{"title":"Driveline and Axles \u003e Hubs and Related Components","description":"\u003cp\u003eWheel bearings and hub assemblies are the interface between your rotating wheel and stationary suspension — they carry the vehicle's weight while allowing the wheel to spin freely. On most modern vehicles, the wheel bearing is integrated into a sealed hub assembly pressed into the knuckle or bolted directly to it, replacing the old-style serviceable tapered roller bearing. These units typically last 85,000–100,000 miles under normal conditions, though aggressive cornering loads, water intrusion, or a hard pothole hit can shorten that significantly. Symptoms range from a subtle hum at highway speeds to a pronounced grinding that changes pitch when you steer. When buying, match the hub assembly to your specific year, make, model, and trim — ABS tone rings, bolt patterns, and flange diameters vary widely even within the same nameplate. OEM-spec units with double-sealed bearings and pre-set preload are the standard to match; budget-tier assemblies often use lighter-duty seals that fail early in wet or salty climates.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCyclic humming or growling noise at highway speeds\u003c\/strong\u003e that changes pitch or volume when you shift your weight by changing lanes — this is the classic failing wheel bearing signature, caused by worn or pitted bearing races.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eGrinding or rumbling that intensifies when turning\u003c\/strong\u003e in one direction indicates the bearing on that side is under load and failing; a right-turn grind typically points to the left hub assembly.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLoose or wobbly wheel with visible play\u003c\/strong\u003e when the wheel is grabbed at the 3 and 9 o'clock positions and rocked — more than 0.005 inches of radial play means the bearing is worn beyond spec.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eABS warning light triggered without a brake fault\u003c\/strong\u003e can indicate a damaged or corroded ABS tone ring integrated into the hub assembly, giving the control module erratic wheel speed readings.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eUneven or rapid tire wear on one corner\u003c\/strong\u003e, particularly feathering or cupping on the inner or outer edge, can result from bearing play introducing inconsistent wheel alignment loads while driving.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eVibration felt through the steering wheel or floorboard\u003c\/strong\u003e at a specific speed range (typically 45–65 mph) that doesn't match tire imbalance frequency and doesn't respond to tire rotation or rebalancing.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHow long do wheel bearing and hub assemblies typically last, and should I replace both sides at the same time?\u003c\/strong\u003e\n  Most sealed hub assemblies last 85,000–100,000 miles, but mileage and environment vary. If one side fails, the other has usually seen the same wear and road exposure. Replacing both sides during the same job is common shop practice and saves labor cost if the second bearing fails within a year.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eAre aftermarket hub assemblies as reliable as OEM, or is OEM worth the premium?\u003c\/strong\u003e\n  Quality varies significantly in the aftermarket. Brands like Timken, SKF, and Moog manufacture to OEM tolerances and are widely trusted by professional shops. Generic or unbranded assemblies often use lighter seals and lower-grade bearing steel. For daily drivers in salt-belt states, spending the extra $20–40 on a name-brand unit is consistently worth it.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat does a wheel bearing and hub assembly replacement cost, and what else should I replace at the same time?\u003c\/strong\u003e\n  Parts run $60–$180 per corner depending on vehicle; labor adds $100–$200 per side at a shop. DIY is straightforward on front-wheel-drive vehicles with basic tools, though rear assemblies on AWD platforms can require a press. While the knuckle is off, inspect the CV axle shaft, outer tie rod end, and ball joint — all are accessible at zero additional labor cost.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"beck-arnley-051-6003-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6003 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eBeck Arnley Rear Wheel Bearing Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6003 is a rear wheel bearing and hub assembly built to foreign nameplate OE specifications for form, fit, and function. It is a ball-type hub assembly with a 4-lug pattern and no ABS sensor cord, making it a direct replacement choice for select Honda Civic, Honda CRX, Honda Civic del Sol, and Acura EL rear applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBall-type rear wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003e4-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eNo ABS sensor cord included\u003c\/li\u003e\n\u003cli\u003eGeneration 2 design\u003c\/li\u003e\n\u003cli\u003eOE-spec replacement from Beck Arnley\u003c\/li\u003e\n\u003cli\u003ePart number 051-6003 for application matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis Beck Arnley wheel bearing and hub assembly is engineered for rear axle service on select compact Honda and Acura platforms. It fits 1997-2000 Acura EL, rear; 1985-2000 Honda Civic, rear; 1993-1995 Honda Civic del Sol, rear; and 1988-1991 Honda CRX, rear. The 051-6003 hub assembly is a practical OE-style replacement when the original rear hub shows wear, noise, or looseness.\u003c\/p\u003e\u003cp\u003eBeck Arnley sources parts to match foreign nameplate OE requirements, helping ensure the correct form and function for Honda Civic rear hub replacement and Acura EL rear wheel bearing service. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rumble\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear hub support on Honda Civic and CRX models\u003c\/li\u003e\n\u003cli\u003eReplacing a worn rear hub assembly on Acura EL vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment by year, model, and position before installation. The axle nut is not included, so reuse or source the correct axle nut separately as required for the vehicle. Inspect related rear suspension and axle components during service, and verify that the hub mounting surfaces are clean before assembly. Use the part number 051-6003 to confirm the correct application for your Honda Civic, Honda CRX, Honda Civic del Sol, or Acura EL.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. Global sourcing support and application-focused cataloging help provide a reliable OE-style replacement for rear wheel bearing and hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388304916661,"sku":"BBGB-051-6003","price":92.72,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516003_Oth.jpg?v=1774710535"},{"product_id":"beck-arnley-051-6089-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6089 Wheel Bearing and Hub Assembly - Rear Right","description":"\u003ch2\u003eRear Right Wheel Bearing Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6089 is a rear right wheel bearing and hub assembly for select Toyota and Lexus applications. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the original rear hub assembly on covered vehicles.\u003c\/p\u003e\u003cp\u003eCompatible with 2001-2003 Toyota Highlander, rear right, and other listed Toyota Camry, Avalon, Solara, and Lexus ES applications, this assembly is built around the correct bearing type, lug pattern, and ABS sensor configuration for the application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBeck Arnley 051-6089 wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eRear right position for select Toyota and Lexus models\u003c\/li\u003e\n\u003cli\u003eBall bearing type for the specified application\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eEnd cap ABS sensor type\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eBuilt to OE specifications for form, fit, and function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Beck Arnley hub assembly is engineered for foreign nameplate vehicles where OE-style fitment matters. It is a direct replacement for rear right applications on 2002-2011 Toyota Camry, 2005-2012 Toyota Avalon, 2004-2008 Toyota Solara, 2004-2006 Lexus ES330, 2002-2003 Lexus ES300, 2007-2012 Lexus ES350, and 2001-2003 Toyota Highlander. The part number 051-6089 is a practical match for repair work that requires the correct hub geometry, bearing style, and ABS sensor arrangement.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed interchange numbers in the provided data.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores a worn or noisy rear wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eAddresses wheel play or looseness at the rear right corner\u003c\/li\u003e\n\u003cli\u003eReplaces a hub assembly with ABS sensor-related fitment concerns\u003c\/li\u003e\n\u003cli\u003eSupports proper wheel mounting on 5-lug applications\u003c\/li\u003e\n\u003cli\u003eHelps correct driveline vibration or rough rolling caused by hub wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2007-2012 Lexus ES350, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2005-2012 Toyota Avalon, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2002-2011 Toyota Camry, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Toyota Solara, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Lexus ES330, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Lexus ES300, rear right; may require ABS harness, check catalog\u003c\/li\u003e\n\u003cli\u003eFits 2001-2003 Toyota Highlander, rear right; axle nut is not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eVerify the vehicle year, model, and rear right position before installation. Confirm ABS harness requirements against the catalog for the specific application, and reuse or source any required axle nut separately where noted.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet OE specifications for foreign nameplate vehicles, with product specialists working through global sourcing partners to help ensure the correct fit for the application. Beck Arnley 051-6089 is built for the listed Toyota and Lexus rear right hub applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388304982197,"sku":"BBGB-051-6089","price":151.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516089_Oth.jpg?v=1774710539"},{"product_id":"beck-arnley-051-6124-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6124 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Hyundai Tiburon\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6124 is a rear wheel bearing and hub assembly built to match foreign nameplate OE specifications for form, fit, and function. It is a direct-fit service part for 2003-2005 Hyundai Tiburon rear applications, with a ball bearing design, 5-lug hub pattern, and axle nut included.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2003-2005 Hyundai Tiburon\u003c\/li\u003e\n\u003cli\u003eBall bearing type for service replacement applications\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eAxle nut included\u003c\/li\u003e\n\u003cli\u003eABS sensor cord not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6124\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Information\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6124 is engineered for rear driveline and axle service on the Hyundai Tiburon. The assembly follows OE-style specifications for fit and function, helping restore proper wheel support and hub operation on the rear axle. This part number 051-6124 is a practical choice when replacing a worn or noisy rear hub assembly on 2003, 2004, or 2005 Hyundai Tiburon models.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive hub play or looseness\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eVibration from a worn rear hub assembly\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged 5-lug rear hub\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment before installation on 2003-2005 Hyundai Tiburon models. Verify the ABS sensor cord requirement for your vehicle, since this assembly is listed without an ABS sensor cord. Inspect the axle nut and surrounding hardware during service, and follow factory torque specifications during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley sources parts to meet foreign nameplate OE specifications for form, fit, and function. The brand works with global sourcing partners to help ensure the replacement part matches the intended application with confidence.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305670325,"sku":"BBGB-051-6124","price":98.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516124_Oth.jpg?v=1774710542"},{"product_id":"beck-arnley-051-6144-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6144 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Toyota Sienna\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6144 is a rear wheel bearing and hub assembly for the 2004-2010 Toyota Sienna. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for rear hub service on this application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Toyota Sienna\u003c\/li\u003e\n\u003cli\u003eBeck Arnley 051-6144 for 2004-2010 Toyota Sienna rear applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for this hub assembly design\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eEnd cap ABS sensor type\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eAxle nut is not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6144 is engineered for the rear of the 2004-2010 Toyota Sienna and follows OE-style specifications for fit and function. This rear wheel bearing and hub assembly uses a ball bearing design, a 5-lug pattern, and an end cap ABS sensor type, making it a direct service part for rear hub replacement on the Toyota Sienna. Beck Arnley sources parts through a global network to match the original application requirements, and the 051-6144 part number is the reference to use when ordering or verifying the correct rear hub assembly.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Repair\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel noise caused by a worn bearing\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eABS warning concerns related to the rear hub sensor interface\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation from a failing hub assembly\u003c\/li\u003e\n\u003cli\u003eService issues on a 2004-2010 Toyota Sienna rear wheel bearing and hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2004-2010 Toyota Sienna, rear. Verify the ABS sensor style and 5-lug hub configuration before installation. The axle nut is not included, so confirm the existing hardware condition during service. Use the Beck Arnley 051-6144 part number to match the correct rear application before removing the original hub assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are built to meet foreign nameplate OE specifications for form, fit, and function. The 051-6144 is sourced through Beck Arnley’s global partner network to support correct application matching for the Toyota Sienna rear hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305735861,"sku":"BBGB-051-6144","price":130.15,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516144_Oth.jpg?v=1774710544"},{"product_id":"beck-arnley-051-6150-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6150 Wheel Bearing and Hub Assembly - Front or Rear","description":"\u003ch2\u003eOE-Style Wheel Hub Assembly for Hyundai and Kia\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 051-6150 wheel bearing and hub assembly is built for foreign nameplate applications that call for OE-level form, fit, and function. It is a direct replacement for select Hyundai Santa Fe, Santa Fe XL, Santa Fe Sport, Veracruz, and Kia Sorento models with rear or front hub applications depending on vehicle year and configuration.\u003c\/p\u003e\u003cp\u003eBeck Arnley sources parts through a global network to match the original equipment specifications needed for a confident repair. This hub assembly uses a ball bearing design, includes 5 wheel studs with M12 stud size, and is configured with 30 splines.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBeck Arnley 051-6150 wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for select Hyundai and Kia driveline applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for hub service replacement\u003c\/li\u003e\n\u003cli\u003e30-spline configuration\u003c\/li\u003e\n\u003cli\u003e5-lug hub with 5 wheel studs and M12 stud size\u003c\/li\u003e\n\u003cli\u003eABS sensor ring not included\u003c\/li\u003e\n\u003cli\u003eFlange bolts not included\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 051-6150 is a wheel bearing and hub assembly engineered for foreign nameplate vehicles that require OE specifications for form, fit, and function. It is used on rear applications for 2007-2018 Hyundai Santa Fe, 2013-2018 Hyundai Santa Fe Sport, and 2013-2019 Hyundai Santa Fe XL, as well as front and rear applications on 2007-2012 Hyundai Veracruz and 2011-2015 Kia Sorento. Front applications also include 2007-2014 Hyundai Santa Fe and 2013-2014 Hyundai Santa Fe XL. This part number, 051-6150, is a practical replacement choice when restoring wheel-end support and hub mounting integrity on these vehicles.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing noise from a worn hub assembly\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play or looseness at the hub\u003c\/li\u003e\n\u003cli\u003eUneven wheel-end rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eHub mounting issues on select Hyundai Santa Fe and Kia Sorento applications\u003c\/li\u003e\n\u003cli\u003eABS-related service needs when the original sensor ring is retained separately\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify front or rear position before ordering; fitment varies by model year.