{"title":"Transmission \u003e Hoses and Pipes","description":"\u003cp\u003eClutch hydraulic hoses and pipes carry pressurized fluid between the clutch master cylinder and slave cylinder, translating pedal input into clutch engagement. Unlike rigid steel lines, the flexible hose section absorbs drivetrain movement — making it the first point of failure. Rubber hoses degrade from heat cycling and fluid contamination, typically lasting 60,000–100,000 miles, though vehicles in high-heat or high-humidity environments fail earlier. Internal delamination is a common failure mode: the hose looks fine outside but restricts fluid flow internally, causing a clutch that won't fully disengage. When buying, verify the exact routing length and end fitting types (banjo vs. threaded) for your specific make and model — a 2mm difference in fitting diameter will cause a no-fit. OEM-spec rubber or PTFE-lined aftermarket hoses are both reliable; braided stainless upgrades make sense for performance applications or repeated early failures.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClutch pedal sinks to the floor or feels soft and spongy.\u003c\/strong\u003e A deteriorating hose can internally collapse or develop a slow leak, reducing hydraulic pressure and preventing full clutch disengagement.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVisible fluid weeping or wet residue along the hose.\u003c\/strong\u003e Any external seepage — even minor dampness near the fittings or along the hose body — indicates seal breakdown and warrants immediate replacement before total hydraulic failure.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClutch engages and disengages inconsistently or at an unpredictable pedal height.\u003c\/strong\u003e Intermittent internal blockage from a delaminating hose liner causes erratic pressure delivery, making clutch engagement feel notchy or delayed.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eClutch fluid reservoir is losing fluid with no obvious external leak.\u003c\/strong\u003e Small pinhole weeps in the hose can drip onto hot exhaust components and evaporate before pooling — inspect the hose directly before assuming a master or slave cylinder failure.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eDifficulty shifting into gear at a stop, even with the pedal fully depressed.\u003c\/strong\u003e Insufficient hydraulic travel caused by a restricted or leaking hose prevents the clutch from fully releasing, causing grinding when trying to engage first or reverse.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHow often should a clutch hydraulic hose be replaced?\u003c\/strong\u003e\n  There's no fixed service interval from most manufacturers, but 60,000–100,000 miles is a reasonable inspection threshold. Replace immediately if you see cracking, swelling, or fluid weeping. Many shops recommend replacing the hose any time the clutch master or slave cylinder is replaced, since labor overlap makes it inexpensive insurance.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eIs an OEM clutch hydraulic hose worth it over aftermarket?\u003c\/strong\u003e\n  OEM hoses guarantee exact routing length, correct end fittings, and pressure ratings specific to your vehicle. Quality aftermarket options — particularly PTFE-lined or braided stainless hoses — meet or exceed OEM specs at lower cost. Avoid unbranded hoses with vague pressure ratings; for a hydraulic component, material quality directly affects safety and reliability.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eHow difficult is a clutch hydraulic hose replacement, and what else should I replace at the same time?\u003c\/strong\u003e\n  Most clutch hydraulic hose replacements are DIY-accessible in 1–2 hours with basic hand tools and a line wrench set. Parts typically run $15–$80 depending on vehicle. If the hose has failed, replace the clutch fluid and inspect the master and slave cylinders for leaks — both are inexpensive to address with the hydraulic system already open.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"professional-parts-sweden-41341137-clutch-hydraulic-hose","title":"Professional Parts Sweden 41341137 Clutch Hydraulic Hose","description":"\u003ch2\u003eClutch Hydraulic Hose for Hydraulic Linkage Service\u003c\/h2\u003e\u003cp\u003eThis Professional Parts Sweden clutch hydraulic hose routes fluid from the clutch master cylinder to the slave cylinder. It is a direct-fit hydraulic line for restoring clutch pedal response and maintaining consistent hydraulic pressure in the system. Part number 41341137 is built for service work where the original hose has aged, cracked, or begun to leak.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic hose for the line from master cylinder to slave cylinder\u003c\/li\u003e\n\u003cli\u003eProfessional Parts Sweden replacement part number 41341137\u003c\/li\u003e\n\u003cli\u003eSupports hydraulic clutch operation in manual transmission systems\u003c\/li\u003e\n\u003cli\u003eCross-references 5331137 and 8935124 for the same application\u003c\/li\u003e\n\u003cli\u003eRelevant for Volvo S60, Volvo V70, and Volvo XC70 clutch hydraulic service searches\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eSpecification: Från Kopplings till Slav-cylinder, meaning the hose runs from the clutch to the slave cylinder. That makes this part a key hydraulic connection in the clutch release circuit. When the original hose deteriorates, fluid transfer can become inconsistent and clutch engagement can change. This hose is intended for vehicles using the matching hydraulic layout, including Volvo S60, Volvo V70, and Volvo XC70 applications where part number 41341137 is specified.\u003c\/p\u003e\u003cp\u003eThis part cross-references 5331137 and 8935124 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch fluid leakage at the hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel\u003c\/li\u003e\n\u003cli\u003eDelayed clutch disengagement during shifting\u003c\/li\u003e\n\u003cli\u003eVisible cracking, swelling, or wear in the hydraulic line\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure between the master cylinder and slave cylinder\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the hose routing matches the original line from the clutch master cylinder to the slave cylinder before installation. Inspect adjoining hydraulic components, fittings, and seals for wear or contamination before reassembly. After installation, bleed the clutch hydraulic system according to the vehicle service procedure to remove air from the line.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eProfessional Parts Sweden replacement components are selected for service applications where correct fit and hydraulic function matter. Verify part number 41341137 against the original hose and vehicle specifications before ordering.\u003c\/p\u003e","brand":"Professional Parts Sweden","offers":[{"title":"Default Title","offer_id":43589126488245,"sku":"FNJW-41341137","price":38.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/PS_41341137_Fro.jpg?v=1774972338"},{"product_id":"professional-parts-sweden-41344909-clutch-hydraulic-hose","title":"Professional Parts Sweden 41344909 Clutch Hydraulic Hose","description":"\u003ch2\u003eClutch Hydraulic Hose for Saab 9-5\u003c\/h2\u003e\u003cp\u003eProfessional Parts Sweden 41344909 is a clutch hydraulic hose for left-hand drive vehicles. It is listed for Saab 9-5 applications across multiple model years, making it a direct-fit replacement for drivers servicing the clutch hydraulic line on compatible Saab 9-5 vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic hose for left-hand drive vehicles\u003c\/li\u003e\n\u003cli\u003eFits 2000 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2001 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2003 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2006 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2008 Saab 9-5, N\/A\u003c\/li\u003e\n\u003cli\u003ePart number 41344909 for catalog matching and service lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis clutch hydraulic hose routes hydraulic pressure through the clutch system on Saab 9-5 models with left-hand drive configuration. Use it when replacing a worn, leaking, or damaged hose on a Saab 9-5, especially when the original line shows cracking, seepage, or loss of clutch pedal pressure. This part cross-references 5254909 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Reasons\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch pedal feels soft or inconsistent\u003c\/li\u003e\n\u003cli\u003eVisible hydraulic fluid leakage at the hose\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or aged clutch line material\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eService replacement for a Saab 9-5 clutch hydraulic hose\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm left-hand drive configuration before ordering. Match the existing routing and connection points on the Saab 9-5, and inspect the surrounding hydraulic components for wear or contamination during replacement. After installation, bleed the clutch hydraulic system according to the vehicle service procedure and verify firm pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eProfessional Parts Sweden 41344909 is cataloged as a transmission hose and pipe component for the specified Saab 9-5 fitments. Verify part number 41344909 against the vehicle application before installation to ensure correct selection.\u003c\/p\u003e","brand":"Professional Parts Sweden","offers":[{"title":"Default Title","offer_id":43589130715317,"sku":"FNJW-41344909","price":37.17,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/PS_41344909_Fro.jpg?v=1774972340"},{"product_id":"centric-150-10304-clutch-hydraulic-hose","title":"Centric 150.10304 Clutch Hydraulic Hose - Rear or Rear Lower","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers a direct-fit clutch hydraulic hose built for consistent hydraulic transfer and dependable pedal response. Part number 150.10304 is a DOT approved replacement with metal female fittings, EPDM rubber outer sleeve construction, and bubble flare ends for a secure connection.\u003c\/p\u003e\u003cp\u003eCompatible With select vehicle applications that use M10-1.00 female bubble flare connections, this Centric clutch hydraulic hose is built for service replacement work where the original hose has aged, cracked, or begun to leak. The Centric Premium Brake Hydraulic Hoses line focuses on hydraulic components for brake and clutch systems, including hoses, master cylinders, wheel cylinders, repair kits, and remanufactured boosters.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch system service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for durable routing\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eBubble flare connections at both ends\u003c\/li\u003e\n\u003cli\u003eEnd threads: M10-1.00 on both sides\u003c\/li\u003e\n\u003cli\u003eOverall length: 235.00 mm\u003c\/li\u003e\n\u003cli\u003eBlack finish for OE-style appearance\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.10304\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric 150.10304 is a clutch hydraulic hose designed around common hydraulic connection standards used in manual transmission clutch circuits. The hose uses EPDM rubber for the outer sleeve, with female metal fittings and bubble flare ends to support a secure hydraulic seal. It does not include mounting hardware, brackets, grommets, seals, shields, or a Teflon liner. This part cross-references Four Seasons 36974 and Raybestos Brakes BH36974 for the same application.\u003c\/p\u003e\u003cp\u003eFor shoppers searching for a clutch hydraulic hose for Honda Civic or similar manual-transmission service applications, this Centric hose provides a straightforward replacement option when the original line is worn, leaking, or damaged. The part number 150.10304 is also useful when matching an existing hose by thread size, flare type, and overall length.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Addresses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch pedal feels soft or inconsistent due to hydraulic line wear\u003c\/li\u003e\n\u003cli\u003eVisible fluid seepage at the hose or fitting ends\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch circuit\u003c\/li\u003e\n\u003cli\u003eDifficulty matching an OE-style replacement hose by fitting type and thread size\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify end 1 and end 2 thread size, flare type, and hose length before installation. Inspect the mating hydraulic components for corrosion or damaged sealing surfaces, and replace worn clips or retainers as needed since this hose includes clip provisions but no mounting hardware. Bleed the hydraulic system after installation to remove air and restore proper clutch operation. Confirm vehicle-specific routing and clearance before final tightening.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program covers a broad range of hydraulic service parts, including hoses and related brake and clutch components. Part number 150.10304 is DOT approved and built to meet the connection and material requirements listed for this application.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43643268858037,"sku":"BKNJ-150.10304","price":19.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15010304_Fro.jpg?v=1774988622"},{"product_id":"centric-150-34001-clutch-hydraulic-hose","title":"Centric 150.34001 Clutch Hydraulic Hose - Front","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line brings OE-style hydraulic replacement coverage to clutch and brake applications, including this Centric clutch hydraulic hose, part number 150.34001. Built with a black EPDM rubber outer sleeve and metal female fittings, it is DOT approved and uses bubble flare ends with M10-1.00 threads for a direct hydraulic connection.\u003c\/p\u003e\u003cp\u003eCompatible With select BMW, Volvo, and Audi TT Quattro applications, this hose is listed for front-position fitment where specified. The Centric 150.34001 is a practical replacement for worn, cracked, or leaking hydraulic hose assemblies on vehicles such as the BMW 320i, Volvo 240, and Audi TT Quattro.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch and brake system service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for durable fluid-line protection\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eBubble flare ends with M10-1.00 thread size\u003c\/li\u003e\n\u003cli\u003eGasket or seal included\u003c\/li\u003e\n\u003cli\u003eOverall length: 317 mm (12.480 in.)\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line coverage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ hydraulic program, which covers brake and hydraulic service components across a wide range of import vehicles. This hose is engineered as a replacement hydraulic line for applications calling for a black EPDM rubber hose with female-to-female metal ends, bubble flare connections, and DOT approval. The Centric 150.34001 is listed for front-position use on several BMW 3 Series and 5 Series models, Volvo 240 variants, and Audi TT Quattro chassis-specific applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H113300 and Raybestos Brakes BH38000 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid seepage at the hose ends\u003c\/li\u003e\n\u003cli\u003eCracked or aged rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch hydraulic pedal feel\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the line\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the fitting connection points\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Fitment\u003c\/h2\u003e\u003cp\u003eFits 2000-2002 Audi TT Quattro, N\/A, to chassis 8N-2-015 000. Fits 1990-1993 Volvo 240, front. Fits 1991-1993 Volvo 240, front, where 2 required. Fits 1986 BMW 735i, front, up to Dec 1986. Fits 1985 BMW 735i, front. Fits 1984 Volvo DL, front. Fits 1984 Volvo GLE, front. Fits 1977-1983 BMW 320i, front. Fits 1979-1981 BMW 528i, front, where 4 required. Fits 1977-1978 BMW 530i, front, where 4 required. Fits 1975 BMW 530i, front, where 4 required. Fits 1976 BMW 530i, front, where 4 required, to 1\/76; front, where 4 required, from 9\/76; and front, where 4 required, from 2\/76 to 8\/76.\u003c\/p\u003e\u003cp\u003eVerify thread size, flare type, and chassis breakpoints before installation. Inspect mating hard lines, seals, and mounting points for wear or corrosion, and confirm the hose routing matches the original hydraulic line path on the vehicle.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is built around broad application coverage and updated catalog support for hydraulic service parts. The 150.34001 is DOT approved and specified with OE-style connection details for consistent fitment on listed BMW, Volvo, and Audi applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43643441250485,"sku":"BKNJ-150.34001","price":19.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15034001_Fro.jpg?v=1774988663"},{"product_id":"centric-150-35304-clutch-hydraulic-hose","title":"Centric 150.35304 Clutch Hydraulic Hose - Rear","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric 150.35304 clutch hydraulic hose is a DOT approved replacement hose built with a black EPDM rubber outer sleeve and metal female fittings at both ends. It is a direct-fit hydraulic line for select Volkswagen, Audi, and Mercedes-Benz applications, including Golf, Beetle, Jetta, TT Quattro, and several rear Mercedes-Benz models.\u003c\/p\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ brake hydraulic program, which covers master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters. This line focuses on hydraulic service parts for vehicles that need accurate fitment and dependable fluid transfer.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for regulated hydraulic brake and clutch service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for durable hose construction\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eBubble flare ends with M10-1.00 thread size\u003c\/li\u003e\n\u003cli\u003eOverall length: 11.890 in. \/ 302.00 mm\u003c\/li\u003e\n\u003cli\u003eFits rear Mercedes-Benz applications and select Volkswagen and Audi models\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.35304\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eCentric 150.35304 is a clutch hydraulic hose engineered for vehicles that use bubble flare, M10-1.00 female connections. The hose uses an EPDM rubber outer sleeve and does not include a Teflon liner, mounting hardware, grommets, brackets, seals, shields, or banjo bolt\/clip components. For buyers searching for a Volkswagen Golf clutch hydraulic hose, Volkswagen Jetta hydraulic hose, Audi TT Quattro clutch line, or Mercedes-Benz rear hydraulic hose, this part number provides a focused OE-style service replacement.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H38514 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2002-2005 Volkswagen Golf, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Volkswagen Beetle, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Volkswagen Jetta, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Audi TT Quattro, N\/A; from chassis 8N-2-015 001\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Mercedes-Benz 560SEC, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Mercedes-Benz 560SEL, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1986-1989 Mercedes-Benz 560SL, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 500SEC, Rear; C126\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 500SEL, Rear; C126\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify end fitting type, thread size, flare type, and overall length before installation. This hose uses female-to-female M10-1.00 bubble flare connections, so it should be matched to the original hydraulic routing and port style on the vehicle. Confirm the chassis note for 2000-2002 Audi TT Quattro applications and the rear-position requirement on Mercedes-Benz fitments before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric includes this hose in its brake hydraulic program, which is built around service parts for hydraulic brake and clutch systems. The DOT approval and application-specific fitment support selection for Volkswagen, Audi, and Mercedes-Benz vehicles.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646241865909,"sku":"BKNJ-150.35304","price":19.