal, Chevrolet Lumina and Monte Carlo, Oldsmobile Cutlass Ciera and Cutlass Supreme, and Pontiac Grand Prix. Using the correct reservoir cap helps maintain system pressure and fluid integrity, which is essential for proper steering performance.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid levels to avoid steering system damage\u003c\/li\u003e\n\u003cli\u003eHelps prevent contamination of power steering fluid\u003c\/li\u003e\n\u003cli\u003eEnsures accurate fluid level readings with the integrated dipstick\u003c\/li\u003e\n\u003cli\u003eReduces risk of air entering the power steering system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eScrew the cap on firmly but avoid over-tightening to prevent damage\u003c\/li\u003e\n\u003cli\u003eUse the dipstick to check fluid levels regularly during maintenance\u003c\/li\u003e\n\u003cli\u003eVerify compatibility with your specific vehicle model before installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 82573 power steering reservoir cap undergoes quality checks to ensure durability and reliable performance. Please refer to Dorman's warranty policy for specific coverage details.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417436389557,"sku":"BCZF-82573","price":30.26,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82573_Fro.jpg?v=1774731709"},{"product_id":"dorman-82577-power-steering-reservoir-cap","title":"Dorman 82577 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap 82577\u003c\/h2\u003e\u003cp\u003eThe Dorman 82577 power steering reservoir cap is designed for reliable sealing and easy maintenance on select Chrysler, Dodge, Jeep, and Plymouth vehicles. This screw-on cap features a durable combination of metal, plastic, and rubber materials to ensure a secure fit and long-lasting performance.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed with metal, plastic, and rubber components for durability\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type for secure installation\u003c\/li\u003e\n\u003cli\u003eIncludes a built-in dipstick for fluid level checks\u003c\/li\u003e\n\u003cli\u003eBlack finish with a diameter of 1.65 inches and height of 3.28 inches\u003c\/li\u003e\n\u003cli\u003eCompatible with multiple Chrysler, Dodge, Jeep, and Plymouth models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDurable Materials and Design Features\u003c\/h2\u003e\u003cp\u003eThe Dorman 82577 power steering reservoir cap combines metal, plastic, and rubber materials to provide a robust seal against leaks and contamination. The metal components add strength, while the plastic and rubber ensure a tight, flexible fit. The screw-on design simplifies installation and removal, reducing the risk of cross-threading or damage. The included dipstick allows for quick and accurate fluid level monitoring without removing the cap entirely.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a wide range of vehicles, including Chrysler Acclaim, Dodge Dakota, Jeep Cherokee, Plymouth Sundance, and Ram 1500 models, among others. It is specifically designed to meet the requirements of these vehicles’ power steering systems, ensuring proper fit and function. The part number 82577 corresponds to this exact fitment, making it a reliable replacement for worn or damaged caps on these models.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by the Power Steering Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid pressure within the reservoir\u003c\/li\u003e\n\u003cli\u003eProtects the power steering system from dirt and contaminants\u003c\/li\u003e\n\u003cli\u003eFacilitates easy fluid level checks with the integrated dipstick\u003c\/li\u003e\n\u003cli\u003eHelps avoid steering performance issues related to fluid loss\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Dorman 82577 power steering reservoir cap is straightforward due to its screw-on design. Before installation, ensure the reservoir neck is clean and free of debris. Screw the cap on by hand until snug, avoiding over-tightening which can damage the threads or the cap. Use the dipstick to verify fluid levels after installation and periodically during maintenance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM specifications, providing dependable performance and fit. The 82577 power steering reservoir cap undergoes quality checks to ensure durability and compatibility with specified Chrysler, Dodge, Jeep, and Plymouth models. Warranty coverage details can be obtained from the product packaging or Dorman’s official resources.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417436455093,"sku":"BCZF-82577","price":24.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82577_Fro.jpg?v=1774731709"},{"product_id":"dorman-82581-power-steering-reservoir-cap","title":"Dorman 82581 Power Steering Reservoir Cap","description":"\u003ch2\u003eDurable Power Steering Reservoir Cap for GM Vehicles\u003c\/h2\u003e\u003cp\u003eThe Dorman 82581 power steering reservoir cap is designed to provide a secure seal and reliable performance for a wide range of General Motors vehicles. Featuring a screw-on attachment and a built-in dipstick, this cap ensures proper fluid maintenance and prevents leaks in your power steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from a combination of metal, plastic, and rubber materials for durability and sealing\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type for easy installation and secure fit\u003c\/li\u003e\n\u003cli\u003eIncludes a dipstick for convenient fluid level checks\u003c\/li\u003e\n\u003cli\u003eBlack finish with a diameter of 1.67 inches and height of 3.33 inches\u003c\/li\u003e\n\u003cli\u003eCompatible with multiple Buick, Cadillac, Chevrolet, GMC, Oldsmobile, and Pontiac models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details and Specifications\u003c\/h2\u003e\u003cp\u003eThe Dorman 82581 power steering reservoir cap is engineered with a metal core, plastic body, and rubber sealing components to withstand the demands of power steering systems. Its screw-on design ensures a tight fit to prevent fluid leaks and contamination. The included dipstick allows for quick and accurate fluid level monitoring without removing the cap entirely. Measuring 1.67 inches in diameter and 3.33 inches in height, this cap fits reservoir openings on various GM trucks, SUVs, and cars, including models like the Chevrolet Silverado 1500, GMC Sierra 1500, Cadillac DeVille, Buick LeSabre, and Pontiac Firebird.