\u003c\/li\u003e\n\u003cli\u003eAxle nut is not included, so confirm the existing hardware condition before installation.\u003c\/li\u003e\n\u003cli\u003eCheck spline count, wheel stud size, and lug pattern against the original part.\u003c\/li\u003e\n\u003cli\u003eInspect related suspension and brake components during hub replacement.\u003c\/li\u003e\n\u003cli\u003eConfirm ABS sensor ring requirements for the vehicle, since this assembly does not include one.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The 051-6150 is built to align with the original application requirements for Hyundai Santa Fe, Hyundai Santa Fe XL, Hyundai Santa Fe Sport, Hyundai Veracruz, and Kia Sorento hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305768629,"sku":"BBGB-051-6150","price":171.13,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516150_Oth.jpg?v=1774710545"},{"product_id":"beck-arnley-051-6161-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6161 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Honda Accord\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6161 is a rear wheel bearing and hub assembly for 1998-2002 Honda Accord applications. It is built to match foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the rear hub service on the Accord.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 1998-2002 Honda Accord\u003c\/li\u003e\n\u003cli\u003eBall bearing type for rear hub service\u003c\/li\u003e\n\u003cli\u003e4-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eGeneration 2 design\u003c\/li\u003e\n\u003cli\u003eABS sensor cord not included\u003c\/li\u003e\n\u003cli\u003eType 2\/E10 application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Fit and Application Details\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6161 is engineered for the rear position on 1998, 1999, 2000, 2001, and 2002 Honda Accord models. The assembly follows OE-style specifications so the hub, bearing, and mounting dimensions align with the original rear driveline setup. This part number, 051-6161, is a practical choice when servicing a Honda Accord rear wheel bearing and hub assembly with a 4-lug layout.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise such as humming or growling\u003c\/li\u003e\n\u003cli\u003eExcessive play or looseness at the rear hub\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eHub service needs on a 4-lug Honda Accord rear assembly\u003c\/li\u003e\n\u003cli\u003eABS-related service where the sensor cord is not part of the assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment by year and position before installation on the Honda Accord. Inspect the axle nut condition during service, since the axle nut is not included with Beck Arnley 051-6161. Verify bearing seating, hub alignment, and torque specifications against the vehicle service manual during reassembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley sources parts to meet foreign nameplate OE specifications for form, fit, and function. The brand works with global sourcing partners to help ensure the correct rear wheel bearing and hub assembly is selected for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305834165,"sku":"BBGB-051-6161","price":111.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516161_Oth.jpg?v=1774710546"},{"product_id":"beck-arnley-051-6181-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6181 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Honda Civic\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6181 is a rear wheel bearing and hub assembly for select 2006-2011 Honda Civic models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for rear hub service on the Honda Civic.\u003c\/p\u003e\u003cp\u003eCompatible with 2006-2011 Honda Civic rear applications, this assembly uses a ball bearing design and a magnetic encoder in the seal for ABS signal integration. Beck Arnley 051-6181 is a practical OE-style solution when you need a rear hub assembly that matches the original application requirements.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Honda Civic\u003c\/li\u003e\n\u003cli\u003eOE-spec replacement focused on form, fit, and function\u003c\/li\u003e\n\u003cli\u003eBall bearing type for rear hub service\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eMagnetic encoder in seal for ABS sensor function\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Honda Civic, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6181 is engineered for foreign nameplate vehicles and sourced through a global network to match the original equipment requirements of the application. For drivers and technicians servicing a Honda Civic rear hub, this assembly provides the correct bearing type, lug count, and ABS encoder style needed for a proper replacement. This part number, 051-6181, is a direct-fit option for 2006-2011 Honda Civic rear wheel bearing and hub assembly service.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by encoder-related hub wear\u003c\/li\u003e\n\u003cli\u003eUneven rear wheel hub operation on a Honda Civic\u003c\/li\u003e\n\u003cli\u003eReplacement after bearing or hub seal deterioration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2006-2011 Honda Civic, rear. The axle nut is not included, so confirm the existing hardware condition before beginning service. Verify the ABS encoder style and rear hub configuration against the original part before installation. Use proper torque procedures and follow the vehicle service manual for bearing and hub replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are selected to meet OE specifications for foreign nameplate applications, with sourcing support from global partners to help ensure the correct fit and function for the Honda Civic rear hub assembly.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305899701,"sku":"BBGB-051-6181","price":131.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516181_Oth.jpg?v=1774710549"},{"product_id":"beck-arnley-051-6183-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6183 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Honda Odyssey\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6183 is a rear wheel bearing and hub assembly for 1999-2004 Honda Odyssey models. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the rear hub service on this application.\u003c\/p\u003e\u003cp\u003eCompatible with 1999-2004 Honda Odyssey rear axle service, this assembly uses a ball bearing design, 5-lug wheel mounting, and an external tone wheel ABS setup. Beck Arnley 051-6183 is a practical choice when you need a rear hub assembly matched to the original vehicle configuration.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Honda Odyssey\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for 1999-2004 Honda Odyssey rear applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for this hub assembly design\u003c\/li\u003e\n\u003cli\u003e5-lug wheel mounting pattern\u003c\/li\u003e\n\u003cli\u003eExternal tone wheel ABS sensor type\u003c\/li\u003e\n\u003cli\u003eGeneration 2 design\u003c\/li\u003e\n\u003cli\u003ePart number: 051-6183\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6183 is engineered for the rear position on 1999-2004 Honda Odyssey models. Beck Arnley sources parts to meet foreign nameplate OE specifications, so the assembly follows the original form, fit, and function expected for this vehicle platform. For shoppers searching for a rear wheel bearing and hub assembly for Honda Odyssey, this part number provides a direct-fit service option for the specified years.\u003c\/p\u003e\u003cp\u003eThis assembly includes a ball bearing design, 5-lug configuration, and external tone wheel ABS sensor type. The axle nut is not included, so confirm your existing hardware before beginning the repair. If you are replacing a worn rear hub on a Honda Odyssey, Beck Arnley 051-6183 is built around the original application requirements.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise from the Honda Odyssey\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the rear hub\u003c\/li\u003e\n\u003cli\u003eABS warning light concerns related to the rear tone wheel setup\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from a failing rear bearing assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1999-2004 Honda Odyssey, rear. Verify the ABS sensor style and 5-lug hub configuration before installation. The axle nut is not included, so plan to reuse or source the correct nut separately if needed. Always inspect the mating surfaces, axle condition, and surrounding suspension components during hub replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305932469,"sku":"BBGB-051-6183","price":118.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516183_Oth.jpg?v=1774710549"},{"product_id":"beck-arnley-051-6188-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6188 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub for MR2 Spyder\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6188 is a front wheel bearing and hub assembly for the 2000-2005 Toyota MR2 Spyder. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the front hub service on this application.\u003c\/p\u003e\u003cp\u003eFor Toyota MR2 Spyder front wheel bearing and hub assembly replacement, this part number 051-6188 matches the vehicle’s OE-style requirements and uses a ball bearing design with a 4-lug hub pattern.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for 2000-2005 Toyota MR2 Spyder\u003c\/li\u003e\n\u003cli\u003eOE-spec replacement from Beck Arnley\u003c\/li\u003e\n\u003cli\u003eBall bearing type\u003c\/li\u003e\n\u003cli\u003e4-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eEnd cap sensor type\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003ePart number 051-6188 for accurate ordering and lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6188 is engineered for the front position on the Toyota MR2 Spyder and follows OE specifications for fit and function. The assembly is specified with a ball bearing type, 4-lug wheel mounting, and an end cap sensor type, making it a direct-match service part for front hub replacement on 2000-2005 Toyota MR2 Spyder models. Beck Arnley sources parts through a global network focused on foreign nameplate applications, helping ensure the replacement aligns with the original vehicle design. If you are searching for a front wheel bearing and hub assembly for Toyota MR2 Spyder 2000-2005, 051-6188 is the correct reference to use.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the front wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel support at the front axle\u003c\/li\u003e\n\u003cli\u003eABS-related service needs when the end cap sensor style is required\u003c\/li\u003e\n\u003cli\u003eRestoration of proper wheel mounting on a 4-lug Toyota MR2 Spyder front hub\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible With 2000-2005 Toyota MR2 Spyder, front. Verify the axle nut requirement before installation, as the axle nut is not included. Confirm the hub orientation, sensor style, and lug pattern against the removed part before pressing or bolting the assembly into place. For best results, inspect related front suspension and axle components during service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That OE-focused approach supports confident replacement selection for the Toyota MR2 Spyder front wheel bearing and hub assembly.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388305965237,"sku":"BBGB-051-6188","price":194.17,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516188_Oth.jpg?v=1774710549"},{"product_id":"beck-arnley-051-6200-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6200 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub for Honda Civic\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6200 is a rear wheel bearing and hub assembly for 1996-2000 Honda Civic models with anti-lock brakes. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the rear hub service on this application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1996-2000 Honda Civic, rear, with anti-lock brakes\u003c\/li\u003e\n\u003cli\u003eWheel bearing and hub assembly with BALL bearing type\u003c\/li\u003e\n\u003cli\u003e4-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eExternal tone wheel ABS sensor type\u003c\/li\u003e\n\u003cli\u003e2nd generation design\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6200\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6200 is engineered for the rear axle on Honda Civic models from 1996 through 2000 that use anti-lock brakes. The assembly follows OE-style specifications for fit and function, and the external tone wheel ABS sensor setup matches the listed application. This part number, 051-6200, is a practical choice when replacing a worn rear hub on a Honda Civic with a 4-lug wheel pattern.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel noise or rumbling that increases with speed\u003c\/li\u003e\n\u003cli\u003eExcessive play in the rear hub area\u003c\/li\u003e\n\u003cli\u003eABS warning light related to the rear wheel speed signal\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation or rough bearing feel\u003c\/li\u003e\n\u003cli\u003eHub wear on a 1996-2000 Honda Civic, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, model, and anti-lock brake configuration before installation. The axle nut is not included, so reuse or source the correct nut separately as required for the vehicle. Confirm the ABS tone wheel style and inspect related components during service to ensure proper operation after replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley sources parts to meet foreign nameplate OE specifications for form, fit, and function. The 051-6200 is backed by that application-focused sourcing approach, helping ensure the rear wheel bearing and hub assembly matches the requirements of the listed Honda Civic fitment.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306030773,"sku":"BBGB-051-6200","price":65.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516200_Oth.jpg?v=1774710551"},{"product_id":"beck-arnley-051-6203-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6203 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Mazda 3\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6203 is a front wheel bearing and hub assembly for select 2004-2005 Mazda 3 models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the original front hub assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for Mazda 3 applications\u003c\/li\u003e\n\u003cli\u003eOE-style fit and function based on foreign nameplate specifications\u003c\/li\u003e\n\u003cli\u003eSupports accurate wheel mounting and smooth hub operation\u003c\/li\u003e\n\u003cli\u003ePart number 051-6203 for easy identification\u003c\/li\u003e\n\u003cli\u003eFits 2004 Mazda 3, front\u003c\/li\u003e\n\u003cli\u003eFits 2005 Mazda 3, front, to 1\/1\/05\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6203 is engineered as a direct replacement wheel bearing and hub assembly for the front axle on select Mazda 3 vehicles. Beck Arnley sources parts through a global network to match the original equipment requirements for fit and function, helping ensure the replacement aligns with the vehicle’s factory specifications. This part number 051-6203 is a practical choice when servicing a front hub on a 2004 Mazda 3 or a 2005 Mazda 3 built to 1\/1\/05.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by worn hub components\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from the front wheel end\u003c\/li\u003e\n\u003cli\u003eService replacement for a worn Mazda 3 front hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify vehicle build date before ordering, since 2005 Mazda 3 fitment applies only to vehicles built to 1\/1\/05. Axle nut is not included, so confirm the existing hardware condition before installation. Always compare the original part to Beck Arnley 051-6203 and follow factory service procedures for torque and bearing installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That OE-focused approach helps support accurate replacement selection for Mazda 3 front hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306129077,"sku":"BBGB-051-6203","price":124.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516203_Oth.jpg?v=1774710552"},{"product_id":"beck-arnley-051-6208-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6208 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub for Toyota Sienna\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6208 is a rear wheel bearing and hub assembly for select 1998-2003 Toyota Sienna models. It is built to foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for rear hub service on this application.\u003c\/p\u003e\u003cp\u003eFor shoppers searching for a rear wheel bearing hub assembly for 1998-2003 Toyota Sienna, Beck Arnley 051-6208 provides the correct fitment details and OE-style construction for confident replacement work.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Toyota Sienna applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for this hub assembly design\u003c\/li\u003e\n\u003cli\u003e4-lug wheel pattern\u003c\/li\u003e\n\u003cli\u003eABS sensor type: ABS sensor\u003c\/li\u003e\n\u003cli\u003eGeneration 2 configuration\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6208\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eCompatible With 1998-2003 Toyota Sienna, rear. This part is specified for rear axle service on the Toyota Sienna and is listed with an axle nut not included note. Beck Arnley 051-6208 is a practical choice when replacing a worn rear hub on a 1998-2003 Toyota Sienna and when matching OE-style dimensions and function matters.