{"title":"Emission Control \u003e Vacuum System","description":"\u003cp\u003eYour vehicle's vacuum system routes engine-generated or pump-generated vacuum to operate emission controls, power brake boosters, HVAC actuators, EGR valves, and dozens of other components. Failures are common on high-mileage engines — dry-rotted hoses crack and collapse, vacuum pumps wear out their vanes or seals (especially on diesel engines where the pump does the heavy lifting), and switching valves stick open or closed. Most vacuum hoses and check valves are inexpensive DIY fixes under $20, while a diesel vacuum pump replacement typically runs $150–$400 in parts. When buying, verify fitment by engine code, not just year\/make\/model — many platforms share body styles but use different vacuum routing. OEM-spec parts are worth the premium for pump rebuilds and switching valves on turbocharged or diesel applications; quality aftermarket hose and connector kits are generally fine for naturally aspirated gas engines.\u003c\/p\u003e\n\n\u003ch3\u003eSigns you need replacement\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHard brake pedal with little stopping power\u003c\/strong\u003e — On vehicles with vacuum-assisted brakes, a failed vacuum pump or collapsed booster hose drastically increases pedal effort. This is a safety issue; don't drive until diagnosed.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRough idle, surging, or stalling\u003c\/strong\u003e — A cracked vacuum hose, failed vacuum regulator valve, or leaking vacuum reservoir introduces unmetered air, throwing off fuel trims and causing erratic idle or hesitation under load.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCheck engine light with EGR, EVAP, or boost-related codes\u003c\/strong\u003e — Vacuum switching valves and diverter valves control solenoid-operated emission devices. A stuck or leaking valve often triggers P0400–P0409 (EGR flow), P0171\/P0174 (lean codes), or boost-related faults on turbocharged engines.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHVAC vents stuck in one position or mode\u003c\/strong\u003e — Many blend door and vent actuators are vacuum-operated. If your defrost or floor\/dash vent selection stops responding, a failed vacuum motor or broken vacuum harness line is a common cause.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWhining or rattling noise from the front of the engine on diesels\u003c\/strong\u003e — Worn vacuum pump vanes or a damaged pulley bearing produce audible noise under load. A pump that's cavitating or losing prime will also show up as intermittent brake assist loss.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHissing sound from the engine bay at idle\u003c\/strong\u003e — A steady hiss points to a split vacuum hose, cracked connector, or failed check valve. Use a vacuum gauge or carb cleaner (carefully) to isolate the leak source before replacing parts blindly.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHow often should vacuum hoses and check valves be replaced?\u003c\/strong\u003e\n  Rubber vacuum hoses typically last 60,000–100,000 miles but degrade faster in high-heat engine bays. Inspect them at every major service — look for cracks, brittleness, or collapsed sections. Proactive replacement during a timing belt or head gasket job saves labor costs later. Check valves have no set interval; replace on symptom or confirmed failure.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eIs OEM worth it for a vacuum pump, or will aftermarket work?\u003c\/strong\u003e\n  For diesel engines (VW TDI, BMW, Mercedes CDI, RAM 2500\/3500 Cummins), the vacuum pump is safety-critical for brake assist — OEM or a reputable aftermarket brand like Pierburg or Febi is recommended. On gas engines where the pump primarily serves emission functions, a quality aftermarket unit is generally reliable and can save $100–$200 over dealer pricing.\u003c\/li\u003e\n\n  \u003cli\u003e\n\u003cstrong\u003eWhat else should I replace when doing a vacuum pump on a diesel?\u003c\/strong\u003e\n  Always replace the pump's oil feed line or banjo bolt sealing washers and the pump gasket — these are common leak points and cheap insurance. If the pump failed due to oil starvation, inspect the cam lobe that drives it. A vacuum pump repair kit covering seals, vanes, and gaskets typically runs $15–$40 and is worth including in any pump job.\u003c\/li\u003e\n\u003c\/ul\u003e","products":[{"product_id":"cardone-64-1012-vacuum-pump","title":"Cardone 64-1012 Vacuum Pump","description":"\u003ch2\u003eCardone Vacuum Pump for Ford Ranger and Bronco II\u003c\/h2\u003e\u003cp\u003eCardone 64-1012 is a remanufactured vacuum pump built for direct replacement on select Ford applications. It is engineered for quick installation, tested for reliable operation, and corrected for original design weaknesses to help deliver consistent performance in service.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e100% computer tested for reliable performance\u003c\/li\u003e\n\u003cli\u003eRemanufactured to meet or exceed O.E.M. performance\u003c\/li\u003e\n\u003cli\u003eDesigned for easy installation\u003c\/li\u003e\n\u003cli\u003eGuaranteed fit and function\u003c\/li\u003e\n\u003cli\u003eInstruction sheet included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThe Cardone Vacuum Pump line focuses on remanufactured replacement parts that restore factory-style operation while addressing known wear points from the original design. Part number 64-1012 is built for drivers and technicians looking for a direct-fit vacuum pump for 1985-1987 Ford Ranger and 1985 Ford Bronco II applications. This part cross-references Ford E5TZ2A451A for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With 1985-1987 Ford Ranger, N\/A vacuum pump and 1985 Ford Bronco II, N\/A vacuum pump. If you are searching for a remanufactured vacuum pump for a Ford Ranger or Ford Bronco II, 64-1012 is the application-specific replacement to review.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part May Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum pump output\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns\u003c\/li\u003e\n\u003cli\u003eReduced accessory or system performance tied to vacuum supply\u003c\/li\u003e\n\u003cli\u003eNoise or irregular operation from a worn pump\u003c\/li\u003e\n\u003cli\u003eFailure caused by internal wear or original design weakness\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eReview the included instruction sheet before installation. Confirm the vehicle application, inspect related vacuum lines and mounting surfaces, and verify that no pulley or mounting bracket is included with this part. Proper system inspection during replacement can help prevent repeat vacuum-related faults.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eEach Cardone remanufactured vacuum pump is computer tested and engineered to meet or exceed O.E.M. performance standards. The remanufacturing process is intended to correct original design weaknesses and provide dependable fit and function for the listed Ford applications.\u003c\/p\u003e","brand":"Cardone","offers":[{"title":"Default Title","offer_id":43387853668533,"sku":"CPCX-64-1012","price":146.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/A1_641012_Fro.jpg?v=1774708033"},{"product_id":"dorman-300-156-vacuum-pump-pulley","title":"Dorman 300-156 Vacuum Pump Pulley","description":"\u003ch2\u003eVacuum Pump Pulley for Ford E-350 Super Duty\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump pulley is a standard replacement part built to match the original fit and function on specified applications. It is made from steel with a black finish for dependable service in the emission control vacuum system.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Dorman\u003c\/li\u003e\n\u003cli\u003ePart number: 300-156\u003c\/li\u003e\n\u003cli\u003eSteel construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eBlack finish\u003c\/li\u003e\n\u003cli\u003eSerpentine belt application\u003c\/li\u003e\n\u003cli\u003eV-belt pulley\/groove design\u003c\/li\u003e\n\u003cli\u003eOutside diameter: 5 in.\u003c\/li\u003e\n\u003cli\u003eWidth: 1.4 in.\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade\u003c\/li\u003e\n\u003cli\u003eDirect replacement for specified Ford applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eDorman 300-156 is a vacuum pump pulley engineered for the emission control vacuum system on select Ford E-350 Super Duty and Ford E-350 Club Wagon models with a heavy duty alternator. It is built to replicate the original pulley’s fit and function, helping maintain proper belt drive operation in the engine accessory system. The steel construction supports long-term durability, while the black finish provides a clean OE-style appearance. If you are replacing a worn or damaged pulley on a Ford E-350 Super Duty, 300-156 is a direct-fit service part for the listed applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Ford 4C2Z2L487BA for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWorn or damaged vacuum pump pulley surfaces\u003c\/li\u003e\n\u003cli\u003eBelt tracking issues related to pulley wear\u003c\/li\u003e\n\u003cli\u003eNoise from a failing pulley in the accessory drive\u003c\/li\u003e\n\u003cli\u003eLoss of proper vacuum pump drive function\u003c\/li\u003e\n\u003cli\u003eService needs on Ford E-350 Super Duty and Ford E-350 Club Wagon models with heavy duty alternator\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify belt type, pulley dimensions, and vehicle configuration before installation. This pulley is listed for 2004-2010 Ford E-350 Super Duty and 2004-2005 Ford E-350 Club Wagon with heavy duty alternator. Confirm the existing vacuum pump and belt routing match the application before service. Professional installation is recommended for proper alignment and drive performance.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman designs this vacuum pump pulley as a standard replacement part for specified OE applications. It is manufactured from quality materials and engineered to match original fit and function for reliable service.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43610862420149,"sku":"BKKY-300-156","price":42.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_300156_Fro.jpg?v=1774983348"},{"product_id":"dorman-300-700-vacuum-pump-pulley","title":"Dorman 300-700 Vacuum Pump Pulley","description":"\u003ch2\u003eVacuum Pump Pulley for Ford Super Duty Applications\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump pulley is a standard replacement for select Ford trucks and vans that use a belt-driven vacuum pump system. Built from steel and engineered to match the original pulley’s fit and function, it supports dependable operation in demanding daily-use and fleet applications.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eSteel construction for strength and wear resistance\u003c\/li\u003e\n\u003cli\u003eDirect replacement for the original vacuum pump pulley on specified applications\u003c\/li\u003e\n\u003cli\u003eStandard replacement grade for routine service repairs\u003c\/li\u003e\n\u003cli\u003eSingle-mount-hole design for OE-style installation alignment\u003c\/li\u003e\n\u003cli\u003eFits select Ford E-350, F-250, and F-350 applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment and Application Details\u003c\/h2\u003e\u003cp\u003eCompatible with select Ford vacuum system applications, this pulley is listed for 2003 Ford E-350 Club Wagon; 1999-2003 Ford E-350 Super Duty; 1999-2003 Ford F-250 Super Duty; 1999-2003 Ford F-350 Super Duty; 1995-2002 Ford E-350 Econoline Club Wagon; 1995-1998 Ford E-350 Econoline; 1997 Ford F-250 HD; 1995-1997 Ford F-350; and 1995-1996 Ford F-250. If you are replacing a worn vacuum pump pulley on a Ford E-350 Super Duty, F-250 Super Duty, or F-350 Super Duty, this Dorman 300-700 is built to match the original part’s fit and function.\u003c\/p\u003e\u003cp\u003eThis part cross-references Ford OE number F5TZ2L487A for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWobbling or noisy vacuum pump pulley operation\u003c\/li\u003e\n\u003cli\u003eWear from belt contact on the original pulley surface\u003c\/li\u003e\n\u003cli\u003eLoss of proper belt drive engagement at the vacuum pump\u003c\/li\u003e\n\u003cli\u003eReplacement after pulley damage, cracking, or deformation\u003c\/li\u003e\n\u003cli\u003eService repair for aging vacuum system components on Ford trucks and vans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify pulley alignment, belt condition, and vacuum pump condition before installation. This Dorman 300-700 does not include installation hardware or instructions, so reuse or source the correct service hardware as needed and follow the vehicle service procedure for your specific Ford application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman engineers this vacuum pump pulley as a fit-and-function replacement using quality materials for reliable performance and durability. It is built to meet standard replacement expectations for service work on select Ford E-350, F-250, and F-350 models.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43610890338485,"sku":"BKKY-300-700","price":44.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_300700_Fro_b418a2f7-cc2d-4414-903c-fc2b49092d62.jpg?v=1774983364"},{"product_id":"dorman-300-701-vacuum-pump-pulley","title":"Dorman 300-701 Vacuum Pump Pulley","description":"\u003ch2\u003eDorman 300-701 Vacuum Pump Pulley\u003c\/h2\u003e\u003cp\u003eThe Dorman 300-701 vacuum pump pulley is a standard replacement part for select Ford applications that use a V-belt drive. Built from steel with a black finish, it is engineered to match the fit and function of the original pulley for dependable service.