\u003c\/p\u003e\u003ch2\u003eCompatible GM Makes and Models\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a broad range of General Motors vehicles, including Buick, Cadillac, Chevrolet, GMC, Oldsmobile, and Pontiac. It fits popular models such as the Chevrolet Blazer, Silverado 1500, Camaro, and Suburban series, as well as Cadillac Escalade and DeVille, Buick Century and LeSabre, and Pontiac Grand Prix and Firebird. The Dorman 82581 is suitable for both light trucks and passenger cars from these brands, covering many model years and configurations.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid pressure and system integrity\u003c\/li\u003e\n\u003cli\u003eHelps avoid contamination of power steering fluid\u003c\/li\u003e\n\u003cli\u003eFacilitates easy fluid level checks with the integrated dipstick\u003c\/li\u003e\n\u003cli\u003eReplaces missing or cracked caps to restore system reliability\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Dorman 82581 power steering reservoir cap is straightforward due to its screw-on design. Before installation, ensure the reservoir neck is clean and free of debris. Screw the cap on firmly by hand until it is snug to prevent leaks but avoid over-tightening, which could damage the threads or sealing components. Use the dipstick to verify fluid levels during routine maintenance without removing the cap entirely.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM specifications, providing reliable fit and function. The 82581 power steering reservoir cap undergoes quality checks to ensure durability and proper sealing performance. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship to support customer confidence in their replacement parts.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417436553397,"sku":"BCZF-82581","price":16.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82581_Fro_556446a5-8741-4ea3-ad0a-2b65bd956475.jpg?v=1774731710"},{"product_id":"dorman-82582-power-steering-reservoir-cap","title":"Dorman 82582 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap 82582\u003c\/h2\u003e\u003cp\u003eThe Dorman 82582 power steering reservoir cap is designed for reliable sealing and easy maintenance on select Ford, Lincoln, and Mercury vehicles. This black plastic cap includes a built-in dipstick and features a screw-on attachment for secure fitment.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable black plastic construction\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type for secure installation\u003c\/li\u003e\n\u003cli\u003eIncludes integrated dipstick for fluid level checks\u003c\/li\u003e\n\u003cli\u003eDiameter measures 2.709 inches, height 3.95 inches\u003c\/li\u003e\n\u003cli\u003eCompatible with various Ford, Lincoln, and Mercury models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 82582 power steering reservoir cap is engineered to maintain proper fluid containment and pressure within the power steering system. Made from sturdy plastic, this cap resists corrosion and wear from exposure to power steering fluid and engine heat. The screw-on design ensures a tight seal to prevent leaks and contamination. The integrated dipstick allows for quick and accurate fluid level inspections without removing the cap entirely. Measuring 2.709 inches in diameter and 3.95 inches in height, this cap fits a range of Ford, Lincoln, and Mercury vehicles including the Ford F-150, Explorer, Mustang, and Lincoln Town Car.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with many Ford, Lincoln, and Mercury models, including but not limited to:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFord Bronco, Bronco II, F-100, F-150, F-250, F-350, Excursion, Explorer, Ranger\u003c\/li\u003e\n\u003cli\u003eLincoln Continental, Mark VI, Mark VII, Town Car, Town Car LTD Crown Victoria\u003c\/li\u003e\n\u003cli\u003eMercury Cougar, Capri, Lynx, Marquis, Sable, Zephyr\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eUse this cap to replace worn or damaged reservoir caps on these vehicles to maintain proper power steering system function.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePreventing power steering fluid leaks from the reservoir\u003c\/li\u003e\n\u003cli\u003eMaintaining correct fluid pressure within the power steering system\u003c\/li\u003e\n\u003cli\u003eProtecting fluid from contamination and debris\u003c\/li\u003e\n\u003cli\u003eEnabling easy fluid level checks with the included dipstick\u003c\/li\u003e\n\u003cli\u003eReplacing cracked or missing reservoir caps\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eScrew the cap on firmly but avoid over-tightening to prevent damage\u003c\/li\u003e\n\u003cli\u003eUse the dipstick to check fluid levels regularly for optimal system performance\u003c\/li\u003e\n\u003cli\u003eVerify compatibility with your specific vehicle model and year before installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 82582 power steering reservoir cap undergoes quality checks to ensure durability and reliable performance. Warranty coverage details can be obtained from the product documentation or manufacturer.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417436586165,"sku":"BCZF-82582","price":18.