\u003c\/p\u003e\u003cp\u003eBeck Arnley sources parts through a global network and focuses on foreign nameplate applications, so the replacement matches the expected fit and operating characteristics for the vehicle platform. This makes Beck Arnley 051-6208 a relevant search match for rear wheel bearing hub assembly replacement on Toyota Sienna rear axle applications.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise from a worn hub assembly\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the rear axle\u003c\/li\u003e\n\u003cli\u003eABS-related wheel speed signal issues at the hub\u003c\/li\u003e\n\u003cli\u003eUneven hub rotation or rough bearing feel\u003c\/li\u003e\n\u003cli\u003eReplacement needs after hub wear on Toyota Sienna rear service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year and position before installation. Confirm the ABS sensor configuration matches the vehicle setup, and note that the axle nut is not included. Use proper torque procedures during installation and inspect related rear suspension and brake components while the hub is removed.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are built to meet foreign nameplate OE specifications for form, fit, and function. That OE-focused approach supports accurate replacement selection for 1998-2003 Toyota Sienna rear hub service, including Beck Arnley 051-6208.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306161845,"sku":"BBGB-051-6208","price":205.86,"currency_code":"USD","in_stock":true}]},{"product_id":"beck-arnley-051-6238-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6238 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for VW and Audi\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 051-6238 rear wheel bearing and hub assembly is built for foreign nameplate OE specifications, with form, fit, and function aligned to the original application. It is a direct replacement choice for rear hub service on select Volkswagen Golf, GTI, Jetta, e-Golf, Golf SportWagen, Beetle, and Audi A3 models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBall bearing design for rear hub service\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eMagnetic encoder in seal for ABS signal integration\u003c\/li\u003e\n\u003cli\u003eGeneration 2 hub assembly design\u003c\/li\u003e\n\u003cli\u003eCompatible with select rear applications on Volkswagen and Audi vehicles\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6238\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Fit and Function\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6238 is sourced to meet foreign nameplate OE specifications, giving technicians a replacement rear wheel bearing and hub assembly that matches the original mounting and operating requirements. This part number 051-6238 is used on rear applications for 2006-2021 Volkswagen Golf, GTI, Jetta, e-Golf, Golf SportWagen, and Beetle, plus 2006-2020 Audi A3 and 2016-2018 Audi A3 Sportback e-tron. It is also a practical choice when servicing rear wheel noise, hub wear, or ABS-related concerns on Volkswagen Golf and Audi A3 platforms.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2019-2021 Volkswagen Golf, rear; 30mm; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2010-2014 Volkswagen Golf, rear; 30mm; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2015-2021 Volkswagen GTI, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2006-2009 Volkswagen GTI, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Volkswagen Jetta, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2011-2013 Volkswagen Jetta, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2015-2020 Audi A3, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2006-2013 Audi A3, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2015-2019 Volkswagen e-Golf, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2015-2019 Volkswagen Golf SportWagen, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2018 Audi A3 Sportback e-tron, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2015-2018 Volkswagen Golf, rear\u003c\/li\u003e\n\u003cli\u003eFits 2013-2015 Volkswagen Jetta, rear; standard suspension; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2011 Volkswagen Jetta, rear; standard suspension; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2010-2014 Volkswagen GTI, rear; 30mm; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Volkswagen Beetle, rear; standard suspension; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2006 Volkswagen Golf, rear; axle nut is not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive hub play or looseness\u003c\/li\u003e\n\u003cli\u003eABS warning light concerns related to the encoder signal\u003c\/li\u003e\n\u003cli\u003eUneven rear wheel rotation caused by hub wear\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support on VW and Audi platforms\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, model, and suspension notes before installation. This assembly uses a magnetic encoder in the seal, so inspect the ABS sensor path and related components during service. Axle nut is not included on listed applications, and some fitments specify a 30mm axle nut requirement. Confirm torque specifications and rear suspension configuration for the exact vehicle before final assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to foreign nameplate OE specifications for form, fit, and function. The brand works with global sourcing partners to help ensure the replacement matches the original application requirements for Volkswagen and Audi rear hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306325685,"sku":"BBGB-051-6238","price":165.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516238_Oth.jpg?v=1774710556"},{"product_id":"beck-arnley-051-6240-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6240 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Audi A4\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6240 is a rear wheel bearing and hub assembly built to foreign nameplate OE specifications for form, fit, and function. It is a direct-fit replacement for select Audi A4 models and is engineered for confident installation on the rear axle.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Audi A4 applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for smooth wheel rotation\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eExternal tone wheel ABS sensor type\u003c\/li\u003e\n\u003cli\u003e2nd generation design\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Audi A4, rear, without bolt; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2004-2009 Audi A4, rear, with bolt; axle nut not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Fit and Construction\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6240 is sourced to match the original equipment requirements used on select Audi A4 rear hub applications. The ball bearing design, 5-lug pattern, and external tone wheel ABS sensor setup support proper wheel mounting and wheel speed signal operation where equipped. This part number, 051-6240, is a practical choice when replacing a worn rear hub on 2002-2009 Audi A4 models.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play at the hub\u003c\/li\u003e\n\u003cli\u003eABS warning light related to rear wheel speed signal issues\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from a failing rear hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year and note the application detail before ordering: 2002-2003 Audi A4 uses the without-bolt version, while 2004-2009 Audi A4 uses the with-bolt version. Axle nut is not included, so confirm the existing hardware condition during service. Always inspect the mating surfaces, ABS tone wheel area, and related suspension components before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. Global sourcing support helps ensure the replacement matches the intended Audi A4 rear hub application with the correct part number, 051-6240.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306292917,"sku":"BBGB-051-6240","price":134.13,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516240_Oth.jpg?v=1774710557"},{"product_id":"beck-arnley-051-6259-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6259 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Subaru Legacy and Outback\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6259 is a rear wheel bearing and hub assembly built to meet foreign nameplate OE specifications for form, fit, and function. It is a direct-fit service part for 2005-2009 Subaru Legacy and 2005-2009 Subaru Outback rear applications, with an axle nut included for the listed fitments.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Subaru Legacy and Subaru Outback\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for foreign nameplate applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for the specified vehicle platform\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003e3rd generation design\u003c\/li\u003e\n\u003cli\u003eAxle nut included for the listed Subaru Legacy and Outback rear applications\u003c\/li\u003e\n\u003cli\u003eABS sensor cord not included\u003c\/li\u003e\n\u003cli\u003ePart number: 051-6259\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6259 is engineered for rear driveline service on 2005-2009 Subaru Legacy and 2005-2009 Subaru Outback models. Beck Arnley sources parts to OE specifications so the assembly matches the required form, fit, and function for the application. This rear hub assembly uses a ball bearing design, a 5-lug pattern, and a generation 3 configuration to support proper wheel-end service on the specified Subaru vehicles. If you are replacing a worn rear hub on a Subaru Legacy or Subaru Outback, this part number 051-6259 provides the correct application-specific replacement.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling from the hub area\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play at the rear axle\u003c\/li\u003e\n\u003cli\u003eRough or inconsistent wheel rotation\u003c\/li\u003e\n\u003cli\u003eHub wear affecting rear wheel-end stability\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged rear hub assembly on Subaru Legacy and Outback models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year and model before installation. This assembly is listed for 2005-2009 Subaru Legacy, rear, and 2005-2009 Subaru Outback, rear. Confirm the axle nut specification for the vehicle and follow factory service procedures for hub removal, bearing installation, and torque sequence. Because the ABS sensor cord is not included, inspect the vehicle’s existing ABS-related components during service and transfer or replace related parts as needed based on the vehicle’s condition.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The brand works with global sourcing partners to help ensure the correct replacement part is selected for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306391221,"sku":"BBGB-051-6259","price":149.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516259_Oth.jpg?v=1774710559"},{"product_id":"beck-arnley-051-6260-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6260 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Toyota and Lexus\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6260 is a rear wheel bearing and hub assembly built to foreign nameplate OE specifications for form, fit, and function. It is a direct-fit replacement for select Toyota, Lexus, and Scion rear applications, including RAV4, NX200t, NX300, Corolla iM, and tC models.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eBearing type: ball\u003c\/li\u003e\n\u003cli\u003e5-lug hub design\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eType 2\/E5 configuration\u003c\/li\u003e\n\u003cli\u003eFits select Toyota RAV4 rear applications, including 2006-2015 and 2016-2018 model years\u003c\/li\u003e\n\u003cli\u003eFits select Lexus NX200t, NX300h, and NX300 rear applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eOE-Style Fit and Application Coverage\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6260 is sourced to match the original equipment requirements used on import vehicles, helping ensure the correct form and function at the rear axle. This part is used on 2018-2021 Lexus NX300 rear, 2017-2018 Toyota Corolla iM rear, 2016-2018 Toyota RAV4 rear, 2015-2017 Lexus NX200t rear, 2015-2016 Lexus NX300h rear, 2016 Scion iM rear, 2011-2016 Scion tC rear, 2006-2015 Toyota RAV4 rear, and 2010-2012 Lexus HS250h rear. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel noise caused by a worn bearing\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from the rear axle area\u003c\/li\u003e\n\u003cli\u003eABS-related service concerns when the original rear hub assembly is worn\u003c\/li\u003e\n\u003cli\u003eUneven wheel support from a deteriorated hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment by year, make, model, and position before installation. Some 2006-2015 Toyota RAV4 applications may require ABS harness verification; check the catalog notes before ordering. Axle nut is not included. Inspect the mounting surface, fasteners, and surrounding brake components during service, and follow the vehicle service manual for torque specifications and bearing installation procedures.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are selected to meet OE specifications for foreign nameplate vehicles, with sourcing support from global partners to help ensure the correct replacement part for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306423989,"sku":"BBGB-051-6260","price":157.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516260_Oth.jpg?v=1774710559"},{"product_id":"beck-arnley-051-6276-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6276 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eOE-Style Front Wheel Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6276 is a front wheel bearing and hub assembly built to match foreign nameplate OE specifications for form, fit, and function. It is a direct replacement for select Nissan Frontier, Xterra, and Pathfinder applications, plus Suzuki Equator front fitments.\u003c\/p\u003e\u003cp\u003eUse Beck Arnley 051-6276 when you need a front hub assembly with the correct spline count, ABS sensor cord, and integrated ABS sensor ring for the listed vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for driveline and axle service\u003c\/li\u003e\n\u003cli\u003eTaper bearing design\u003c\/li\u003e\n\u003cli\u003e29-spline hub configuration\u003c\/li\u003e\n\u003cli\u003e6-lug wheel pattern with M12 wheel studs\u003c\/li\u003e\n\u003cli\u003eWheel studs included\u003c\/li\u003e\n\u003cli\u003eABS sensor cord included\u003c\/li\u003e\n\u003cli\u003eABS sensor ring included\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eOE-spec fitment focus for foreign nameplate vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6276 is engineered for front axle service on 2005-2019 Nissan Frontier, 2005-2015 Nissan Xterra, 2005-2012 Nissan Pathfinder, and 2009-2012 Suzuki Equator. It is built around the application-specific hub dimensions, 29-spline interface, 6-lug wheel mounting, and ABS sensor cord layout required by these platforms. For buyers searching for a front wheel bearing and hub assembly for Nissan Frontier, Nissan Xterra, or Nissan Pathfinder, this part number provides a direct OE-style replacement path.\u003c\/p\u003e\u003cp\u003eBeck\/Arnley sources parts to meet foreign nameplate OE specifications, helping ensure the replacement matches the original form, fit, and function expected on the vehicle. Part number 051-6276 is a practical choice for front hub service where the ABS sensor cord and sensor ring are part of the assembly design.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eABS warning light concerns related to the hub sensor assembly\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the front hub\u003c\/li\u003e\n\u003cli\u003eVibration or instability from a worn hub assembly\u003c\/li\u003e\n\u003cli\u003eService replacement for damaged front hub mounting surfaces\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle’s front application, spline count, lug pattern, and ABS connector style before installation. Axle nut is not included for the listed fitments, so reuse or source the correct axle nut separately as required by the vehicle service procedure. Inspect the mating surfaces, axle splines, and ABS wiring condition during installation to help ensure proper fit and sensor operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet OE specifications for foreign nameplate vehicles, and the brand works with global sourcing partners to supply the correct replacement part for the application. This focus supports accurate fitment for Beck Arnley 051-6276 on the listed Nissan and Suzuki front hub applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306489525,"sku":"BBGB-051-6276","price":186.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516276_Oth.jpg?v=1774710562"},{"product_id":"beck-arnley-051-6291-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6291 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing Hub for Prius\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6291 is a front wheel bearing and hub assembly for select Toyota Prius models. It is built to match foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the front hub service on 2004-2009 Toyota Prius applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2004-2009 Toyota Prius, front\u003c\/li\u003e\n\u003cli\u003eBeck Arnley 051-6291 wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eBall bearing design for front hub service\u003c\/li\u003e\n\u003cli\u003e5-lug hub with 5 wheel studs and M12 wheel studs\u003c\/li\u003e\n\u003cli\u003e26-spline hub configuration\u003c\/li\u003e\n\u003cli\u003eAxle nut included for the listed application\u003c\/li\u003e\n\u003cli\u003eABS sensor cord not included; ABS sensor ring not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Beck Arnley wheel bearing and hub assembly is engineered for the front axle on the Toyota Prius and follows OE-style specifications for fit and function. The assembly uses a ball bearing design and a 3rd-generation hub configuration, with 5-lug mounting, 26 splines, and M12 wheel studs to match the listed vehicle application. Beck Arnley 051-6291 is a practical replacement when servicing a worn front hub on a 2004-2009 Toyota Prius.