\u003c\/p\u003e\u003cp\u003eCompatible with Ford E-250 Econoline Club Wagon, E-350 Econoline, E-350 Econoline Club Wagon, F-150, F-250, and F-350 applications, this pulley supports vacuum pump operation in the specified model years. The Dorman 300-701 is a direct-fit replacement for owners servicing emission control and vacuum system components on classic Ford trucks and vans.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteel construction for strength and durability\u003c\/li\u003e\n\u003cli\u003eBlack finish for OE-style appearance\u003c\/li\u003e\n\u003cli\u003eV-belt pulley type with 4.82 in. outside diameter\u003c\/li\u003e\n\u003cli\u003e0.75 in. width for specified applications\u003c\/li\u003e\n\u003cli\u003eStandard replacement part for direct-fit service\u003c\/li\u003e\n\u003cli\u003eDesigned to match original fit and function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis vacuum pump pulley is built for Ford vacuum system service where a V-belt driven pulley is required. The Dorman 300-701 uses steel construction to provide stable belt engagement and consistent operation in the specified emission control setup. It cross-references Ford E9TZ2L487A for the same application.\u003c\/p\u003e\u003cp\u003eFits 1983-1991 Ford E-250 Econoline Club Wagon, N\/A; Fits 1983-1991 Ford E-350 Econoline, N\/A; Fits 1983-1991 Ford E-350 Econoline Club Wagon, N\/A; Fits 1983-1991 Ford F-250, N\/A; Fits 1983-1991 Ford F-350, N\/A; Fits 1984 Ford F-150, N\/A; Fits 1992 Ford E-350 Econoline, N\/A, To 3\/92; Fits 1992 Ford E-350 Econoline Club Wagon, N\/A, To 3\/92; Fits 1992 Ford F-250, N\/A, To 3\/92; Fits 1992 Ford F-350, N\/A, To 3\/92.\u003c\/p\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a worn or damaged vacuum pump pulley\u003c\/li\u003e\n\u003cli\u003eRestoring proper V-belt drive alignment\u003c\/li\u003e\n\u003cli\u003eAddressing belt slip caused by pulley wear\u003c\/li\u003e\n\u003cli\u003eRepairing vacuum system drive issues on Ford vans and trucks\u003c\/li\u003e\n\u003cli\u003eServicing emission control components on listed applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify pulley diameter, width, and belt type before installation. Confirm the vehicle application and production cutoff for 1992 models marked To 3\/92. Inspect the belt, mounting point, and adjacent drive components for wear before completing the repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this pulley as a standard replacement part using quality materials for reliable performance and durability. It is engineered to match the original pulley’s fit and function on the specified Ford applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43610890502325,"sku":"BKKY-300-701","price":56.1,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_300701_Fro.jpg?v=1774983365"},{"product_id":"dorman-300-702-vacuum-pump-pulley","title":"Dorman 300-702 Vacuum Pump Pulley","description":"\u003ch2\u003eVacuum Pump Pulley for GM Applications\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump pulley is a standard replacement for select Chevrolet and GMC vehicles that use a serpentine belt system. Built from steel with a black finish, it is made to match the original pulley’s fit and function for dependable operation on the specified applications.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Dorman\u003c\/li\u003e\n\u003cli\u003ePart number: 300-702\u003c\/li\u003e\n\u003cli\u003eSteel construction for durability\u003c\/li\u003e\n\u003cli\u003eBlack housing color\/finish\u003c\/li\u003e\n\u003cli\u003eSerpentine belt type\u003c\/li\u003e\n\u003cli\u003eSmooth pulley design\u003c\/li\u003e\n\u003cli\u003eOutside diameter: 4.91 in.\u003c\/li\u003e\n\u003cli\u003eWidth: 0.98 in.\u003c\/li\u003e\n\u003cli\u003eStandard replacement item grade\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eDorman 300-702 is a vacuum pump pulley engineered to replicate the original pulley’s fit and function on select GM trucks, vans, and SUVs. It is designed for vehicles including Chevrolet Express 2500, Chevrolet Express 3500, GMC Savana 2500, GMC Savana 3500, and other listed Chevrolet and GMC applications. The steel construction and smooth pulley profile support consistent belt engagement in serpentine drive systems. This part cross-references GM OE part number 15589757 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1996-2002 Chevrolet Express 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2002 Chevrolet Express 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2002 GMC Savana 2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2002 GMC Savana 3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chevrolet C2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chevrolet C3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chevrolet K2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 Chevrolet K3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 GMC C2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 GMC C3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 GMC K2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-2000 GMC K3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet C1500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet C2500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet K1500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet K2500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet P30, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 Chevrolet Tahoe, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC C1500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC C2500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC K1500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC K2500 Suburban, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1999 GMC P3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1998 Chevrolet C1500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1998 Chevrolet K1500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1998 GMC K1500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1997 GMC C1500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1996-1997 GMC Yukon, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet C1500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1995 Chevrolet C1500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet C2500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 Chevrolet C2500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet C3500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet K1500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1995 Chevrolet K1500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet K2500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 Chevrolet K2500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 Chevrolet K3500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1995 Chevrolet Tahoe, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC C1500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1995 GMC C1500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC C2500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 GMC C2500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC C3500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC K1500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1995 GMC K1500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC K2500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 GMC K2500 Suburban, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1988-1995 GMC K3500, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 GMC Yukon, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003cli\u003eFits 1994 Chevrolet Blazer, N\/A, w\/RPO Code C60 (Front Manual Temperature Controls)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a worn or damaged vacuum pump pulley on GM trucks and vans\u003c\/li\u003e\n\u003cli\u003eRestoring proper serpentine belt tracking on the vacuum pump drive\u003c\/li\u003e\n\u003cli\u003eAddressing pulley noise caused by wear, corrosion, or surface damage\u003c\/li\u003e\n\u003cli\u003eCorrecting belt alignment issues related to an out-of-spec pulley\u003c\/li\u003e\n\u003cli\u003eRepairing vacuum pump drive components on Chevrolet and GMC C\/K, Suburban, Tahoe, Yukon, Express, and Savana models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s RPO code and belt system before ordering, especially on 1988-1995 applications with C60 front manual temperature controls. Confirm pulley dimensions, belt type, and mounting configuration against the original part before installation. Dorman 300-702 is a direct-fit replacement for the listed applications and is intended for use with a serpentine belt setup.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this pulley as a standard replacement part using quality materials for reliable service and durability. The design is based on the original pulley’s fit and function for the specified GM applications, including Chevrolet Express, GMC Savana, and related C\/K truck and SUV platforms.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":43610890797237,"sku":"BKKY-300-702","price":107.15,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_300702_Fro_766662ef-2790-4d42-a61d-5f56b1547fc0.jpg?v=1774983365"},{"product_id":"rein-abv0115p-vacuum-hose","title":"Rein ABV0115P Vacuum Hose","description":"\u003ch2\u003eOE Quality Vacuum Hose for Mercedes-Benz\u003c\/h2\u003e\u003cp\u003eRein ABV0115P is an application-specific vacuum hose built to match original equipment design specifications for select Mercedes-Benz vehicles. It is made as a direct-fit replacement with the size, shape, and connector details needed for a clean installation and reliable vacuum routing.\u003c\/p\u003e\u003cp\u003eCompatible With Mercedes-Benz models including the C230, E320, S500, ML320, and CLK500, this Rein vacuum hose supports factory-style fitment across a wide range of 1985-2011 applications. The ABV0115P part number is used for OE-style replacement needs where form, fit, and function matter.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMatches original equipment design specifications.\u003c\/li\u003e\n\u003cli\u003eManufactured with high quality materials.\u003c\/li\u003e\n\u003cli\u003eDirect fit for easier installation.\u003c\/li\u003e\n\u003cli\u003eResistant to heat, salt, road debris, oil, and other contaminants.\u003c\/li\u003e\n\u003cli\u003eApplication-specific design for select Mercedes-Benz vacuum system service.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eRein Automotive OE quality vacuum hoses are engineered for European vehicles and built to mirror the original hose layout used by the manufacturer. The ABV0115P vacuum hose is shaped for proper routing and connection, helping maintain the vacuum system integrity expected on Mercedes-Benz platforms. If you are replacing a worn or damaged hose on a Mercedes-Benz C280, E500, SL500, or G500, this part provides an OE-style solution without altering the factory configuration.\u003c\/p\u003e\u003cp\u003eThis part cross-references URO 1170780281 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCracked or brittle vacuum hose material.\u003c\/li\u003e\n\u003cli\u003eVacuum leaks caused by heat or contamination exposure.\u003c\/li\u003e\n\u003cli\u003ePoor hose fit from non-OE replacement parts.\u003c\/li\u003e\n\u003cli\u003eRouting issues on Mercedes-Benz vacuum system repairs.\u003c\/li\u003e\n\u003cli\u003eService needs on aging hoses in high-mileage vehicles.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify hose routing and connector orientation against the original part before installation. This vacuum hose is application specific and uses a direct-fit design, so it should be matched to the vehicle’s exact engine and vacuum system layout. Inspect nearby vacuum lines, fittings, and related components for wear before completing the repair.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eRein OE quality vacuum hoses are built to OE design standards and manufactured with durable materials for European vehicle applications. Part number ABV0115P includes a 24-month or 24,000-mile warranty.\u003c\/p\u003e\u003ch2\u003eCompatible Mercedes-Benz Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2006-2011 Mercedes-Benz B200, N\/A, 80mm, w\/Belt Driven Starter.