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15035304_Fro_f223b011-c7be-435d-9f47-2c030cc836c4.jpg?v=1774988690"},{"product_id":"centric-150-42304-clutch-hydraulic-hose","title":"Centric 150.42304 Clutch Hydraulic Hose - Rear Lower or Rear Right","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose 150.42304\u003c\/h2\u003e\u003cp\u003eCentric 150.42304 is a DOT-approved clutch hydraulic hose built with an EPDM rubber outer sleeve and metal end fittings for Nissan applications that use a male-to-female inverted connection. It is listed for rear lower and rear right positions on select Nissan 200SX, 300ZX, 510, and 810 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for hydraulic brake and clutch service applications\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal end fittings with M10-1.00 threads\u003c\/li\u003e\n\u003cli\u003eMale end 1 and female inverted end 2 configuration\u003c\/li\u003e\n\u003cli\u003eGasket or seal included\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003cli\u003eCross-reference: Dorman - First Stop H96868\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis Centric Premium Brake Hydraulic Hoses part is engineered for Nissan hydraulic line service where a direct-fit clutch hydraulic hose is required. Part number 150.42304 uses a black EPDM rubber construction, metal fittings, and a standard M10-1.00 thread pattern to match the listed Nissan fitments. The hose is cataloged for rear lower and rear right locations, with application notes that include 1989 Nissan 300ZX rear lower, 1987-1988 Nissan 200SX rear lower, 1984-1988 Nissan 300ZX rear lower, and earlier Nissan 510 and 810 applications. This part number, 150.42304, is also cross-referenced to Gates 38144 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at a worn hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or aging rubber hydraulic lines\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch circuit\u003c\/li\u003e\n\u003cli\u003eService replacement for Nissan 200SX, 300ZX, 510, and 810 hydraulic line applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, model, and position before installation. This hose uses a male end 1 and female inverted end 2 with M10-1.00 threads, and the listing includes a clip and gasket or seal but does not include mounting hardware, brackets, grommets, or a shield. Confirm routing, connection style, and fitment notes such as rear lower or rear right before final assembly on Nissan 200SX and Nissan 300ZX applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program covers master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters, giving this hose part of a broad hydraulic component lineup. The DOT-approved designation supports use in regulated hydraulic service applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646493524149,"sku":"BKNJ-150.42304","price":17.86,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15042304_Fro.jpg?v=1774988800"},{"product_id":"centric-150-44001-clutch-hydraulic-hose","title":"Centric 150.44001 Clutch Hydraulic Hose - Front Upper or Rear Left","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric 150.44001 clutch hydraulic hose is a DOT approved replacement hose built with a black EPDM rubber outer sleeve and metal female fittings at both ends. It is a direct-fit hydraulic line for select Toyota applications, including Toyota T100, 4Runner, Pickup, Tercel, Celica, and Corolla models.\u003c\/p\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of a broad hydraulic program that covers brake master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters. The 150.44001 hose follows that OE-style service approach with the correct inverted flare, M10-1.00 thread size, and application-specific length for the listed Toyota fitments.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for brake or clutch hydraulic service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for durable under-vehicle use\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends with inverted flare design\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends for listed Toyota applications\u003c\/li\u003e\n\u003cli\u003eBlack finish for a clean OE-style appearance\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.44001 for easy catalog matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment and Application Details\u003c\/h2\u003e\u003cp\u003eCompatible with select Toyota hydraulic applications, including Fits 1994-1998 Toyota T100, N\/A; Fits 1988-1995 Toyota 4Runner, N\/A; Fits 1988-1995 Toyota Pickup, N\/A; Fits 1987-1990 Toyota Tercel, N\/A; Fits 1983-1986 Toyota Tercel, Rear Left; Fits 1975-1981 Toyota Celica, Front Upper; Fits 1971-1973 Toyota Celica, Front Upper; Fits 1970-1979 Toyota Corolla, Front Upper; and 1974 Toyota Celica, Front Upper in the listed production splits. This part number, 150.44001, also cross-references Dorman - First Stop H96764 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Hose Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leaks from a cracked or aged hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch or brake pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the original hose fittings\u003c\/li\u003e\n\u003cli\u003eService issues on Toyota T100, 4Runner, Pickup, Tercel, Celica, and Corolla hydraulic lines\u003c\/li\u003e\n\u003cli\u003eReplacement needs for a DOT approved inverted-flare hose assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and position before installation, since this hose is listed for multiple Toyota applications and positions. Confirm the M10-1.00 thread size, inverted flare ends, and overall length of 11.260 inches (286.00 mm) against the original part before removal. Mounting hardware, grommets, brackets, seals, and shields are not included.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s hydraulic program is organized as a broad OE-style replacement line for brake and hydraulic service parts. The 150.44001 clutch hydraulic hose is DOT approved and built to match the listed Toyota fitments with the specified fitting style, material, and length.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646512398517,"sku":"BKNJ-150.44001","price":13.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044001_Fro.jpg?v=1774988828"},{"product_id":"centric-150-44012-clutch-hydraulic-hose","title":"Centric 150.44012 Clutch Hydraulic Hose - Front or Front Upper","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line includes hydraulic components built for brake and clutch service, and part number 150.44012 is a DOT-approved clutch hydraulic hose for select Toyota and Lexus applications. It uses a black EPDM rubber outer sleeve with metal female inverted-flare ends and M10-1.00 threads for a direct-fit hydraulic connection.\u003c\/p\u003e\u003cp\u003eFits 1993-1998 Toyota Supra, N\/A; Fits 1992-1997 Lexus SC300, N\/A; Fits 1982-1984 Toyota Corona, Front; Fits 1985 Toyota Celica, Front Upper; Fits 1979-1982 Toyota Corona, Front.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for hydraulic system service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal female fittings with inverted flare ends\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003eBlack finish for a factory-style appearance\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.44012\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ hydraulic program, which covers brake and clutch hydraulic service components across a broad range of applications. This clutch hydraulic hose is built for vehicles that use a hydraulic linkage between the master cylinder and clutch release system, helping maintain consistent fluid transfer in the clutch circuit. The 150.44012 hose is listed for Toyota Supra, Lexus SC300, Toyota Celica, and Toyota Corona applications, including front and front upper positions where specified.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H38030 for the same application. The Centric 150.44012 is also referenced by other aftermarket numbers, including Four Seasons 77377.\u003c\/p\u003e\u003ch2\u003eWhat This Hose Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFluid leakage in the clutch hydraulic line\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose wear\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage at the hydraulic fittings\u003c\/li\u003e\n\u003cli\u003eService replacement for aging Toyota and Lexus clutch hydraulic routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, model, and hydraulic line routing before installation. Confirm both end fittings use M10-1.00 inverted-flare connections and compare the hose length and position against the removed part. Inspect the mating hard lines, clips, and sealing surfaces for wear or corrosion before assembly. Because mounting hardware, grommets, brackets, and seals are not included, reuse or replace related components as needed during service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized to cover master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters, giving this hose the backing of a focused hydraulic parts line. Part number 150.44012 is DOT approved and built for direct hydraulic service on the listed Toyota and Lexus applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646512824501,"sku":"BKNJ-150.44012","price":19.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044012_Fro.jpg?v=1774988830"},{"product_id":"centric-150-44019-clutch-hydraulic-hose","title":"Centric 150.44019 Clutch Hydraulic Hose - Front, Front Upper or Rear Left Upper","description":"\u003ch2\u003eCentric 150.44019 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eCentric 150.44019 is a DOT approved clutch hydraulic hose built with a black EPDM rubber outer sleeve and metal female inverted-flare fittings at both ends. It is listed for a range of Toyota and Lexus applications, including Toyota Pickup, 4Runner, Camry, T100, Celica, Corolla, Land Cruiser, and Lexus LX470 and ES300.\u003c\/p\u003e\u003ch2\u003eCentric Premium Brake Hydraulic Hoses\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line focuses on hydraulic brake and clutch service parts with broad coverage for import vehicles. For shoppers searching for a Toyota clutch hydraulic hose or a Lexus hydraulic hose replacement, this line provides OE-style fitment details and application-specific hardware notes to help match the correct part.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for hydraulic brake and clutch service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eInverted flare ends with M10-1.00 thread size\u003c\/li\u003e\n\u003cli\u003eOverall length: 14.370 in. \/ 365.00 mm\u003c\/li\u003e\n\u003cli\u003eIncludes clip provision; clip quantity listed as 2\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.44019\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Centric clutch hydraulic hose is built for direct replacement use on confirmed Toyota and Lexus applications. The hose uses EPDM rubber for the outer sleeve, metal end fittings, and inverted flare connections to match the hydraulic routing used on the listed vehicles. If you are searching for a 1993-1998 Toyota T100 front clutch hydraulic hose or a 2000-2007 Lexus LX470 rear left upper hydraulic hose, 150.44019 is the cataloged part number to review. This part cross-references Gates 1270 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at the hose assembly\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose wear\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eFitment issues when replacing an aging Toyota or Lexus hydraulic hose\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify the vehicle position before ordering; fitment varies by front, front upper, rear left upper, and N\/A applications.\u003c\/li\u003e\n\u003cli\u003eConfirm M10-1.00 thread size and inverted flare connection style before installation.\u003c\/li\u003e\n\u003cli\u003eInspect clips and mounting points during replacement, since mounting hardware, brackets, grommets, and seals are not included.\u003c\/li\u003e\n\u003cli\u003eBleed the hydraulic system after installation to remove air from the circuit.\u003c\/li\u003e\n\u003cli\u003eCheck the hose routing for clearance and secure attachment to prevent twisting or contact wear.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program covers master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters, giving the brand broad catalog support for hydraulic service parts. Part number 150.44019 is cataloged for multiple Toyota and Lexus applications, including 1978-1983 Toyota Pickup, 1989-1995 Toyota Pickup, 1989-1994 Toyota 4Runner, 1992-1996 Toyota Camry, 1993-1998 Toyota T100, 2003-2007 Toyota Land Cruiser, and 2000-2007 Lexus LX470.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646513610933,"sku":"BKNJ-150.44019","price":16.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044019_Fro.jpg?v=1774988831"},{"product_id":"centric-150-44029-clutch-hydraulic-hose","title":"Centric 150.44029 Clutch Hydraulic Hose - Front","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers OE-style hydraulic components for brake and clutch service, and this Centric clutch hydraulic hose is built for direct replacement use on select Toyota applications. Part number 150.44029 features DOT approval, black EPDM rubber outer sleeve construction, and metal female inverted-flare ends with M10-1.00 threads for a precise hydraulic connection.\u003c\/p\u003e\u003cp\u003eCompatible With Toyota Tundra, Toyota Paseo, Toyota 4Runner, Toyota Tercel, and Toyota Pickup applications listed below, this hose supports clutch hydraulic routing where a durable, road-ready replacement is needed. The Centric 150.44029 is also cross-referenced to Dorman H621872 for the same application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eInverted flare end design\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003eBlack finish for OE-style appearance\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ hydraulic program, which covers brake and hydraulic service components across master cylinders, wheel cylinders, hoses, repair kits, and remanufactured boosters. This clutch hydraulic hose is engineered as a direct-fit replacement for select Toyota models, including 2000-2004 Toyota Tundra, 1996-1997 Toyota 4Runner, 1991-1994 Toyota Tercel, 1984-1988 Toyota Pickup, and Toyota Paseo applications with the listed production notes. Part number 150.44029 is built with metal end fittings, inverted flare connections, and a flexible EPDM rubber sleeve to support hydraulic line routing in the clutch system.\u003c\/p\u003e\u003cp\u003eFits 2000-2004 Toyota Tundra, N\/A. Fits 1996-1997 Toyota 4Runner, N\/A. Fits 1991-1994 Toyota Tercel, N\/A. Fits 1984-1988 Toyota Pickup, Front. Fits 1992-1996 Toyota Paseo, N\/A. Fits 1998 Toyota Paseo, N\/A, Fr 12\/97; To 2\/98. Fits 1999 Toyota Paseo, N\/A, Fr 2\/98.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic fluid leakage from a worn hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by line deterioration\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or aging rubber hydraulic hose material\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eRestricted hydraulic flow from a damaged clutch line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the end fitting type, thread size, and routing before installation. This hose uses female inverted-flare connections with M10-1.00 threads and does not include mounting hardware, brackets, grommets, seals, or shields. Confirm the vehicle’s production date notes for Toyota Paseo applications, and inspect the surrounding hydraulic components for wear or leakage before completing the repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eThis Centric clutch hydraulic hose is DOT approved and built within Centric Parts’ established hydraulic component program. The brand’s brake hydraulic line includes master cylinders, wheel cylinders, hoses, repair kits, and remanufactured boosters, supporting a focused OE-style replacement approach for Toyota clutch hydraulic service.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646516199605,"sku":"BKNJ-150.44029","price":16.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044029_Fro.jpg?v=1774988833"},{"product_id":"centric-150-44044-clutch-hydraulic-hose","title":"Centric 150.44044 Clutch Hydraulic Hose - Front","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose for Toyota MR2\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line includes hydraulic components built for direct-fit service, and this Centric clutch hydraulic hose is listed for select Toyota MR2 applications. Part number 150.44044 is a DOT-approved hose with a black EPDM rubber outer sleeve and metal end fittings for a factory-style hydraulic connection.\u003c\/p\u003e\u003cp\u003eCompatible With 1985-1989 Toyota MR2 front applications, this hose is also listed for 1986-1989 Toyota MR2 and specific 1985 and 1989 MR2 build-date notes. If you are searching for a Toyota MR2 clutch hydraulic hose, Centric 150.44044 provides the fitment and connection details needed for a direct replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for hydraulic brake and clutch service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal banjo fitting on end 1 and metal female inverted fitting on end 2\u003c\/li\u003e\n\u003cli\u003eGasket or seal included\u003c\/li\u003e\n\u003cli\u003eBanjo bolt and clip references available for matching service parts\u003c\/li\u003e\n\u003cli\u003eOverall length listed at 19.291 in. \/ 490.00 mm\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric 150.44044 is a clutch hydraulic hose built around the Centric Premium Brake Hydraulic Hoses program, which covers hydraulic service parts for brake and clutch systems. This hose uses an EPDM rubber outer sleeve, metal fittings, and an inverted female connection at end 2 with M10-1.00 thread size. The banjo-style end 1 uses a 10.0 mm thread size, and the hose is listed with seal hardware details for service matching.\u003c\/p\u003e\u003cp\u003eFor Toyota MR2 owners, this part number 150.44044 is a direct-reference option for front-position hydraulic service on listed 1985-1989 Toyota MR2 applications. It also cross-references Dorman - First Stop H38787 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at the hose connection\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose wear\u003c\/li\u003e\n\u003cli\u003eCracked or aged rubber hose material\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage at the fitting ends\u003c\/li\u003e\n\u003cli\u003eService replacement for a worn Toyota MR2 clutch hydraulic hose\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle build date and position before ordering, since the fitment list includes 1985 and 1989 Toyota MR2 notes tied to production timing. Confirm the banjo and inverted female thread specifications, and inspect the mating surfaces, seals, and line routing before installation. This hose is listed without mounting hardware, brackets, grommets, or shield components.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized to cover master cylinders, wheel cylinders, brake hoses, repair kits, and related hydraulic service parts in one catalog family. Part number 150.44044 is DOT approved and built to the listed OE-style connection specifications for the Toyota MR2 applications shown.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646518624437,"sku":"BKNJ-150.44044","price":25.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044044_Fro.jpg?v=1774988835"},{"product_id":"centric-150-44304-clutch-hydraulic-hose","title":"Centric 150.44304 Clutch Hydraulic Hose - Front or Rear","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line includes OE-style hydraulic components for brake and clutch applications, and this Centric clutch hydraulic hose is built for direct replacement service on select Toyota, Geo, and Chevrolet vehicles. Part number 150.44304 is DOT approved and uses a black EPDM rubber outer sleeve with metal female ends for dependable hydraulic routing.\u003c\/p\u003e\u003cp\u003eCompatible With 1983-1995 Toyota Camry, Corolla, Celica, and Pickup applications, plus 1985-1992 Chevrolet Nova and Geo Prizm rear positions. This Centric 150.44304 hose is a direct-fit hydraulic replacement for vehicles that use M10-1.00 inverted flare connections.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch and brake system service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for flexible routing and resistance to everyday road exposure\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends with inverted flare design\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends for confirmed applications\u003c\/li\u003e\n\u003cli\u003eDirect replacement part number 150.44304 for select Toyota, Geo, and Chevrolet models\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line coverage for hydraulic repair needs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eCentric 150.44304 is a clutch hydraulic hose built for vehicles that require a hydraulic line with female metal ends, inverted flare connections, and a black EPDM rubber outer sleeve. The hose measures 13.780 inches overall and is listed with clip provisions and clip compatibility for the application. It does not include mounting hardware, grommets, brackets, seals, or a shield.