\u003c\/p\u003e\u003cp\u003eBeck Arnley sources parts through a global network focused on foreign nameplate coverage, helping ensure the replacement matches the original application requirements. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or growling from the hub area\u003c\/li\u003e\n\u003cli\u003eExcessive play or looseness in the front wheel assembly\u003c\/li\u003e\n\u003cli\u003eVibration or roughness felt through the front end\u003c\/li\u003e\n\u003cli\u003eHub wear affecting wheel mounting stability\u003c\/li\u003e\n\u003cli\u003eABS-related service needs when replacing the front hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2004-2009 Toyota Prius, front.\u003c\/li\u003e\n\u003cli\u003eConfirm spline count, lug pattern, and stud size before installation.\u003c\/li\u003e\n\u003cli\u003eInspect the axle nut and surrounding hardware during hub replacement.\u003c\/li\u003e\n\u003cli\u003eVerify ABS sensor and ring requirements for the vehicle before assembly.\u003c\/li\u003e\n\u003cli\u003eFollow factory torque specifications and service procedures for the front hub.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet OE specifications for foreign nameplate vehicles, with attention to form, fit, and function. Part number 051-6291 is built for the listed Prius front hub application and is backed by Beck Arnley’s OE-focused sourcing standards.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306555061,"sku":"BBGB-051-6291","price":115.26,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516291_Oth.jpg?v=1774710564"},{"product_id":"beck-arnley-051-6308-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6308 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Hyundai\u003c\/h2\u003e\u003cp\u003eThe Beck Arnley 051-6308 rear wheel bearing and hub assembly is built for foreign nameplate applications that call for OE-style form, fit, and function. It is a direct-fit service part for the rear of select Hyundai Genesis and Hyundai Equus models, with a ball bearing design and 5-lug hub configuration.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Hyundai applications\u003c\/li\u003e\n\u003cli\u003eBall bearing type for smooth wheel rotation and load support\u003c\/li\u003e\n\u003cli\u003e5-lug hub pattern\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003cli\u003eAxle nut included for the listed applications\u003c\/li\u003e\n\u003cli\u003eBeck Arnley 051-6308 for OE-style replacement service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eCompatible with 2009-2012 Hyundai Genesis, rear, and 2011 Hyundai Equus, rear. This Beck Arnley 051-6308 hub assembly is sourced to match foreign nameplate OE specifications for form, fit, and function, helping maintain proper wheel support and rear-end serviceability on these Hyundai models.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing noise from the rear of the vehicle\u003c\/li\u003e\n\u003cli\u003eExcessive hub play or looseness\u003c\/li\u003e\n\u003cli\u003eRough wheel rotation or bearing wear\u003c\/li\u003e\n\u003cli\u003eRear hub service on Hyundai Genesis or Hyundai Equus\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support after bearing failure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, model, and position before installation. Inspect the axle nut, hub mounting surfaces, and surrounding suspension components during service. Because this assembly is specified for rear applications and includes an axle nut for the listed vehicles, follow the vehicle service procedure and torque specifications for the exact model being repaired.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced through global partners to meet foreign nameplate OE specifications for form, fit, and function. That sourcing approach supports confident installation on the listed Hyundai Genesis and Hyundai Equus rear applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306587829,"sku":"BBGB-051-6308","price":215.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516308_Oth.jpg?v=1774710566"},{"product_id":"beck-arnley-051-6342-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6342 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Infiniti and Nissan\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6342 is a front wheel bearing and hub assembly built to match foreign nameplate OE specifications for form, fit, and function. It is a direct-fit replacement for select Infiniti and Nissan front applications, including Infiniti Q50, Q60, Q70, QX50, QX70, G37, and Nissan 370Z models.\u003c\/p\u003e\u003cp\u003eFor buyers searching for a front wheel bearing and hub assembly for 2009-2020 Nissan 370Z or a front hub assembly for 2014-2022 Infiniti Q50, Beck Arnley 051-6342 provides the OE-style dimensions and mounting details needed for a proper repair.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-spec replacement for foreign nameplate applications\u003c\/li\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for select Infiniti and Nissan vehicles\u003c\/li\u003e\n\u003cli\u003e5-wheel-stud hub design with M12 wheel studs\u003c\/li\u003e\n\u003cli\u003eWheel studs included\u003c\/li\u003e\n\u003cli\u003eNo ABS sensor ring included\u003c\/li\u003e\n\u003cli\u003eAxle nut not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6342\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6342 is engineered for front hub service where correct fitment and OE-style construction matter. Beck Arnley sources parts through a global network to meet foreign nameplate specifications, helping ensure the replacement matches the original form, fit, and function expected on Infiniti and Nissan driveline applications. This part number 051-6342 is used on a wide range of front-wheel applications, including Infiniti Q50, Q60, Q70, QX50, QX70, G37, and Nissan 370Z models.\u003c\/p\u003e\u003cp\u003eThis front wheel bearing and hub assembly is a practical choice when servicing worn hub components on vehicles that rely on precise wheel mounting and bearing support. It is built with M12 wheel studs and includes the studs, while the ABS sensor ring is not included. The axle nut is also not included, so verify all required service parts before beginning the repair.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eWheel play caused by hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or looseness from a worn front hub assembly\u003c\/li\u003e\n\u003cli\u003eDamaged or corroded wheel stud mounting points\u003c\/li\u003e\n\u003cli\u003eOE-fit replacement needs on Infiniti and Nissan front suspension service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm front position and exact vehicle application before installation.\u003c\/li\u003e\n\u003cli\u003eVerify axle nut availability, since it is not included.\u003c\/li\u003e\n\u003cli\u003eInspect the ABS tone ring and related sensor components before reassembly, as no ABS sensor ring is included.\u003c\/li\u003e\n\u003cli\u003eCheck wheel stud thread size and hub seating surfaces during installation.\u003c\/li\u003e\n\u003cli\u003eFollow factory torque specifications for hub, axle, and wheel fasteners.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. Part number 051-6342 is built for direct replacement use on confirmed Infiniti and Nissan front hub applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306653365,"sku":"BBGB-051-6342","price":154.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516342_Oth_248da66f-2946-4798-b0d8-1fa7df080ad0.jpg?v=1774710571"},{"product_id":"beck-arnley-051-6350-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6350 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Toyota\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6350 is a rear wheel bearing and hub assembly built to foreign nameplate OE specifications for form, fit, and function. It is a direct-fit option for select Toyota Camry, Avalon, and Solara models without anti-lock brakes.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Toyota applications\u003c\/li\u003e\n\u003cli\u003eBALL bearing type for the specified OE-style configuration\u003c\/li\u003e\n\u003cli\u003e5-lug hub design\u003c\/li\u003e\n\u003cli\u003eGeneration 3 construction\u003c\/li\u003e\n\u003cli\u003eABS sensor cord not included on this application\u003c\/li\u003e\n\u003cli\u003eCompatible with 1995-1996 Toyota Avalon, 1996-2001 Toyota Camry, and 1999-2003 Toyota Solara rear positions\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6350 is engineered for rear axle service on select Toyota vehicles where an OE-matching replacement is needed. Beck Arnley sources parts through a global network to match foreign nameplate specifications, helping ensure the correct fit and function for the application. This rear hub assembly is listed for 1995-1996 Toyota Avalon, 1996-2001 Toyota Camry, and 1999-2003 Toyota Solara, all in the rear position and without anti-lock brakes. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel support from a worn hub assembly\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged rear hub on Toyota Camry, Avalon, or Solara\u003c\/li\u003e\n\u003cli\u003eRestoration of proper rear wheel mounting on 5-lug applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, model, and brake configuration before installation. This assembly is for vehicles without anti-lock brakes, and the axle nut is not included. Confirm the hub matches the vehicle’s rear OE layout and inspect related components for wear during service. Beck Arnley 051-6350 should be installed according to factory procedures for the specific Toyota application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The brand’s global sourcing approach is intended to provide a correct-match replacement for the listed Toyota Camry, Avalon, and Solara rear applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306718901,"sku":"BBGB-051-6350","price":117.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516350_Oth.jpg?v=1774710572"},{"product_id":"beck-arnley-051-6368-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6368 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Murano\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6368 is a rear wheel bearing and hub assembly built for foreign nameplate OE specifications for form, fit, and function. It is a direct-fit service part for 2003-2007 Nissan Murano rear applications, with an axle nut included and a 5-lug, ball bearing design.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2003-2007 Nissan Murano, rear\u003c\/li\u003e\n\u003cli\u003eBeck Arnley 051-6368 wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eOE-style form, fit, and function for import vehicle service\u003c\/li\u003e\n\u003cli\u003eBall bearing type for rear hub replacement\u003c\/li\u003e\n\u003cli\u003e5-lug hub configuration\u003c\/li\u003e\n\u003cli\u003eAxle nut included\u003c\/li\u003e\n\u003cli\u003eGeneration 3 design\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6368 is engineered for rear hub service on the Nissan Murano, covering 2003, 2004, 2005, 2006, and 2007 models. Beck Arnley sources parts to match foreign nameplate OE specifications, helping ensure the correct fit and function for the application. This rear wheel bearing and hub assembly uses a ball bearing design and a 5-lug hub layout, making it a practical replacement when servicing wheel-end wear on a Nissan Murano rear axle. The part number 051-6368 is also useful when cross-checking catalog listings for the same rear Murano application.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise on a 2003-2007 Nissan Murano\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel end\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eABS-related service needs where the vehicle uses a non-integrated sensor cord configuration\u003c\/li\u003e\n\u003cli\u003eRear hub replacement after mileage-related wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment before ordering by matching the vehicle year, make, and model to the application listing. Verify the 5-lug hub configuration and compare the original part to Beck Arnley 051-6368 before installation. The axle nut is included, but no ABS sensor cord is listed for this part, so inspect the vehicle’s existing sensor setup and related wiring during service. Proper torque procedures and a clean mounting surface are important for final assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That sourcing approach supports accurate replacement selection for import vehicle maintenance and repair.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306784437,"sku":"BBGB-051-6368","price":153.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516368_Oth.jpg?v=1774710574"},{"product_id":"beck-arnley-051-6379-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6379 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6379 is a rear wheel bearing and hub assembly for foreign nameplate applications that require OE-style form, fit, and function. It is built for direct replacement service on select Hyundai Accent and Kia Rio models, with fitment coverage for 2012-2017 vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for OE-style replacement\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Hyundai Accent, rear\u003c\/li\u003e\n\u003cli\u003eFits 2012-2017 Kia Rio, rear\u003c\/li\u003e\n\u003cli\u003eAxle nut is not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6379 for application-specific lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis hub assembly is engineered for foreign nameplate vehicles and sourced through Beck Arnley’s global partner network to match the required specifications for fit and function. It is a direct-fit rear service part for Hyundai Accent and Kia Rio models from 2012 through 2017, making it a practical choice when replacing a worn or noisy rear hub assembly. The part number 051-6379 is useful when confirming the correct rear wheel bearing and hub assembly for these applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play at the hub\u003c\/li\u003e\n\u003cli\u003eRough rotation from a worn bearing assembly\u003c\/li\u003e\n\u003cli\u003eABS or hub-related service issues tied to a failing rear assembly\u003c\/li\u003e\n\u003cli\u003eRestoration of proper rear wheel support on Hyundai Accent and Kia Rio models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. The axle nut is not included, so confirm whether the existing hardware can be reused or if a separate replacement is required for the service. Always inspect the surrounding suspension and brake components during hub replacement, and follow the vehicle manufacturer’s torque specifications and service procedures.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The 051-6379 rear wheel bearing and hub assembly is backed by Beck Arnley’s application-focused sourcing approach for Hyundai Accent and Kia Rio service work.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306849973,"sku":"BBGB-051-6379","price":159.92,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516379_Oth.jpg?v=1774710575"},{"product_id":"beck-arnley-051-6398-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6398 Wheel Bearing and Hub Assembly - Front Left","description":"\u003ch2\u003eFront Left Wheel Bearing Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6398 is a front left wheel bearing and hub assembly for select Lexus applications. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for service work on the front left side.\u003c\/p\u003e\u003cp\u003eCompatible with 2006-2015 Lexus IS250, 2006-2015 Lexus IS350, 2007-2011 Lexus GS350, 2007-2011 Lexus GS450h, 2008-2011 Lexus GS460, 2006-2007 Lexus GS430, and 2006 Lexus GS300, front left. Axle nut is not included.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFront left wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for select Lexus rear-wheel-drive and hybrid sedan applications\u003c\/li\u003e\n\u003cli\u003eBuilt to match foreign nameplate OE specifications for form, fit, and function\u003c\/li\u003e\n\u003cli\u003eDirect replacement for service on the front left hub and bearing location\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6398\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Information\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6398 is sourced through a global network to match the original equipment requirements used on select Lexus models. This wheel bearing and hub assembly is specified for the front left position on Lexus IS250, IS350, GS350, GS450h, GS460, GS430, and GS300 applications, helping restore proper wheel support and hub operation during front-end repair.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise on Lexus IS250 or IS350\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the front left wheel\u003c\/li\u003e\n\u003cli\u003eVibration or rough rotation from a worn bearing assembly\u003c\/li\u003e\n\u003cli\u003eService replacement after hub damage or corrosion\u003c\/li\u003e\n\u003cli\u003eRestoration of proper front wheel support on Lexus GS and IS models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and front left position before installation. The axle nut is not included, so confirm the existing hardware condition and source the correct nut separately if needed. Inspect related suspension and brake components during service to ensure the new hub assembly is installed on a clean, damage-free mounting surface.