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2011 Mercedes-Benz G55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2005-2010 Mercedes-Benz SLK55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006-2009 Mercedes-Benz CLK350, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Mercedes-Benz CLK550, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Mercedes-Benz SLR McLaren, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2002-2008 Mercedes-Benz G500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2008 Mercedes-Benz SL55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2002-2007 Mercedes-Benz C230, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1997-2000 Mercedes-Benz C230, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercedes-Benz C280, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2000 Mercedes-Benz C280, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1996 Mercedes-Benz C280, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercedes-Benz C350, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2002-2007 Mercedes-Benz ML500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercedes-Benz R500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2005-2006 Mercedes-Benz C55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2006 Mercedes-Benz CL500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 Mercedes-Benz CL55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2006 Mercedes-Benz CLK500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 Mercedes-Benz CLK55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006 Mercedes-Benz CLS500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006 Mercedes-Benz CLS55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2006 Mercedes-Benz E500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994 Mercedes-Benz E500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1999-2006 Mercedes-Benz E55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2006 Mercedes-Benz S350, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 Mercedes-Benz S350, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2000-2006 Mercedes-Benz S430, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-2006 Mercedes-Benz S500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2006 Mercedes-Benz S55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-2006 Mercedes-Benz SL500, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2005 Mercedes-Benz C240, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2005 Mercedes-Benz C320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2005 Mercedes-Benz CLK320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-2005 Mercedes-Benz E320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Mercedes-Benz ML350, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Mercedes-Benz C32 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2004 Mercedes-Benz SLK320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1999-2003 Mercedes-Benz CLK430, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2003 Mercedes-Benz ML320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2000-2003 Mercedes-Benz ML55 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 Mercedes-Benz CL600, N\/A, 80mm, w\/Cyl. Cut-Out System.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2002 Mercedes-Benz E430, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-2002 Mercedes-Benz SL600, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1999-2001 Mercedes-Benz ML430, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-2000 Mercedes-Benz C43 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1998-1999 Mercedes-Benz CL600, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1999 Mercedes-Benz E300, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1999 Mercedes-Benz S320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1999 Mercedes-Benz S420, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1999 Mercedes-Benz S600, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1997 Mercedes-Benz E420, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1995 Mercedes-Benz E420, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1997 Mercedes-Benz SL320, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1994-1996 Mercedes-Benz C220, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1995-1996 Mercedes-Benz C36 AMG, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1985-1993 Mercedes-Benz 190E, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1988-1993 Mercedes-Benz 300CE, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1990-1993 Mercedes-Benz 300D, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1987 Mercedes-Benz 300D, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1993 Mercedes-Benz 300E, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mercedes-Benz 300SD, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1988-1993 Mercedes-Benz 300SE, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1990-1993 Mercedes-Benz 300SL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1988-1993 Mercedes-Benz 300TE, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mercedes-Benz 400E, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1993 Mercedes-Benz 400SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mercedes-Benz 500E, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1993 Mercedes-Benz 500SEC, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mercedes-Benz 500SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1990-1993 Mercedes-Benz 500SL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1993 Mercedes-Benz 600SEC, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992-1993 Mercedes-Benz 600SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1993 Mercedes-Benz 600SL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1992 Mercedes-Benz 400SE, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1988-1991 Mercedes-Benz 300SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1991 Mercedes-Benz 350SD, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1990-1991 Mercedes-Benz 350SDL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Mercedes-Benz 420SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Mercedes-Benz 560SEC, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1991 Mercedes-Benz 560SEL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1987-1989 Mercedes-Benz 260E, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1989 Mercedes-Benz 560SL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1986-1987 Mercedes-Benz 300SDL, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1987 Mercedes-Benz 300TD, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1985 Mercedes-Benz 380SE, N\/A, 80mm.\u003c\/li\u003e\n\u003cli\u003eFits 1985 Mercedes-Benz 380SL, N\/A, 80mm.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Rein","offers":[{"title":"Default Title","offer_id":43756533973173,"sku":"DFBS-ABV0115P","price":14.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/C8_ABV0115P_Fro.jpg?v=1774994676"},{"product_id":"rein-abv0202-vacuum-line","title":"Rein ABV0202 Vacuum Line","description":"\u003ch2\u003eOE-Style Breather Hose for BMW Applications\u003c\/h2\u003e\u003cp\u003eRein ABV0202 is an OE-quality breather hose built for European vehicles that need a direct replacement with the original hose shape, branch layout, and quick-connect fitment style. It is made for BMW vacuum system and emission control service where correct routing and sealing matter.\u003c\/p\u003e\u003cp\u003eCompatible With BMW X5, 320i, 325Ci, 325i, 325xi, 330Ci, 330i, 330xi, 525i, 530i, Z3, 323Ci, 323i, 328Ci, 328i, and 528i applications across the listed model years. Rein ABV0202 is also a direct OE-style replacement for BMW breather hose service where the factory hose has cracked, hardened, or lost its seal.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMatches original equipment design specifications\u003c\/li\u003e\n\u003cli\u003eManufactured with high-quality plastic materials\u003c\/li\u003e\n\u003cli\u003eDirect fit for easier installation\u003c\/li\u003e\n\u003cli\u003eBuilt to strict engineering standards for materials and tolerances\u003c\/li\u003e\n\u003cli\u003eOE-style form, fit, and function for European vehicle service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Rein breather hose is engineered as a direct replacement for the original BMW hose used in emission control and vacuum system routing. The hose follows OE dimensions, including the branch shape and thermoplastic quick-connect style, so it installs in the factory path without altering the system layout. Rein ABV0202 is a practical choice for BMW X5, 3 Series, 5 Series, and Z3 models when the original hose no longer seals properly or shows age-related wear.\u003c\/p\u003e\u003cp\u003eThe hose uses plastic construction and application-specific sizing with 0.1200-inch inside diameter ends and 0.3300-inch outside diameter ends. Rein ABV0202 is designed for the same form, fit, and function as the original part, making it suitable for BMW breather hose replacement service where accurate routing is important. This part cross-references BMW OE numbers 11727574490 and 11737500269 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCracked or brittle breather hose sections\u003c\/li\u003e\n\u003cli\u003eVacuum leaks caused by worn hose connections\u003c\/li\u003e\n\u003cli\u003eImproper crankcase ventilation routing\u003c\/li\u003e\n\u003cli\u003eCheck engine light concerns related to air leak conditions\u003c\/li\u003e\n\u003cli\u003eRough idle or drivability issues tied to hose deterioration\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the hose routing against the original BMW layout before installation. Inspect adjoining connectors and nearby vacuum lines for wear, since a damaged mating fitting can affect sealing even when the hose is replaced. Confirm the part number ABV0202 against the vehicle’s engine and hose configuration before service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eRein manufactures this breather hose to OE-quality standards with attention to material selection and dimensional accuracy. ABV0202 includes a 24-month or 24,000-mile warranty.\u003c\/p\u003e","brand":"Rein","offers":[{"title":"Default Title","offer_id":43756538003637,"sku":"DFBS-ABV0202","price":33.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/C8_ABV0202_Fro.jpg?v=1774994692"},{"product_id":"genuine-0021408460-vacuum-check-valve","title":"Genuine 0021408460 Vacuum Check Valve","description":"\u003ch2\u003eMercedes-Benz Vacuum Check Valve\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum check valve, part number 0021408460, is used in the engine vacuum system to maintain one-way vacuum flow. It supports consistent vacuum control across a wide range of Mercedes-Benz applications, including C300, E350, ML350, and GL450 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine replacement vacuum check valve for the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eHelps maintain vacuum direction and system stability\u003c\/li\u003e\n\u003cli\u003eDirect fit for multiple Mercedes-Benz models from 2005-2015\u003c\/li\u003e\n\u003cli\u003eOE-style service part identified by part number 0021408460\u003c\/li\u003e\n\u003cli\u003eFits applications across C-Class, E-Class, ML-Class, GL-Class, SL-Class, and more\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003ePart number 0021408460 is a Genuine vacuum check valve designed for Mercedes-Benz engine vacuum system service. It is used on applications such as 2008-2014 Mercedes-Benz C300, 2006-2011 Mercedes-Benz E350, and 2007-2014 Mercedes-Benz GL450, along with additional fitments across the Mercedes-Benz lineup. This valve helps preserve proper vacuum routing in the engine vacuum system, which is critical for stable operation of vacuum-controlled components.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2008-2015 Mercedes-Benz GL550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2008-2014 Mercedes-Benz C300, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Mercedes-Benz G550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 Mercedes-Benz GL450, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2010-2014 Mercedes-Benz GLK350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2011-2014 Mercedes-Benz SL550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Mercedes-Benz SL550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2010-2013 Mercedes-Benz S400, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Mercedes-Benz C350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Mercedes-Benz CL550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Mercedes-Benz CLS550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Mercedes-Benz E350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Mercedes-Benz E550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Mercedes-Benz ML350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2010-2011 Mercedes-Benz ML450, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2008-2011 Mercedes-Benz ML550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Mercedes-Benz R350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Mercedes-Benz S550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Mercedes-Benz SLK300, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2005-2011 Mercedes-Benz SLK350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2009 Mercedes-Benz CLK350, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Mercedes-Benz CLK550, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Mercedes-Benz SLK280, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercedes-Benz C230, Engine Vacuum System\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercedes-Benz C280, Engine Vacuum System\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring proper vacuum retention in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eAddressing vacuum flow issues caused by a worn or failed check valve\u003c\/li\u003e\n\u003cli\u003eSupporting consistent operation of vacuum-operated engine components\u003c\/li\u003e\n\u003cli\u003eReplacing a leaking or sticking vacuum valve during maintenance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the part number 0021408460 against the existing valve before installation. Confirm the vehicle’s engine vacuum system routing and inspect connected hoses and fittings for wear, cracks, or contamination before reassembly. Use the listed fitment to match the exact Mercedes-Benz model and year.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eGenuine OE replacement part for Mercedes-Benz engine vacuum system service. Fitment is listed for confirmed applications across 2005-2015 Mercedes-Benz models.