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H36738 and H38788 for the same application. It also aligns with other aftermarket references used on Toyota Pickup, Toyota Corolla, Toyota Camry, Toyota Celica, Geo Prizm, and Chevrolet Nova hydraulic service applications. Part number 150.44304 is a practical replacement when the original clutch hydraulic hose is worn, leaking, or no longer holding consistent hydraulic pressure.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage from a cracked or aged clutch hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eRestricted hydraulic flow from internal hose wear\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage at the original hose fittings\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged line on Toyota Pickup, Corolla, Camry, Celica, Geo Prizm, or Chevrolet Nova applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify end thread size, flare type, and routing before installation. This hose uses M10-1.00 female inverted flare ends and is intended for confirmed vehicle applications only. Inspect the mating hard lines, clips, and mounting points for wear or corrosion before installing Centric 150.44304. After installation, bleed the hydraulic system according to the vehicle service procedure and check for leaks at both connections.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program covers master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters, giving this part line broad hydraulic system coverage. The hose is DOT approved and built to meet the requirements of the listed applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646551130293,"sku":"BKNJ-150.44304","price":19.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044304_Fro.jpg?v=1774988861"},{"product_id":"centric-150-44305-clutch-hydraulic-hose","title":"Centric 150.44305 Clutch Hydraulic Hose - Rear","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers OE-style hydraulic hose construction for vehicles that need consistent clutch or brake fluid transfer. Part number 150.44305 is a DOT approved hose with black EPDM rubber outer sleeve and metal end fittings for a direct-fit service replacement on select Toyota applications.\u003c\/p\u003e\u003cp\u003eCompatible with 1979-1981 Toyota Celica, 1981-1984 Toyota Starlet, 1985-1987 Toyota Land Cruiser, and 1986-1987 Toyota Van, this hose supports hydraulic system repair where the original line has aged, cracked, or lost pressure. The Centric 150.44305 is also cross-referenced to Dorman - First Stop H77376 for the same application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch or brake hydraulic service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for flexible routing and fluid-system durability\u003c\/li\u003e\n\u003cli\u003eMetal male-to-female end fittings with inverted flare connections\u003c\/li\u003e\n\u003cli\u003eEnd thread size: M10-1.00 on both ends\u003c\/li\u003e\n\u003cli\u003eIncludes clip and clip quantity reference for OE-style retention\u003c\/li\u003e\n\u003cli\u003eOverall length: 12.598 in. \/ 320.00 mm\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ hydraulic program, which covers brake master and wheel cylinders, brake hoses, repair kits, and remanufactured power boosters. This part number 150.44305 is built with metal fittings, inverted flare ends, and an EPDM rubber outer sleeve to match the hydraulic routing and connection style used on the listed Toyota vehicles. It is a practical replacement for a worn Toyota Celica clutch hydraulic hose, Toyota Starlet rear hydraulic line service, Toyota Land Cruiser hydraulic hose replacement, or Toyota Van rear hydraulic hose repair.\u003c\/p\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid seepage at the hose or fitting\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or weathered rubber hose material\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the line\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the end fittings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify thread size, fitting style, and routing before installation. This hose uses M10-1.00 male and female inverted flare connections and does not include mounting hardware, brackets, grommets, seals, or a shield. Inspect the mating hard lines, clips, and retaining points for wear before reassembly, and bleed the hydraulic system after installation to restore proper pedal response.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDOT approved construction supports regulated hydraulic service requirements. Centric’s brake hydraulic program is organized around OE-style replacement coverage for master cylinders, wheel cylinders, hoses, repair kits, and boosters, giving this hose a focused fitment and specification profile for service work on select Toyota models.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646551326901,"sku":"BKNJ-150.44305","price":21.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044305_Fro.jpg?v=1774988862"},{"product_id":"centric-150-44316-clutch-hydraulic-hose","title":"Centric 150.44316 Clutch Hydraulic Hose - Rear Lower","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose 150.44316\u003c\/h2\u003e\u003cp\u003eCentric 150.44316 is a DOT-approved clutch hydraulic hose built with a black EPDM rubber outer sleeve and metal end fittings for direct hydraulic service. It is listed for rear lower applications on select Toyota models, including Toyota Sienna, Toyota Cressida, Toyota Celica, and Toyota Corona.\u003c\/p\u003e\u003ch2\u003eCentric Premium Brake Hydraulic Hoses\u003c\/h2\u003e\u003cp\u003eThis hose comes from Centric Premium Brake Hydraulic Hoses, a product line focused on brake and hydraulic service components such as master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters. For buyers searching for a Toyota clutch hydraulic hose or a rear lower hydraulic hose replacement, this line provides OE-style coverage across multiple vehicle platforms.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for hydraulic brake and clutch service\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal end fittings with male and female connections\u003c\/li\u003e\n\u003cli\u003eInverted flare ends with M10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 210.00\u003c\/li\u003e\n\u003cli\u003eClip included; clip quantity listed as 1\u003c\/li\u003e\n\u003cli\u003eCross-reference example: Dorman - First Stop H38110\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2004-2010 Toyota Sienna, rear lower.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1988 Toyota Cressida, rear lower.\u003c\/li\u003e\n\u003cli\u003eFits 1983-1984 Toyota Cressida, rear lower.\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Toyota Celica, N\/A, 22REC Engine.\u003c\/li\u003e\n\u003cli\u003eFits 1985 Toyota Cressida, rear lower, To 1\/85.\u003c\/li\u003e\n\u003cli\u003eFits 1985 Toyota Cressida, rear lower, Fr 8\/85.\u003c\/li\u003e\n\u003cli\u003eFits 1985 Toyota Cressida, rear lower, Fr 2\/85 - To 7\/85.\u003c\/li\u003e\n\u003cli\u003eFits 1983 Toyota Celica, N\/A, 22R; 22REC Engine.\u003c\/li\u003e\n\u003cli\u003eFits 1978-1982 Toyota Celica, N\/A.\u003c\/li\u003e\n\u003cli\u003eFits 1979-1982 Toyota Corona, N\/A.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Hose Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at a worn clutch or brake hose\u003c\/li\u003e\n\u003cli\u003eSoft, inconsistent pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eCracking or hardening in an aging EPDM rubber hose\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eService replacement for a Toyota Sienna, Toyota Cressida, Toyota Celica, or Toyota Corona hydraulic line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify thread size, flare type, and routing before installation. This hose uses male and female metal fittings with inverted flares and does not include mounting hardware, grommets, brackets, gasket, seal, or shield. Confirm the rear lower routing and vehicle build date notes for 1985 Toyota Cressida applications before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is built around broad hydraulic coverage and up-to-date catalog support for brake and clutch service parts. Centric 150.44316 is a DOT-approved replacement hose for select Toyota applications and is backed by Centric Parts product-line engineering and application coverage.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646553850037,"sku":"BKNJ-150.44316","price":18.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044316_Fro.jpg?v=1774988863"},{"product_id":"centric-150-44325-clutch-hydraulic-hose","title":"Centric 150.44325 Clutch Hydraulic Hose - Rear","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers OE-style hydraulic components for vehicles that need precise fluid transfer and dependable pedal response. Part number 150.44325 is a DOT approved clutch hydraulic hose with a black EPDM rubber outer sleeve and metal inverted fittings for a secure connection.\u003c\/p\u003e\u003cp\u003eCompatible with select Toyota Corona rear applications and Toyota Land Cruiser models, this hose is built for direct-fit service where the original hydraulic line has aged, cracked, or begun to leak. The Centric Premium Brake Hydraulic Hoses program covers a broad range of brake and hydraulic service parts, giving technicians a focused replacement option for hydraulic repairs.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved for road-use compliance\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal male and female inverted fittings\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003e15.118 in. overall length\u003c\/li\u003e\n\u003cli\u003eIncludes clip; clip quantity listed as 1\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.44325\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric 150.44325 is a clutch hydraulic hose designed for hydraulic line replacement where the original hose has deteriorated from heat, moisture, or age. The hose uses EPDM rubber for the outer sleeve and metal end fittings with inverted flare connections to support a secure hydraulic seal. It is black in color and does not include mounting hardware, grommets, brackets, gaskets, shields, or a Teflon liner.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H36878 for the same application. It is listed for rear fitment on 1967-1968 Toyota Corona, 1969-1973 Toyota Corona, and 1968-1969 Toyota Land Cruiser applications, with year-specific notes for certain Toyota Corona builds.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage from a worn clutch hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose expansion or deterioration\u003c\/li\u003e\n\u003cli\u003eCracked or weathered rubber hydraulic lines\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eService replacement for damaged inverted-flare hose connections\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify end thread size, fitting type, and overall length before installation. Confirm the vehicle build date for Toyota Corona applications with date-specific notes, including 1970-1972 models. Inspect the mating hard lines, clips, and connection points for corrosion or damage before installing the new hose.\u003c\/p\u003e\u003cp\u003eFor fitment, this part fits 1967-1968 Toyota Corona, rear; fits 1969 Toyota Corona, rear; fits 1970 Toyota Corona, rear; fits 1971 Toyota Corona, rear; fits 1972 Toyota Corona, rear; fits 1973 Toyota Corona, rear; and fits 1968-1969 Toyota Land Cruiser, N\/A.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized as a broad OE-style replacement line for brake and hydraulic service needs, with coverage that includes hoses, cylinders, repair kits, and related components. Part number 150.44325 is DOT approved and built to match the listed hydraulic specifications for the confirmed applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646554702005,"sku":"BKNJ-150.44325","price":22.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044325_Fro.jpg?v=1774988864"},{"product_id":"centric-150-44334-clutch-hydraulic-hose","title":"Centric 150.44334 Clutch Hydraulic Hose - Front Upper, Rear or Rear Lower","description":"\u003ch2\u003eCentric Brake Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line is built for direct hydraulic brake service on select Toyota applications. Part number 150.44334 is a DOT approved hose with a black EPDM rubber outer sleeve, metal end fittings, and inverted flare connections for a secure brake-fluid seal.\u003c\/p\u003e\u003cp\u003eCompatible With 1975-1987 Toyota Celica, Toyota Corolla, and Toyota Land Cruiser applications listed below, this hose supports rear, rear lower, front upper, and N\/A-position fitments depending on the vehicle. The Centric 150.44334 is a practical replacement for worn, cracked, or leaking hydraulic hose assemblies.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved brake hydraulic hose\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eMetal male and female end fittings\u003c\/li\u003e\n\u003cli\u003eInverted flare ends with M10-1.00 thread size\u003c\/li\u003e\n\u003cli\u003eClip included; clip quantity listed as 1\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003cli\u003ePart number 150.44334\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric Premium Brake Hydraulic Hoses are part of Centric Parts’ hydraulic brake program, which covers core service items such as brake hoses, master and wheel cylinders, repair kits, and remanufactured boosters. This hose uses an EPDM rubber outer sleeve for hydraulic brake service and metal fittings at both ends for a direct connection to the vehicle’s brake system. The 150.44334 application list includes Toyota Celica, Toyota Corolla, and Toyota Land Cruiser fitments across multiple years and positions.\u003c\/p\u003e\u003cp\u003eThis part cross-references Gates 38122 and Raybestos Brakes BH36937 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrake fluid seepage from a cracked or aged hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent brake pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eVisible swelling, splitting, or surface damage on the hydraulic line\u003c\/li\u003e\n\u003cli\u003eRestricted brake fluid flow from internal hose wear\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged Toyota Celica, Corolla, or Land Cruiser brake hose\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle position and thread size before installation. This hose uses M10-1.00 threads, inverted flare ends, and metal fittings, so the connection points should be inspected for wear, corrosion, or damaged sealing surfaces before assembly. The listing does not include mounting hardware, brackets, grommets, seals, or a shield.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 1976-1983 Toyota Land Cruiser, front upper\u003c\/li\u003e\n\u003cli\u003eFits 1980-1982 Toyota Corolla, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1979-1981 Toyota Celica, rear lower\u003c\/li\u003e\n\u003cli\u003eFits 1977 Toyota Celica, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1975-1976 Toyota Celica, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1987 Toyota Corolla, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized to cover a broad range of brake service needs with current catalog support and DOT approved hose applications. Part number 150.44334 is specified for the listed Toyota fitments and positions, making it a direct-reference replacement for the applications shown.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646555685045,"sku":"BKNJ-150.44334","price":17.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044334_Fro_989b6b3a-8da5-4594-a178-54a7e9308742.jpg?v=1774988865"},{"product_id":"centric-150-44356-clutch-hydraulic-hose","title":"Centric 150.44356 Clutch Hydraulic Hose - Rear","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line includes hydraulic components built for brake and clutch service, and this Centric clutch hydraulic hose is a direct-fit replacement for select Toyota applications. Part number 150.44356 is DOT approved and uses black EPDM rubber construction with metal female ends for a secure hydraulic connection.\u003c\/p\u003e\u003cp\u003eCompatible with 1997-2001 Toyota Camry and 1990-1993 Toyota Celica rear applications, this hose supports hydraulic fluid transfer in clutch or brake-related hydraulic systems where the original hose has aged, cracked, or begun to leak. This part number 150.44356 is built for straightforward replacement on the listed Toyota models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for road-use compliance\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for hydraulic service\u003c\/li\u003e\n\u003cli\u003eMetal female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eInverted flare ends with M10-1.00 thread size\u003c\/li\u003e\n\u003cli\u003eBlack finish for OE-style appearance\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eCentric 150.44356 is a clutch hydraulic hose designed for select Toyota vehicles and built within Centric’s brake hydraulic program, which covers master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters. The hose uses EPDM rubber for the outer sleeve, metal end fittings, and inverted flare connections to match the hydraulic system requirements of the listed applications. This part cross-references Dorman - First Stop H38790 for the same application.\u003c\/p\u003e\u003cp\u003eFor Toyota Camry and Toyota Celica owners searching for a replacement clutch hydraulic hose, 150.44356 provides a direct service part for restoring hydraulic line integrity on the specified fitments.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at the hose body or end fittings\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch hydraulic pedal response\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the original hose connections\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch or related hydraulic circuit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and rear-position fitment before installation. Confirm M10-1.00 thread size, inverted flare ends, and routing length against the original hose. Replace any worn clips or mounting points as needed, since mounting hardware, brackets, grommets, seals, and shields are not included.\u003c\/p\u003e\u003cp\u003eAfter installation, inspect all connections for seepage and bleed the hydraulic system according to factory service procedures. For 1997-2001 Toyota Camry and 1990-1993 Toyota Celica rear applications, confirm the hose routing matches the original layout before returning the vehicle to service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is built around a broad catalog of hydraulic service parts for brake and clutch repair, with DOT-approved components selected for listed vehicle applications. Part number 150.44356 is engineered to meet the fitment and connection requirements of the specified Toyota models.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646558404789,"sku":"BKNJ-150.44356","price":23.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044356_Fro.jpg?v=1774988869"},{"product_id":"centric-150-44372-clutch-hydraulic-hose","title":"Centric 150.44372 Clutch Hydraulic Hose - Rear, Rear Left Upper or Rear Upper","description":"\u003ch2\u003eCentric Premium Brake Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line is built for direct hydraulic brake service on select Toyota, Lexus, Scion, Geo, and Chevrolet applications. Part number 150.44372 is a DOT approved clutch hydraulic hose with black EPDM rubber outer sleeve construction and metal female inverted fittings at both ends.\u003c\/p\u003e\u003cp\u003eUse this hose when you need a replacement for rear upper, rear left upper, rear inner, or rear brake hydraulic routing on supported vehicles such as the Toyota 4Runner, Toyota Tacoma, and Lexus GX460. Centric 150.44372 is engineered for fitment-focused repair work where correct thread size, flare type, and hose length matter.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved brake hydraulic hose for service replacement\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for brake system use\u003c\/li\u003e\n\u003cli\u003eMetal female fittings with inverted flare ends on both sides\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003eDirect-fit application coverage for rear and rear upper hydraulic routing\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric 150.44372 is part of the Centric Premium Brake Hydraulic Hoses program, a hydraulic parts line that covers brake hoses and related brake hydraulic components for a wide range of repair needs. This hose uses a black EPDM rubber outer sleeve, metal end fittings, and inverted flare connections to match the specified vehicle applications. The hose measures 12.756 in overall length and uses M10-1.00 threads at both ends. It is supplied without mounting hardware, brackets, grommets, seals, or a shield.