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82582_Fro.jpg?v=1774731710"},{"product_id":"dorman-82589-power-steering-reservoir-cap","title":"Dorman 82589 Power Steering Reservoir Cap","description":"\u003ch2\u003ePower Steering Reservoir Cap for Select GM Vehicles\u003c\/h2\u003e\u003cp\u003eThe Dorman 82589 power steering reservoir cap is designed to provide a secure seal for the power steering fluid reservoir on various Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models. This cap features a screw-on attachment type and includes a dipstick for easy fluid level checks.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable construction combining metal, plastic, and rubber materials\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment ensures a tight, leak-resistant fit\u003c\/li\u003e\n\u003cli\u003eIncludes dipstick for convenient fluid monitoring\u003c\/li\u003e\n\u003cli\u003eBlack finish with a diameter of 1.65 inches and height of 2.058 inches\u003c\/li\u003e\n\u003cli\u003eCompatible with multiple GM vehicles including Camaro, Impala, Malibu, and more\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDurable Materials and Design\u003c\/h2\u003e\u003cp\u003eThe Dorman 82589 power steering reservoir cap is constructed using a combination of metal, plastic, and rubber components to provide durability and reliable sealing performance. The metal and plastic materials offer resistance to wear and corrosion, while the rubber gasket ensures a tight seal to prevent fluid leaks. The screw-on design allows for easy installation and removal without compromising the integrity of the reservoir.\u003c\/p\u003e\u003ch2\u003eCompatible GM Makes and Models\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a wide range of General Motors vehicles, including Buick Achieva, Century, Regal, and Skylark; Cadillac Calais; Chevrolet Camaro, Cavalier, Impala, Lumina, Malibu, Monte Carlo, and Montana; Oldsmobile Cutlass, Cutlass Calais, Cutlass Ciera, Cutlass Supreme, Firenza; and Pontiac Aztek, Firebird, Grand Am, Grand Prix, Sunbird, Sunfire, Rendezvous, Silhouette, and Trans Sport. The Dorman 82589 cap is designed to meet the specifications required for these models, ensuring proper fit and function.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Problem Resolution\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid pressure within the power steering system\u003c\/li\u003e\n\u003cli\u003eHelps avoid contamination of power steering fluid\u003c\/li\u003e\n\u003cli\u003eFacilitates accurate fluid level checks with the included dipstick\u003c\/li\u003e\n\u003cli\u003eReplaces missing or cracked reservoir caps to restore system integrity\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Dorman 82589 power steering reservoir cap is straightforward due to its screw-on design. Before installation, ensure the reservoir neck is clean and free of debris. Screw the cap on firmly by hand until secure, but avoid over-tightening to prevent damage to the threads or gasket. Use the dipstick to verify fluid levels during routine maintenance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 82589 power steering reservoir cap undergoes quality checks to ensure durability and reliable sealing performance. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417436651701,"sku":"BCZF-82589","price":37.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82589_Fro_c8a0fee4-d8b5-49e1-a491-6e7965f518fa.jpg?v=1774731710"},{"product_id":"dorman-82605-power-steering-reservoir-cap","title":"Dorman 82605 Power Steering Reservoir Cap","description":"\u003ch2\u003ePower Steering Reservoir Cap for Select GM Vehicles\u003c\/h2\u003e\u003cp\u003eThe Dorman 82605 power steering reservoir cap is designed to provide a secure seal and maintain proper fluid levels in your vehicle's power steering system. Compatible with a range of Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac models, this cap includes a built-in dipstick for easy fluid level checks.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable black plastic construction\u003c\/li\u003e\n\u003cli\u003eTwist-on attachment type for secure fit\u003c\/li\u003e\n\u003cli\u003eIncludes integrated dipstick for fluid monitoring\u003c\/li\u003e\n\u003cli\u003eMeasures 2 inches in diameter and 2.8 inches in height\u003c\/li\u003e\n\u003cli\u003eCompatible with multiple GM makes and models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDurable Design and Precise Fit\u003c\/h2\u003e\u003cp\u003eManufactured from high-quality plastic, the Dorman 82605 power steering reservoir cap offers reliable performance and resistance to wear. The twist-on design ensures a tight seal to prevent leaks and contamination, while the included dipstick allows for quick and accurate fluid level checks without removing the cap entirely. Its 2-inch diameter and 2.8-inch height dimensions are engineered to match original equipment specifications for a proper fit on compatible vehicles.\u003c\/p\u003e\u003ch2\u003eCompatible GM Makes and Models\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a wide range of General Motors vehicles, including Buick models like Century, LeSabre, and Regal; Cadillac models such as DeVille, Eldorado, and Seville; Chevrolet vehicles including Camaro, Caprice, and Impala; Oldsmobile models like Cutlass and Aurora; and Pontiac models including Firebird, Grand Prix, and Sunfire. The Dorman 82605 is designed to meet the needs of these specific vehicles, ensuring proper fit and function.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks from the reservoir\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid levels with integrated dipstick\u003c\/li\u003e\n\u003cli\u003eProtects the power steering system from dirt and debris\u003c\/li\u003e\n\u003cli\u003eEnsures secure attachment to avoid cap loosening\u003c\/li\u003e\n\u003cli\u003eHelps maintain consistent steering performance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Dorman 82605 power steering reservoir cap is straightforward. Simply twist the cap onto the reservoir opening until it is securely seated. Use the integrated dipstick to check fluid levels regularly, especially during routine maintenance. Ensure the cap is tightened properly to prevent leaks but avoid over-tightening which could damage the threads.