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43887693594805,"sku":"DFPH-0021408460","price":31.91,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_0021408460_Top_3225380e-3e95-4506-ac0e-bd19d52c4096.jpg?v=1775003182"},{"product_id":"genuine-1020940812-vacuum-hose-connector","title":"Genuine 1020940812 Vacuum Hose Connector","description":"\u003ch2\u003eVacuum Hose Connector for Mercedes-Benz\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum hose connector, part number 1020940812, is a direct-fit emission control component for select Mercedes-Benz models. It connects vacuum routing between the valve cover and idle air distributor or distributor air lines, helping maintain proper vacuum flow in the engine’s emission control system.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine vacuum hose connector for emission control vacuum routing\u003c\/li\u003e\n\u003cli\u003ePart number 1020940812 for accurate identification\u003c\/li\u003e\n\u003cli\u003eUsed at the valve cover, idle air distributor, and distributor air lines depending on application\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for select Mercedes-Benz 190E, 380SE, 380SL, 380SEC, 380SEL, and 380SLC models\u003c\/li\u003e\n\u003cli\u003eFits broad 1981-1993 Mercedes-Benz coverage with application-specific notes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003ePart number 1020940812 is a Genuine vacuum hose connector built for emission control vacuum system service on select Mercedes-Benz vehicles. It is used in vacuum line routing at the valve cover and idle air distributor on Mercedes-Benz 190E applications, and at distributor air lines on several 380-series models. For buyers searching for a Mercedes-Benz 190E vacuum hose connector or a Genuine 1020940812 replacement, this part matches the listed factory applications by year and engine configuration notes.\u003c\/p\u003e\u003cp\u003eCompatible With 1984 Mercedes-Benz 190E, from valve cover hose to idle air distributor; up to 038024 and up to 063869. Compatible With 1985 Mercedes-Benz 190E, between valve cover and idle air distributor; from 017190 and from 059588. Compatible With 1986-1988 Mercedes-Benz 190E, between valve cover and idle air distributor; from 017190 and from 059588. Compatible With 1991-1993 Mercedes-Benz 190E, between valve cover and idle air distributor; from 017190 and from 059588. It also fits 1984-1985 Mercedes-Benz 380SE, at distributor air lines; 1981-1985 Mercedes-Benz 380SL, at distributor air lines; 1982-1983 Mercedes-Benz 380SEC, at distributor air lines; 1981-1983 Mercedes-Benz 380SEL, at distributor air lines; and 1981 Mercedes-Benz 380SLC, at distributor air lines.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum leaks in the emission control hose routing\u003c\/li\u003e\n\u003cli\u003eCracked or deteriorated connector material at the valve cover or distributor air lines\u003c\/li\u003e\n\u003cli\u003eIdle quality issues related to vacuum line disruption\u003c\/li\u003e\n\u003cli\u003eIncorrect vacuum routing during Mercedes-Benz 190E or 380-series vacuum system repair\u003c\/li\u003e\n\u003cli\u003eRestoration of factory-style vacuum hose connections\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, model, and engine-specific notes before ordering, since this connector is application-dependent. Match the connector location to the listed routing point on your Mercedes-Benz 190E or 380-series model, and inspect adjacent vacuum hoses for age-related wear before installation. This part cross-references no additional part numbers in the provided data.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eGenuine parts are selected to match the listed factory application details for Mercedes-Benz emission control vacuum system service. Part number 1020940812 is identified for the exact fitment shown above.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43887850815669,"sku":"DFPH-1020940812","price":10.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_1020940812_Top.jpg?v=1775003272"},{"product_id":"genuine-1160940982-vacuum-hose","title":"Genuine 1160940982 Vacuum Hose","description":"\u003ch2\u003eGenuine Vacuum Hose for Mercedes-Benz Emissions Control\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum hose, part number 1160940982, is a direct-fit emission control component for select Mercedes-Benz models. It is used in distributor line applications tied to the injector system, making it a relevant replacement for vacuum routing on classic V8 Mercedes-Benz vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine OE replacement vacuum hose\u003c\/li\u003e\n\u003cli\u003ePart number 1160940982\u003c\/li\u003e\n\u003cli\u003eEmission control and vacuum system application\u003c\/li\u003e\n\u003cli\u003eDistributor line to injector use on select Mercedes-Benz models\u003c\/li\u003e\n\u003cli\u003eDirect fitment for 1981-1985 Mercedes-Benz applications listed below\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eGenuine 1160940982 is a vacuum hose for the emission control vacuum system, specified for distributor line to injector routing on select Mercedes-Benz 380SE, 380SL, 380SEC, 380SEL, 380SLC, 500SEC, and 500SEL models. This part number is listed for 1981-1985 Mercedes-Benz vehicles and is used where factory vacuum line routing must be maintained for proper engine control and emissions function. If your vehicle requires the noted plug reference, verify the application before installation. This part cross-references 116 997 12 86 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 380SE, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 380SE, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981-1985 Mercedes-Benz 380SL, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981-1985 Mercedes-Benz 380SL, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 500SEC, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 500SEC, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1984-1985 Mercedes-Benz 500SEL, 117.963; distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1982-1983 Mercedes-Benz 380SEC, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1982-1983 Mercedes-Benz 380SEC, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981-1983 Mercedes-Benz 380SEL, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981-1983 Mercedes-Benz 380SEL, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981 Mercedes-Benz 380SLC, distributor line to injector; may require plug - 4 x 116 997 12 86.\u003c\/li\u003e\n\u003cli\u003eFits 1981 Mercedes-Benz 380SLC, distributor line to injectors; may require plug 4 x 116 997 12 86.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCracked or deteriorated vacuum hose routing\u003c\/li\u003e\n\u003cli\u003eVacuum leaks in distributor line circuits\u003c\/li\u003e\n\u003cli\u003eIncorrect injector vacuum line connection\u003c\/li\u003e\n\u003cli\u003eEmissions system performance issues tied to hose failure\u003c\/li\u003e\n\u003cli\u003eRestoration needs on classic Mercedes-Benz vacuum plumbing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle year, model, and engine-specific notes before ordering, especially on 500SEL applications marked 117.963. Match the original hose routing and verify whether the plug reference 116 997 12 86 is required for your application. On Mercedes-Benz 380SE and Mercedes-Benz 380SL models, part number 1160940982 is listed for distributor line to injector or injectors configurations.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eAs a Genuine OE-style part, this vacuum hose follows factory application references for the listed Mercedes-Benz models and supports accurate replacement of the original emission control hose.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43889698046133,"sku":"DFPH-1160940982","price":25.65,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_1160940982_Top.jpg?v=1775003365"},{"product_id":"genuine-1160942582-vacuum-hose","title":"Genuine 1160942582 Vacuum Hose","description":"\u003ch2\u003eMercedes-Benz Vacuum Hose for Distributor Line\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum hose, part number 1160942582, is a direct-fit emission control component for select Mercedes-Benz models. It is used on distributor line applications and supports proper vacuum routing in the engine bay.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine replacement vacuum hose for emission control and vacuum system service\u003c\/li\u003e\n\u003cli\u003eFits Mercedes-Benz 420SEL, 560SEC, 560SEL, and 560SL applications listed below\u003c\/li\u003e\n\u003cli\u003eUsed for distributor line to injector and distributor line to injectors routing\u003c\/li\u003e\n\u003cli\u003eOE-style fitment for maintenance on classic Mercedes-Benz fuel and vacuum systems\u003c\/li\u003e\n\u003cli\u003ePart number 1160942582 for accurate ordering and identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eGenuine 1160942582 is a vacuum hose for Mercedes-Benz emission control and vacuum system applications. It is listed for 1986-1991 Mercedes-Benz 420SEL, 560SEC, and 560SEL, plus 1986-1989 Mercedes-Benz 560SL, with distributor line to injector and distributor line to injectors notes. If you are servicing a Mercedes-Benz 420SEL vacuum hose, Mercedes-Benz 560SEL distributor line hose, or Mercedes-Benz 560SL emission control hose, this part number helps match the correct application.\u003c\/p\u003e\u003cp\u003eThis part cross-references no additional part numbers in the provided data.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring vacuum routing between the distributor line and injectors\u003c\/li\u003e\n\u003cli\u003eReplacing cracked, hardened, or leaking vacuum hose sections\u003c\/li\u003e\n\u003cli\u003eAddressing rough idle caused by vacuum loss\u003c\/li\u003e\n\u003cli\u003eCorrecting drivability issues tied to vacuum system leaks\u003c\/li\u003e\n\u003cli\u003eMaintaining proper emission control system operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle year, model, and distributor-line routing before installation. Compare the original hose path and connection points to the existing setup on the engine. For best results, inspect nearby vacuum lines and injector-area connections at the same time so the repaired system remains sealed.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eGenuine parts are sourced as original-equipment replacement components for the listed Mercedes-Benz applications. Confirm fitment against the vehicle’s model year and vacuum routing before purchase.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43889698570421,"sku":"DFPH-1160942582","price":25.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_1160942582_Top_39916da1-f3ff-4c52-8d96-d6a8f39c4b7f.jpg?v=1775003366"},{"product_id":"genuine-1233040220-vacuum-valve-lever","title":"Genuine 1233040220 Vacuum Valve Lever","description":"\u003ch2\u003eMercedes-Benz Vacuum Valve Lever\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum valve lever is a direct-fit emission control component for select Mercedes-Benz diesel applications. It is used at the valve cover on OM617-series engines and supports the vacuum system layout found in Federal and California configurations.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eGenuine replacement part for emission control vacuum system service\u003c\/li\u003e\n\u003cli\u003eVacuum valve lever for valve cover mounting locations\u003c\/li\u003e\n\u003cli\u003eFits select Mercedes-Benz 300D, 300SD, and 300TD diesel models\u003c\/li\u003e\n\u003cli\u003eApplication-specific coverage for OM617.950, OM617.951, and OM617.952 engines\u003c\/li\u003e\n\u003cli\u003ePart number 1233040220 for accurate ordering and catalog matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1984 Mercedes-Benz 300D, N\/A — 617.952; at valve cover; Federal Cars\u003c\/li\u003e\n\u003cli\u003eFits 1984 Mercedes-Benz 300SD, N\/A — 617.951 at valve cover for Federal Cars\u003c\/li\u003e\n\u003cli\u003eFits 1982-1984 Mercedes-Benz 300TD, N\/A — 617.952; at valve cover\u003c\/li\u003e\n\u003cli\u003eFits 1982-1983 Mercedes-Benz 300D, N\/A — 617.952; at valve cover\u003c\/li\u003e\n\u003cli\u003eFits 1981-1983 Mercedes-Benz 300SD, N\/A — Vacuum Valve Lever fitment: 617.951\u003c\/li\u003e\n\u003cli\u003eFits 1981 Mercedes-Benz 300TD, N\/A — w\/ OM617.952\u003c\/li\u003e\n\u003cli\u003eFits 1978-1980 Mercedes-Benz 300SD, N\/A — 617.950 vacuum valve lever fits California Cars with 3 \/ 2 Way Valve starting from 014182\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Part Addresses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum control issues at the valve cover\u003c\/li\u003e\n\u003cli\u003eIncorrect or worn emission control lever operation\u003c\/li\u003e\n\u003cli\u003eVacuum routing problems on OM617 diesel engines\u003c\/li\u003e\n\u003cli\u003eFitment mismatches during Mercedes-Benz 300D, 300SD, or 300TD repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify engine code and emissions configuration before installation. This part number 1233040220 is listed for specific Federal and California Mercedes-Benz diesel applications, so match the vehicle year, model, and engine designation to the fitment notes before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eGenuine OE-style replacement part identification helps maintain correct catalog fitment for the specified Mercedes-Benz diesel applications. This part cross-references no additional part numbers in the provided data.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43889758830773,"sku":"DFPH-1233040220","price":18.