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H380516 for the same application. It also cross-references Raybestos Brakes BH380516 for select applications.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrake fluid leakage at a damaged or corroded hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent brake pedal feel caused by hydraulic line wear\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or aged rubber hose sections\u003c\/li\u003e\n\u003cli\u003eRestricted brake fluid flow from internal hose deterioration\u003c\/li\u003e\n\u003cli\u003eFailed rear brake hydraulic routing on supported Toyota and Lexus models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, make, model, and hose position before installation. Confirm the inverted flare ends, M10-1.00 thread size, and overall length match the original hose routing. Inspect adjacent hard lines, clips, and mounting points for corrosion or damage before connecting the new hose. After installation, bleed the brake system according to factory procedure and check all connections for leaks.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized to cover master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters for service-focused brake repairs. Part number 150.44372 is DOT approved and built for the specified fitment applications, including Toyota 4Runner, Toyota Tacoma, and Lexus GX460 coverage.\u003c\/p\u003e\u003ch2\u003eFitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2016-2021 Lexus GX460, Rear Upper\u003c\/li\u003e\n\u003cli\u003eFits 2020-2021 Lexus LX570, Rear Left Upper\u003c\/li\u003e\n\u003cli\u003eFits 2015-2016 Lexus LX570, Rear Left Upper\u003c\/li\u003e\n\u003cli\u003eFits 2014-2021 Toyota 4Runner, Rear Upper\u003c\/li\u003e\n\u003cli\u003eFits 2016-2021 Toyota Land Cruiser, Rear Left Upper\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 Lexus GX460, Rear Inner\u003c\/li\u003e\n\u003cli\u003eFits 2005-2015 Toyota Tacoma, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2014 Toyota FJ Cruiser, Rear Inner\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xA, Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xA, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xB, Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xB, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Toyota Echo, Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2005 Toyota RAV4, Rear Upper\u003c\/li\u003e\n\u003cli\u003eFits 1996-2005 Toyota RAV4, Rear\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Toyota RAV4, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1998-2003 Toyota Sienna, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1998-2002 Chevrolet Prizm, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1996-2002 Toyota Corolla, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1996-1997 Geo Prizm, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1995 Geo Prizm, Rear\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646561124533,"sku":"BKNJ-150.44372","price":22.59,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15044372_Fro_c513391e-6e01-4cbe-9fe1-4a9fbb3f6bfe.jpg?v=1774988873"},{"product_id":"centric-150-45310-clutch-hydraulic-hose","title":"Centric 150.45310 Clutch Hydraulic Hose - Rear Upper","description":"\u003ch2\u003eCentric Clutch Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers OE-style hydraulic hose coverage with application-specific fitment and durable construction. Part number 150.45310 is a DOT approved clutch hydraulic hose with EPDM rubber outer sleeve material, metal fittings, and a black finish for a clean, factory-style replacement.\u003c\/p\u003e\u003cp\u003eCompatible With Mazda 626 and Mazda RX-7 applications listed below, this hose is built for direct hydraulic line replacement where the original clutch hose has aged, cracked, or begun to leak. The Centric Premium Brake Hydraulic Hoses program also draws from Centric Parts’ broader brake hydraulic catalog, which includes master cylinders, wheel cylinders, brake hoses, repair kits, and remanufactured power boosters.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved hydraulic hose for clutch system service\u003c\/li\u003e\n\u003cli\u003eEPDM rubber outer sleeve for brake and clutch hydraulic use\u003c\/li\u003e\n\u003cli\u003eBlack finish for a factory-style appearance\u003c\/li\u003e\n\u003cli\u003eMetal male and female end fittings with inverted flare ends\u003c\/li\u003e\n\u003cli\u003eEnd threads: M10-1.25 on both sides\u003c\/li\u003e\n\u003cli\u003eGasket or seal included\u003c\/li\u003e\n\u003cli\u003eDirect-fit application coverage for Mazda 626 and Mazda RX-7\u003c\/li\u003e\n\u003cli\u003eCentric part number 150.45310\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eCentric 150.45310 is a clutch hydraulic hose engineered for specific Mazda applications, including 1986-1987 Mazda 626 and 1981-1985 Mazda RX-7 rear upper positions. The hose measures 248.00 overall length and uses metal fittings with inverted flare connections, making it a practical replacement for worn or damaged hydraulic lines in the clutch system. This part cross-references Dorman - First Stop H38233 for the same application.\u003c\/p\u003e\u003cp\u003eAs part of the Centric Premium Brake Hydraulic Hoses line, this component reflects Centric’s focus on complete hydraulic coverage for brake and clutch service. If you are searching for a Mazda RX-7 rear upper clutch hydraulic hose or a Centric 150.45310 replacement hose for a Mazda 626, this part matches the listed vehicle applications and connection specifications.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eHydraulic fluid leakage at the clutch line\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose wear\u003c\/li\u003e\n\u003cli\u003eCorrosion or damage at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch circuit\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and position before ordering. This hose uses M10-1.25 threads, inverted flare ends, and a male-to-female fitting layout, so matching the original connection style is important for proper installation. Inspect the mating hard lines, seals, and mounting points before service, and replace any worn sealing surfaces to help ensure a secure hydraulic connection.\u003c\/p\u003e\u003cp\u003eFitment includes 1986-1987 Mazda 626, N\/A; 1984-1985 Mazda RX-7, Rear Upper, 13B Eng; 1984-1985 Mazda RX-7, Rear Upper, 12A Eng; and 1981-1983 Mazda RX-7, Rear Upper. Part number 150.45310 is listed for these applications and should be matched to the vehicle’s original hose routing and connection details.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is built around broad hydraulic coverage and application-specific replacement parts for brake and clutch service. The Centric Premium Brake Hydraulic Hoses line is DOT approved and uses materials and fittings selected for direct replacement use in the listed Mazda applications.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646623088821,"sku":"BKNJ-150.45310","price":22.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15045310_Fro.jpg?v=1774988900"},{"product_id":"centric-150-46024-clutch-hydraulic-hose","title":"Centric 150.46024 Clutch Hydraulic Hose - Rear Lower or Rear Upper","description":"\u003ch2\u003eCentric Premium Brake Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eThe Centric Premium Brake Hydraulic Hoses line delivers a direct-fit hydraulic hose solution for brake and clutch applications where reliable fluid transfer and secure end connections matter. Part number 150.46024 is a DOT approved hose with EPDM rubber outer sleeve construction, metal fittings, and inverted flare ends for a factory-style connection.\u003c\/p\u003e\u003cp\u003eCompatible With select Mitsubishi Diamante, Eclipse, Galant, Mirage, Expo, and 3000GT applications, plus Dodge Stealth, Plymouth Laser, Dodge Colt, Suzuki Forenza, and related interchange references. This Centric 150.46024 hose is built for rear lower and rear upper positions where specified in the fitment data.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDOT approved brake hydraulic hose construction\u003c\/li\u003e\n\u003cli\u003eBlack EPDM rubber outer sleeve for durable fluid-line service\u003c\/li\u003e\n\u003cli\u003eMetal male and female end fittings with inverted flare design\u003c\/li\u003e\n\u003cli\u003eM10-1.00 thread size at both ends\u003c\/li\u003e\n\u003cli\u003eBanjo bolt and clip provisions noted in the product data\u003c\/li\u003e\n\u003cli\u003eCentric Premium Brake Hydraulic Hoses product line coverage for hydraulic brake service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric 150.46024 is part of the Centric Premium Brake Hydraulic Hoses program, a hydraulic component range that also covers master cylinders, wheel cylinders, repair kits, and remanufactured power boosters. For buyers searching for a brake hose for Mitsubishi Eclipse rear lower, Mitsubishi Diamante rear upper, or Dodge Stealth rear lower applications, this hose provides the fitment-specific construction needed for hydraulic line replacement. The hose measures 10.118 inches overall length and uses metal fittings with inverted flare ends to match the listed vehicle applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - First Stop H38979 and Raybestos Brakes BH38979 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a cracked or leaking brake hydraulic hose\u003c\/li\u003e\n\u003cli\u003eRestoring firm hydraulic pressure at the rear brake circuit\u003c\/li\u003e\n\u003cli\u003eCorrecting fluid seepage at worn hose ends or fittings\u003c\/li\u003e\n\u003cli\u003eAddressing soft pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eRepairing a damaged hose on Mitsubishi, Dodge, Plymouth, or Suzuki fitments listed below\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle position before ordering, since fitment includes rear lower, rear upper, and N\/A listings depending on year and model. Confirm M10-1.00 thread size, inverted flare end style, and overall hose length against the original part before installation. Use the correct banjo bolt and washer specification referenced in the product data, and inspect adjacent hard lines, clips, and mounting points for corrosion or wear during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric’s brake hydraulic program is organized as a broad OE-style replacement catalog for brake fluid transfer components, with coverage that spans hoses, cylinders, repair kits, and boosters. Part number 150.46024 is DOT approved and built to match the listed hydraulic hose applications.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2004-2008 Suzuki Forenza, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1991-1999 Mitsubishi 3000GT, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1991-1996 Dodge Stealth, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1995-1996 Mitsubishi Diamante, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mitsubishi Diamante, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1994 Mitsubishi Diamante, Rear Upper\u003c\/li\u003e\n\u003cli\u003eFits 1994 Mitsubishi Diamante, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992-1994 Mitsubishi Expo, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992-1994 Mitsubishi Expo LRV, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1990-1994 Plymouth Laser, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mitsubishi Diamante, Rear Upper\u003c\/li\u003e\n\u003cli\u003eFits 1991-1993 Mitsubishi Eclipse, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992 Mitsubishi Galant, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1992 Mitsubishi Mirage, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1991 Mitsubishi Eclipse, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1989-1991 Mitsubishi Galant, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1991 Mitsubishi Mirage, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1989-1990 Dodge Colt, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1990 Mitsubishi Eclipse, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1989 Mitsubishi Mirage, Rear Lower\u003c\/li\u003e\n\u003cli\u003eFits 1988 Dodge Colt, Rear Lower\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43646632394933,"sku":"BKNJ-150.46024","price":13.81,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15046024_Fro_4b1b16a0-5851-458b-a3fa-bb252e87b5ac.jpg?v=1774988913"},{"product_id":"centric-151-42026-clutch-hydraulic-hose","title":"Centric 151.42026 Clutch Hydraulic Hose","description":"\u003ch2\u003eCentric Premium Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eCentric Premium Clutch Hydraulic Hose 151.42026 is a direct-fit hydraulic hose for select Nissan and INFINITI manual transmission applications. It supports clutch hydraulic fluid transfer for consistent pedal response in vehicles such as the Nissan 350Z and INFINITI G35.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCentric Premium Clutch Hydraulic Hoses product line\u003c\/li\u003e\n\u003cli\u003ePre-filled clutch hydraulic hose assembly for select passenger cars\u003c\/li\u003e\n\u003cli\u003eApplication-specific fitment for manual transmission clutch hydraulic systems\u003c\/li\u003e\n\u003cli\u003eCross-reference part numbers: 30855AC70A and 30855CD002\u003c\/li\u003e\n\u003cli\u003ePart number 151.42026 for catalog and fitment lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eCentric 151.42026 is part of the Centric Premium Clutch Hydraulic Hoses line, a range focused on pre-filled clutch hydraulics for popular passenger cars. This hose is listed for 2003-2007 INFINITI G35 and 2003-2006 Nissan 350Z applications, including 2006 Nissan 350Z built to 11\/06. For buyers searching for a clutch hydraulic hose for Nissan 350Z or INFINITI G35 manual transmission service, 151.42026 provides a cataloged OE-style replacement path.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic fluid transfer issues\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel\u003c\/li\u003e\n\u003cli\u003eLeaks in the clutch hydraulic hose circuit\u003c\/li\u003e\n\u003cli\u003eService replacement for worn hydraulic hose assemblies\u003c\/li\u003e\n\u003cli\u003eFitment-specific replacement needs for Nissan 350Z and INFINITI G35\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, model, and build date before ordering. Confirm the application against the listed fitment for 2003-2007 INFINITI G35 and 2003-2006 Nissan 350Z, including the 2006 350Z to 11\/06 note. Follow factory service procedures for clutch hydraulic system service and bleed the system after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric Parts supplies pre-filled clutch hydraulics for popular passenger cars through the Premium Clutch Hydraulic Hoses line. Part number 151.42026 is cataloged for direct application matching and OE cross-reference use.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43654489866421,"sku":"BKNJ-151.42026","price":21.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15142026_Fro.jpg?v=1774989425"},{"product_id":"centric-151-51002-clutch-hydraulic-hose","title":"Centric 151.51002 Clutch Hydraulic Hose","description":"\u003ch2\u003eCentric Premium Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eCentric Premium Clutch Hydraulic Hose 151.51002 is a direct-fit hydraulic hose for select Hyundai and Kia manual transmission applications. It is built for drivers replacing a worn or leaking clutch hydraulic line on vehicles such as the Hyundai Elantra, Hyundai Tiburon, Kia Spectra, and Kia Spectra5.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCentric Premium Clutch Hydraulic Hoses product line for manual clutch hydraulic service\u003c\/li\u003e\n\u003cli\u003ePre-filled clutch hydraulics for most popular passenger cars, as described by the manufacturer\u003c\/li\u003e\n\u003cli\u003eDirect replacement part for select Hyundai Elantra, Hyundai Tiburon, Kia Spectra, and Kia Spectra5 applications\u003c\/li\u003e\n\u003cli\u003ePart number 151.51002 for catalog and fitment verification\u003c\/li\u003e\n\u003cli\u003eCross-reference: Hyundai\/Kia OE part 416402D000 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Centric clutch hydraulic hose is part of the Centric Premium Clutch Hydraulic Hoses line, a range focused on pre-filled clutch hydraulic service for common passenger-car applications. Part number 151.51002 is listed for 2001-2006 Hyundai Elantra, 2003-2008 Hyundai Tiburon, 2004-2009 Kia Spectra, and 2005-2008 Kia Spectra5. If you are searching for a clutch hydraulic hose for Hyundai Elantra or a clutch hydraulic hose for Kia Spectra, this part number provides a cataloged replacement option for those manual transmission vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic fluid leakage at the hose assembly\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by a failing hydraulic line\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch release system\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged or deteriorated clutch hose\u003c\/li\u003e\n\u003cli\u003eFitment-specific replacement needs on Hyundai Elantra, Hyundai Tiburon, Kia Spectra, and Kia Spectra5\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, and model against the listed fitment before ordering. Confirm the OE cross-reference 416402D000 and compare the existing hose routing and connection points to the original part. After installation, bleed the clutch hydraulic system according to the vehicle service procedure to restore proper pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric Parts supplies pre-filled clutch hydraulics for popular passenger-car applications, and this part is cataloged under the Centric Premium Clutch Hydraulic Hoses line for application-specific replacement use.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43654503366837,"sku":"BKNJ-151.51002","price":24.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15151002_Fro.jpg?v=1774989430"},{"product_id":"centric-151-51011-clutch-hydraulic-hose","title":"Centric 151.51011 Clutch Hydraulic Hose","description":"\u003ch2\u003eCentric Premium Clutch Hydraulic Hose for Hyundai Elantra\u003c\/h2\u003e\u003cp\u003eCentric Premium Clutch Hydraulic Hose 151.51011 is a direct-fit hydraulic hose for select Hyundai Elantra applications. It supports clutch hydraulic fluid transfer for 2008-2009 Hyundai Elantra models and is part of the Centric Premium Clutch Hydraulic Hoses line.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2008-2009 Hyundai Elantra, N\/A\u003c\/li\u003e\n\u003cli\u003eCentric Premium Clutch Hydraulic Hoses product line\u003c\/li\u003e\n\u003cli\u003ePre-filled clutch hydraulics available for popular passenger car applications\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for clutch hydraulic hose service\u003c\/li\u003e\n\u003cli\u003ePart number 151.51011 for application matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eCentric Parts markets this hose within its Premium Clutch Hydraulic Hoses line for passenger car clutch service. For Hyundai Elantra owners needing a replacement clutch hydraulic hose, 151.51011 provides a fitment-specific solution for 2008-2009 models. This part cross-references Hyundai OE number 416402H010 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch hydraulic fluid leakage from a worn hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic line wear\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged or deteriorated clutch hose\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year and application before ordering. Match the hose to the existing clutch hydraulic routing on the 2008-2009 Hyundai Elantra and inspect the surrounding hydraulic components for wear or contamination during service. Bleeding the clutch hydraulic system after installation is typically required to restore proper pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCentric Parts positions this hose within its Premium Clutch Hydraulic Hoses line for popular passenger car coverage, with application-specific fitment for the Hyundai Elantra.\u003c\/p\u003e","brand":"Centric","offers":[{"title":"Default Title","offer_id":43654503858357,"sku":"BKNJ-151.51011","price":17.