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are selected to meet OE specifications for foreign nameplate vehicles, with product sourcing managed through global partners to support correct fit and function. Beck Arnley 051-6398 is backed by the brand’s OE-focused replacement approach for Lexus front hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306948277,"sku":"BBGB-051-6398","price":212.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516398_Oth.jpg?v=1774710577"},{"product_id":"beck-arnley-051-6405-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6405 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for BMW M5\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6405 is a front wheel bearing and hub assembly for select 2000-2003 BMW M5 models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for the original front hub assembly.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for BMW M5 applications\u003c\/li\u003e\n\u003cli\u003eOE-style fit and function for foreign nameplate vehicles\u003c\/li\u003e\n\u003cli\u003eParaphrases original equipment specifications for proper replacement fit\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6405\u003c\/li\u003e\n\u003cli\u003eCompatible with 2000-2003 BMW M5, front\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6405 is engineered for the front axle position on the 2000, 2001, 2002, and 2003 BMW M5. Beck Arnley sources parts through a global network to match the form, fit, and function expected for import vehicle service, helping restore proper wheel support and hub operation on this BMW M5 front wheel bearing and hub assembly application. If you are replacing a worn front hub on a BMW M5, this part number 051-6405 provides a direct OE-style service part for the listed fitment.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the front wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from a worn front hub assembly\u003c\/li\u003e\n\u003cli\u003eService replacement for a damaged BMW M5 front hub\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2000-2003 BMW M5, front. The fitment notes state that the axle nut is not included, so confirm the existing hardware condition before installation. Verify the vehicle year and front position before ordering Beck Arnley 051-6405.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That OE-focused approach supports consistent replacement quality for BMW M5 service work.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388306981045,"sku":"BBGB-051-6405","price":178.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516405_Oth.jpg?v=1774710578"},{"product_id":"beck-arnley-051-6408-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6408 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Honda and Acura\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6408 is a front wheel bearing and hub assembly built to match foreign nameplate OE specifications for form, fit, and function. It is a direct-fit replacement for select Honda Pilot, Acura MDX, and Acura ZDX applications, with the correct 30-spline design, M14 wheel studs, and five wheel studs included.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style wheel bearing and hub assembly for front axle service\u003c\/li\u003e\n\u003cli\u003e30-spline hub design\u003c\/li\u003e\n\u003cli\u003eM14 wheel stud size with five wheel studs included\u003c\/li\u003e\n\u003cli\u003eABS sensor ring not included\u003c\/li\u003e\n\u003cli\u003eFlange bolts not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6408\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2009-2015 Honda Pilot, front; axle nut is not included.\u003c\/li\u003e\n\u003cli\u003eFits 2007-2013 Acura MDX, front; axle nut is not included.\u003c\/li\u003e\n\u003cli\u003eFits 2010-2013 Acura ZDX, front; axle nut is not included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBuilt for front-wheel service on select Honda and Acura vehicles, Beck Arnley 051-6408 follows OE specifications to help restore proper hub support and wheel mounting integrity. This assembly is a strong match for drivers searching for a front wheel bearing and hub assembly for 2009-2015 Honda Pilot, 2007-2013 Acura MDX, or 2010-2013 Acura ZDX applications. The 30-spline configuration and M14 stud sizing are important details for correct fitment, and the included wheel studs support a proper hub replacement when the original unit is worn or damaged.\u003c\/p\u003e\u003cp\u003eBeck Arnley sources parts through a global network focused on foreign nameplate applications, which helps ensure the replacement matches the original part’s form and function. If you are replacing a noisy hub, correcting wheel play, or servicing a damaged front hub on a Honda Pilot or Acura MDX, Beck Arnley 051-6408 provides the OE-style dimensions needed for a clean repair.\u003c\/p\u003e\u003ch2\u003eCommon Repair Reasons\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play or looseness\u003c\/li\u003e\n\u003cli\u003eDamaged or worn hub mounting surfaces\u003c\/li\u003e\n\u003cli\u003eBroken or stripped wheel studs\u003c\/li\u003e\n\u003cli\u003eFront-end vibration related to hub wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm front axle fitment before installation and verify the axle nut requirement, since the axle nut is not included. Check the ABS sensor setup on the vehicle, as the ABS sensor ring is not included. Inspect related components such as the knuckle, axle, and mounting surfaces during service to help ensure a proper repair. Beck Arnley 051-6408 should be matched to the exact vehicle application listed above before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That OE-focused approach supports accurate replacement selection for Honda and Acura front hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307013813,"sku":"BBGB-051-6408","price":109.26,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516408_Oth.jpg?v=1774710578"},{"product_id":"beck-arnley-051-6412-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6412 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Nissan\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6412 is a rear wheel bearing and hub assembly built to meet foreign nameplate OE specifications for form, fit, and function. It is a direct-fit replacement for select Nissan Rogue, Nissan Juke, and Rogue Select applications, including rear axle service where precise hub support matters.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Nissan vehicles\u003c\/li\u003e\n\u003cli\u003eOE-style fit and function for foreign nameplate applications\u003c\/li\u003e\n\u003cli\u003eEngineered for 2011-2020 Nissan Rogue, Juke, and Rogue Select rear positions\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6412 for catalog and service matching\u003c\/li\u003e\n\u003cli\u003eAxle nut is not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6412 is a rear wheel bearing and hub assembly for 2013-2020 Nissan Rogue, 2011-2017 Nissan Juke, 2014-2015 Nissan Rogue Select, and 2012 Nissan Rogue from 6\/12. Beck Arnley sources parts to OE specifications so the replacement matches the original form, fit, and function expected on these Nissan driveline and axle applications. If you are searching for a rear wheel bearing and hub assembly for Nissan Rogue or Nissan Juke, this part number provides a direct service option.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear hub noise or rough bearing operation\u003c\/li\u003e\n\u003cli\u003eWheel play caused by worn hub support\u003c\/li\u003e\n\u003cli\u003eVibration from a deteriorated rear bearing assembly\u003c\/li\u003e\n\u003cli\u003eService replacement for rear axle hub wear on Nissan Rogue and Nissan Juke models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm rear fitment by year, model, and build date before ordering. The axle nut is not included, so reuse or source the correct nut separately as required by the vehicle service procedure. Always follow factory torque specifications and inspect related rear suspension and axle components during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet OE specifications for foreign nameplate vehicles, with product selection supported by global sourcing partners and application-focused cataloging. Beck Arnley 051-6412 is intended to provide the correct rear hub and bearing replacement for the listed Nissan applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307079349,"sku":"BBGB-051-6412","price":167.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516412_Oth.jpg?v=1774710579"},{"product_id":"beck-arnley-051-6458-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6458 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Nissan Altima\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6458 is a rear wheel bearing and hub assembly for select Nissan Altima models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear hub service on the 2013-2018 Nissan Altima.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for the Nissan Altima\u003c\/li\u003e\n\u003cli\u003eOE-style replacement built to foreign nameplate specifications\u003c\/li\u003e\n\u003cli\u003eSupports proper form, fit, and function for the application\u003c\/li\u003e\n\u003cli\u003ePart number 051-6458 for easy identification\u003c\/li\u003e\n\u003cli\u003eCompatible with 2013-2018 Nissan Altima rear applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6458 is engineered for rear hub service on the 2013-2018 Nissan Altima. Beck Arnley works with global sourcing partners to supply parts that align with OE expectations, helping you select a rear wheel bearing and hub assembly that matches the original application requirements. If you are searching for a rear wheel bearing and hub assembly for Nissan Altima 2013-2018, this part number provides a direct reference for the correct fitment.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise from wear or damage\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed signal issues related to hub wear\u003c\/li\u003e\n\u003cli\u003eUneven rear wheel rotation caused by bearing deterioration\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support on a Nissan Altima\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2013-2018 Nissan Altima, rear. The axle nut is not included, so verify the existing hardware before beginning service. Confirm the vehicle year and rear application before installation, and compare the original part number 051-6458 to ensure the correct replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307112117,"sku":"BBGB-051-6458","price":163.92,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516458_Oth.jpg?v=1774710584"},{"product_id":"beck-arnley-051-6473-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6473 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6473 is a front wheel bearing and hub assembly for select Toyota full-size trucks and SUVs. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for front-end service on Toyota Sequoia and Toyota Tundra applications.\u003c\/p\u003e\u003cp\u003eCompatible With 2007-2021 Toyota Tundra, front, and 2008-2021 Toyota Sequoia, front. Fits 2022 Toyota Sequoia, front. Axle nut is not included.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement for front hub and bearing service\u003c\/li\u003e\n\u003cli\u003eBuilt to match foreign nameplate OE requirements for fit and function\u003c\/li\u003e\n\u003cli\u003eApplication-specific for Toyota Sequoia and Toyota Tundra front positions\u003c\/li\u003e\n\u003cli\u003eAxle nut not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6473\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis front wheel bearing and hub assembly is used on Toyota Sequoia and Toyota Tundra models where the hub and bearing unit is serviced as a complete assembly. Beck Arnley sources parts through a global network to help ensure the replacement matches the original equipment specification for the listed vehicles. If you are replacing a worn front hub on a 2007-2021 Toyota Tundra or a 2008-2022 Toyota Sequoia, 051-6473 is the correct front-position part for those applications.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFront wheel noise or growl from a worn bearing\u003c\/li\u003e\n\u003cli\u003eExcessive play or looseness at the wheel hub\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed signal issues related to hub wear\u003c\/li\u003e\n\u003cli\u003eUneven tire wear caused by hub or bearing deterioration\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from the front hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, make, model, and front position before installation. Inspect the axle nut and related fasteners during service, since the axle nut is not included with this part. Confirm proper torque specifications and check for any damage to the knuckle, axle, or surrounding components before completing the repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. Part number 051-6473 is backed by Beck Arnley’s application-focused sourcing approach for Toyota Sequoia and Toyota Tundra front hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307144885,"sku":"BBGB-051-6473","price":232.44,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516473_Oth.jpg?v=1774710586"},{"product_id":"beck-arnley-051-6474-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6474 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eOE-Style Front Wheel Bearing Hub\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6474 is a front wheel bearing and hub assembly built for foreign nameplate applications that call for OE-level form, fit, and function. It is a direct replacement for select Toyota Sequoia and Toyota Tundra front positions, with the correct 36-spline design and M14 wheel studs for a proper service replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for select Toyota Sequoia and Toyota Tundra applications\u003c\/li\u003e\n\u003cli\u003e36-spline hub design\u003c\/li\u003e\n\u003cli\u003eM14 wheel studs with 5-stud wheel mounting pattern\u003c\/li\u003e\n\u003cli\u003eWheel studs included\u003c\/li\u003e\n\u003cli\u003eFlange bolts included\u003c\/li\u003e\n\u003cli\u003e4 flange bolts specified\u003c\/li\u003e\n\u003cli\u003eABS sensor ring not included\u003c\/li\u003e\n\u003cli\u003eAxle nut not included on listed fitments\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6474 is engineered for front hub service on 2007-2021 Toyota Tundra and 2008-2021 Toyota Sequoia, with 2022 Toyota Sequoia coverage also listed. The assembly is sourced to match foreign nameplate OE specifications for fit and function, helping restore proper wheel support and hub operation during repair. If you are replacing a worn Toyota Tundra front wheel bearing hub assembly or a Toyota Sequoia front hub assembly, this part number provides the correct application details for a confident match.\u003c\/p\u003e\u003cp\u003eThis part cross-references no listed alternate part numbers in the provided data.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel support at the front axle\u003c\/li\u003e\n\u003cli\u003eDamaged or worn wheel stud mounting points\u003c\/li\u003e\n\u003cli\u003eService replacement after hub wear or contamination\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCompatible With 2022 Toyota Sequoia, front; axle nut not included.\u003c\/li\u003e\n\u003cli\u003eCompatible With 2008-2021 Toyota Sequoia, front; axle nut not included.\u003c\/li\u003e\n\u003cli\u003eCompatible With 2007-2021 Toyota Tundra, front; axle nut not included.\u003c\/li\u003e\n\u003cli\u003eVerify spline count, stud size, and flange bolt pattern before installation.\u003c\/li\u003e\n\u003cli\u003eInspect the axle nut, mating surfaces, and surrounding suspension components during hub replacement.\u003c\/li\u003e\n\u003cli\u003eConfirm ABS system requirements, since the ABS sensor ring is not included.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The 051-6474 hub assembly is built for direct-fit service on the listed Toyota Sequoia and Toyota Tundra front applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307177653,"sku":"BBGB-051-6474","price":220.92,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516474_Oth.jpg?v=1774710586"},{"product_id":"beck-arnley-051-6476-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6476 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Subaru\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6476 is a rear wheel bearing and hub assembly for select Subaru applications. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear hub service on Crosstrek, Impreza, Forester, and XV Crosstrek models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Subaru vehicles\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for form, fit, and function\u003c\/li\u003e\n\u003cli\u003eApplication-specific replacement for rear driveline and axle service\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6476\u003c\/li\u003e\n\u003cli\u003eFits 2021 Subaru Crosstrek, rear; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2021 Subaru Impreza, rear; axle nut not included\u003c\/li\u003e\n\u003cli\u003eFits 2016-2020 Subaru Crosstrek, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2012-2020 Subaru Impreza, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2014-2018 Subaru Forester, rear; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2013-2015 Subaru XV Crosstrek, rear; axle nut is not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6476 is a rear wheel bearing and hub assembly engineered for foreign nameplate vehicles that require OE-level dimensional accuracy and function. For Subaru Crosstrek, Subaru Impreza, Subaru Forester, and Subaru XV Crosstrek rear applications, this assembly supports a direct repair approach when the original hub and bearing unit shows wear, noise, or looseness. Beck Arnley sources parts through a global network to help ensure the correct fit for the listed applications.