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards, providing reliable replacement components for your vehicle. The 82605 power steering reservoir cap undergoes quality inspections to ensure durability and proper fitment. Please refer to Dorman's warranty policy for specific coverage details.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417437896885,"sku":"BCZF-82605","price":34.46,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82605_Fro_8f415f72-db7c-4c4a-a11d-7105029fa25e.jpg?v=1774731713"},{"product_id":"dorman-82746-power-steering-reservoir-cap","title":"Dorman 82746 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap 82746\u003c\/h2\u003e\u003cp\u003eThe Dorman Power Steering Reservoir Cap 82746 is designed for reliable sealing and easy maintenance on select Chrysler and Dodge vehicles. This screw-on cap features a built-in dipstick for convenient fluid level checks, making it a practical replacement part for your power steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable plastic construction in black and gray finish\u003c\/li\u003e\n\u003cli\u003eScrew-on attachment type for secure fitment\u003c\/li\u003e\n\u003cli\u003eIncludes integrated dipstick for fluid monitoring\u003c\/li\u003e\n\u003cli\u003eMeasures 2 inches in diameter and 3.25 inches in height\u003c\/li\u003e\n\u003cli\u003eCompatible with various Chrysler and Dodge models including Ram 1500, Charger, and Durango\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 82746 power steering reservoir cap is engineered from sturdy plastic to withstand typical engine bay conditions. Its screw-on design ensures a tight seal to prevent fluid leaks and contamination. The included dipstick allows for quick and accurate checking of power steering fluid levels without removing the cap entirely. With a diameter of 2 inches and height of 3.25 inches, this cap fits precisely on the power steering reservoirs of multiple Chrysler and Dodge vehicles such as the 300, Aspen, Challenger, Magnum, and Ram series trucks.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a range of Chrysler and Dodge models, making it suitable for owners needing a direct replacement part. Compatible vehicles include:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eChrysler 300 and Aspen\u003c\/li\u003e\n\u003cli\u003eDodge Challenger, Charger, Durango, and Magnum\u003c\/li\u003e\n\u003cli\u003eDodge Ram 1500, Ram 2500, and Ram 3500\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Issues Addressed by This Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePreventing power steering fluid leaks due to worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eMaintaining proper fluid levels with the integrated dipstick\u003c\/li\u003e\n\u003cli\u003eProtecting the power steering system from dirt and debris contamination\u003c\/li\u003e\n\u003cli\u003eEnsuring a secure seal to avoid pressure loss in the reservoir\u003c\/li\u003e\n\u003cli\u003eReplacing missing or cracked reservoir caps on Chrysler and Dodge vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eAlign the cap threads carefully and screw on until snug to avoid cross-threading\u003c\/li\u003e\n\u003cli\u003eUse the dipstick to check fluid levels regularly after installation\u003c\/li\u003e\n\u003cli\u003eDo not overtighten the cap to prevent damage to the plastic threads\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM specifications for fit and function. The 82746 power steering reservoir cap undergoes quality checks to ensure durability and proper sealing performance. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43417446908085,"sku":"BCZF-82746","price":32.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_82746_Fro.jpg?v=1774731732"},{"product_id":"dorman-99977-power-steering-reservoir-cap","title":"Dorman 99977 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap for Hummer H3 and H3T\u003c\/h2\u003e\u003cp\u003eThe Dorman 99977 power steering reservoir cap is designed specifically for Hummer H3 and H3T models. This durable plastic cap features a twist-on attachment and includes a built-in dipstick for easy fluid level checks, ensuring proper maintenance of your vehicle's power steering system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eConstructed from durable black plastic material\u003c\/li\u003e\n\u003cli\u003eTwist-on attachment type for secure fitment\u003c\/li\u003e\n\u003cli\u003eIncludes integrated dipstick for fluid level monitoring\u003c\/li\u003e\n\u003cli\u003eMeasures 2.06 inches in diameter and 2.95 inches in height\u003c\/li\u003e\n\u003cli\u003eCompatible with Hummer H3 and H3T power steering reservoirs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 99977 power steering reservoir cap is engineered to meet the specifications required for Hummer H3 and H3T vehicles. Its black plastic construction offers resistance to corrosion and wear, while the twist-on design ensures a tight seal to prevent fluid leaks. The included dipstick allows for convenient and accurate checking of power steering fluid levels without removing the cap entirely, helping maintain optimal steering performance and preventing potential damage caused by low fluid levels.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid contamination and leakage\u003c\/li\u003e\n\u003cli\u003eHelps maintain proper fluid levels to avoid steering system damage\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged reservoir caps on Hummer H3 and H3T models\u003c\/li\u003e\n\u003cli\u003eEnsures secure sealing to reduce risk of fluid evaporation\u003c\/li\u003e\n\u003cli\u003eFacilitates routine maintenance with integrated dipstick\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eAlign the cap properly and twist until securely tightened to avoid leaks\u003c\/li\u003e\n\u003cli\u003eUse the dipstick to check fluid levels regularly during maintenance\u003c\/li\u003e\n\u003cli\u003eInspect the cap periodically for cracks or wear and replace as needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit and function. The 99977 power steering reservoir cap undergoes quality checks to ensure durability and reliable performance on Hummer H3 and H3T vehicles. Warranty coverage details can be obtained from the product packaging or Dorman's official documentation.