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_1233040220_Top.jpg?v=1775003392"},{"product_id":"genuine-2712301165-vacuum-pump","title":"Genuine 2712301165 Vacuum Pump","description":"\u003ch2\u003eVacuum Pump for Mercedes-Benz C230\u003c\/h2\u003e\u003cp\u003eThis Genuine vacuum pump is a direct-fit emission control component for select Mercedes-Benz C230 models. It is listed for 2003-2005 Mercedes-Benz C230 applications and is identified by part number 2712301165.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eGenuine OE replacement vacuum pump\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Mercedes-Benz C230, N\/A\u003c\/li\u003e\n\u003cli\u003eSupports vacuum supply within the emission control system\u003c\/li\u003e\n\u003cli\u003ePart number 2712301165 for accurate ordering and lookup\u003c\/li\u003e\n\u003cli\u003eBuilt for direct replacement use on the listed vehicle application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eUse this vacuum pump when servicing the emission control vacuum system on a Mercedes-Benz C230. The pump is cataloged for 2003, 2004, and 2005 model years, making it a focused fitment for owners searching for a Mercedes-Benz C230 vacuum pump, 2712301165, or an OE replacement vacuum pump for 2003-2005 Mercedes-Benz C230 models. Genuine part number 2712301165 provides a straightforward match for the listed application.\u003c\/p\u003e\u003ch2\u003eCommon Issues It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply in the emission control system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability or system performance faults\u003c\/li\u003e\n\u003cli\u003eFailed inspection results tied to vacuum pump operation\u003c\/li\u003e\n\u003cli\u003eNoise or irregular operation from a worn vacuum pump\u003c\/li\u003e\n\u003cli\u003eReplacement needs after vacuum pump wear or failure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle is a 2003-2005 Mercedes-Benz C230 before ordering. Match the part number 2712301165 to the existing component and verify the mounting location and vacuum connections during removal. After installation, inspect the system for leaks and confirm proper vacuum operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eGenuine parts are sourced as original-equipment replacement components for the listed application, supporting accurate fitment and serviceability on the specified Mercedes-Benz C230 models.\u003c\/p\u003e","brand":"Genuine","offers":[{"title":"Default Title","offer_id":43898958610613,"sku":"DFPH-2712301165","price":326.61,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/GU_2712301165_AC1.jpg?v=1775003599"},{"product_id":"pierburg-7-00437-02-0-vacuum-pump","title":"Pierburg 7.00437.02.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for BMW Diesel Applications\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.00437.02.0 is a mechanical vacuum pump for diesel engine vacuum systems. It is built with an angled shape, one connector, and includes a seal ring for service replacement on select BMW diesel models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for diesel applications\u003c\/li\u003e\n\u003cli\u003eAngled housing design for application-specific fitment\u003c\/li\u003e\n\u003cli\u003eSingle connector configuration\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003cli\u003eCross-reference: Dorman - HELP 91050 for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eCompatible with 2009-2013 BMW X5 and 2009-2011 BMW 335d. This Pierburg vacuum pump, part number 7.00437.02.0, is used in emission control and engine vacuum systems on diesel vehicles where stable vacuum supply is required for proper component operation. The 7.00437.02.0 is also referenced by aftermarket numbers used for the same application, including OE-style interchange part numbers.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns on diesel applications\u003c\/li\u003e\n\u003cli\u003eEmission control system performance issues tied to vacuum loss\u003c\/li\u003e\n\u003cli\u003eLeaks at the pump mounting surface when the seal ring is worn\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify engine code and existing pump configuration before installation. Confirm the angled housing, one-connector layout, and seal ring requirement match the removed unit. Clean the mounting surface thoroughly and inspect connected vacuum lines for cracks, hardening, or contamination before placing the replacement pump in service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is a recognized OE supplier in engine management and emission control components. Part number 7.00437.02.0 is manufactured to meet the application-specific requirements listed for BMW diesel vacuum system service.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934487150773,"sku":"JCJT-7.00437.02.0","price":258.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_700437020_Fro.jpg?v=1775005044"},{"product_id":"pierburg-7-00906-22-0-vacuum-pump","title":"Pierburg 7.00906.22.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for Diesel Vacuum Systems\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.00906.22.0 is a mechanical vacuum pump for diesel applications that supports vacuum supply in the emission control and engine vacuum system. It is a direct-fit style service part for select Audi Q7 and Volkswagen Touareg models, with a straight housing design and one connector.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg vacuum pump for diesel engines\u003c\/li\u003e\n\u003cli\u003ePart number: 7.00906.22.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode for engine-driven vacuum generation\u003c\/li\u003e\n\u003cli\u003eStraight shape with 1 connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring for service replacement\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003ePierburg 7.00906.22.0 is a mechanical vacuum pump used in diesel emission control and vacuum system service. It is listed for 2009-2012 Audi Q7 and 2009-2012 Volkswagen Touareg applications, making it a relevant replacement when servicing vacuum-related engine functions on these platforms. The straight configuration and single-connector layout support OE-style fitment, while the included seal ring helps complete the pump replacement at the mounting interface. This part number, 7.00906.22.0, also cross-references 057145100AB for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring vacuum supply on diesel engine systems\u003c\/li\u003e\n\u003cli\u003eAddressing low vacuum output in Audi Q7 and Volkswagen Touareg service work\u003c\/li\u003e\n\u003cli\u003eReplacing a worn or leaking mechanical vacuum pump\u003c\/li\u003e\n\u003cli\u003eCorrecting vacuum-related drivability or control issues tied to engine vacuum demand\u003c\/li\u003e\n\u003cli\u003eSupporting emission control system operation where vacuum is required\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s engine and OE part number before installation. Confirm the mounting style, connector count, and seal condition during service, and follow the manufacturer technical reference SI 0109-11 for application-specific procedures. For fitment-based searches, this part fits 2009-2012 Audi Q7 and fits 2009-2012 Volkswagen Touareg.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE-focused brand in engine management and vacuum system components. Use the listed part number 7.00906.22.0 and vehicle fitment details to confirm application before installation.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934489804981,"sku":"JCJT-7.00906.22.0","price":260.37,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_700906220_Fro.jpg?v=1775005047"},{"product_id":"pierburg-7-01219-17-0-vacuum-pump","title":"Pierburg 7.01219.17.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for Porsche Applications\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.01219.17.0 is a mechanical vacuum pump for petrol engines in select Porsche models. It is built for emission control and vacuum system service, with a straight shape, one connector, and a seal ring for proper sealing at installation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for petrol engine applications\u003c\/li\u003e\n\u003cli\u003eStraight housing design with 1 connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring for sealing at the mounting point\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003cli\u003eDirect replacement reference: 7.01219.17.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is used in Porsche Cayenne, Macan, and Panamera applications where engine vacuum is required for emission control system operation. The mechanical operating mode supports vacuum generation from engine-driven movement, making it a direct-fit service part for the listed petrol vehicles. If you are searching for a Porsche Cayenne vacuum pump, Porsche Macan vacuum pump, or Porsche Panamera vacuum pump, part number 7.01219.17.0 is the relevant OE-style reference for the listed fitments.\u003c\/p\u003e\u003cp\u003eThis part cross-references Porsche 94811005003 and 94811005004 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the emission control system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns tied to engine-driven vacuum generation\u003c\/li\u003e\n\u003cli\u003eSealing issues at the pump mounting point when the original seal ring is worn\u003c\/li\u003e\n\u003cli\u003eService replacement needs for Porsche Cayenne, Macan, and Panamera vacuum system repairs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm the vehicle uses a petrol engine before ordering.\u003c\/li\u003e\n\u003cli\u003eVerify connector count and pump shape against the original unit.\u003c\/li\u003e\n\u003cli\u003eInspect the mounting surface and replace any damaged sealing surfaces before installation.\u003c\/li\u003e\n\u003cli\u003eUse the technical reference SI 0109-11 when comparing service details.\u003c\/li\u003e\n\u003cli\u003eFits 2008-2018 Porsche Cayenne\u003c\/li\u003e\n\u003cli\u003eFits 2015-2018 Porsche Macan\u003c\/li\u003e\n\u003cli\u003eFits 2010-2016 Porsche Panamera\u003c\/li\u003e\n\u003cli\u003eFits 2019 Porsche Cayenne, Connector Pins: 1\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is a recognized supplier in emission control and vacuum system components, and this vacuum pump is built to match the listed OE applications for Porsche service work.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934490984629,"sku":"JCJT-7.01219.17.0","price":170.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_701219170_Fro.jpg?v=1775005049"},{"product_id":"pierburg-7-01341-03-0-vacuum-pump","title":"Pierburg 7.01341.03.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Mechanical Vacuum Pump for Volkswagen and Audi\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.01341.03.0 is a mechanical vacuum pump for petrol engines in select Volkswagen and Audi applications. It is built for vehicles that rely on engine vacuum for brake assist and other emission control functions, with fitment tied to specific OE numbers.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.01341.03.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode\u003c\/li\u003e\n\u003cli\u003ePetrol engine application\u003c\/li\u003e\n\u003cli\u003eStraight shape with 1 connector\u003c\/li\u003e\n\u003cli\u003eSupplied without gasket\/seal\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is an OE-style emission control component used on select Volkswagen CC, Tiguan, Eos, Jetta, Passat, GTI, GLI, Golf, Passat CC, and Audi A3, TT, TTS, and A3 Quattro applications. The 7.01341.03.0 is specified for vehicles with matching OE references, including 06H145100AB, 06H145100AD, 06H145100AK, 06H145100F, 06H145100L, 06H145100N, and 06H145100S. This part cross-references OE-style numbers such as 06H145100AD and 06H145100AK for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2018 Volkswagen Tiguan Limited, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Volkswagen Tiguan, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2017 Volkswagen Tiguan Limited, N\/A, with OE No. 06H145100AB, 06H145100AD, 06H145100AK, 06H145100F, 06H145100L\u003c\/li\u003e\n\u003cli\u003eFits 2015 Volkswagen CC, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2012 Volkswagen CC, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2015 Volkswagen Eos, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2012 Volkswagen Eos, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2012-2015 Volkswagen Tiguan, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2013-2014 Volkswagen CC, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Volkswagen CC, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2014 Volkswagen Eos, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Volkswagen Eos, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Audi A3, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2009-2013 Audi A3 Quattro, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013 Volkswagen Golf, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2013 Volkswagen GTI, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2011 Volkswagen GTI, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Volkswagen Jetta, N\/A, with OE No. 06H145100AK\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Volkswagen Jetta, N\/A, with OE No. 06H145100AK\u003c\/li\u003e\n\u003cli\u003eFits 2012 Volkswagen GTI, N\/A, with OE No. 06H145100AD\u003c\/li\u003e\n\u003cli\u003eFits 2011-2012 Volkswagen Passat CC, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Audi A3, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Volkswagen Tiguan, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Audi TT Quattro, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Audi TTS Quattro, N\/A, with OE No. 06H145100AB\u003c\/li\u003e\n\u003cli\u003eFits 2010 Volkswagen GLI, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2008-2010 Volkswagen Passat, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Volkswagen Passat CC, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2009 Audi TT, N\/A, with OE No. 06H145100AB\u003c\/li\u003e\n\u003cli\u003eFits 2008 Audi A3, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2008 Volkswagen Jetta, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Replacement Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores vacuum supply for brake assist systems\u003c\/li\u003e\n\u003cli\u003eAddresses vacuum loss caused by a worn or failing pump\u003c\/li\u003e\n\u003cli\u003eSupports proper operation of emission control vacuum circuits\u003c\/li\u003e\n\u003cli\u003eHelps correct vacuum-related drivability or braking concerns\u003c\/li\u003e\n\u003cli\u003eReplaces a pump matched to the listed OE numbers\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the OE number on the original unit before ordering, since fitment is tied to specific factory references. This pump is listed without a gasket or seal, so reuse or replacement of sealing components should be verified during service. Match the connector count, mechanical design, and straight configuration to the original part before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg supplies vacuum system components for emission control and engine vacuum applications. Part number 7.01341.03.0 is cataloged with Technical Information Number SI 0109-11 for application reference and identification.