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/CE_15151011_Fro.jpg?v=1774989430"},{"product_id":"dorman-h36742-clutch-hydraulic-hose","title":"Dorman H36742 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H36742 Brake Hydraulic Hose Overview\u003c\/h2\u003e\u003cp\u003eDorman H36742 is a flexible brake hydraulic hose engineered to match the fit, function, and performance of the original hose on specific Toyota applications. Built with EPDM rubber and treated steel end fittings, it supports reliable brake fluid transfer for rear and front brake positions on select Toyota Van, Land Cruiser, Celica, and Corona models.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a Toyota brake hydraulic hose, Toyota Van rear brake hose, or Toyota Corona front brake hose, this Dorman H36742 replacement is built around OE-style dimensions and connection points for the listed applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose construction with black EPDM rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel male and female end fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eOverall length: 14.44 in.\u003c\/li\u003e\n\u003cli\u003e10 mm end 1 thread diameter with M10 x 1.0 end 2 fitting inside diameter\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Toyota brake hose applications\u003c\/li\u003e\n\u003cli\u003eCompatible with rear left, rear right, rear center, front left, and front right positions depending on vehicle\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman H36742 is a brake hydraulic hose designed for specific Toyota brake systems where a flexible line is required between hard brake tubing and the caliper or wheel-end connection. The hose uses EPDM rubber for the hose material and treated steel fittings at both ends to support a secure, OE-style connection. This part number is also referenced as Dorman H36742 and cross-references Raybestos Brakes BH36742 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1987-1989 Toyota Van, rear left and rear right; 1985 Toyota Land Cruiser, rear center to 4\/85; 1981-1984 Toyota Land Cruiser, rear center; 1981-1983 Toyota Celica, N\/A; and 1974-1978 Toyota Corona, front left and front right. These fitments make it a practical choice when replacing a worn Toyota brake hose on the listed vehicles and positions.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part May Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCracked or weathered brake hose rubber\u003c\/li\u003e\n\u003cli\u003eBrake fluid seepage at the hose connection\u003c\/li\u003e\n\u003cli\u003eRestricted brake fluid flow from an aged flexible line\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent brake pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the original hose fittings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and brake position before ordering, since fitment varies by Toyota application and location. Compare the original hose length, fitting style, and thread size to the existing part before installation. Because mounting hardware, brackets, and seals are not included, reuse or source the required related components as needed during the brake repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman engineers this brake hydraulic hose to match the original part’s fit, function, and performance on the listed vehicles. It is built for long-lasting durability as part of a complete brake repair on select Toyota applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774636097717,"sku":"BKKX-H36742","price":26.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H36742_Fro.jpg?v=1774995965"},{"product_id":"dorman-h36937-clutch-hydraulic-hose","title":"Dorman H36937 Clutch Hydraulic Hose - Front Left Center, Front Right Center, Rear Left Outer or Rear Right Outer","description":"\u003ch2\u003eDorman H36937 Brake Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H36937 is a flexible brake hydraulic hose engineered to match the fit, function, and performance of the original hose on specific Toyota applications. It uses EPDM rubber construction with treated steel male and female fittings for a direct replacement on select Corolla, Celica, and Land Cruiser positions.\u003c\/p\u003e\u003cp\u003eFor Toyota Corolla brake hose replacement, Toyota Celica rear brake hose service, or Toyota Land Cruiser front brake hose repair, this hose is built to follow OE-style dimensions and connection points. The black rubber outer sleeve and 10.13-inch overall length support a clean, vehicle-specific installation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible brake hydraulic hose for select Toyota vehicles\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material with black outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel end fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eMale 10 mm end 1 thread diameter and female M10 x 1.0 end 2 fitting\u003c\/li\u003e\n\u003cli\u003eOE-style fit, function, and performance for specific positions\u003c\/li\u003e\n\u003cli\u003eCompatible with Corolla, Celica, and Land Cruiser brake hose applications\u003c\/li\u003e\n\u003cli\u003eDorman H36937 cross-references Raybestos Brakes BH36937 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman brake hydraulic hose is built for direct replacement use on confirmed Toyota fitments, including 1975-1977 Toyota Corolla, 1978 Toyota Corolla to 4\/78, 1983-1987 Toyota Corolla, 1979-1985 Toyota Celica rear left outer and rear right outer positions, and 1976-1980 and 1982-1984 Toyota Land Cruiser front left center and front right center positions. The hose is also listed for 1985-1987 Toyota Corolla rear left outer and rear right outer positions. Dorman H36937 is intended to restore proper hydraulic routing and connection integrity where the original hose has aged, cracked, or leaked.\u003c\/p\u003e\u003cp\u003eThe EPDM rubber hose material is selected for brake system use, while the treated steel fittings help maintain a dependable connection at the vehicle hard line and caliper or wheel-end interface. If you are searching for a Toyota Corolla brake hydraulic hose, Toyota Celica rear brake hose, or Toyota Land Cruiser front brake hose by part number H36937, this replacement follows the specified OE-style configuration.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrake fluid seepage from a worn or damaged hose\u003c\/li\u003e\n\u003cli\u003eCracking, swelling, or hardening of the original rubber hose\u003c\/li\u003e\n\u003cli\u003eRestricted brake fluid flow caused by internal hose deterioration\u003c\/li\u003e\n\u003cli\u003eCorrosion or fitment issues at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eLoss of proper hydraulic connection at the listed Toyota positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and brake position before ordering, since fitment varies by Corolla, Celica, and Land Cruiser application. Confirm the end fitting style, thread size, and overall length against the original hose before installation. Inspect adjacent brake lines, clips, and mounting points for wear or corrosion during service, and bleed the brake system after replacement according to factory procedure.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman H36937 is engineered to match the original hose’s fit, function, and performance on the listed vehicles and positions. It is built as a direct replacement brake hydraulic hose for specific Toyota applications and is backed by Dorman’s OE-style replacement approach.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774666965173,"sku":"BKKX-H36937","price":22.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H36937_Fro.jpg?v=1774995979"},{"product_id":"dorman-h36966-clutch-hydraulic-hose","title":"Dorman H36966 Clutch Hydraulic Hose","description":"\u003ch2\u003eClutch Hydraulic Hose for Toyota Applications\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is a direct replacement for select Toyota vehicles that need a dependable hydraulic line for clutch operation. Built with EPDM rubber and treated steel female M10 x 1.0 fittings, Part Number H36966 is made to match the original hose layout on supported applications.\u003c\/p\u003e\u003cp\u003eUse this replacement hose when servicing a leaking or cracked clutch hydraulic line on Toyota Pickup, 4Runner, T100, and Celica applications. The hose is engineered for a precise OE-style fit to support a complete clutch repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Dorman\u003c\/li\u003e\n\u003cli\u003ePart Number: H36966\u003c\/li\u003e\n\u003cli\u003eClutch hydraulic hose for select Toyota vehicles\u003c\/li\u003e\n\u003cli\u003eEPDM rubber construction with rubber jacket\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings, M10 x 1.0 on both ends\u003c\/li\u003e\n\u003cli\u003eLength: 14.38\u003c\/li\u003e\n\u003cli\u003eReplacement hose for front and rear listed positions where applicable\u003c\/li\u003e\n\u003cli\u003eThis part cross-references Dorman - HELP 77112 for the same application.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman H36966 is a replacement clutch hydraulic hose designed for specific Toyota models from 1975 through 1998. It is built to match the original hose configuration on supported vehicles, helping restore hydraulic connection integrity after hose wear, cracking, or leakage. Fitment includes Toyota Pickup front left and front right applications across multiple year ranges, Toyota 4Runner front left and front right applications, Toyota T100 front left and front right applications, and select Toyota Celica and Corolla positions. For buyers searching for a Toyota Pickup clutch hydraulic hose, Toyota 4Runner hydraulic hose, or Toyota Celica clutch line replacement, this part number H36966 provides a vehicle-specific option.\u003c\/p\u003e\u003ch2\u003eWhat It Can Help Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible fluid leakage from a cracked clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eHydraulic line damage from age, heat, or road exposure\u003c\/li\u003e\n\u003cli\u003eLoss of clutch hydraulic pressure at the slave cylinder circuit\u003c\/li\u003e\n\u003cli\u003eReplacement needs during clutch system service on Toyota Pickup, 4Runner, T100, or Celica models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle year, model, and position before ordering, since fitment varies by front left, front right, inner front, rear left, and rear right applications. Verify the M10 x 1.0 female fittings and hose length against the original part before installation. Inspect adjacent clutch hydraulic components for wear, corrosion, or fluid contamination while the system is open.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this hose as a precision-engineered replacement for the original clutch hose on listed vehicles. The design focuses on OE-style fit and function for a reliable clutch repair on supported Toyota applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774678859957,"sku":"BKKX-H36966","price":24.8,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H36966_Fro.jpg?v=1774995982"},{"product_id":"dorman-h38110-clutch-hydraulic-hose","title":"Dorman H38110 Clutch Hydraulic Hose - Rear Left Outer or Rear Right Outer","description":"\u003ch2\u003eDorman H38110 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38110 is a replacement clutch hydraulic hose engineered to match the original hose design on specific vehicles. It is built with EPDM rubber and treated steel fittings to support a reliable clutch hydraulic repair on Toyota Cressida, Toyota Corona, and Toyota Celica applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber hose construction for hydraulic service\u003c\/li\u003e\n\u003cli\u003eLength: 8.38 in.\u003c\/li\u003e\n\u003cli\u003eMale M10 x 1.0 end and female 3\/8 in-24 end\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material on both ends\u003c\/li\u003e\n\u003cli\u003eRubber jacket material\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required and no mounting hardware included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose, part number H38110, is a direct replacement-style component for select Toyota rear brake and clutch hydraulic applications listed by fitment. It is precision-engineered to match the original hose configuration, helping restore proper hydraulic routing and connection points on 1978-1981 Toyota Celica, 1979-1982 Toyota Corona, and 1983-1988 Toyota Cressida rear left outer or rear right outer positions. This part cross-references Four Seasons 77499 and Centric Parts 150.44316 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaking hydraulic fluid at the hose body or fittings\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eDamaged threaded connections at the clutch hydraulic line\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure caused by hose failure\u003c\/li\u003e\n\u003cli\u003eRestoration of proper clutch pedal hydraulic response after hose replacement\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the end fittings, length, and vehicle position before installation. This hose uses a male M10 x 1.0 fitting on one end and a female 3\/8 in-24 fitting on the other, so matching the original connection style is important for a proper seal and routing. Inspect adjoining hydraulic components for wear or contamination before completing the repair on Toyota Cressida, Toyota Corona, or Toyota Celica applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle specifications for listed applications. H38110 is built for the confirmed fitment shown above and uses treated steel fittings with EPDM rubber construction for service in hydraulic systems.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774716379317,"sku":"BKKX-H38110","price":26.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38110_Fro.jpg?v=1774995998"},{"product_id":"dorman-h38111-clutch-hydraulic-hose","title":"Dorman H38111 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38111 Brake Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38111 is a flexible brake hydraulic hose engineered to match the fit, function, and performance of the original hose on specific Toyota applications. It uses an EPDM rubber hose body with treated steel female fittings and a black outer sleeve for a direct replacement on select Toyota T100 and Toyota Tercel models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose construction for brake hydraulic routing\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material with a protective jacket\u003c\/li\u003e\n\u003cli\u003eBlack outer sleeve for OE-style appearance\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 10.13 in.\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select rear left and rear right positions\u003c\/li\u003e\n\u003cli\u003ePart number H38111 for catalog and service matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis brake hydraulic hose is built for specific Toyota brake repair applications where the original hose needs to be replaced with a part that matches the factory layout and connection style. The treated steel female fittings, M10 x 1.0 connection, and flexible EPDM rubber construction support proper routing and secure attachment in the brake system. Dorman H38111 is listed for 1993-1994 Toyota T100 and for 1980-1982 and 1987-1990 Toyota Tercel in rear left and rear right positions. This part cross-references Raybestos Brakes BH38111 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1993-1994 Toyota T100, N\/A.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1990 Toyota Tercel, rear left.\u003c\/li\u003e\n\u003cli\u003eFits 1980-1982 Toyota Tercel, rear left.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1990 Toyota Tercel, rear right.\u003c\/li\u003e\n\u003cli\u003eFits 1980-1982 Toyota Tercel, rear right.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrake fluid leaks from a worn or damaged hydraulic hose\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eRestricted brake fluid flow caused by internal hose wear\u003c\/li\u003e\n\u003cli\u003eIncorrect hose length or fitting style during brake repair\u003c\/li\u003e\n\u003cli\u003eRear brake line replacement on select Toyota T100 and Toyota Tercel models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and brake hose position before installation. Confirm the female fitting style, M10 x 1.0 thread size, and overall hose length against the removed part to ensure proper routing and connection. Inspect adjacent brake components, brackets, and seals during service, since mounting hardware, brackets, and seals are not included.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this hose to match original equipment fit and function for the listed Toyota applications. The part number H38111 is intended for direct replacement use in brake system service where the factory hose configuration is required.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774718673077,"sku":"BKKX-H38111","price":29.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38111_Fro.jpg?v=1774995998"},{"product_id":"dorman-h38113-clutch-hydraulic-hose","title":"Dorman H38113 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38113 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is a direct replacement for the original hose used on select Toyota Pickup and Toyota 4Runner applications. Built with EPDM rubber and treated steel female M10 x 1.0 fittings, H38113 is made for a precise OE-style repair when the factory hose is leaking, cracked, or worn.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement clutch hydraulic hose for select Toyota vehicles\u003c\/li\u003e\n\u003cli\u003eEPDM rubber flexible hose construction\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for durability\u003c\/li\u003e\n\u003cli\u003e10.38-inch hose length\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman H38113 is engineered to match the original clutch hose layout on specific Toyota Pickup and Toyota 4Runner models, helping restore hydraulic clutch function with the correct hose length and fitting style. The flexible EPDM rubber body is paired with treated steel female M10 x 1.0 ends for a secure connection in the clutch hydraulic system. This part cross-references Sunsong 2203633 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1975-1978 Toyota Pickup, 1\/2 Ton; 1979-1983 Toyota Pickup, 1\/2 Ton and 3\/4 Ton; 1984 Toyota Pickup, 3\/4 Ton; 1984-1988 Toyota Pickup, 1\/2 Ton; 1984-1986 Toyota 4Runner; and 1992-1995 Toyota Pickup. The Dorman H38113 part number is also a useful reference when verifying the correct clutch hydraulic hose for these Toyota applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch fluid leaks from a cracked or deteriorated hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eVisible hose swelling, splitting, or dry rot\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eService issues from an incorrect hose length or fitting type\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle year, model, and clutch hose fitting style before installation. Match the female M10 x 1.0 ends and verify the 10.38-inch length against the original hose routing on your Toyota Pickup or Toyota 4Runner. Inspect the surrounding hydraulic components for leaks or wear before bleeding the clutch system after replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original equipment form and function on specific vehicles, supporting a reliable clutch repair with the correct hose design and materials. H38113 is built as a direct-fit replacement for the listed Toyota applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774719295669,"sku":"BKKX-H38113","price":25.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38113_Fro.jpg?v=1774995999"},{"product_id":"dorman-h38117-clutch-hydraulic-hose","title":"Dorman H38117 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38117 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38117 is a replacement clutch hydraulic hose for specific Nissan applications, including Nissan Pathfinder and Nissan 720 fitments. It is built to match the original hose layout and connection style for a direct repair on vehicles with a leaking or cracked clutch hydraulic line.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber construction with a rubber jacket for hydraulic service\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eMale M10 x 1.0 end and female M10 x 1.0 end\u003c\/li\u003e\n\u003cli\u003eLength: 10.63 in.