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43422760796341,"sku":"BCZF-99977","price":45.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_99977_Fro.jpg?v=1774732193"},{"product_id":"dorman-99978-power-steering-reservoir-cap","title":"Dorman 99978 Power Steering Reservoir Cap","description":"\u003ch2\u003ePower Steering Reservoir Cap for Jeep Grand Cherokee and Wrangler\u003c\/h2\u003e\u003cp\u003eThe Dorman 99978 power steering reservoir cap is designed specifically for Jeep Grand Cherokee and Wrangler models. Made from durable black plastic, this twist-on cap includes a built-in dipstick for easy fluid level checks, ensuring proper maintenance of your vehicle's power steering system.\u003c\/p\u003e\u003ch2\u003eKey Features of Dorman 99978 Power Steering Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-quality black plastic for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eAttachment Type: Twist-on design for secure fitment\u003c\/li\u003e\n\u003cli\u003eDiameter: 2.06 inches, compatible with specified Jeep models\u003c\/li\u003e\n\u003cli\u003eHeight: 3.15 inches for proper sealing and clearance\u003c\/li\u003e\n\u003cli\u003eIncludes integrated dipstick for fluid level monitoring\u003c\/li\u003e\n\u003cli\u003ePackage contains one power steering reservoir cap\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 99978 power steering reservoir cap is engineered to meet the specifications of Jeep Grand Cherokee and Wrangler vehicles. Its black plastic construction offers durability and resistance to heat and chemicals commonly found in automotive fluids. The twist-on attachment type ensures a tight seal to prevent leaks and contamination. The included dipstick allows for quick and accurate checking of power steering fluid levels without removing the cap entirely, helping maintain optimal steering performance.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eHelps maintain proper fluid levels to avoid steering system damage\u003c\/li\u003e\n\u003cli\u003eProtects the reservoir from dirt and debris contamination\u003c\/li\u003e\n\u003cli\u003eReplaces lost or cracked caps to restore system integrity\u003c\/li\u003e\n\u003cli\u003eFacilitates routine maintenance with built-in dipstick\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean before installing the cap\u003c\/li\u003e\n\u003cli\u003eAlign the cap properly and twist until securely tightened\u003c\/li\u003e\n\u003cli\u003eCheck fluid levels using the dipstick after installation\u003c\/li\u003e\n\u003cli\u003eInspect the cap periodically for signs of wear or damage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit and function. The 99978 power steering reservoir cap undergoes quality checks to ensure reliable performance on Jeep Grand Cherokee and Wrangler models. Warranty coverage details can be obtained from the product documentation or Dorman directly.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43422761058485,"sku":"BCZF-99978","price":37.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_99978_Fro.jpg?v=1774732193"},{"product_id":"dorman-99979-power-steering-reservoir-cap","title":"Dorman 99979 Power Steering Reservoir Cap","description":"\u003ch2\u003eOverview of Dorman Power Steering Reservoir Cap 99979\u003c\/h2\u003e\u003cp\u003eThe Dorman Power Steering Reservoir Cap 99979 is designed to provide a secure seal for the power steering fluid reservoir on select Nissan and INFINITI vehicles. This black plastic cap features a twist-on attachment type, ensuring easy installation and reliable performance for models like the Nissan Altima and INFINITI QX56.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDurable black plastic construction\u003c\/li\u003e\n\u003cli\u003eTwist-on attachment for secure fit\u003c\/li\u003e\n\u003cli\u003eDiameter: 2.29 inches for precise sealing\u003c\/li\u003e\n\u003cli\u003eHeight: 1 inch for compact design\u003c\/li\u003e\n\u003cli\u003eIncludes one power steering reservoir cap per package\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 99979 power steering reservoir cap is engineered from sturdy plastic material to withstand the conditions within the engine bay. Its twist-on design allows for straightforward installation and removal without the need for additional tools. Measuring 2.29 inches in diameter and 1 inch in height, this cap fits tightly to prevent fluid leaks and contamination. The black finish complements the engine compartment while maintaining durability against heat and wear.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis power steering reservoir cap is compatible with a range of Nissan and INFINITI models, including the Nissan Altima, Armada, Frontier, Maxima, Pathfinder, Quest, TITAN, TITAN XD, Xterra, and the INFINITI QX56. It is specifically designed to replace the original reservoir cap on these vehicles, ensuring proper fit and function.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed by This Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks from the reservoir\u003c\/li\u003e\n\u003cli\u003eProtects fluid from dirt and debris contamination\u003c\/li\u003e\n\u003cli\u003eMaintains proper pressure within the power steering system\u003c\/li\u003e\n\u003cli\u003eHelps avoid premature wear of power steering components\u003c\/li\u003e\n\u003cli\u003eEnsures consistent steering performance and safety\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Dorman 99979 power steering reservoir cap is straightforward due to its twist-on design. Before installation, ensure the reservoir neck is clean and free of debris. Align the cap properly and twist clockwise until securely tightened. Avoid over-tightening to prevent damage to the cap or reservoir threads. No dipstick is included with this cap, so fluid level checks should be performed separately.