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934491148469,"sku":"JCJT-7.01341.03.0","price":332.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_701341030_Fro.jpg?v=1775005050"},{"product_id":"pierburg-7-01366-06-0-vacuum-pump","title":"Pierburg 7.01366.06.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump 7.01366.06.0\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.01366.06.0 is a mechanical vacuum pump for petrol engines in the emission control vacuum system. It is listed for 2007-2012 Mini Cooper applications and includes a seal ring for service replacement. This vacuum pump supports stable vacuum supply for engine-operated systems on the Mini Cooper platform.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.01366.06.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode\u003c\/li\u003e\n\u003cli\u003ePetrol fuel type application\u003c\/li\u003e\n\u003cli\u003eStraight shape with 1 connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring\u003c\/li\u003e\n\u003cli\u003eTechnical information number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBuilt for emission control vacuum system service, this Pierburg vacuum pump is specified for 2007-2012 Mini Cooper models. The mechanical design is suited to engine-driven vacuum generation, and the straight housing layout with a single connector supports direct replacement of the original unit. If you are sourcing a Pierburg 7.01366.06.0 vacuum pump for a Mini Cooper, this part provides the core specifications needed for OE-style service work.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - HELP 91141 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the emission control system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns tied to pump wear\u003c\/li\u003e\n\u003cli\u003eService replacement for a leaking pump assembly\u003c\/li\u003e\n\u003cli\u003eVacuum system faults on 2007-2012 Mini Cooper models\u003c\/li\u003e\n\u003cli\u003eSeal-related leakage at the pump mounting point\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2007-2012 Mini Cooper, N\/A. Confirm the connector style, mounting layout, and engine-side vacuum routing before installation. Replace the seal ring during service and verify that the vacuum lines are seated correctly after installation. Use the technical information reference SI 0109-11 when matching the part to the vehicle.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and emission control components, and this vacuum pump is built to match the listed application details for accurate replacement service.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934491639989,"sku":"JCJT-7.01366.06.0","price":200.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_701366060_Fro.jpg?v=1775005050"},{"product_id":"pierburg-7-01490-09-0-vacuum-pump","title":"Pierburg 7.01490.09.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for Mini Cooper\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump, part number 7.01490.09.0, is a mechanical emission control component for petrol engines. It is built for direct replacement use on select Mini Cooper models from 2007-2010 and includes a seal ring for proper sealing at installation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.01490.09.0\u003c\/li\u003e\n\u003cli\u003eCategory: Emission Control \u0026gt; Vacuum System\u003c\/li\u003e\n\u003cli\u003eFuel type: Petrol\u003c\/li\u003e\n\u003cli\u003eOperating mode: Mechanical\u003c\/li\u003e\n\u003cli\u003eShape: Straight\u003c\/li\u003e\n\u003cli\u003e1 connector for the specified application\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDesigned for the vacuum system in petrol-powered vehicles, this Pierburg vacuum pump supports the engine’s vacuum-dependent functions with a mechanical operating design and a straight housing layout. The single-connector configuration and included seal ring make it a focused replacement part for the specified application. This part number, 7.01490.09.0, is listed for 2007-2010 Mini Cooper models and is also referenced in cross-application catalogs under Dorman - HELP 91129 and Nissens 91178.\u003c\/p\u003e\u003cp\u003eCompatible With 2007-2010 Mini Cooper, N\/A. Use this Pierburg vacuum pump when servicing a Mini Cooper vacuum system and replacing a worn or leaking pump assembly. The part number 7.01490.09.0 appears in interchange listings that help confirm application matching for the same vehicle platform.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eReplacing a vacuum pump with reduced vacuum output\u003c\/li\u003e\n\u003cli\u003eAddressing vacuum leaks in the emission control system\u003c\/li\u003e\n\u003cli\u003eRestoring vacuum supply for engine-operated components\u003c\/li\u003e\n\u003cli\u003eCorrecting noise or irregular operation from a worn mechanical pump\u003c\/li\u003e\n\u003cli\u003eServicing a petrol Mini Cooper vacuum system\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the connector count, operating mode, and shape against the removed part before installation. Confirm the seal ring is seated correctly during assembly, and match the application to 2007-2010 Mini Cooper, N\/A. Refer to technical information SI 0109-11 for additional service details tied to part number 7.01490.09.0.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE-focused brand in engine management and emission control components. This vacuum pump is built to meet the specified application requirements for the listed Mini Cooper fitment.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934491672757,"sku":"JCJT-7.01490.09.0","price":198.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_701490090_Fro.jpg?v=1775005050"},{"product_id":"pierburg-7-02318-01-0-diverter-valve","title":"Pierburg 7.02318.01.0 Diverter Valve","description":"\u003ch2\u003ePierburg 7.02318.01.0 Diverter Valve\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.02318.01.0 is an electric diverter valve with a 12-volt switch valve design for emission control vacuum system applications. It is used on a wide range of BMW and Mini vehicles, including turbocharged BMW 328i, 535i, 550i, X5, and Mini Cooper models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eElectric operating mode for controlled vacuum system response\u003c\/li\u003e\n\u003cli\u003eSwitch valve design for emission control applications\u003c\/li\u003e\n\u003cli\u003e12 V electrical specification\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0100\u003c\/li\u003e\n\u003cli\u003eDirect replacement part number: Pierburg 7.02318.01.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg diverter valve is built for emission control and vacuum system service on many BMW and Mini platforms. It is listed across a broad range of applications, including BMW 128i, 135i, 328i, 528i, 535i, 550i, 740i, X3, X5, X6, Z4, and Mini Cooper models, as well as select Land Rover Discovery and Range Rover applications. This part number, 7.02318.01.0, also cross-references URO 11747810831 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum control faults in the emission system\u003c\/li\u003e\n\u003cli\u003eImproper diverter valve operation under boost-related conditions\u003c\/li\u003e\n\u003cli\u003eCheck engine light concerns tied to vacuum or valve performance\u003c\/li\u003e\n\u003cli\u003eDriveability issues caused by inconsistent vacuum switching\u003c\/li\u003e\n\u003cli\u003eReplacement needs for worn or electrically failed switch valves\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s original part number and connector style before installation. Confirm fitment by year, make, and model, especially on BMW 328i, 535i, and X5 applications where multiple engine and chassis combinations exist. Follow factory service procedures for vacuum line routing and electrical connection checks during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is a recognized OE supplier in engine management and emission control components. This diverter valve is manufactured to meet the specified electrical and functional requirements for the listed applications.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934495539381,"sku":"JCJT-7.02318.01.0","price":56.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_702318010_Fro_693fed1d-96cf-48ba-beea-9d588842e004.jpg?v=1775005058"},{"product_id":"pierburg-7-21071-50-0-diverter-valve","title":"Pierburg 7.21071.50.0 Diverter Valve","description":"\u003ch2\u003ePierburg Diverter Valve for Mercedes-Benz Vacuum Systems\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.21071.50.0 is an electric-pneumatic diverter valve used in Mercedes-Benz emission control and vacuum system applications. It is a 12-volt switch valve built to manage vacuum signal routing in vehicles that rely on precise pneumatic control.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eElectric-pneumatic operating mode for vacuum system control\u003c\/li\u003e\n\u003cli\u003e12V electrical specification\u003c\/li\u003e\n\u003cli\u003eSwitch valve design for controlled vacuum diversion\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0100\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for select Mercedes-Benz applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eThis Pierburg diverter valve, part number 7.21071.50.0, is used in Mercedes-Benz vacuum and emission control systems where accurate switching of vacuum flow is required. It fits a wide range of Mercedes-Benz models, including 2009-2015 Mercedes-Benz G550, 2002-2008 Mercedes-Benz G500, 2003-2004 Mercedes-Benz G55 AMG, 1999-2003 Mercedes-Benz E320, 1994-1997 Mercedes-Benz E320, 2000-2001 Mercedes-Benz SL500, 1994-1998 Mercedes-Benz SL500, 1997-2000 Mercedes-Benz C230, 1994-2000 Mercedes-Benz C280, and 1998-2000 Mercedes-Benz C43 AMG. Additional fitments include Mercedes-Benz CL500, CL600, CLK320, CLK430, E300, E430, E55 AMG, ML320, ML430, S320, S420, S500, S600, SL600, C220, C36 AMG, E420, S350, 190E, 300CE, 300E, 300SE, 300TE, 500SL, 300SEL, 560SEL, 260E, 560SL, and 300D in the listed model years.\u003c\/p\u003e\u003cp\u003eThis part cross-references OSC 98072 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Symptoms It May Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum switching faults in the emission control system\u003c\/li\u003e\n\u003cli\u003eIrregular actuator response caused by failed vacuum routing\u003c\/li\u003e\n\u003cli\u003eCheck engine concerns related to vacuum control performance\u003c\/li\u003e\n\u003cli\u003eLoss of proper pneumatic signal control in Mercedes-Benz systems\u003c\/li\u003e\n\u003cli\u003eDriveability issues tied to malfunctioning diverter valve operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the OE number and vehicle application before installation, especially on Mercedes-Benz models that require A0015400097 or related interchange references. Verify the electrical connection, vacuum hose routing, and system voltage match the original setup. For best results, compare the removed valve to the new Pierburg 7.21071.50.0 before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in automotive control systems, and this diverter valve is built to meet the specifications needed for Mercedes-Benz vacuum system service. Use the listed technical information and fitment data to confirm correct application before replacement.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934511497397,"sku":"JCJT-7.21071.50.0","price":71.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_721071500_Fro.jpg?v=1775005082"},{"product_id":"pierburg-7-24807-20-0-vacuum-pump","title":"Pierburg 7.24807.20.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump 7.24807.20.0\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is a mechanical emission control component for petrol engines. It is built for direct-fit service on select Audi and Volkswagen applications, including Audi A4, Audi TT, TTS Quattro, A3, and Volkswagen Golf R, GTI, Jetta, Passat, and Eos models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for petrol engine applications\u003c\/li\u003e\n\u003cli\u003eSingle connector design with 1 connector pin configuration on listed applications\u003c\/li\u003e\n\u003cli\u003eStraight shape for OE-style mounting layout\u003c\/li\u003e\n\u003cli\u003eEmission control and vacuum system service part\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.20.