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise\u003c\/li\u003e\n\u003cli\u003eHub play or looseness\u003c\/li\u003e\n\u003cli\u003eVibration from a worn rear hub assembly\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed related service tied to hub wear\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support on Subaru Crosstrek, Impreza, Forester, or XV Crosstrek\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, model, and position before installation. This part number 051-6476 is listed for rear applications only, and the axle nut is not included. Inspect related mounting surfaces, fasteners, and surrounding suspension components during service to confirm the repair addresses the source of the concern.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307210421,"sku":"BBGB-051-6476","price":133.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516476_Oth.jpg?v=1774710586"},{"product_id":"beck-arnley-051-6479-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6479 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Nissan Armada\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6479 is a rear wheel bearing and hub assembly for select Nissan Armada models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for rear hub service on 2012-2015 Nissan Armada applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for foreign nameplate applications\u003c\/li\u003e\n\u003cli\u003eEngineered to match original form, fit, and function\u003c\/li\u003e\n\u003cli\u003eFits 2012-2015 Nissan Armada, rear\u003c\/li\u003e\n\u003cli\u003ePart number: 051-6479\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6479 is a rear hub assembly designed for 2012, 2013, 2014, and 2015 Nissan Armada models. Beck Arnley sources parts through a global network to support accurate replacement fitment for import vehicles, helping you restore rear wheel support and hub operation with a part built to OE specifications. If you are searching for a rear wheel bearing and hub assembly for Nissan Armada 2012-2015, this part number 051-6479 is the correct application to review.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eExcessive play at the rear hub\u003c\/li\u003e\n\u003cli\u003eVibration or instability from a worn hub assembly\u003c\/li\u003e\n\u003cli\u003eHub wear that affects wheel support on a Nissan Armada\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2012-2015 Nissan Armada, rear. Axle nut is not included. Verify the vehicle year and rear position before installation, and compare the existing hub assembly to confirm the correct application. Part number 051-6479 should be matched to the vehicle’s rear axle service requirements before assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. That sourcing approach supports consistent replacement quality for Nissan Armada rear hub service.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307275957,"sku":"BBGB-051-6479","price":166.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516479_Oth.jpg?v=1774710587"},{"product_id":"beck-arnley-051-6480-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6480 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Honda Odyssey\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6480 is a front wheel bearing and hub assembly for select 2011-2017 Honda Odyssey models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for front-end driveline service.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for Honda Odyssey applications\u003c\/li\u003e\n\u003cli\u003eOE-style fitment based on foreign nameplate specifications\u003c\/li\u003e\n\u003cli\u003eEngineered for form, fit, and function alignment with the original part\u003c\/li\u003e\n\u003cli\u003eBacked by Beck Arnley global sourcing and product support\u003c\/li\u003e\n\u003cli\u003ePart number 051-6480 for accurate ordering and catalog lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6480 is a front wheel bearing and hub assembly for 2011-2017 Honda Odyssey vehicles. Beck Arnley sources parts through a global network and matches foreign nameplate OE requirements so the replacement installs with the correct dimensions and operating characteristics. If you need a front wheel bearing and hub assembly for a Honda Odyssey, part number 051-6480 is a direct catalog reference for the specified application.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eHub wear that affects wheel support at the front axle\u003c\/li\u003e\n\u003cli\u003eVibration or looseness from a worn bearing assembly\u003c\/li\u003e\n\u003cli\u003eService replacement after hub or bearing damage\u003c\/li\u003e\n\u003cli\u003eRestoring proper front wheel support on a Honda Odyssey\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eCompatible With 2011-2017 Honda Odyssey, front. Axle nut is not included. Verify the vehicle year and front position before installation, and confirm the original part matches the application listed for Beck Arnley 051-6480.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet OE specifications for foreign nameplate vehicles, with attention to fit and function for the listed application. Part number 051-6480 is cataloged for the front wheel bearing and hub assembly use shown above.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307472565,"sku":"BBGB-051-6480","price":118.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516480_Oth.jpg?v=1774710587"},{"product_id":"beck-arnley-051-6481-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6481 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Acura MDX\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6481 is a rear wheel bearing and hub assembly for select 2014-2016 Acura MDX models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear driveline service.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Acura MDX applications\u003c\/li\u003e\n\u003cli\u003eOE-style fit and function for foreign nameplate vehicles\u003c\/li\u003e\n\u003cli\u003eEngineered for direct replacement service\u003c\/li\u003e\n\u003cli\u003ePart number 051-6481 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6481 is made for rear hub and bearing service on the 2014, 2015, and 2016 Acura MDX. Beck Arnley sources parts through a global network to match the original equipment specifications needed for proper fit and dependable installation. If you are replacing a worn rear wheel bearing and hub assembly on an Acura MDX, this part provides a straightforward OE-style solution.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eWheel play caused by hub wear\u003c\/li\u003e\n\u003cli\u003eVibration from a worn rear hub assembly\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed signal issues related to hub wear\u003c\/li\u003e\n\u003cli\u003eUneven rear wheel rotation from bearing damage\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2014-2016 Acura MDX, rear. Verify the axle nut requirement before installation, since the axle nut is not included. Confirm the vehicle year and rear position before ordering, and inspect related suspension and driveline components during service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. Part number 051-6481 is backed by Beck Arnley’s application-focused sourcing approach for import vehicle repair.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307538101,"sku":"BBGB-051-6481","price":115.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516481_Oth.jpg?v=1774710587"},{"product_id":"beck-arnley-051-6486-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6486 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Nissan\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6486 is a front wheel bearing and hub assembly for select Nissan full-size trucks and SUVs. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement for front-end service on the Nissan Armada and Nissan TITAN.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for select Nissan applications\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for form, fit, and function\u003c\/li\u003e\n\u003cli\u003eEngineered for 2012-2015 Nissan Armada, front\u003c\/li\u003e\n\u003cli\u003eEngineered for 2012-2015 Nissan TITAN, front\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6486\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6486 is sourced through a global network of partners to match the specifications expected on foreign nameplate vehicles. For drivers and technicians servicing a Nissan Armada or Nissan TITAN, this front wheel bearing and hub assembly provides a direct replacement option for restoring proper wheel support and hub operation. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing noise during driving\u003c\/li\u003e\n\u003cli\u003eWheel hub play or looseness at the front axle\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by worn hub components\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed concerns related to hub wear\u003c\/li\u003e\n\u003cli\u003eFront-end vibration tied to bearing or hub deterioration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2012-2015 Nissan Armada, front. Fits 2012-2015 Nissan TITAN, front. Axle nut is not included, so confirm the existing hardware condition before installation. Verify the vehicle year, model, and front axle configuration before ordering, and follow factory service procedures for hub removal, torque, and bearing installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are selected to meet OE specifications for foreign nameplate vehicles, with product specialists working with global sourcing partners to support correct fit and dependable service on the intended application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307636405,"sku":"BBGB-051-6486","price":160.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516486_Oth.jpg?v=1774710588"},{"product_id":"beck-arnley-051-6490-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6490 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Honda HR-V\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6490 is a rear wheel bearing and hub assembly for select Honda HR-V models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear hub service on the 2016-2022 Honda HR-V.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Honda HR-V applications\u003c\/li\u003e\n\u003cli\u003eOE-style fitment and dimensions for foreign nameplate vehicles\u003c\/li\u003e\n\u003cli\u003eEngineered to match original form, fit, and function requirements\u003c\/li\u003e\n\u003cli\u003eBacked by Beck Arnley global sourcing and product support\u003c\/li\u003e\n\u003cli\u003ePart number 051-6490 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6490 is a rear hub assembly made for 2016-2022 Honda HR-V models. Beck Arnley sources parts to OE specifications so the replacement matches the original application requirements for the Honda HR-V rear wheel bearing and hub assembly. If you are servicing a noisy, worn, or loose rear hub on a Honda HR-V, this part number 051-6490 provides a direct-fit replacement path.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286) for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a worn rear wheel bearing and hub assembly on a Honda HR-V\u003c\/li\u003e\n\u003cli\u003eCorrecting rear wheel noise caused by bearing wear\u003c\/li\u003e\n\u003cli\u003eAddressing wheel play or looseness at the rear hub\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support and rotation\u003c\/li\u003e\n\u003cli\u003eServicing a damaged hub assembly on 2016-2022 Honda HR-V models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible With 2016-2022 Honda HR-V, rear. Axle nut is not included, so verify the existing hardware condition before installation. Confirm the vehicle year and rear position against the part number 051-6490 before ordering, and follow Honda service procedures for hub and bearing replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to meet foreign nameplate OE specifications for form, fit, and function. The brand works with global sourcing partners to help ensure the correct replacement part is selected for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307734709,"sku":"BBGB-051-6490","price":156.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516490_Oth.jpg?v=1774710589"},{"product_id":"beck-arnley-051-6491-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6491 Wheel Bearing and Hub Assembly - Front","description":"\u003ch2\u003eFront Wheel Bearing and Hub Assembly for Nissan\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6491 is a front wheel bearing and hub assembly for select Nissan applications. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for common front-end service on the Nissan NV200, Sentra, and LEAF.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFront wheel bearing and hub assembly for OE-style replacement\u003c\/li\u003e\n\u003cli\u003eFits 2013-2019 Nissan NV200, front; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2013-2019 Nissan Sentra, front; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eFits 2013-2017 Nissan LEAF, front; axle nut is not included\u003c\/li\u003e\n\u003cli\u003eBeck Arnley part number 051-6491 for application-specific lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Application Coverage\u003c\/h2\u003e\u003cp\u003eThis Beck Arnley wheel bearing and hub assembly is sourced to match the original equipment specifications used on foreign nameplate vehicles. For shoppers searching for a front wheel bearing and hub assembly for Nissan NV200, Sentra, or LEAF models, 051-6491 provides a direct-fit service part for the front position. This part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Service Issues\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFront wheel noise or growling from a worn bearing\u003c\/li\u003e\n\u003cli\u003eExcessive hub play or looseness at the wheel\u003c\/li\u003e\n\u003cli\u003eABS or wheel-speed related service concerns tied to hub wear\u003c\/li\u003e\n\u003cli\u003eUneven tire wear caused by bearing or hub instability\u003c\/li\u003e\n\u003cli\u003eVibration or rough rotation from a damaged front hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify year, model, and front-position fitment before installation. The axle nut is not included, so confirm the existing hardware condition and replace any worn related components as needed. Always follow factory torque specifications and service procedures for the Nissan NV200, Sentra, or LEAF.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley parts are sourced to OE specifications for foreign nameplate vehicles, with product specialists working with global sourcing partners to help ensure the correct fit and function for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307767477,"sku":"BBGB-051-6491","price":132.91,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516491_Oth.jpg?v=1774710589"},{"product_id":"beck-arnley-051-6492-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6492 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing and Hub Assembly for Toyota Sienna\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6492 is a rear wheel bearing and hub assembly for select Toyota Sienna models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear hub service on the 2011-2020 Toyota Sienna.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Toyota Sienna applications\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for form, fit, and function\u003c\/li\u003e\n\u003cli\u003eSource-backed by Beck Arnley global sourcing partners\u003c\/li\u003e\n\u003cli\u003ePart number 051-6492 for accurate ordering and lookup\u003c\/li\u003e\n\u003cli\u003eCompatible with 2011-2020 Toyota Sienna, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6492 is a rear wheel bearing and hub assembly engineered for foreign nameplate vehicles that require OE-level dimensional accuracy. For drivers and repair shops servicing a Toyota Sienna rear hub, this assembly supports a straightforward replacement path when the original bearing or hub shows wear, noise, or looseness. The Beck Arnley 051-6492 application coverage includes 2011-2020 Toyota Sienna, rear, and the axle nut is not included.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise on a Toyota Sienna\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eVibration or rough rotation from a worn rear bearing\u003c\/li\u003e\n\u003cli\u003eService replacement after hub or bearing wear\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support on 2011-2020 Toyota Sienna models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by model year before installation. Inspect the mating surfaces, fasteners, and surrounding suspension components for wear or damage during service. The axle nut is not included, so confirm the correct hardware is on hand before beginning the repair. Use proper torque procedures for the vehicle and follow factory service information.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley sources parts to foreign nameplate OE specifications and works with global sourcing partners to help ensure the correct fit for the application. Part number 051-6492 is intended for direct replacement use on listed Toyota Sienna rear applications.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307800245,"sku":"BBGB-051-6492","price":163.55,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516492_Oth.jpg?v=1774710589"},{"product_id":"beck-arnley-051-6493-wheel-bearing-and-hub-assembly","title":"Beck Arnley 051-6493 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eBeck Arnley Rear Wheel Bearing Hub Assembly\u003c\/h2\u003e\u003cp\u003eBeck Arnley 051-6493 is a rear wheel bearing and hub assembly for select Fiat 500 models. It is built to meet foreign nameplate OE specifications for form, fit, and function, giving you a direct replacement option for rear hub service on the Fiat 500.