\u003c\/li\u003e\n\u003cli\u003eReplacement hose for clutch hydraulic repair on select Nissan Pathfinder and Nissan 720 models\u003c\/li\u003e\n\u003cli\u003eDorman part number H38117 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis clutch hydraulic hose is engineered as a direct replacement for the original hose used on select Nissan vehicles. The EPDM rubber hose material is paired with treated steel fittings to support dependable hydraulic routing and connection integrity. For buyers searching for a Nissan Pathfinder clutch hydraulic hose or a Nissan 720 hydraulic hose replacement, Dorman H38117 provides the correct style of service part for the listed applications. This part cross-references Raybestos Brakes (e.g., BH38117) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Repair\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFluid leakage from a cracked or deteriorated clutch hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eVisible hose swelling, splitting, or dry rot\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eService replacement for worn original clutch hydraulic lines\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify end style, thread size, and hose length before installation. This hose uses a male M10 x 1.0 fitting on one end and a female M10 x 1.0 fitting on the other, so the vehicle’s original connection points should be matched carefully. Inspect the surrounding clutch hydraulic components for contamination, corrosion, or damage before completing the repair. Confirm fitment for your exact year and position: Fits 1988-1995 Nissan Pathfinder, Rear Left; Fits 1988-1995 Nissan Pathfinder, Rear Right; Fits 1980-1986 Nissan 720, N\/A.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original equipment form and function for specific vehicle applications. H38117 is built for the listed Nissan Pathfinder and Nissan 720 fitments and is intended to support a complete clutch hydraulic repair using the correct hose configuration.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774720540853,"sku":"BKKX-H38117","price":27.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38117_Fro.jpg?v=1774995999"},{"product_id":"dorman-h38228-clutch-hydraulic-hose","title":"Dorman H38228 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38228 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic line with a direct-fit hose engineered for specific Toyota applications. Dorman H38228 is built to match the original hose layout for a reliable clutch repair on Toyota 4Runner and Toyota Pickup models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible EPDM rubber construction for clutch hydraulic service\u003c\/li\u003e\n\u003cli\u003eLength: 9.63 in.\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for the hose ends\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required for installation\u003c\/li\u003e\n\u003cli\u003eDirect replacement for specific Toyota clutch hydraulic hose applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is made to restore hydraulic fluid transfer in the clutch system on select Toyota trucks and SUVs. The flexible hose design and OE-style female M10 x 1.0 end fittings support a proper connection at the factory mounting points. Part number H38228 is a practical replacement when the original hose shows cracking, seepage, or age-related wear. This part cross-references Centric Parts 150.44306 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1986-1995 Toyota 4Runner, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1992-1995 Toyota Pickup, N\/A, 1\/2 Ton\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Toyota Pickup, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch pedal feels soft or inconsistent\u003c\/li\u003e\n\u003cli\u003eVisible hydraulic fluid leakage at the hose\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or deteriorated hose material\u003c\/li\u003e\n\u003cli\u003eDifficulty disengaging the clutch\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the hose length, fitting type, and vehicle application before installation. Inspect the surrounding clutch hydraulic components for wear, contamination, or fluid loss, and replace any damaged parts as needed. Bleed the clutch hydraulic system after installation to remove air and restore proper pedal feel. Fits 1986-1995 Toyota 4Runner and 1986-1995 Toyota Pickup applications listed above, including 1\/2 Ton Pickup coverage where specified.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original equipment form and function for specific vehicle applications. H38228 is engineered as a direct replacement hose for the listed Toyota fitments, with treated steel fittings and EPDM rubber construction selected for clutch hydraulic service.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774760485045,"sku":"BKKX-H38228","price":27.53,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38228_Fro.jpg?v=1774996017"},{"product_id":"dorman-h38233-clutch-hydraulic-hose","title":"Dorman H38233 Clutch Hydraulic Hose - Rear Left Upper or Rear Right Upper","description":"\u003ch2\u003eDorman H38233 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38233 is a flexible clutch hydraulic hose built for specific Mazda applications, including 1986-1987 Mazda 626 and 1981-1985 Mazda RX-7 rear upper positions. It uses an EPDM rubber hose body with treated steel male and female ends for a direct-fit replacement in clutch hydraulic routing.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose construction for clutch hydraulic service\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material with black outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel end fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eMale 10 mm end and female M10 x 1.0 end configuration\u003c\/li\u003e\n\u003cli\u003eOverall length: 9.88 in.\u003c\/li\u003e\n\u003cli\u003eDirect replacement for Mazda 626 and Mazda RX-7 applications listed below\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is engineered to match the fit and function of the original hose used on select Mazda vehicles. The hose design uses rubber construction for flexibility, while the treated steel fittings help maintain a stable connection at the hydraulic line ends. Dorman H38233 cross-references Raybestos Brakes BH38233 and Centric Parts 150.45310 for the same application. It is a practical replacement for Mazda 626 and Mazda RX-7 clutch hydraulic routing where the original hose has aged, cracked, or lost sealing performance.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1986-1987 Mazda 626, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1981-1985 Mazda RX-7, Rear Left Upper\u003c\/li\u003e\n\u003cli\u003eFits 1981-1985 Mazda RX-7, Rear Right Upper\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores clutch hydraulic line integrity after hose wear or cracking\u003c\/li\u003e\n\u003cli\u003eAddresses fluid leakage at the hose ends\u003c\/li\u003e\n\u003cli\u003eReplaces a damaged or corroded original hose on Mazda 626 and Mazda RX-7\u003c\/li\u003e\n\u003cli\u003eHelps correct soft or inconsistent hydraulic line response caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eSupports repair of a leaking or failed flexible hydraulic connection\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify end style, thread size, and routing before installation. This hose does not include mounting hardware, brackets, gaskets, or seals, so reuse or source any required related components separately. Inspect the surrounding hydraulic system for corrosion, damaged hard lines, or fluid contamination before completing the repair. After installation, bleed the hydraulic system according to the vehicle service procedure.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this hose to match original fit, function, and performance on the listed Mazda applications. The part number is H38233.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43774761795765,"sku":"BKKX-H38233","price":28.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38233_Fro.jpg?v=1774996017"},{"product_id":"dorman-h38275-clutch-hydraulic-hose","title":"Dorman H38275 Clutch Hydraulic Hose","description":"\u003ch2\u003eOE-Style Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38275 is a flexible clutch hydraulic hose built to match the original fit, function, and performance on specific vehicles and positions. It uses an EPDM rubber hose with treated steel female fittings and a black steel outer sleeve for a direct replacement on select Mitsubishi, Dodge, Hyundai, Plymouth, and Toyota applications.\u003c\/p\u003e\u003cp\u003eCompatible With front left inner and front right inner positions on vehicles such as the Mitsubishi 3000GT, Dodge Stealth, and Mitsubishi Eclipse, this Dorman H38275 hose is engineered for accurate routing and dependable hydraulic transfer. It also cross-references Beck\/Arnley 073-1000 for the same application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible clutch hydraulic hose for select OE-style brake and clutch hydraulic applications\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose construction with a steel outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 12.63 in.\u003c\/li\u003e\n\u003cli\u003eBlack finish for a factory-style appearance\u003c\/li\u003e\n\u003cli\u003eJacket included for added hose protection\u003c\/li\u003e\n\u003cli\u003eDorman H38275 replacement for specific front and rear positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis hydraulic hose is precision-engineered to match the original part’s fit and function on supported vehicles, helping maintain proper hydraulic line routing and connection integrity. It is listed for a wide range of applications, including 1991-1999 Mitsubishi 3000GT front left inner and front right inner, 1991-1996 Dodge Stealth front left inner and front right inner, 1990-1994 Mitsubishi Eclipse front left inner and front right inner, and 1985-1993 Mitsubishi Galant front left inner and front right inner. The Dorman H38275 also covers additional positions on Mitsubishi Mirage, Hyundai Sonata, Hyundai Excel, Dodge Colt, and other listed models.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a leaking or damaged clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eRestoring hydraulic pressure transfer in the clutch system\u003c\/li\u003e\n\u003cli\u003eCorrecting cracked, corroded, or worn hose sections\u003c\/li\u003e\n\u003cli\u003eAddressing soft pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eRepairing OE-style line routing on supported Mitsubishi, Dodge, and Hyundai vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and position before installation. This hose uses female end fittings with 10 mm thread diameter and M10 x 1.0 connection sizing. Mounting hardware, brackets, and seals are not included, so reuse or source the required components as needed. Confirm routing clearance and inspect adjoining hydraulic components before completing the repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this hose to match original equipment fit and performance expectations for the listed applications. Part number H38275 is built for direct replacement use on confirmed vehicle positions and is supported by Dorman’s OE-style replacement engineering approach.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779776741557,"sku":"BKKX-H38275","price":22.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38275_Fro.jpg?v=1774996027"},{"product_id":"dorman-h38465-clutch-hydraulic-hose","title":"Dorman H38465 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38465 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38465 is a flexible clutch hydraulic hose built with an EPDM rubber hose body and treated steel female fittings for a direct-fit replacement on select Honda and Mitsubishi applications. It is engineered to match the original hose’s fit, function, and performance for dependable hydraulic transfer in the clutch system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose design for clutch hydraulic routing\u003c\/li\u003e\n\u003cli\u003eEPDM rubber outer hose material with black finish\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings on both ends\u003c\/li\u003e\n\u003cli\u003e10 mm end 1 thread diameter and M10 x 1.0 end 2 fitting inside diameter\u003c\/li\u003e\n\u003cli\u003eOverall length: 10.63 in.\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for select Honda Accord, Mitsubishi Eclipse, Mitsubishi Expo LRV, Mitsubishi Sigma, and Mitsubishi Galant applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is designed for vehicles that require a flexible hydraulic line with the correct end fittings and length for proper routing. The hose construction uses EPDM rubber for the hose material and treated steel for the female end fittings, helping maintain a secure connection in the clutch hydraulic circuit. Dorman H38465 is a practical replacement choice for 1976-1981 Honda Accord rear left and rear right positions, plus select Mitsubishi models including the 1986-1987 Galant, 1989-1990 Sigma, and 1992-1994 Eclipse and 1992-1993 Expo LRV. This part cross-references Raybestos Brakes BH38465 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1976-1979 Honda Accord, rear left.\u003c\/li\u003e\n\u003cli\u003eFits 1976-1979 Honda Accord, rear right.\u003c\/li\u003e\n\u003cli\u003eFits 1980-1981 Honda Accord, rear left. Notes: Nichirin and Toyoda hoses.\u003c\/li\u003e\n\u003cli\u003eFits 1980-1981 Honda Accord, rear right. Notes: Nichirin and Toyoda hoses.\u003c\/li\u003e\n\u003cli\u003eFits 1986 Mitsubishi Galant, N\/A. Notes: Fits from September 1986.\u003c\/li\u003e\n\u003cli\u003eFits 1987 Mitsubishi Galant, N\/A.\u003c\/li\u003e\n\u003cli\u003eFits 1989-1990 Mitsubishi Sigma, N\/A.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1994 Mitsubishi Eclipse, N\/A.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mitsubishi Expo LRV, N\/A.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify the vehicle position and hose routing before installation.\u003c\/li\u003e\n\u003cli\u003eConfirm the fitting thread size and end style match the original hose.\u003c\/li\u003e\n\u003cli\u003eInspect the surrounding hydraulic components for wear, leaks, or corrosion before replacing the hose.\u003c\/li\u003e\n\u003cli\u003eBracket, gasket or seal, and mounting hardware are not included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman engineers this hose to match original fit, function, and performance on the listed vehicles and positions. It is built as a replacement hydraulic hose for brake and clutch system service where the original line has aged, cracked, or begun to leak.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779809902773,"sku":"BKKX-H38465","price":26.4,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38465_Fro.jpg?v=1774996056"},{"product_id":"dorman-h38471-clutch-hydraulic-hose","title":"Dorman H38471 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38471 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eRestore clutch hydraulic performance with this Dorman replacement hose for specific Hyundai, Mitsubishi, and Honda applications. The H38471 is precision-engineered to match the original clutch hose layout on supported vehicles, helping complete a reliable clutch repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber construction for hydraulic hose service\u003c\/li\u003e\n\u003cli\u003e10.75-inch length\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for durability\u003c\/li\u003e\n\u003cli\u003eRubber jacket material\u003c\/li\u003e\n\u003cli\u003eNo bracket required for mounting\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select clutch hydraulic hose applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman H38471 is a clutch hydraulic hose built to match the original hose configuration on specific vehicles. It uses EPDM rubber with treated steel female M10 x 1.0 fittings at both ends, along with a rubber jacket for service in hydraulic clutch systems. This part cross-references Raybestos Brakes BH38464 for the same application. For buyers searching for a clutch hydraulic hose for 1990-1993 Hyundai Excel, 1990-1993 Mitsubishi Precis, or 1991-1992 Hyundai Scoupe, this replacement hose provides the correct fitment profile. It also applies to 1979-1982 Honda Prelude rear left and rear right positions. The Dorman H38471 part number is commonly used when replacing a leaking or cracked clutch hose during clutch system repair.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible fluid leakage from a cracked clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eDamage from age-related rubber wear or heat exposure\u003c\/li\u003e\n\u003cli\u003eService issues during clutch repair on supported Hyundai, Mitsubishi, and Honda models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the hose length, end fitting type, and vehicle position before installation. Confirm the application against the original hose routing on the vehicle, especially for 1979-1982 Honda Prelude rear left and rear right locations. Inspect adjoining hydraulic components for contamination or wear before completing the repair. Bleed the clutch hydraulic system after installation to restore proper pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this replacement hose to match the original clutch hose design on listed applications. The H38471 is built with EPDM rubber and treated steel fittings for a direct-fit repair on supported vehicles.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779809935541,"sku":"BKKX-H38471","price":27.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38471_Fro.jpg?v=1774996056"},{"product_id":"dorman-h38559-clutch-hydraulic-hose","title":"Dorman H38559 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38559 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eThe Dorman H38559 clutch hydraulic hose is a direct replacement for specific Chevrolet and GMC trucks and SUVs that need a dependable clutch hydraulic line repair. Built with EPDM rubber and treated steel male M12 x 1.0 fittings, it is engineered to match the original hose layout for a clean, OE-style service replacement.\u003c\/p\u003e\u003cp\u003eFor shoppers searching for a clutch hydraulic hose for a 1985-1991 Chevrolet C10, K5 Blazer, or GMC Jimmy, this replacement helps restore proper hydraulic connection at the clutch system. The Dorman H38559 is also a fitment-based solution for many C\/K and R\/V platform applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber flexible hose construction for clutch hydraulic service\u003c\/li\u003e\n\u003cli\u003eMale M12 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for added durability\u003c\/li\u003e\n\u003cli\u003eDirect replacement design for specific Chevrolet and GMC applications\u003c\/li\u003e\n\u003cli\u003eNo bracket required for installation on listed vehicles\u003c\/li\u003e\n\u003cli\u003eCross-references Raybestos Brakes BH38559 and Sunsong 2201300 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eThis clutch hydraulic hose is built to replace a leaking or cracked original hose on select Chevrolet and GMC trucks and SUVs from 1985-1991. The flexible hose design and OE-style dimensions help maintain the original routing and connection points, while the treated steel fittings provide a secure threaded interface at both ends. The Dorman H38559 is a practical choice when servicing clutch hydraulic lines on vehicles such as Chevrolet C10, K10, K5 Blazer, GMC C1500, and GMC Jimmy applications.\u003c\/p\u003e\u003cp\u003ePart number H38559 is also a useful search term for buyers comparing replacement clutch hoses by application. If you are replacing a worn clutch hydraulic hose on a Chevrolet or GMC manual-transmission vehicle, this part is built around the original vehicle fitment rather than a universal design.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFluid leakage from a cracked clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eVisible hose damage from age, heat, or road exposure\u003c\/li\u003e\n\u003cli\u003eService issues on original clutch line routing in select Chevrolet and GMC models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, and model against the listed fitment before ordering. This hose uses male M12 x 1.0 fittings at both ends and does not require a bracket on the listed applications. Inspect the surrounding clutch hydraulic components, including the master cylinder and slave cylinder connections, before installation to confirm the repair addresses the full leak source.\u003c\/p\u003e\u003cp\u003eCompatible With 1985-1991 Chevrolet C10, 1985-1986 Chevrolet C10 Suburban, 1985-1986 Chevrolet C20, 1985-1986 Chevrolet C20 Suburban, 1985-1986 Chevrolet C30, 1985-1986 Chevrolet K10, 1985-1986 Chevrolet K10 Suburban, 1985-1986 Chevrolet K20, 1985-1986 Chevrolet K20 Suburban, 1985-1986 Chevrolet K30, 1985-1986 Chevrolet K5 Blazer, 1987-1991 Chevrolet Blazer, 1987-1989 Chevrolet R2500, 1987-1988 Chevrolet R10, 1987-1988 Chevrolet R10 Suburban, 1987-1988 Chevrolet R20, 1987-1988 Chevrolet R20 Suburban, 1987-1988 Chevrolet R30, 1987-1988 Chevrolet V10, 1987-1988 Chevrolet V10 Suburban, 1987-1988 Chevrolet V20, 1987-1988 Chevrolet V20 Suburban, 1987-1988 Chevrolet V30, 1989-1991 Chevrolet R1500 Suburban, 1989-1991 Chevrolet R2500 Suburban, 1989-1991 Chevrolet R3500, 1989-1991 Chevrolet V1500 Suburban, 1989-1991 Chevrolet V2500 Suburban, 1989-1991 Chevrolet V3500, 1985-1986 GMC C1500, 1985-1986 GMC C1500 Suburban, 1985-1986 GMC C2500, 1985-1986 GMC C2500 Suburban, 1985-1986 GMC C3500, 1985-1986 GMC K1500, 1985-1986 GMC K1500 Suburban, 1985-1986 GMC K2500, 1985-1986 GMC K2500 Suburban, 1985-1986 GMC K3500, 1985-1991 GMC Jimmy, 1987 GMC R1500, 1987 GMC V1500, 1987 GMC V2500, 1987-1989 GMC R2500, 1987-1991 GMC R1500 Suburban, 1987-1991 GMC R2500 Suburban, 1987-1991 GMC R3500, 1987-1991 GMC V1500 Suburban, 1987-1991 GMC V2500 Suburban, 1987-1991 GMC V3500.