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 99979 power steering reservoir cap undergoes quality inspections to ensure durability and reliability. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship. Refer to Dorman’s official documentation for exact warranty terms.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43422761091253,"sku":"BCZF-99979","price":34.76,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_99979_Fro.jpg?v=1774732194"},{"product_id":"dorman-99979cd-power-steering-reservoir-cap","title":"Dorman 99979CD Power Steering Reservoir Cap","description":"\u003ch2\u003ePower Steering Reservoir Cap for Nissan and INFINITI Vehicles\u003c\/h2\u003e\u003cp\u003eThe Dorman 99979CD power steering reservoir cap is designed to provide a secure seal for the power steering fluid reservoir on select Nissan and INFINITI models. Manufactured from durable black plastic with a screw-on attachment, this cap ensures proper fluid containment and helps maintain system performance.\u003c\/p\u003e\u003ch2\u003eKey Features of the Dorman 99979CD Power Steering Reservoir Cap\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMaterial: High-quality black plastic for corrosion resistance\u003c\/li\u003e\n\u003cli\u003eAttachment Type: Screw-on design for a tight, reliable fit\u003c\/li\u003e\n\u003cli\u003eDiameter: 2.29 inches, compatible with specified reservoir openings\u003c\/li\u003e\n\u003cli\u003eHeight: 1 inch for proper sealing and clearance\u003c\/li\u003e\n\u003cli\u003eDipstick: Not included, designed solely as a reservoir cap\u003c\/li\u003e\n\u003cli\u003ePackage Contents: Includes one power steering reservoir cap\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Dorman 99979CD power steering reservoir cap is engineered to meet the specifications required for a range of Nissan and INFINITI vehicles, including the Altima, Armada, Frontier, Maxima, Pathfinder, Pathfinder Armada, Quest, QX56, Sentra, TITAN, TITAN XD, and Xterra. Its screw-on attachment type ensures a secure fit that prevents leaks and contamination of the power steering fluid. The black plastic construction offers durability and resistance to the heat and chemicals typically found in engine compartments. With a diameter of 2.29 inches and a height of 1 inch, this cap fits precisely on the designated reservoirs, maintaining system integrity.\u003c\/p\u003e\u003ch2\u003eCommon Applications and Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePrevents power steering fluid leaks caused by worn or damaged caps\u003c\/li\u003e\n\u003cli\u003eProtects the power steering system from dirt and debris contamination\u003c\/li\u003e\n\u003cli\u003eMaintains proper fluid pressure within the reservoir\u003c\/li\u003e\n\u003cli\u003eReplaces lost or missing reservoir caps on compatible Nissan and INFINITI models\u003c\/li\u003e\n\u003cli\u003eHelps avoid steering performance issues related to fluid loss\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure the reservoir neck is clean and free of debris before installation\u003c\/li\u003e\n\u003cli\u003eAlign the cap properly and screw on until snug; avoid over-tightening\u003c\/li\u003e\n\u003cli\u003eCheck for leaks after installation by running the engine and inspecting the reservoir\u003c\/li\u003e\n\u003cli\u003eConsult the vehicle’s service manual for specific torque specifications if available\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty Information\u003c\/h2\u003e\u003cp\u003eDorman parts are manufactured to meet or exceed OEM standards for fit, form, and function. The 99979CD power steering reservoir cap undergoes quality control inspections to ensure durability and reliability. While specific warranty details may vary, Dorman typically offers limited warranties covering defects in material and workmanship. Refer to Dorman’s official warranty policy for complete information.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43422761156789,"sku":"BCZF-99979CD","price":33.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MM_99979CD_Fro.jpg?v=1774732194"},{"product_id":"moog-8430b-steering-king-pin-set","title":"Moog 8430B Steering King Pin Set","description":"\u003ch2\u003eMoog Steering King Pin Set Overview\u003c\/h2\u003e\u003cp\u003eThe Moog 8430B Steering King Pin Set is designed specifically for Ford F-100 and F-250 models, providing reliable steering hardware replacement. This set includes all necessary components to restore proper steering function and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIncludes metal bushings and washers for secure fitment\u003c\/li\u003e\n\u003cli\u003eKing pin length of 5.860 inches and diameter of 0.859 inches\u003c\/li\u003e\n\u003cli\u003eFour metal bushings included for enhanced wear resistance\u003c\/li\u003e\n\u003cli\u003eBearings and washers included for complete assembly\u003c\/li\u003e\n\u003cli\u003eKeyway length of 2.500 inches for precise alignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Moog 8430B Steering King Pin Set is engineered to meet the specifications required for Ford F-100 and F-250 trucks. Featuring metal bushings, this set ensures durability and long service life under demanding driving conditions. The king pin measures 5.860 inches in length and 0.859 inches in diameter, matching OEM dimensions for proper fit and function. Included bearings and washers facilitate smooth steering operation and reduce wear. The keyway length of 2.500 inches allows for accurate positioning within the steering knuckle assembly.