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Fiat 500 applications\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for foreign nameplate vehicles\u003c\/li\u003e\n\u003cli\u003eEngineered to match original form, fit, and function requirements\u003c\/li\u003e\n\u003cli\u003eAxle nut included for the listed application\u003c\/li\u003e\n\u003cli\u003ePart number 051-6493 for ordering and catalog lookup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eFits 2012-2019 Fiat 500, rear.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286) for the same application.\u003c\/p\u003e\u003cp\u003eFor Fiat 500 rear hub replacement, 051-6493 provides a direct OE-spec replacement path. It is a practical choice when servicing wheel bearing noise, hub wear, or rear-end driveline looseness on 2012-2019 Fiat 500 models.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Addresses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eHub play or looseness at the rear wheel\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by worn hub components\u003c\/li\u003e\n\u003cli\u003eABS-related concerns when the hub assembly is worn\u003c\/li\u003e\n\u003cli\u003eRear axle service requiring a replacement hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year before ordering. Inspect the mating surfaces, axle components, and related hardware during installation, and follow the vehicle service procedure for torque specifications and bearing seating. The included axle nut applies to the listed Fiat 500 rear application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eBeck Arnley sources parts through a global network focused on foreign vehicle OE specifications, helping ensure the replacement matches the required form, fit, and function for the application.\u003c\/p\u003e","brand":"Beck Arnley","offers":[{"title":"Default Title","offer_id":43388307833013,"sku":"BBGB-051-6493","price":136.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/BA_0516493_Oth.jpg?v=1774710590"},{"product_id":"moog-512003-wheel-bearing-and-hub-assembly","title":"Moog 512003 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for GM Applications\u003c\/h2\u003e\u003cp\u003eThe MOOG 512003 rear wheel bearing and hub assembly is built for select Buick, Cadillac, Chevrolet, Oldsmobile, and Pontiac vehicles that need a precise rear hub replacement. It combines application-specific dimensions with an integrated ABS sensor for straightforward service on vehicles such as the Buick LeSabre, Cadillac DTS, and Pontiac Bonneville.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select GM platforms\u003c\/li\u003e\n\u003cli\u003eAnti-lock brake sensor included for ABS-equipped applications\u003c\/li\u003e\n\u003cli\u003eFlange bolt hole quantity: 4\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 5\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 115.000 mm \/ 4.530 in.\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 150.500 mm\u003c\/li\u003e\n\u003cli\u003eFlange offset: 64.800 mm\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 70.100 mm\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 70.600 mm\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 71.800 mm\u003c\/li\u003e\n\u003cli\u003eRectangular flange shape for application-specific fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eMOOG 512003 is a rear wheel bearing and hub assembly engineered for direct replacement on a range of GM rear-wheel applications. It is listed for 2006-2011 Buick Lucerne rear, 2006-2011 Cadillac DTS rear, 2000-2005 Buick LeSabre rear, 1997-2005 Buick Park Avenue rear, 2000-2005 Cadillac DeVille rear without Heavy Duty Suspension, and 2000-2005 Pontiac Bonneville rear. Additional fitments include the Cadillac Seville, Oldsmobile Aurora, Chevrolet Malibu, Pontiac Grand Am, Buick Riviera, Oldsmobile Cutlass, Cadillac Allante, Cadillac Eldorado, Oldsmobile Toronado, and Buick Reatta in rear positions.\u003c\/p\u003e\u003cp\u003eBuilt with durable materials and tested for consistent performance, this hub assembly supports proper wheel mounting, bearing operation, and ABS signal integration. This part cross-references SKF (e.g., BR930074, BR930471) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eWheel play caused by hub wear\u003c\/li\u003e\n\u003cli\u003eABS warning light concerns related to a failing hub sensor\u003c\/li\u003e\n\u003cli\u003eUneven wheel mounting from a worn hub flange\u003c\/li\u003e\n\u003cli\u003eVibration or instability from degraded rear hub components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear-position fitment and confirm the vehicle does not have Heavy Duty Suspension when servicing a 2000-2005 Cadillac DeVille. Match the bolt circle, pilot diameters, and flange dimensions to the original hub before installation. Inspect the mating surfaces, axle area, and ABS connector condition during replacement to help ensure proper seating and sensor operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG hub assemblies are backed by tested materials and application-focused engineering for dependable service. The 512003 is built to meet the dimensional and functional requirements of the listed rear applications, including ABS-equipped vehicles.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422773870773,"sku":"FLLJ-512003","price":158.59,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512003_Fro.jpg?v=1774732246"},{"product_id":"moog-512014-wheel-bearing-and-hub-assembly","title":"Moog 512014 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub for Nissan 240SX\u003c\/h2\u003e\u003cp\u003eMOOG 512014 is a rear wheel bearing and hub assembly for select 1989-1998 Nissan 240SX models. It is built with MOOG design updates that focus on longer service life and easier installation and replacement, making it a practical OE-style choice for rear hub service.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 1989-1998 Nissan 240SX\u003c\/li\u003e\n\u003cli\u003eFlange bolt hole quantity: 4\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 84.000\u003c\/li\u003e\n\u003cli\u003eAnti-lock brake sensor not included\u003c\/li\u003e\n\u003cli\u003eMOOG part number 512014 for rear driveline and axle repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eThis MOOG wheel bearing and hub assembly is engineered for the rear position on the Nissan 240SX and is suited for drivers replacing a worn hub, noisy bearing, or damaged mounting surface. The 4-bolt flange and 84.000 hub pilot diameter support a direct-fit service approach on 1989-1998 Nissan 240SX rear applications. MOOG 512014 is also referenced by cross numbers such as SKF GRW261 and Mevotech Supreme H512014 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1989-1998 Nissan 240SX, rear. Compatible With 1989-1998 Nissan 240SX rear hub and bearing replacement service. Compatible With 1989-1998 Nissan 240SX rear wheel bearing assembly repair.\u003c\/p\u003e\u003ch2\u003eCommon Reasons to Replace\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or rough rotation\u003c\/li\u003e\n\u003cli\u003eExcessive play in the hub assembly\u003c\/li\u003e\n\u003cli\u003eDamaged or worn hub mounting surfaces\u003c\/li\u003e\n\u003cli\u003eABS-related service where the sensor is not part of the assembly\u003c\/li\u003e\n\u003cli\u003eRestoring proper rear wheel support on a Nissan 240SX\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year before ordering, since this part is specific to 1989-1998 Nissan 240SX applications. Confirm the flange bolt hole count and hub pilot diameter match the original component, and transfer any vehicle-specific ABS components as needed because the sensor is not included. For best results, inspect related rear suspension and axle components during hub replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG is known for ongoing design improvements that help extend product life and simplify service work. Part number 512014 reflects that approach with a rear hub assembly built for straightforward replacement on the Nissan 240SX platform.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422773969077,"sku":"FLLJ-512014","price":150.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512014_Fro.jpg?v=1774732247"},{"product_id":"moog-512153-wheel-bearing-and-hub-assembly","title":"Moog 512153 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Hub Assembly for Corvette and XLR\u003c\/h2\u003e\u003cp\u003eMOOG 512153 is a rear wheel bearing and hub assembly built for 1997-2008 Chevrolet Corvette and 2004-2008 Cadillac XLR applications. It combines OE-style fitment details with MOOG materials and testing standards to support consistent wheel-end performance and straightforward service work.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Chevrolet Corvette and Cadillac XLR\u003c\/li\u003e\n\u003cli\u003eIncludes an ABS sensor for vehicles that use integrated wheel speed sensing\u003c\/li\u003e\n\u003cli\u003e30-spline hub design with a triangular flange shape\u003c\/li\u003e\n\u003cli\u003e5 wheel studs and 3 flange bolt holes for the specified application\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 91.300 mm\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 70.100 mm\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 70.600 mm\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 120.700 mm \/ 4.750 in\u003c\/li\u003e\n\u003cli\u003eFlange offset: 42.100 mm and flange diameter: 145.500 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eMOOG 512153 is engineered as a rear hub assembly for the Chevrolet Corvette and Cadillac XLR, with dimensions and mounting geometry matched to the listed applications. The integrated ABS sensor supports wheel speed signal function, while the hub and flange measurements help maintain proper alignment at the wheel end. MOOG’s problem-solving design approach focuses on reducing installation friction and supporting a clean service fit on the rear suspension.\u003c\/p\u003e\u003cp\u003eThis part cross-references SKF BR930198 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or roughness\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by a failed hub sensor assembly\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the rear hub\u003c\/li\u003e\n\u003cli\u003eUneven wheel-end rotation from worn bearing components\u003c\/li\u003e\n\u003cli\u003eService issues tied to incorrect hub dimensions or bolt pattern mismatch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. Confirm the ABS connector routing and sensor interface match the original setup on 1997-2008 Chevrolet Corvette and 2004-2008 Cadillac XLR rear applications. Check flange bolt pattern, hub pilot diameter, and brake pilot diameter against the removed part to ensure proper seating and alignment. Clean the mounting surface and inspect related wheel-end components before reassembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG backs this hub assembly with superior materials and rigorous testing to support reliable service life and consistent performance in the specified rear applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422774263989,"sku":"FLLJ-512153","price":188.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512153_Fro.jpg?v=1774732247"},{"product_id":"moog-512175-wheel-bearing-and-hub-assembly","title":"Moog 512175 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly\u003c\/h2\u003e\u003cp\u003eMoog 512175 is a rear wheel bearing and hub assembly built for 2001-2005 Acura EL and 2001-2005 Honda Civic applications. It combines hub and bearing service in one assembly and includes an ABS sensor for direct replacement on the rear axle.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for Acura EL and Honda Civic\u003c\/li\u003e\n\u003cli\u003eIncludes anti-lock brake sensor\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 4\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 56.000\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 61.000\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 66.000\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 139.000\u003c\/li\u003e\n\u003cli\u003eFlange offset: 56.000\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 102.000 \/ 3.940\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eMoog 512175 is engineered as a rear hub assembly for 2001-2005 Honda Civic and 2001-2005 Acura EL vehicles. MOOG focuses on design updates that improve service life and make replacement easier, which is why this hub assembly is built for straightforward rear-wheel service and consistent fitment on the listed applications. This part cross-references SKF BR930255 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Help Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or growling\u003c\/li\u003e\n\u003cli\u003eExcessive hub play or looseness\u003c\/li\u003e\n\u003cli\u003eABS warning light related to the rear wheel speed sensor\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or roughness from a worn rear hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. Confirm the ABS sensor connection and compare the hub dimensions, bolt circle, and pilot diameters to the original part. Clean the mounting surface and inspect related brake and suspension components during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG is known in chassis and driveline service for ongoing design improvements that support longer part life and easier installation. Part number 512175 is built to meet the listed rear application requirements for Acura EL and Honda Civic models.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422774395061,"sku":"FLLJ-512175","price":96.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512175_Fro.jpg?v=1774732248"},{"product_id":"moog-512179-wheel-bearing-and-hub-assembly","title":"Moog 512179 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for Acura and Honda\u003c\/h2\u003e\u003cp\u003eMOOG 512179 is a rear wheel bearing and hub assembly built for select Acura and Honda applications. It combines a precision hub design with an integrated ABS sensor to support stable wheel rotation and consistent brake system signal output.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select 1998-2006 Acura and Honda vehicles\u003c\/li\u003e\n\u003cli\u003eIntegrated anti-lock brake sensor included\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 5\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 2.520 in.\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 64.000 mm\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 66.000 mm\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 152.000 mm\u003c\/li\u003e\n\u003cli\u003eFlange offset: 56.000 mm\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 116.000 mm \/ 4.500 in.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eMOOG 512179 is engineered as a direct-fit rear hub assembly for vehicles that need a replacement wheel bearing unit with ABS sensor integration. Backed by durable materials and testing, this hub assembly is built to deliver dependable wheel support and simplify service on rear suspension and brake-related repairs. It is a strong match for drivers searching for a rear wheel bearing and hub assembly for 2002-2006 Acura RSX, 2004-2005 Honda Civic, 1999-2003 Acura TL, or 1998-2002 Honda Accord.\u003c\/p\u003e\u003cp\u003eThis part cross-references SKF BR930071 and Raybestos Brakes 712179 for the same application. MOOG 512179 is also referenced by several OE and aftermarket numbers used on the same rear hub application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2002-2006 Acura RSX, Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2005 Honda Civic, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1999-2003 Acura TL, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1998-2002 Honda Accord, Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing noise or roughness\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by a failing hub sensor\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the rear hub\u003c\/li\u003e\n\u003cli\u003eUneven brake feel related to hub or bearing wear\u003c\/li\u003e\n\u003cli\u003eService replacement for worn rear hub assembly components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. Confirm the bolt circle, pilot diameters, and ABS sensor connection match the original part. Clean the mounting surface thoroughly and inspect adjacent brake and suspension components during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG hub assemblies are built with tested materials and problem-solving design details to support reliable service and easier installation on the specified Acura and Honda rear applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422774984885,"sku":"FLLJ-512179","price":93.21,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512179_Fro_26beff33-d224-4d9d-99d9-6a975544b64a.jpg?v=1774732248"},{"product_id":"moog-512183-wheel-bearing-and-hub-assembly","title":"Moog 512183 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for Subaru\u003c\/h2\u003e\u003cp\u003eMoog 512183 is a rear wheel bearing and hub assembly built for select Subaru applications, including the Subaru Baja, Legacy, and Outback. It combines OE-style fitment with design updates that help simplify replacement and support long service life.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for select Subaru models\u003c\/li\u003e\n\u003cli\u003eFlange bolt hole quantity: 4\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 84.000\u003c\/li\u003e\n\u003cli\u003eFlange offset: 43.000\u003c\/li\u003e\n\u003cli\u003eAnti-lock brake sensor not included\u003c\/li\u003e\n\u003cli\u003eMoog part number 512183\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eMoog 512183 is engineered for rear axle service on 2003-2006 Subaru Baja, 2000-2004 Subaru Legacy, and 2000-2004 Subaru Outback. As part of MOOG hub assemblies, this unit reflects the brand’s focus on design improvements that extend product life and make installation and replacement more straightforward. It is a direct-fit wheel bearing and hub assembly for rear applications where precise hub dimensions and stable wheel mounting are required.