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003ePierburg 7.24807.20.0 is a mechanical vacuum pump used in the emission control vacuum system to maintain the vacuum supply required by engine-related systems. It is specified for petrol-powered vehicles and matches a range of OE references, making it a practical replacement for service work on Audi and Volkswagen platforms. This part cross-references Dorman - HELP 91042 for the same application. It also aligns with OE numbers commonly associated with Audi A4, Audi TT, TTS Quattro, and Volkswagen Golf R service needs.\u003c\/p\u003e\u003cp\u003eFits 2015 Audi TTS Quattro, N\/A; Fits 2011-2014 Audi TTS Quattro, N\/A; Fits 2012-2013 Audi TT Quattro, N\/A; Fits 2012-2013 Volkswagen Golf R, N\/A; Fits 2009-2010 Audi TTS Quattro, N\/A, with OE No. 06D145100F; Fits 2005-2009 Audi A4, N\/A; Fits 2005-2009 Audi A4 Quattro, N\/A; Fits 2008-2009 Audi TT, N\/A, with OE No. 06D145100F; Fits 2007-2009 Volkswagen Eos, N\/A; Fits 2006-2008 Audi A3, N\/A; Fits 2006-2008 Volkswagen GTI, N\/A; Fits 2006-2008 Volkswagen Jetta, N\/A; Fits 2006-2008 Volkswagen Passat, N\/A; Fits 2007 Audi TT, N\/A, Connector Pins: 1.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns on petrol engines\u003c\/li\u003e\n\u003cli\u003eOE replacement needs for worn or failing vacuum pump assemblies\u003c\/li\u003e\n\u003cli\u003eService replacement for listed Audi and Volkswagen fitments\u003c\/li\u003e\n\u003cli\u003eRestoration of proper vacuum operation in emission control systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm OE number, connector count, and engine application before installation. This pump uses a mechanical operating mode and a straight housing layout, so matching the original mounting style is important. Verify the vehicle’s existing part number against 06D145100D, 06D145100E, 06D145100F, 06D145100G, or 06D145100H where applicable, and check the connector pin configuration on the vehicle before replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is a recognized OE supplier in engine management and emission control components. This vacuum pump is built to match the specified technical requirements for the listed applications, including the SI 0109-11 reference.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934522540213,"sku":"JCJT-7.24807.20.0","price":250.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807200_Fro.jpg?v=1775005100"},{"product_id":"pierburg-7-24807-21-0-vacuum-pump","title":"Pierburg 7.24807.21.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump 7.24807.21.0\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.21.0 is a mechanical vacuum pump for petrol engines in the emission control vacuum system. It is built with one connector and a straight shape, and it is supplied without a seal ring. This vacuum pump is a direct-fit service part for select Audi A4, Audi A4 Quattro, Audi A6, and Audi A6 Quattro applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.21.0\u003c\/li\u003e\n\u003cli\u003eFuel type: Petrol\u003c\/li\u003e\n\u003cli\u003eOperating mode: Mechanical\u003c\/li\u003e\n\u003cli\u003eOne connector for straightforward OE-style routing\u003c\/li\u003e\n\u003cli\u003eStraight housing design\u003c\/li\u003e\n\u003cli\u003eSupplied without seal ring\u003c\/li\u003e\n\u003cli\u003eTechnical information number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is used in the emission control vacuum system to support vacuum supply on petrol-powered engines. It cross-references Dorman - HELP 91043 for the same application. The 7.24807.21.0 also matches OE-style part numbers used on select Audi platforms, including 06E145100B, 06E145100C, 06E145100D, 06E145100E, and 06E145100T. For buyers searching by vehicle, this part is a fit for Audi A4 and Audi A4 Quattro models from 2005-2009, as well as Audi A6 and Audi A6 Quattro models from 2005-2010, with notes applying to certain A6 applications using OE No. 06E145100E.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2005-2009 Audi A4 Quattro, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Audi A4, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2008 Audi A6 Quattro, N\/A with OE No. 06E145100E\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Audi A6, N\/A with OE No. 06E145100E\u003c\/li\u003e\n\u003cli\u003eFits 2009 Audi A6 Quattro, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Audi A6, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Replacement Reasons\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum loss in the emission control vacuum system\u003c\/li\u003e\n\u003cli\u003eHard starting or inconsistent engine vacuum supply\u003c\/li\u003e\n\u003cli\u003eEngine performance issues tied to vacuum pump wear\u003c\/li\u003e\n\u003cli\u003eOil seepage or leakage at the pump mounting area\u003c\/li\u003e\n\u003cli\u003eFaults related to a worn mechanical vacuum pump on petrol engines\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm OE number match before installation, especially on Audi A6 applications with OE No. 06E145100E. Inspect the mounting surface and replace the seal ring if required, since this pump is supplied without a seal ring. Verify connector orientation, routing, and engine application against the vehicle’s original part number before final assembly.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and emission-related components. The 7.24807.21.0 is built to meet the specifications identified by technical information number SI 0109-11 for the listed Audi applications.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934522900661,"sku":"JCJT-7.24807.21.0","price":221.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807210_Fro.jpg?v=1775005101"},{"product_id":"pierburg-7-24807-23-0-vacuum-pump","title":"Pierburg 7.24807.23.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for BMW Emission Control\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.23.0 is a mechanical vacuum pump for petrol applications in BMW emission control and vacuum system service. It is built with a straight shape, one connector, and includes a seal ring for direct replacement work on supported vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.23.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode for petrol engines\u003c\/li\u003e\n\u003cli\u003eStraight housing design with 1 connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring\u003c\/li\u003e\n\u003cli\u003eTechnical information number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is specified for BMW vacuum system repair where stable mechanical vacuum supply is required for emission control operation. It cross-references Dorman - HELP 91029 for the same application. The 7.24807.23.0 is listed for BMW 550i, 650i, X5, 750i, 750Li, 760Li, 760i, 545i, 645Ci, 745i, and 745Li applications across model years 2002 through 2010.\u003c\/p\u003e\u003cp\u003eCompatible With BMW 550i, BMW 650i, BMW X5, BMW 750i, BMW 750Li, BMW 760Li, BMW 760i, BMW 545i, BMW 645Ci, BMW 745i, and BMW 745Li applications, this vacuum pump is a direct-fit service part for petrol-powered vehicles using a mechanical pump design. The Pierburg 7.24807.23.0 is a practical choice when replacing a worn or leaking vacuum pump in BMW emission control systems.\u003c\/p\u003e\u003ch2\u003eCommon Repair Symptoms\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply in the engine bay\u003c\/li\u003e\n\u003cli\u003eVacuum-related emission control faults\u003c\/li\u003e\n\u003cli\u003eOil seepage or leakage at the pump sealing surface\u003c\/li\u003e\n\u003cli\u003eHard brake or control-system vacuum performance issues tied to pump wear\u003c\/li\u003e\n\u003cli\u003eNoise or inconsistent operation from a failing mechanical pump\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify engine type, connector style, and mounting location before installation. This part is for petrol applications and uses a straight configuration with one connector. Replace the seal ring during service and confirm the vacuum lines and mating surfaces are clean before final assembly. Fitment includes 2002-2005 BMW 745i and 745Li, 2003-2008 BMW 760Li, 2004-2005 BMW 545i and 645Ci, 2004-2006 BMW 760i, 2004-2010 BMW X5, 2006-2008 BMW 750i and 750Li, and 2006-2010 BMW 550i and 650i.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and vacuum system components. Part number 7.24807.23.0 is identified with technical information reference SI 0109-11 for application verification.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934523195573,"sku":"JCJT-7.24807.23.0","price":195.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807230_Fro.jpg?v=1775005101"},{"product_id":"pierburg-7-24807-28-0-vacuum-pump","title":"Pierburg 7.24807.28.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Mechanical Vacuum Pump for Petrol Engines\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.28.0 is a mechanical vacuum pump for petrol applications that supports vacuum-dependent engine systems. Built with a straight shape and one connector, it is specified without a gasket or seal and references Technical Information Number SI 0109-11.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.28.0\u003c\/li\u003e\n\u003cli\u003eCategory: Emission Control \u0026gt; Vacuum System\u003c\/li\u003e\n\u003cli\u003eFuel type: Petrol\u003c\/li\u003e\n\u003cli\u003eOperating mode: Mechanical\u003c\/li\u003e\n\u003cli\u003eShape: Straight\u003c\/li\u003e\n\u003cli\u003eNumber of connectors: 1\u003c\/li\u003e\n\u003cli\u003eSupplied without gasket \/ seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eCompatible with select Audi and Volkswagen models using the listed OE numbers. Fits 2015-2018 Audi Q3, N\/A; Fits 2015-2018 Audi Q3 Quattro, N\/A; Fits 2018 Volkswagen Tiguan Limited, N\/A with OE No. 06J145100N; Fits 2016-2017 Volkswagen CC, N\/A; Fits 2013-2014 Volkswagen CC, N\/A; Fits 2015-2017 Volkswagen Tiguan, N\/A with OE No. 06J145100N; Fits 2017 Volkswagen Tiguan Limited, N\/A with OE No. 06J145100B, 06J145100F, 06J145100N; Fits 2016 Volkswagen Eos, N\/A; Fits 2013-2014 Volkswagen Eos, N\/A; Fits 2015 Volkswagen CC, N\/A with OE No. 06J145100N; Fits 2012 Volkswagen CC, N\/A with OE No. 06J145100N; Fits 2015 Volkswagen Eos, N\/A with OE No. 06J145100N; Fits 2012 Volkswagen Eos, N\/A with OE No. 06J145100N; Fits 2014 Volkswagen Tiguan, N\/A from 09\/01\/2014; Fits 2012-2013 Audi A3, N\/A with OE No. 06J145100F; Fits 2013 Volkswagen Beetle, N\/A with OE No. 06J145100N; Fits 2013 Volkswagen Golf, N\/A with OE No. 06J145100N; Fits 2013 Volkswagen GTI, N\/A; Fits 2012 Volkswagen Beetle, N\/A; Fits 2012 Volkswagen GTI, N\/A with OE No. 06J145100N; Fits 2008 Audi A3, N\/A.\u003c\/p\u003e\u003cp\u003eThis part cross-references OE numbers 06J145100B and 06J145100F for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring vacuum supply for engine-driven systems\u003c\/li\u003e\n\u003cli\u003eReplacing a worn or failing mechanical vacuum pump\u003c\/li\u003e\n\u003cli\u003eAddressing low vacuum output in petrol engine applications\u003c\/li\u003e\n\u003cli\u003eCorrecting vacuum-related drivability or braking-assist concerns tied to pump performance\u003c\/li\u003e\n\u003cli\u003eMatching OE-number-specific service needs on Audi and Volkswagen platforms\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Quality\u003c\/h2\u003e\u003cp\u003eVerify the OE number on the original unit before ordering, especially on Volkswagen Tiguan, Volkswagen CC, Audi A3, and Audi Q3 applications. Because this pump is listed without a gasket or seal, confirm the required sealing components during service and follow the vehicle-specific procedure for vacuum system replacement. Pierburg is an established OE supplier in engine management and vacuum system components, and this part is identified with Technical Information Number SI 0109-11.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934523228341,"sku":"JCJT-7.24807.28.0","price":314.91,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807280_Fro_ea0df132-e208-44b4-982c-7a9cbfba541f.jpg?v=1775005101"},{"product_id":"pierburg-7-24807-29-0-vacuum-pump","title":"Pierburg 7.24807.29.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for Audi 2.0T Petrol Applications\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.29.0 is a mechanical vacuum pump for petrol engines in select Audi applications. It is built for direct replacement use where OE reference 06J145100P is specified, including several Audi A4, A5, Q5, Q3, A6, allroad, and TT Quattro models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.29.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode\u003c\/li\u003e\n\u003cli\u003eDesigned for petrol fuel systems\u003c\/li\u003e\n\u003cli\u003eStraight shape with 1 connector\u003c\/li\u003e\n\u003cli\u003eSupplied without gasket or seal\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is an emission control and vacuum system component used to generate vacuum for engine-related control functions. The mechanical design supports OE-style replacement on Audi vehicles that call for part number 7.24807.29.0 or OE reference 06J145100P. It is listed for applications such as the 2014-2016 Audi A4 and A4 allroad, 2010-2015 Audi A5 and A5 Quattro, 2011-2015 Audi Q5, and 2011-2015 Audi TT Quattro, along with additional Audi fitments across the 2009-2017 model years.