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle applications, and this clutch hydraulic hose follows that OE-style approach for specific Chevrolet and GMC platforms. Part number H38559 is built for application-specific service where the original hose has failed or deteriorated.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779817013429,"sku":"BKKX-H38559","price":49.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38559_Fro_9f5b4d6f-f59d-4ddf-97e4-931ee8bf9dd8.jpg?v=1774996072"},{"product_id":"dorman-h38561-clutch-hydraulic-hose","title":"Dorman H38561 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38561 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic hose with a direct-fit solution built for specific Chevrolet and GMC applications. Dorman H38561 is engineered to match the original hose layout and connection style for a reliable clutch repair on vehicles such as the Chevrolet S10, Chevrolet S10 Blazer, GMC S15 Jimmy, GMC Sonoma, and GMC S15.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible clutch hydraulic hose made from EPDM rubber\u003c\/li\u003e\n\u003cli\u003e22.25 in overall length with a 15 in primary segment length\u003c\/li\u003e\n\u003cli\u003eMale M12 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for the hose ends\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required and no mounting hardware required\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is built as a replacement for the original hose used on select Chevrolet and GMC trucks and SUVs. The EPDM rubber construction provides the flexibility needed for clutch hydraulic routing, while the treated steel end fittings are formed to match the OE-style male M12 x 1.0 connection points. Use Dorman H38561 when servicing a leaking clutch line on a Chevrolet S10 or S10 Blazer, or on GMC S15 Jimmy, Sonoma, and S15 applications listed below.\u003c\/p\u003e\u003cp\u003eThis part cross-references Raybestos Brakes BH38561 and Sunsong 2204301 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1986-1991 Chevrolet S10, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1984-1991 Chevrolet S10 Blazer, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1984-1991 GMC S15 Jimmy, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1991 GMC Sonoma, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1984-1990 GMC S15, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaking clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic line loss\u003c\/li\u003e\n\u003cli\u003eFluid seepage at the hose or fitting connection\u003c\/li\u003e\n\u003cli\u003eRestoring clutch hydraulic pressure after hose failure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the hose length and both M12 x 1.0 male fittings before installation. Inspect the surrounding clutch hydraulic components for wear, corrosion, or fluid contamination, and replace any damaged lines or seals in the system as needed. Bleed the clutch hydraulic system after installation to remove air and restore proper pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle hose configurations for specific applications. H38561 is built for direct replacement use on the listed Chevrolet and GMC models.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779817078965,"sku":"BKKX-H38561","price":44.65,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38561_Fro.jpg?v=1774996072"},{"product_id":"dorman-h38678-clutch-hydraulic-hose","title":"Dorman H38678 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38678 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38678 is a replacement clutch hydraulic hose for specific Isuzu Pickup applications from 1986-1987. It is built with EPDM rubber and treated steel fittings to match the original hose layout for a direct clutch hydraulic repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement clutch hydraulic hose for 1986-1987 Isuzu Pickup\u003c\/li\u003e\n\u003cli\u003eEPDM rubber flexible hose construction\u003c\/li\u003e\n\u003cli\u003eTreated steel end fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eMale M14 x 1.5 and female M12 x 1.0 fitting types\u003c\/li\u003e\n\u003cli\u003e14-inch hose length with 12.38-inch primary segment length\u003c\/li\u003e\n\u003cli\u003eDirect replacement part number H38678\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is engineered to match the original hose configuration on the specified Isuzu Pickup fitment. The flexible EPDM rubber body helps route hydraulic fluid between clutch system components, while the treated steel fittings provide the correct thread and connection style for the application. If you are replacing a cracked or leaking clutch hose on an Isuzu Pickup, H38678 offers a vehicle-specific solution built around the original design.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., BH38678) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch pedal feels soft due to hydraulic fluid loss\u003c\/li\u003e\n\u003cli\u003eVisible cracking or wetness on the clutch hose\u003c\/li\u003e\n\u003cli\u003eHydraulic leak at the hose connection points\u003c\/li\u003e\n\u003cli\u003eDifficulty disengaging the clutch during shifting\u003c\/li\u003e\n\u003cli\u003eRestoring proper clutch hydraulic pressure on an Isuzu Pickup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify thread sizes and hose routing before installation. Inspect the surrounding clutch hydraulic components for wear, corrosion, or fluid contamination before replacing the hose. Bleed the clutch hydraulic system after installation to remove air and restore pedal feel. Confirm the vehicle application matches 1986-1987 Isuzu Pickup before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original equipment fit and function for specific vehicle applications. H38678 is built as a direct-fit clutch hydraulic hose for the listed Isuzu Pickup models.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779827859637,"sku":"BKKX-H38678","price":34.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38678_Fro.jpg?v=1774996097"},{"product_id":"dorman-h38698-clutch-hydraulic-hose","title":"Dorman H38698 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38698 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is a direct replacement for the original hose used on select Nissan Altima models. Built for a precise OE-style fit, it helps restore hydraulic clutch function when the factory hose is leaking, cracked, or worn.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber construction for flexible hydraulic routing\u003c\/li\u003e\n\u003cli\u003e21.75 in. overall length with a 20.75 in. primary segment length\u003c\/li\u003e\n\u003cli\u003eBanjo - 10 mm end 1 fitting\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 end 2 fitting\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eIncludes gaskets\u003c\/li\u003e\n\u003cli\u003eFlexible hose design for clutch hydraulic applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Replacement for Nissan Altima\u003c\/h2\u003e\u003cp\u003ePart number H38698 is engineered to match the original clutch hose configuration on 1993-2001 Nissan Altima models. It is a practical replacement for a damaged clutch hydraulic line when the original hose has developed cracks, seepage, or pressure loss. This Dorman H38698 hose is built to support a reliable clutch repair on Nissan Altima vehicles across the 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, and 2001 model years.\u003c\/p\u003e\u003cp\u003eThis part cross-references Raybestos Brakes BH38698 and Sunsong 2204340 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch fluid leakage from a cracked or deteriorated hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eDifficulty disengaging the clutch due to restricted fluid transfer\u003c\/li\u003e\n\u003cli\u003eVisible wear, swelling, or splitting in the original hose\u003c\/li\u003e\n\u003cli\u003ePressure loss in the clutch hydraulic system on Nissan Altima models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the banjo and M10 x 1.0 fitting styles before installation. Inspect the mating surfaces and replace worn seals as needed to help ensure a clean hydraulic connection. Confirm routing matches the original hose path on the vehicle to avoid kinks or contact with moving components.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this replacement hose to match the original clutch hose layout for the listed Nissan Altima applications. The EPDM rubber hose, treated steel fittings, and included gaskets support a repair focused on restoring proper hydraulic clutch operation.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779830808757,"sku":"BKKX-H38698","price":30.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38698_Fro.jpg?v=1774996101"},{"product_id":"dorman-h38699-clutch-hydraulic-hose","title":"Dorman H38699 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38699 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eRestore clutch hydraulic performance with this Dorman clutch hydraulic hose, engineered as a direct replacement for the original hose on select Nissan Maxima models. The flexible EPDM rubber construction, treated steel fittings, and included gaskets support a clean, OE-style clutch repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement clutch hydraulic hose for select Nissan Maxima applications\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose construction for flexible routing\u003c\/li\u003e\n\u003cli\u003eBanjo 10 mm end and female M10 x 1.0 end for vehicle-specific connection points\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings for durable attachment points\u003c\/li\u003e\n\u003cli\u003eIncludes gaskets for sealing at the connection points\u003c\/li\u003e\n\u003cli\u003eApproximate hose length: 23 in. with a primary segment length of 22.13 in.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman H38699 clutch hydraulic hose is built to match the original hose layout used on 1989-1993 Nissan Maxima models and 1994 Nissan Maxima vehicles built to 1\/94. It uses a flexible EPDM rubber body with treated steel fittings to help maintain proper clutch hydraulic routing and connection integrity. This part cross-references Sunsong 2201998 for the same application.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a Nissan Maxima clutch hydraulic hose, Nissan Maxima clutch line replacement, or Dorman H38699 for 1989-1994 Nissan Maxima, this hose provides the correct style of connection points and sealing components for a vehicle-specific repair.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaking clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eLoss of clutch hydraulic pressure\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose failure\u003c\/li\u003e\n\u003cli\u003eFluid seepage at hose connection points\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the banjo 10 mm and female M10 x 1.0 end fittings match the original hose before installation. Replace the sealing gaskets during service and inspect the surrounding clutch hydraulic components for wear, corrosion, or fluid contamination. Confirm fitment for 1989-1993 Nissan Maxima and 1994 Nissan Maxima built to 1\/94 before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original vehicle applications, and this hose is precision-engineered for the listed Nissan Maxima fitments. Part number H38699 is intended for direct replacement use on the specified vehicles.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779830874293,"sku":"BKKX-H38699","price":36.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38699_Fro.jpg?v=1774996102"},{"product_id":"dorman-h38703-clutch-hydraulic-hose","title":"Dorman H38703 Clutch Hydraulic Hose","description":"\u003ch2\u003eClutch Hydraulic Hose for Nissan 300ZX\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is a direct replacement for specific Nissan 300ZX applications from 1989-1996. Built with EPDM rubber and treated steel fittings, it is made to replace a leaking or cracked hose in a clutch hydraulic repair.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Dorman\u003c\/li\u003e\n\u003cli\u003ePart number: H38703\u003c\/li\u003e\n\u003cli\u003eFlexible hose construction\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material\u003c\/li\u003e\n\u003cli\u003eLength: 16.06 in.\u003c\/li\u003e\n\u003cli\u003eEnd 1 fitting: Banjo - 10 mm\u003c\/li\u003e\n\u003cli\u003eEnd 2 fitting: Female - M10 x 1.0\u003c\/li\u003e\n\u003cli\u003eGaskets included\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Replacement Details\u003c\/h2\u003e\u003cp\u003eDorman H38703 is precision-engineered to match the original clutch hose layout used on select Nissan 300ZX models. The flexible hose design and OE-style end fittings help restore hydraulic connection integrity in the clutch system, making it a practical choice for a Nissan 300ZX clutch hydraulic hose replacement or a 1990-1996 Nissan 300ZX clutch line repair. This part cross-references Centric Parts 151.42015 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible cracking in the clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eFluid leakage at the hose or fitting connection\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eLoss of clutch hydraulic pressure during operation\u003c\/li\u003e\n\u003cli\u003eNeed for a direct replacement during clutch system service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Fitment\u003c\/h2\u003e\u003cp\u003eCompatible With 1989 Nissan 300ZX, from 2\/89, and 1990-1996 Nissan 300ZX. Verify the banjo and M10 x 1.0 connections, hose length, and routing before installation. Use the included gaskets during assembly and inspect the surrounding clutch hydraulic components for wear or contamination. Part number H38703 is intended for specific Nissan 300ZX clutch hydraulic hose applications only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle specifications for repair-focused service work. H38703 is built with EPDM rubber and treated steel fittings to support a reliable clutch hydraulic repair on the listed Nissan 300ZX applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779830972597,"sku":"BKKX-H38703","price":28.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38703_Fro.jpg?v=1774996102"},{"product_id":"dorman-h38761-clutch-hydraulic-hose","title":"Dorman H38761 Clutch Hydraulic Hose","description":"\u003ch2\u003eClutch Hydraulic Hose for Mazda RX-7\u003c\/h2\u003e\u003cp\u003eDorman H38761 is a replacement clutch hydraulic hose for specific 1986-1991 Mazda RX-7 applications. It is built with EPDM rubber and treated steel fittings to match the original hose layout for a direct repair on the clutch hydraulic system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacement clutch hydraulic hose for 1986-1991 Mazda RX-7\u003c\/li\u003e\n\u003cli\u003eFlexible EPDM rubber construction for hydraulic routing\u003c\/li\u003e\n\u003cli\u003eMale M10 x 1.0 end and female M10 x 1.0 end\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003e10.5-inch length for OE-style fitment\u003c\/li\u003e\n\u003cli\u003eDorman H38761 for clutch hydraulic hose replacement service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eWhen the original hose is leaking, cracked, or deteriorated, Dorman H38761 provides a direct replacement for the clutch hydraulic line on the Mazda RX-7. This flexible hose is precision-engineered to match the original hose design on listed vehicles, helping restore hydraulic integrity in the clutch system. The EPDM rubber body is paired with treated steel fittings, including a male M10 x 1.0 end and a female M10 x 1.0 end, for a factory-style connection. This part cross-references Sunsong 2204018 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible fluid leakage at the clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eCracked, swollen, or aged rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eDifficulty maintaining clutch hydraulic pressure\u003c\/li\u003e\n\u003cli\u003eNeed for a direct replacement during clutch system repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify hose length, fitting thread size, and routing before installation. Inspect the surrounding clutch hydraulic components for wear, corrosion, or fluid contamination before installing the new hose. Bleed the clutch hydraulic system after installation to remove air and restore proper pedal operation. Fits 1986-1991 Mazda RX-7, N\/A.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle applications, helping support a reliable clutch repair on the Mazda RX-7. Dorman H38761 is built for direct-fit service on the listed vehicles.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779844341941,"sku":"BKKX-H38761","price":28.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38761_Fro.jpg?v=1774996109"},{"product_id":"dorman-h38762-clutch-hydraulic-hose","title":"Dorman H38762 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38762 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic hose with a direct-fit style solution built for specific applications. Dorman H38762 is a flexible EPDM rubber hose engineered to match the original clutch hose layout on 1988-1989 Mazda 323 models, helping restore hydraulic clutch function with the correct end fittings and length.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFlexible EPDM rubber construction for hydraulic clutch service\u003c\/li\u003e\n\u003cli\u003eLength: 17.91 in. for application-specific routing\u003c\/li\u003e\n\u003cli\u003eMale M10 x 1.0 end 1 fitting\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 end 2 fitting\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings for secure connection points\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required and no mounting hardware required\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eCompatible with 1988-1989 Mazda 323 clutch hydraulic systems. This Dorman H38762 hose is built around the original hose configuration for those Mazda 323 model years, making it a practical replacement when the factory hose is leaking, swollen, or cracked. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Hose Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch pedal that loses hydraulic pressure\u003c\/li\u003e\n\u003cli\u003eVisible fluid seepage at the hose or fittings\u003c\/li\u003e\n\u003cli\u003eCracked, hardened, or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose leakage\u003c\/li\u003e\n\u003cli\u003eHydraulic clutch performance issues on Mazda 323 vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the end fitting types, hose length, and routing before installation. Inspect the surrounding clutch hydraulic components for contamination or wear, and replace damaged seals or related parts as needed since no gasket or seal is included. Proper bleeding of the clutch hydraulic system after installation is required to restore pedal feel and operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts engineered to match original vehicle-specific designs, and H38762 is built to follow the OE-style hose configuration for the listed Mazda 323 applications. Part number H38762 is also referenced in aftermarket catalogs for the same fitment.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779846078645,"sku":"BKKX-H38762","price":33.41,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38762_Fro.jpg?v=1774996110"},{"product_id":"dorman-h38763-clutch-hydraulic-hose","title":"Dorman H38763 Clutch Hydraulic Hose - Upper","description":"\u003ch2\u003eDorman H38763 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic hose with a direct-fit style solution built for specific Mazda applications. Dorman H38763 is a flexible EPDM rubber hose with treated steel female M10 x 1.0 fittings on both ends for a precise replacement on select Mazda B-series trucks.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible EPDM rubber construction for clutch hydraulic routing\u003c\/li\u003e\n\u003cli\u003eLength: 6.75 in.