\u003c\/p\u003e\u003cp\u003eThis part cross-references Beck\/Arnley 051-6143 and SKF GRW241 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel noise caused by worn hub or bearing components\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the rear axle\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation from bearing wear\u003c\/li\u003e\n\u003cli\u003eHub mounting issues related to flange fitment\u003c\/li\u003e\n\u003cli\u003eReplacement after corrosion or mileage-related wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eFits 2003-2006 Subaru Baja, rear. Fits 2000-2004 Subaru Legacy, rear. Fits 2000-2004 Subaru Outback, rear. Verify flange bolt hole count, hub pilot diameter, and flange offset before installation. This assembly does not include an anti-lock brake sensor, so confirm the vehicle’s sensor arrangement and reuse or replace related components as needed.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG is known in the chassis and driveline market for ongoing design enhancements that improve durability and simplify service. Part number 512183 is built to meet the fitment and dimensional requirements of the listed Subaru rear applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422775279797,"sku":"FLLJ-512183","price":72.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512183_Fro.jpg?v=1774732249"},{"product_id":"moog-512188-wheel-bearing-and-hub-assembly","title":"Moog 512188 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for Acura TL and Honda Accord\u003c\/h2\u003e\u003cp\u003eMOOG 512188 is a rear wheel bearing and hub assembly built for dependable service on select Acura TL and Honda Accord models. It combines a precision hub design with an integrated ABS sensor to support smooth wheel rotation and consistent wheel speed signal output.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2004-2008 Acura TL and 2003-2007 Honda Accord\u003c\/li\u003e\n\u003cli\u003eIntegrated anti-lock brake sensor included\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 5\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 114.300 mm \/ 4.500 in.\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 3.170 in.\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 2.520 in.\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 64.000 mm\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 139.500 mm\u003c\/li\u003e\n\u003cli\u003eFlange offset: 56.000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eMOOG 512188 is engineered with durable materials and tested for reliable performance in everyday driveline service. The hub assembly is built for rear applications on the Acura TL and Honda Accord, with dimensions that support proper wheel mounting and brake interface alignment. This part cross-references SKF BR930383 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing noise from the rear hub area\u003c\/li\u003e\n\u003cli\u003eExcessive wheel play or looseness at the hub\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by a failing wheel speed sensor or hub signal issue\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation caused by worn hub components\u003c\/li\u003e\n\u003cli\u003eVibration or roughness traced to rear bearing wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. Confirm bolt circle, pilot diameters, and flange dimensions against the original part to ensure correct seating and wheel alignment. Because the ABS sensor is included, inspect the connector and wiring path during replacement to avoid signal faults after installation. This part number is MOOG 512188, and it is listed for rear use on 2004-2008 Acura TL and 2003-2007 Honda Accord.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG hub assemblies are backed by material selection and testing practices aimed at consistent performance and dependable fit. MOOG 512188 is part of MOOG’s hub assembly line for rear wheel bearing service on Acura TL and Honda Accord applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422775312565,"sku":"FLLJ-512188","price":98.36,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512188_Fro.jpg?v=1774732249"},{"product_id":"moog-512194-wheel-bearing-and-hub-assembly","title":"Moog 512194 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for Hyundai and Kia\u003c\/h2\u003e\u003cp\u003eMoog 512194 is a rear wheel bearing and hub assembly built for select Hyundai Elantra and Kia Spectra applications. It is specified with the correct pilot diameters, bolt pattern, and flange dimensions for a direct-fit replacement on covered vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2001-2006 Hyundai Elantra, rear\u003c\/li\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2005-2009 Kia Spectra, rear\u003c\/li\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2005-2009 Kia Spectra5, rear\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 4\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 114.300 mm \/ 4.500 in.\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 67.000 mm\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 76.000 mm\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 74.000 mm\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 139.000 mm\u003c\/li\u003e\n\u003cli\u003eFlange offset: 50.500 mm\u003c\/li\u003e\n\u003cli\u003eAnti-lock brake sensor included: No\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eMoog 512194 is a rear hub assembly engineered for precise fitment on select Hyundai Elantra, Kia Spectra, and Kia Spectra5 models. The assembly uses the listed pilot diameters and 4.5-inch bolt circle to match the original mounting geometry, helping maintain proper wheel and brake interface on the rear axle. MOOG focuses on design updates that improve service life and make replacement easier, which is why this part is a practical OE-style choice for driveline and axle service.\u003c\/p\u003e\u003cp\u003eThis part cross-references Timken HA590188 and SKF BR930596K for the same application. Moog 512194 is also referenced under MOOG Hub Assemblies 512194 for catalog matching.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a worn rear wheel bearing and hub assembly on a 2001-2006 Hyundai Elantra\u003c\/li\u003e\n\u003cli\u003eReplacing a rear hub assembly on a 2005-2009 Kia Spectra\u003c\/li\u003e\n\u003cli\u003eReplacing a rear hub assembly on a 2005-2009 Kia Spectra5\u003c\/li\u003e\n\u003cli\u003eAddressing rear wheel play, noise, or rough rotation caused by hub wear\u003c\/li\u003e\n\u003cli\u003eRestoring correct wheel mounting and brake pilot alignment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear fitment by year, make, and model before installation. Confirm the 4-lug bolt pattern, pilot diameters, and flange dimensions against the original part to ensure proper alignment. Because the anti-lock brake sensor is not included, reuse or transfer the vehicle’s existing sensor setup where applicable. Always inspect the mating surfaces, axle area, and brake components during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG is known in chassis and steering service for ongoing design improvements that focus on longer part life and easier installation. Part number 512194 is built to meet the dimensional requirements of the listed Hyundai and Kia rear applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422775410869,"sku":"FLLJ-512194","price":81.33,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512194_Fro.jpg?v=1774732249"},{"product_id":"moog-512206-wheel-bearing-and-hub-assembly","title":"Moog 512206 Wheel Bearing and Hub Assembly - Rear Left","description":"\u003ch2\u003eWheel Bearing Hub Assembly for Toyota and Lexus\u003c\/h2\u003e\u003cp\u003eMOOG 512206 is a rear left wheel bearing and hub assembly built for select Toyota and Lexus applications. It combines a hub assembly design with an integrated anti-lock brake sensor to support accurate wheel speed signal delivery and dependable rear wheel operation.\u003c\/p\u003e\u003cp\u003eCompatible with 2001-2003 Toyota Highlander, rear left; 2002-2011 Toyota Camry, rear left; 2004-2008 Toyota Solara, rear left; 2005-2012 Toyota Avalon, rear left; 2002-2003 Lexus ES300, rear left; 2004-2006 Lexus ES330, rear left; and 2007-2012 Lexus ES350, rear left.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMOOG wheel bearing and hub assembly, part number 512206\u003c\/li\u003e\n\u003cli\u003eRear left position for select Toyota and Lexus vehicles\u003c\/li\u003e\n\u003cli\u003eIntegrated anti-lock brake sensor included\u003c\/li\u003e\n\u003cli\u003eFlange shape: offset trapezoid\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 114.3 mm \/ 4.5 in\u003c\/li\u003e\n\u003cli\u003eWheel stud quantity: 5\u003c\/li\u003e\n\u003cli\u003eFlange bolt hole quantity: 4\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 60.0 mm\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 62.0 mm\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 75.0 mm\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 152.0 mm\u003c\/li\u003e\n\u003cli\u003eFlange offset: 74.5 mm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eMOOG 512206 is engineered as a direct-fit hub assembly for rear left service on Toyota Camry, Avalon, Solara, Highlander, and Lexus ES-series models listed above. MOOG uses quality materials and testing practices to support consistent performance, while the hub design is intended to simplify replacement on vehicles that use an integrated ABS sensor and specific pilot and bolt-circle dimensions. This part cross-references SKF BR930267 and Timken HA592460 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing noise from the rear left corner\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by a failing hub sensor assembly\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the hub\u003c\/li\u003e\n\u003cli\u003eUneven wheel rotation or rough bearing feel\u003c\/li\u003e\n\u003cli\u003eCorrosion or wear at the hub mounting surface\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear left fitment by year, make, and model before ordering. Confirm the bolt circle, pilot diameters, and ABS sensor connection match the original hub assembly on your vehicle. Clean the mounting surface thoroughly and inspect related brake and suspension components during replacement. For Toyota Camry and Lexus ES350 rear left hub replacement, matching the OE-style dimensions helps ensure proper seating and sensor alignment.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG hub assemblies are backed by material selection and testing practices aimed at dependable service life and consistent fit. Part number 512206 is built to meet the dimensional and sensor requirements of the listed Toyota and Lexus rear left applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422776131765,"sku":"FLLJ-512206","price":147.54,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512206_Fro_e158b53b-640e-4a50-92d9-e3ce1ff2340d.jpg?v=1774732250"},{"product_id":"moog-512207-wheel-bearing-and-hub-assembly","title":"Moog 512207 Wheel Bearing and Hub Assembly - Rear Right","description":"\u003ch2\u003eMOOG 512207 Rear Right Hub Assembly\u003c\/h2\u003e\u003cp\u003eMOOG 512207 is a rear right wheel bearing and hub assembly built for select Toyota and Lexus applications. It combines OE-style fitment details with an integrated ABS sensor to support accurate wheel speed signal transfer and straightforward replacement on the vehicle.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing and hub assembly for the rear right position\u003c\/li\u003e\n\u003cli\u003eIntegrated anti-lock brake sensor included\u003c\/li\u003e\n\u003cli\u003e5 wheel studs with a 4-bolt flange design\u003c\/li\u003e\n\u003cli\u003eFlange diameter: 152.000 mm\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 114.300 mm \/ 4.500 in\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 60.000 mm\u003c\/li\u003e\n\u003cli\u003eBrake pilot diameter: 62.000 mm\u003c\/li\u003e\n\u003cli\u003eHub pilot diameter: 75.000 mm\u003c\/li\u003e\n\u003cli\u003eOffset trapezoid flange shape with 74.500 flange offset\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eMOOG 512207 is engineered for rear right wheel bearing and hub replacement on 2001-2003 Toyota Highlander, 2002-2011 Toyota Camry, 2004-2008 Toyota Solara, 2005-2012 Toyota Avalon, 2002-2003 Lexus ES300, 2004-2006 Lexus ES330, and 2007-2012 Lexus ES350. If you are searching for a rear right wheel hub assembly for Toyota Camry, Toyota Avalon, or Lexus ES350 service work, this part number provides the fitment and dimensions needed for a direct repair path. MOOG uses quality materials and testing practices to support dependable operation and installation that follows the vehicle’s original mounting layout.\u003c\/p\u003e\u003cp\u003eThis part cross-references SKF BR930266 and Timken HA592450 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWheel bearing noise from the rear right corner\u003c\/li\u003e\n\u003cli\u003eABS warning light caused by a failed hub sensor\u003c\/li\u003e\n\u003cli\u003eWheel play or looseness at the hub\u003c\/li\u003e\n\u003cli\u003eUneven braking feel related to hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or rumble from a worn rear hub assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify rear right fitment by year, make, and model before installation. Confirm the flange, bolt circle, and pilot dimensions match the original hub assembly, and inspect the mating surfaces, axle area, and brake components during replacement. Because this assembly includes an ABS sensor, check the connector routing and sensor alignment during installation. MOOG 512207 is listed for the rear right position only.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMOOG backs this hub assembly with materials selection and testing focused on reliable performance and consistent fit. The brand’s problem-solving design approach supports a smoother replacement process on the specified Toyota and Lexus applications.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422776230069,"sku":"FLLJ-512207","price":150.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512207_Fro.jpg?v=1774732250"},{"product_id":"moog-512209-wheel-bearing-and-hub-assembly","title":"Moog 512209 Wheel Bearing and Hub Assembly - Rear","description":"\u003ch2\u003eRear Wheel Bearing Hub Assembly for Toyota and Scion\u003c\/h2\u003e\u003cp\u003eMoog 512209 is a rear wheel bearing and hub assembly built for select Toyota and Scion applications. It combines hub, bearing, and ABS sensor integration in one service part for a direct-fit repair on the rear axle.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2000-2005 Toyota Echo, rear\u003c\/li\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2004-2006 Scion xA, rear\u003c\/li\u003e\n\u003cli\u003eRear wheel bearing and hub assembly for 2004-2006 Scion xB, rear\u003c\/li\u003e\n\u003cli\u003eAnti-lock brake sensor included\u003c\/li\u003e\n\u003cli\u003e4 flange bolt holes and 4 wheel studs\u003c\/li\u003e\n\u003cli\u003eOffset trapezoid flange shape with 135.000 flange diameter\u003c\/li\u003e\n\u003cli\u003eBolt circle diameter: 100.000 \/ 3.940\u003c\/li\u003e\n\u003cli\u003eWheel pilot diameter: 54.000; brake pilot diameter: 55.000; hub pilot diameter: 67.000\u003c\/li\u003e\n\u003cli\u003eFlange offset: 54.500\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eMoog 512209 is a rear hub assembly engineered for the Toyota Echo and Scion xA\/xB rear position applications listed above. The assembly includes an ABS sensor and uses the specified hub and pilot dimensions to support proper wheel mounting and brake interface alignment. Moog focuses on design updates that improve service life and make replacement easier, which is useful when replacing a worn rear wheel bearing hub on a Toyota Echo or Scion xB.\u003c\/p\u003e\u003cp\u003eThis part cross-references SKF BR930358 and Timken HA594245 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRear wheel noise caused by a worn hub bearing\u003c\/li\u003e\n\u003cli\u003eABS warning light concerns related to a failing wheel speed sensor circuit\u003c\/li\u003e\n\u003cli\u003eWheel looseness or play at the rear hub\u003c\/li\u003e\n\u003cli\u003eUneven rotor or wheel mounting issues from hub wear\u003c\/li\u003e\n\u003cli\u003eVibration or rough rotation from a deteriorated bearing assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear-position fitment by year, make, and model before installation. Confirm the bolt circle, flange dimensions, and pilot diameters match the original hub assembly on the vehicle. Inspect the mating surfaces, axle area, and brake components during replacement, and follow the vehicle service procedure for ABS sensor connection and torque specifications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eMoog is known for chassis and driveline service parts that incorporate design improvements aimed at extending product life and simplifying replacement. Part number 512209 is built to meet the fitment and dimensional requirements listed for the Toyota Echo and Scion xA\/xB rear hub application.\u003c\/p\u003e","brand":"Moog","offers":[{"title":"Default Title","offer_id":43422776295605,"sku":"FLLJ-512209","price":163.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/MO_512209_Fro.jpg?v=1774732251"}],"url":"https:\/\/www.partcatalog.com\/collections\/hubs-and-related-components.oembed?page=156","provider":"PartCatalog","version":"1.0","type":"link"}