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Solving\u003c\/h2\u003e\u003cp\u003eThis steering king pin set is used to replace worn or damaged king pins and associated hardware in Ford F-100 and F-250 trucks. It addresses common steering issues such as:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExcessive play or looseness in the steering knuckle\u003c\/li\u003e\n\u003cli\u003eUneven tire wear caused by misaligned steering components\u003c\/li\u003e\n\u003cli\u003eSteering vibration or noise during operation\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper wheel alignment\u003c\/li\u003e\n\u003cli\u003ePremature wear of steering linkage components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInstallation of the Moog 8430B Steering King Pin Set requires proper tools and mechanical knowledge. Ensure all old components are fully removed and the steering knuckle is clean before assembly. Use appropriate lubrication on bushings and bearings to facilitate smooth installation and operation. Verify king pin alignment using the keyway length specification to avoid steering issues. Torque all fasteners to manufacturer specifications for safety and performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eMoog parts are manufactured to meet or exceed OEM standards, ensuring reliable performance and durability. The 8430B Steering King Pin Set undergoes rigorous quality control to maintain consistent fit and function. While specific warranty details are not provided here, Moog typically offers limited warranties covering defects in materials and workmanship.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422772265141,"sku":"BCCH-8430B","price":153.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_8430B_Top.jpg?v=1774732241"},{"product_id":"moog-8455b-steering-king-pin-set","title":"Moog 8455B Steering King Pin Set","description":"\u003ch2\u003eOverview of Moog 8455B Steering King Pin Set\u003c\/h2\u003e\u003cp\u003eThe Moog 8455B Steering King Pin Set is designed specifically for Ford F-100 and F-250 models, providing reliable steering hardware replacement. This set includes all necessary components to restore proper steering function and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIncludes metal bushings and washers for secure fitment\u003c\/li\u003e\n\u003cli\u003eKing pin length of 6.540 inches and diameter of 0.859 inches\u003c\/li\u003e\n\u003cli\u003eComes with four metal bushings and bearings for smooth operation\u003c\/li\u003e\n\u003cli\u003eKeyway length measures 2.840 inches for precise alignment\u003c\/li\u003e\n\u003cli\u003eCompatible with Ford F-100 and F-250 trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Moog 8455B Steering King Pin Set features metal bushings that enhance durability and reduce wear in the steering knuckle assembly. The included bearings and washers ensure smooth rotation and proper clearance, maintaining steering precision. With a king pin length of 6.540 inches and a diameter of 0.859 inches, this set matches factory specifications for Ford F-100 and F-250 models. The keyway length of 2.840 inches allows for accurate positioning and secure installation. This comprehensive set is engineered to meet the demands of heavy-duty truck steering systems.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Resolution\u003c\/h2\u003e\u003cp\u003eThis steering king pin set is used to replace worn or damaged king pins and associated hardware in Ford F-100 and F-250 trucks. It addresses common steering issues such as:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExcessive play or looseness in the steering knuckle\u003c\/li\u003e\n\u003cli\u003eUneven tire wear caused by misalignment\u003c\/li\u003e\n\u003cli\u003eSteering vibration or noise during operation\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining proper steering control\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear of original king pin bushings and bearings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEnsure all old components are fully removed before installation\u003c\/li\u003e\n\u003cli\u003eClean the steering knuckle bore to remove debris and corrosion\u003c\/li\u003e\n\u003cli\u003eUse proper lubrication on bushings and bearings during assembly\u003c\/li\u003e\n\u003cli\u003eVerify king pin alignment with the keyway for secure fit\u003c\/li\u003e\n\u003cli\u003eTorque all fasteners to manufacturer specifications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eMoog parts are manufactured to meet or exceed OEM standards, ensuring reliable performance and durability. The 8455B Steering King Pin Set undergoes rigorous quality control to maintain consistent fit and function. While specific warranty details may vary, Moog typically offers coverage against defects in materials and workmanship. Consult product documentation for exact warranty terms.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422772363445,"sku":"BCCH-8455B","price":92.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_8455B_Top.jpg?v=1774732242"},{"product_id":"moog-8524b-steering-king-pin-set","title":"Moog 8524B Steering King Pin Set","description":"\u003ch2\u003eMoog 8524B Steering King Pin Set Overview\u003c\/h2\u003e\u003cp\u003eThe Moog 8524B Steering King Pin Set is designed specifically for Ford F-100 and F-250 models, providing reliable steering hardware replacement. This set includes all necessary components to restore proper steering function and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIncludes metal bushings and washers for secure fitment\u003c\/li\u003e\n\u003cli\u003eKing pin length of 6.812 inches and diameter of 1.109 inches\u003c\/li\u003e\n\u003cli\u003eComes with four metal bushings and a bearing for smooth operation\u003c\/li\u003e\n\u003cli\u003eKeyway length measures 1.984 inches for precise alignment\u003c\/li\u003e\n\u003cli\u003eCompatible with Ford F-100 and F-250 trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Features and Specifications\u003c\/h2\u003e\u003cp\u003eThe Moog 8524B steering king pin set features metal bushings that enhance durability and reduce wear compared to rubber or composite alternatives. The set includes four bushings and washers, ensuring a complete hardware replacement for the steering knuckle assembly. The king pin itself measures 6.812 inches in length and 1.109 inches in diameter, matching OEM specifications for a proper fit. Additionally, the included bearing supports smooth rotational movement, reducing steering play and improving vehicle control. The keyway length of 1.984 inches ensures accurate positioning within the steering components.