\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for durability\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo bracket required and no mounting hardware required\u003c\/li\u003e\n\u003cli\u003eCompatible with select 1986-1993 Mazda B2000, B2200, and B2600 upper applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is engineered to match the original hose design used on specific vehicles, helping restore proper hydraulic fluid transfer in the clutch system. The EPDM rubber body provides flexibility for routing, while the treated steel end fittings are built for secure connection points. Dorman H38763 is a practical replacement for owners servicing a Mazda B2200 clutch hydraulic hose, Mazda B2600 clutch hydraulic hose, or Mazda B2000 clutch hydraulic hose in the upper position.\u003c\/p\u003e\u003cp\u003eThis part cross-references Raybestos Brakes BH38763 and Sunsong 2203693 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible hydraulic fluid leakage at the hose\u003c\/li\u003e\n\u003cli\u003eCracking or dry rot in the hose body\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose failure\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch circuit\u003c\/li\u003e\n\u003cli\u003eDifficulty shifting related to clutch hydraulic line damage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the upper-position routing and both female M10 x 1.0 connections before installation. Inspect the surrounding clutch hydraulic components for wear, contamination, or corrosion so the repair addresses the full source of the leak. Confirm vehicle application by year, make, and model before ordering; Dorman H38763 is listed for 1986-1987 Mazda B2000, 1987-1993 Mazda B2200, and 1987-1993 Mazda B2600 upper applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original equipment-style fit and function for specific vehicle applications. Part number H38763 is built as a direct replacement hose for targeted Mazda clutch hydraulic service.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779846635701,"sku":"BKKX-H38763","price":25.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38763_Fro.jpg?v=1774996110"},{"product_id":"dorman-h38787-clutch-hydraulic-hose","title":"Dorman H38787 Clutch Hydraulic Hose - Front Left or Front Right","description":"\u003ch2\u003eDorman H38787 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38787 is a flexible clutch hydraulic hose built for specific Toyota MR2 applications from 1985-1989. It is engineered to match original fit, function, and performance for front left and front right positions, with OE-style connections and durable EPDM rubber construction.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1985-1989 Toyota MR2, front left\u003c\/li\u003e\n\u003cli\u003eFits 1985-1989 Toyota MR2, front right\u003c\/li\u003e\n\u003cli\u003eFlexible hose design with black rubber outer sleeve\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material for hydraulic service\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings with banjo and female ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 19.5 in.\u003c\/li\u003e\n\u003cli\u003eGaskets included; mounting hardware and bracket not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose, part number H38787, is designed for Toyota MR2 models from 1985 through 1989 and is listed for front left and front right positions. The hose uses treated steel end fittings, a 10 mm banjo connection on one end, and an M10 x 1.0 female connection on the other to match the original hydraulic routing on the vehicle. The EPDM rubber hose and black outer sleeve are selected for flexible brake and clutch hydraulic service, while the included gaskets support a proper seal during replacement. This part cross-references Centric Parts 150.44044 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLeaking clutch hydraulic hose on a Toyota MR2\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel\u003c\/li\u003e\n\u003cli\u003eVisible cracking, swelling, or fluid seepage at the hose\u003c\/li\u003e\n\u003cli\u003eHydraulic pressure loss in the clutch system\u003c\/li\u003e\n\u003cli\u003eReplacement during brake and clutch hydraulic service on 1985-1989 Toyota MR2 models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the hose routing, fitting style, and position before installation. Replace the gaskets during service and inspect the surrounding hydraulic lines, master cylinder, and slave cylinder for wear or leakage. Because mounting hardware and bracket are not included, reuse or source any required vehicle-specific retainers as needed. Confirm the application against the vehicle’s original hose length and connection type before final assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this hose to match the fit, function, and performance of the original hose on the specified vehicles and positions. The part number is H38787.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779847094453,"sku":"BKKX-H38787","price":34.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38787_Fro.jpg?v=1774996111"},{"product_id":"dorman-h38790-clutch-hydraulic-hose","title":"Dorman H38790 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38790 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38790 is a flexible clutch hydraulic hose built for specific Toyota applications, with OE-style fit and function for reliable hydraulic transfer. It uses EPDM rubber construction with treated steel female fittings to support a secure connection in the clutch hydraulic system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose design for clutch hydraulic routing\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material with black outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 15.38 in.\u003c\/li\u003e\n\u003cli\u003eEnd 1 thread diameter: 10 mm; End 2 fitting inside diameter: M10 x 1.0\u003c\/li\u003e\n\u003cli\u003eDirect replacement style for select Toyota Celica, Corolla, and Camry applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman H38790 clutch hydraulic hose is engineered to match the fit, function, and performance of the original hose used on select Toyota vehicles. It is a flexible hose assembly with EPDM rubber construction and treated steel end fittings, built for the hydraulic demands of clutch operation. This part cross-references Raybestos Brakes BH38790 for the same application. It is used on 1990-1993 Toyota Celica, 1990-1993 Toyota Corolla, and 1989-1991 Toyota Camry applications, including rear left and rear right positions where specified. For Toyota Celica service, H38790 also covers 1990-1991 rear left and rear right positions except Wide Body models.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFluid leakage from a worn or damaged clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eRestricted hydraulic flow from cracked or aging rubber lines\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the hose end fittings\u003c\/li\u003e\n\u003cli\u003eService replacement for select Toyota Celica, Corolla, and Camry clutch hydraulic routing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and position before installation. Confirm the 10 mm thread and M10 x 1.0 fitting interface match the original hose connection points. Mounting hardware, brackets, gaskets, seals, and jacket are not included, so reuse or source the required vehicle-specific components as needed. Inspect adjacent hydraulic components and bleed the system after installation to restore proper clutch operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this hose to replicate the original part’s fit and function for the listed Toyota applications. The EPDM rubber hose and treated steel fittings are selected for durable hydraulic service in clutch system use.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779849224373,"sku":"BKKX-H38790","price":30.81,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38790_Fro.jpg?v=1774996112"},{"product_id":"dorman-h38793-clutch-hydraulic-hose","title":"Dorman H38793 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38793 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eDorman H38793 is a flexible clutch hydraulic hose built with EPDM rubber and treated steel female fittings for a direct-fit replacement on select Toyota vehicles. It is engineered to match the original hose’s fit, function, and performance for dependable hydraulic transfer in brake and clutch service applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFlexible hose construction for routing in tight chassis locations\u003c\/li\u003e\n\u003cli\u003eEPDM rubber hose material with black outer sleeve\u003c\/li\u003e\n\u003cli\u003eTreated steel female fittings on both ends\u003c\/li\u003e\n\u003cli\u003eOverall length: 12.5 in.\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Toyota 4Runner, Tercel, Paseo, and Corolla applications\u003c\/li\u003e\n\u003cli\u003ePart number H38793 for catalog and cross-reference lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is built to restore proper hydraulic line routing and fluid transfer where the original hose has worn, cracked, or leaked. The flexible EPDM rubber body helps maintain the correct path between connection points, while the treated steel female fittings provide a secure interface at each end. H38793 is listed for select 1988-2000 Toyota applications, including 1996-2000 Toyota 4Runner, 1991-1996 Toyota Tercel, 1998-1999 Toyota Tercel, 1992-1996 Toyota Paseo, and 1988-1992 Toyota Corolla rear left and rear right positions. This part cross-references Raybestos Brakes BH38793 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a leaking or cracked clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eRestoring hydraulic pressure loss in the clutch line\u003c\/li\u003e\n\u003cli\u003eCorrecting soft or inconsistent clutch pedal response caused by hose deterioration\u003c\/li\u003e\n\u003cli\u003eRepairing corrosion or wear at the hose fittings\u003c\/li\u003e\n\u003cli\u003eAddressing fluid seepage in select Toyota brake and hydraulic line service locations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle year, model, and position before installation. Confirm the end fittings match the original connection style and thread size, including the M10 x 1.0 specification listed for this hose. Inspect adjoining hard lines, seals, and mounting points for wear before completing the repair. Mounting hardware, brackets, and seals are not included.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman engineers this hose to match original fit and function on the listed vehicles and positions. The EPDM rubber construction and treated steel fittings are selected for long-lasting service in hydraulic brake and clutch line applications. Part number H38793 is intended for direct replacement use on the confirmed Toyota fitments shown above.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779849683125,"sku":"BKKX-H38793","price":28.77,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38793_Fro.jpg?v=1774996112"},{"product_id":"dorman-h38830-clutch-hydraulic-hose","title":"Dorman H38830 Clutch Hydraulic Hose","description":"\u003ch2\u003eDorman H38830 Clutch Hydraulic Hose for Honda Accord\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic hose with a direct-fit service part engineered for specific Honda applications. Dorman H38830 is built with EPDM rubber and treated steel fittings to match the original hose layout on 1990-1991 Honda Accord models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber flexible hose construction\u003c\/li\u003e\n\u003cli\u003eLength: 12.75 in. with 11.75 in. primary segment length\u003c\/li\u003e\n\u003cli\u003eBanjo 10 mm end 1 fitting and female M12 x 1.0 end 2 fitting\u003c\/li\u003e\n\u003cli\u003eTreated steel fittings with stamped steel bracket material\u003c\/li\u003e\n\u003cli\u003eGaskets included for the hydraulic connection points\u003c\/li\u003e\n\u003cli\u003eCompatible with 1990-1991 Honda Accord clutch hydraulic hose replacement needs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose, part number H38830, is precision-engineered to match the original hose configuration used on 1990-1991 Honda Accord vehicles. The flexible EPDM rubber body is paired with treated steel ends for a service replacement that follows the OE-style routing and connection style. If you are searching for a 1990 Honda Accord clutch hydraulic hose or a 1991 Honda Accord hydraulic hose replacement, H38830 provides the correct fitment for those applications. This part cross-references Raybestos Brakes BH38830 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Hose Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible cracking in the clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eFluid leakage at the hose or fitting connections\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hydraulic loss\u003c\/li\u003e\n\u003cli\u003eDamage from age, heat, or road exposure\u003c\/li\u003e\n\u003cli\u003eNeed for a direct replacement during clutch hydraulic service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle application before installation and compare the banjo and female threaded ends to the original hose. Replace worn gaskets during service and inspect the surrounding clutch hydraulic components for leaks, corrosion, or damaged mounting points. Proper bleeding of the hydraulic system is required after installation to restore pedal operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures replacement parts to match original vehicle specifications for targeted applications. H38830 is built as a direct replacement clutch hydraulic hose for confirmed Honda Accord fitment.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779864035509,"sku":"BKKX-H38830","price":27.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38830_Fro.jpg?v=1774996118"},{"product_id":"dorman-h38877-clutch-hydraulic-hose","title":"Dorman H38877 Clutch Hydraulic Hose - Rear Left or Rear Right","description":"\u003ch2\u003eDorman H38877 Clutch Hydraulic Hose\u003c\/h2\u003e\u003cp\u003eReplace a leaking or cracked clutch hydraulic hose with a direct-fit style replacement built for specific Toyota applications. Dorman H38877 is engineered to match the original hose layout and connection style for a reliable clutch repair on select Toyota Celica and Toyota Camry models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEPDM rubber construction for hydraulic hose service\u003c\/li\u003e\n\u003cli\u003e14.75 in. overall length\u003c\/li\u003e\n\u003cli\u003eFemale M10 x 1.0 fittings on both ends\u003c\/li\u003e\n\u003cli\u003eTreated steel fitting material for added durability\u003c\/li\u003e\n\u003cli\u003eRubber jacket material\u003c\/li\u003e\n\u003cli\u003eNo bracket required and no mounting hardware required\u003c\/li\u003e\n\u003cli\u003eDirect replacement for select Toyota clutch hydraulic hose applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman clutch hydraulic hose is built to replace the original hose on specific Toyota vehicles where the factory line has developed leaks, cracks, or pressure loss. The hose uses EPDM rubber and treated steel end fittings to match the original connection style, helping restore hydraulic transfer between the clutch master and slave cylinder. It is a practical replacement for Toyota Camry rear left and rear right applications from 1987-1991, as well as Toyota Celica rear left and rear right applications from 1986-1989 and 1990-1993. This part number, H38877, is also referenced in aftermarket catalogs for the same application.\u003c\/p\u003e\u003cp\u003eThis part cross-references Centric Parts 150.44342 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVisible fluid seepage at the clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated rubber hose material\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel\u003c\/li\u003e\n\u003cli\u003eLoss of hydraulic pressure in the clutch system\u003c\/li\u003e\n\u003cli\u003eDifficulty disengaging the clutch during shifting\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify hose routing, end fitting thread size, and vehicle position before installation. This hose uses female M10 x 1.0 fittings on both ends and does not require a bracket or mounting hardware. After installation, bleed the clutch hydraulic system and inspect all connections for leaks. Confirm the replacement matches the original hose length and routing on your Toyota Camry or Toyota Celica application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman replacement hydraulic hoses are engineered to match original equipment dimensions and connection points for specific vehicle applications. Part number H38877 is built for direct replacement use on confirmed Toyota fitments.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779875930293,"sku":"BKKX-H38877","price":25.08,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38877_Fro.jpg?v=1774996127"},{"product_id":"dorman-h38927-clutch-hydraulic-hose","title":"Dorman H38927 Clutch Hydraulic Hose - Rear Center","description":"\u003ch2\u003eClutch Hydraulic Hose for Toyota Applications\u003c\/h2\u003e\u003cp\u003eDorman H38927 is a flexible clutch hydraulic hose built to match the fit, function, and performance of the original hose on specific Toyota vehicles and positions. It uses an EPDM rubber hose body with treated steel male and female ends for a direct replacement on select Land Cruiser, Cressida, and Celica applications.\u003c\/p\u003e\u003cp\u003eFor Toyota Land Cruiser rear center service, this hose supports a clean hydraulic connection where the original line has aged, cracked, or begun to leak. The black rubber construction and OE-style end fittings help restore proper clutch hydraulic routing and pedal response.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement clutch hydraulic hose for select Toyota vehicles\u003c\/li\u003e\n\u003cli\u003eFlexible hose design with EPDM rubber outer hose material\u003c\/li\u003e\n\u003cli\u003eBlack finish for a factory-style appearance\u003c\/li\u003e\n\u003cli\u003eTreated steel end fittings with male and female connections\u003c\/li\u003e\n\u003cli\u003eOverall length: 13.5 in.\u003c\/li\u003e\n\u003cli\u003eEnd 1 thread diameter: 10 mm\u003c\/li\u003e\n\u003cli\u003eEnd 2 fitting inside diameter: M10 x 1.0\u003c\/li\u003e\n\u003cli\u003eCompatible with rear center applications listed below\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman H38927 is engineered as an OE-style clutch hydraulic hose for specific Toyota fitments, including 1991-1995 Toyota Land Cruiser rear center applications, plus 1983-1987 Toyota Cressida and 1984-1986 Toyota Celica. The hose is built with EPDM rubber for hydraulic service and treated steel fittings to match the original connection style. If you are replacing a worn Toyota Land Cruiser clutch hose or servicing a classic Toyota Cressida or Celica hydraulic line, H38927 provides the correct hose format for the listed positions. This part cross-references Raybestos Brakes BH38927 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFluid leakage from a cracked or deteriorated clutch hydraulic hose\u003c\/li\u003e\n\u003cli\u003eSoft or inconsistent clutch pedal feel caused by hose wear\u003c\/li\u003e\n\u003cli\u003eHydraulic line damage from age, heat, or road exposure\u003c\/li\u003e\n\u003cli\u003eLoss of clutch hydraulic pressure at the rear center routing point\u003c\/li\u003e\n\u003cli\u003eReplacement needs during Toyota clutch hydraulic system repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle position, fitting style, and thread size before installation. This hose does not include mounting hardware, brackets, or seals, so reuse or source the required related components as needed. Confirm routing length and connection orientation against the original part before tightening the treated steel fittings.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman engineers this hose to match the fit, function, and performance of the original hose on the listed vehicles and positions. It is built for long-lasting durability as part of a complete hydraulic repair on compatible Toyota applications. Part number H38927 is the reference to use when ordering or cross-checking service parts.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 1995 Toyota Land Cruiser, rear center\u003c\/li\u003e\n\u003cli\u003eFits 1991-1994 Toyota Land Cruiser, rear center\u003c\/li\u003e\n\u003cli\u003eFits 1983-1987 Toyota Cressida, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1984-1986 Toyota Celica, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43779881762997,"sku":"BKKX-H38927","price":31.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/DB_H38927_Fro_30c1a5ae-0450-4a96-bb03-98553d60d785.jpg?v=1774996136"}],"url":"https:\/\/www.partcatalog.com\/collections\/hoses-and-pipes-9.oembed?page=5","provider":"PartCatalog","version":"1.0","type":"link"}