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles and Applications\u003c\/h2\u003e\u003cp\u003eThis steering king pin set is compatible with Ford F-100 and F-250 models, making it suitable for owners seeking to maintain or restore the steering system on these trucks. The part number 8524B corresponds directly to these applications, ensuring correct fitment and function.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRestores steering stability and reduces play\u003c\/li\u003e\n\u003cli\u003eReplaces worn or damaged king pins and bushings\u003c\/li\u003e\n\u003cli\u003eAddresses steering looseness and uneven tire wear\u003c\/li\u003e\n\u003cli\u003eImproves steering response and safety\u003c\/li\u003e\n\u003cli\u003ePrevents premature wear of steering components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Moog 8524B steering king pin set, ensure all old components are fully removed and the steering knuckle is clean. Proper lubrication of the metal bushings and bearing is recommended to facilitate smooth operation. Verify the king pin length and diameter match OEM specifications before installation. Use appropriate tools to press the bushings and king pin into place without causing damage. After installation, check steering alignment and adjust as necessary.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eMoog parts are engineered to meet or exceed OEM standards, providing reliable performance for steering system repairs. The 8524B steering king pin set undergoes rigorous quality control to ensure durability and fitment accuracy. While specific warranty details may vary, Moog typically offers a limited warranty covering defects in materials and workmanship.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422772592821,"sku":"BCCH-8524B","price":109.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_8524B_Ang.jpg?v=1774732242"},{"product_id":"moog-8524n-steering-king-pin-set","title":"Moog 8524N Steering King Pin Set","description":"\u003ch2\u003eOverview of Moog 8524N Steering King Pin Set\u003c\/h2\u003e\u003cp\u003eThe Moog 8524N Steering King Pin Set is designed specifically for Ford F-100 and F-250 models, providing reliable steering hardware replacement. This set includes all necessary components to restore proper steering function and durability.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eIncludes nylon bushings for enhanced wear resistance\u003c\/li\u003e\n\u003cli\u003eComes with washers and bearings for complete installation\u003c\/li\u003e\n\u003cli\u003eKing pin length of 6.812 inches and diameter of 1.109 inches\u003c\/li\u003e\n\u003cli\u003eFour nylon bushings included to ensure smooth operation\u003c\/li\u003e\n\u003cli\u003eKeyway length measures 1.984 inches for precise fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThe Moog 8524N Steering King Pin Set features a complete assembly with bushings, washers, and bearings included to facilitate a straightforward replacement process. The nylon bushings provide improved durability and reduced friction compared to traditional materials, contributing to longer service life. With a king pin length of 6.812 inches and a diameter of 1.109 inches, this set is engineered to meet the exact specifications required for Ford F-100 and F-250 trucks. The included keyway length of 1.984 inches ensures proper alignment and secure fitment within the steering knuckle assembly.\u003c\/p\u003e\u003ch2\u003eApplications and Problem Resolution\u003c\/h2\u003e\u003cp\u003eThis steering king pin set is compatible with Ford F-100 and F-250 models and is intended for use in steering system repairs and maintenance. It addresses common issues such as:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eExcessive steering play or looseness\u003c\/li\u003e\n\u003cli\u003eUneven tire wear due to misalignment\u003c\/li\u003e\n\u003cli\u003eSteering knuckle wobble or instability\u003c\/li\u003e\n\u003cli\u003eNoise or roughness in steering movement\u003c\/li\u003e\n\u003cli\u003eWear or damage to original king pin components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eWhen installing the Moog 8524N Steering King Pin Set, ensure all old components are fully removed and the steering knuckle is clean. Proper lubrication of the nylon bushings and bearings is recommended to reduce initial wear. Verify the king pin length and diameter match the vehicle specifications before installation. Tighten all fasteners to manufacturer torque specifications to maintain steering integrity.\u003c\/p\u003e\u003ch2\u003eQuality Assurance and Warranty\u003c\/h2\u003e\u003cp\u003eMoog parts are manufactured to meet or exceed OEM standards, ensuring reliable performance and durability. The 8524N Steering King Pin Set undergoes rigorous quality control to maintain consistent fit and function. While specific warranty details may vary, Moog typically offers a limited warranty against defects in materials and workmanship.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422772723893,"sku":"BCCH-8524N","price":101.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_8524N_Ang_f184574d-a731-4b8b-ab54-167987d32442.jpg?v=1774732243"}],"url":"https:\/\/www.partcatalog.com\/collections\/hardware-fasteners-and-fittings-15.oembed?page=7","provider":"PartCatalog","version":"1.0","type":"link"}