\u003c\/p\u003e\u003cp\u003eThis part cross-references URO 06J145100P for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eBrake assist concerns related to vacuum generation\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability faults on petrol Audi engines\u003c\/li\u003e\n\u003cli\u003eOE replacement needs when the original pump is worn or leaking\u003c\/li\u003e\n\u003cli\u003eFitment matching for vehicles using OE No. 06J145100P\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the OE number on the original unit before installation, especially on 2016-2017 Audi A4 Quattro, A5 Quattro, and Q5 applications with multiple OE references. This pump is listed without gasket or seal, so confirm the required sealing components separately. Check connector count, mounting style, and the straight housing configuration against the removed part before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and vacuum system components. The part number 7.24807.29.0 is cataloged with technical reference SI 0109-11 for application verification and service matching.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2017 Audi A5 Quattro, N\/A, with OE No. 06J145100P\u003c\/li\u003e\n\u003cli\u003eFits 2017 Audi Q5, N\/A, with OE No. 06J145100P\u003c\/li\u003e\n\u003cli\u003eFits 2014-2016 Audi A4, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2014-2016 Audi A4 allroad, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2016 Audi A4 Quattro, N\/A, With OE No. 06J145100C, 06J145100G, 06J145100P\u003c\/li\u003e\n\u003cli\u003eFits 2016 Audi A5 Quattro, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2016 Audi allroad, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2014-2016 Audi Q3 Quattro, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2016 Audi Q5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 Audi A4 Quattro, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2010-2015 Audi A5, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2010-2015 Audi A5 Quattro, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2015 Audi A6, N\/A, Without hybrid drive\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 Audi A6 Quattro, N\/A, Without hybrid drive\u003c\/li\u003e\n\u003cli\u003eFits 2011-2015 Audi Q5, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2011-2015 Audi TT Quattro, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2014 Audi A6, N\/A, To 12\/31\/2014\u003c\/li\u003e\n\u003cli\u003eFits 2009-2013 Audi A4, N\/A, From VIN # 8K8000001\u003c\/li\u003e\n\u003cli\u003eFits 2013 Audi A4 allroad, N\/A, From VIN # 8K8000001\u003c\/li\u003e\n\u003cli\u003eFits 2009-2013 Audi A4 Quattro, N\/A, From VIN # 8K8000001\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Audi A6, N\/A, Straight\u003c\/li\u003e\n\u003cli\u003eFits 2013 Audi A6 Quattro, N\/A, Straight\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934523293877,"sku":"JCJT-7.24807.29.0","price":249.43,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807290_Fro.jpg?v=1775005102"},{"product_id":"pierburg-7-24807-30-0-vacuum-pump","title":"Pierburg 7.24807.30.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Mechanical Vacuum Pump for Audi and Volkswagen\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.30.0 is a mechanical vacuum pump for petrol applications that rely on stable vacuum supply for brake assist and related engine systems. It features one connector, a straight shape, and OE-style fitment for select Audi RS3, Audi TT RS Quattro, Volkswagen Beetle, Golf, Jetta, Passat, and Golf SportWagen applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.30.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode for petrol engines\u003c\/li\u003e\n\u003cli\u003eOne connector for simplified OE-style connection\u003c\/li\u003e\n\u003cli\u003eStraight housing shape\u003c\/li\u003e\n\u003cli\u003eSupplied without gasket or seal\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is built for petrol-powered vehicles that require a mechanical vacuum source as part of the emission control and vacuum system. It is listed for select Audi RS3 and Audi TT RS Quattro models, along with Volkswagen Beetle, Golf, Golf SportWagen, Jetta, and Passat applications. The 7.24807.30.0 is also referenced against OE numbers used on these platforms, making it a practical replacement choice when matching the original pump configuration.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - HELP 91139 for the same application. The Pierburg 7.24807.30.0 is a direct-fit style replacement for vehicles that use the specified OE numbers and connector configuration.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring vacuum supply in petrol engine systems\u003c\/li\u003e\n\u003cli\u003eAddressing low or inconsistent vacuum output\u003c\/li\u003e\n\u003cli\u003eReplacing a worn or failing mechanical vacuum pump\u003c\/li\u003e\n\u003cli\u003eSupporting brake assist performance when vacuum delivery is affected\u003c\/li\u003e\n\u003cli\u003eCorrecting vacuum-related drivability or emission control faults\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify OE number match before ordering: 07K145100B, 07K145215A, 07K145100H, 07K145100L, and related references are listed for this application.\u003c\/li\u003e\n\u003cli\u003eConfirm connector count and pump shape against the original unit.\u003c\/li\u003e\n\u003cli\u003eThis pump is supplied without gasket or seal, so reuse or replacement of sealing components must be handled separately.\u003c\/li\u003e\n\u003cli\u003eUse the vehicle’s service information and Technical Information Number SI 0109-11 during installation.\u003c\/li\u003e\n\u003cli\u003eFits 2019-2020 Audi RS3, N\/A; Fits 2022-2024 Audi RS3, N\/A; Fits 2017-2018 Audi RS3, N\/A; Fits 2019-2020 Audi TT RS Quattro, N\/A; Fits 2022 Audi TT RS Quattro, N\/A; Fits 2021 Audi TT RS Quattro, N\/A; Fits 2018 Audi TT RS Quattro, N\/A; Fits 2014 Audi TT RS Quattro, N\/A; Fits 2013 Audi TT RS Quattro, N\/A; Fits 2012 Audi TT RS Quattro, N\/A; Fits 2011 Audi TT RS Quattro, N\/A; Fits 2014 Volkswagen Beetle, N\/A; Fits 2013-2014 Volkswagen Beetle, N\/A; Fits 2012 Volkswagen Beetle, N\/A; Fits 2011 Volkswagen Beetle, N\/A; Fits 2006-2010 Volkswagen Beetle, N\/A; Fits 2010-2011 Volkswagen Beetle Cabrio, N\/A; Fits 2014 Volkswagen Golf, N\/A; Fits 2010-2013 Volkswagen Golf, N\/A; Fits 2010-2013 Volkswagen Golf SportWagen, N\/A; Fits 2010-2014 Volkswagen Jetta, N\/A; Fits 2009-2010 Volkswagen Jetta, N\/A; Fits 2012-2014 Volkswagen Passat, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in vacuum and emission control components, and this pump follows the listed OE references and application data for fitment verification. Confirm the part number, connector count, and vehicle OE number before installation to ensure the correct match.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934523457717,"sku":"JCJT-7.24807.30.0","price":276.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807300_Fro.jpg?v=1775005102"},{"product_id":"pierburg-7-24807-31-0-vacuum-pump","title":"Pierburg 7.24807.31.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for BMW Petrol Engines\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.31.0 is a mechanical vacuum pump for petrol applications, built for BMW vacuum system service where stable vacuum supply is required. It includes a seal and uses a straight, single-connector design for direct replacement service on listed BMW models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for petrol engines\u003c\/li\u003e\n\u003cli\u003eStraight housing design with 1 connector\u003c\/li\u003e\n\u003cli\u003eSupplied with seal for service replacement\u003c\/li\u003e\n\u003cli\u003eCross-references OE part numbers 7519457 and 11667519457\u003c\/li\u003e\n\u003cli\u003eTechnical information reference: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eBuilt by Pierburg, part number 7.24807.31.0 is an emission control vacuum pump used in BMW vacuum system applications. It is specified for petrol fuel type use and is listed with fitment for BMW Z4, 530i, 525i, 525xi, 530xi, 323i, 325i, 325xi, 330i, and 330xi across model years 2006 through 2010, including 2009-2010 BMW Z4 and 2008 BMW 530i with the noted production cutoff. This part number 7.24807.31.0 is a direct service option for vehicles requiring a mechanical vacuum pump with a straight configuration and one connector.\u003c\/p\u003e\u003cp\u003eThis part cross-references OE numbers 7519457 and 11667519457 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns tied to pump wear\u003c\/li\u003e\n\u003cli\u003eService replacement for a leaking pump seal area\u003c\/li\u003e\n\u003cli\u003eRestoration of vacuum support on listed BMW petrol models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the connector count, straight housing shape, and pressure hose connector diameter of 12 mm on the 2009-2010 BMW Z4 application before installation. Match the vehicle against the listed BMW fitment by year and model, and verify the OE reference numbers and Technical Information Number SI 0109-11 during diagnosis and replacement. The included seal supports proper reassembly when the pump is serviced.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE-focused brand in engine management and emission control components. This vacuum pump is built to match the listed application details for BMW vacuum system service and replacement.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934523621557,"sku":"JCJT-7.24807.31.0","price":295.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807310_Fro.jpg?v=1775005102"},{"product_id":"pierburg-7-24807-33-0-vacuum-pump","title":"Pierburg 7.24807.33.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump 7.24807.33.0\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.33.0 is a mechanical vacuum pump for petrol applications in BMW vacuum system service. It is supplied with a seal and features a straight shape with one connector for direct replacement use on the listed vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.33.0\u003c\/li\u003e\n\u003cli\u003eEmission control \/ vacuum system component\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode\u003c\/li\u003e\n\u003cli\u003eFor petrol engines\u003c\/li\u003e\n\u003cli\u003eStraight housing design\u003c\/li\u003e\n\u003cli\u003eOne connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is built for BMW models that rely on engine vacuum for proper brake assist and related vacuum-operated functions. It is a direct-fit service part for applications including BMW 128i, 328i, 328i xDrive, X3, 323i, 528i, Z4, 528i xDrive, X5, 328xi, and 528xi. The 7.24807.33.0 part number is also referenced in aftermarket listings for the same application, including Dorman - HELP 91133 and URO 11667558344.\u003c\/p\u003e\u003cp\u003eCompatible With BMW vacuum system repairs where a mechanical petrol vacuum pump is required, this component supports consistent vacuum supply in the engine bay. Use it when servicing BMW 328i vacuum pump replacement, BMW X3 vacuum pump replacement, or BMW 528i vacuum pump replacement applications covered by the fitment data.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply\u003c\/li\u003e\n\u003cli\u003eBrake assist concerns related to vacuum loss\u003c\/li\u003e\n\u003cli\u003eVacuum pump leakage at the mounting surface\u003c\/li\u003e\n\u003cli\u003eVacuum system faults on petrol BMW engines\u003c\/li\u003e\n\u003cli\u003eService replacement for worn mechanical pump assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm engine code and vehicle fitment before installation. Replace the seal during service, and inspect the mating surface, vacuum line routing, and connector condition before reassembly. Follow the vehicle service procedure and the Pierburg technical reference SI 0109-11 for installation details.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and vacuum system components. This part is manufactured to support the fitment and service requirements of the listed BMW applications.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicles\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2008-2013 BMW 128i, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2013 BMW 328i, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2013 BMW 328i xDrive, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 BMW X3, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 BMW 323i, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2011 BMW 528i, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 BMW Z4, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 BMW 528i xDrive, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 BMW X5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2008 BMW 328xi, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008 BMW 528xi, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934524047541,"sku":"JCJT-7.24807.33.0","price":173.27,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807330_Fro.jpg?v=1775005103"},{"product_id":"pierburg-7-24807-34-0-vacuum-pump","title":"Pierburg 7.24807.34.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for BMW Petrol Engines\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.34.0 vacuum pump is a mechanical emission control component for petrol-powered BMW applications. It is built with two connectors and includes a seal, making it a direct-fit service part for restoring vacuum supply in supported vehicles.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24807.34.0\u003c\/li\u003e\n\u003cli\u003eCategory: Emission Control \u0026gt; Vacuum System\u003c\/li\u003e\n\u003cli\u003eFuel type: Petrol\u003c\/li\u003e\n\u003cli\u003eOperating mode: Mechanical\u003c\/li\u003e\n\u003cli\u003eNumber of connectors: 2\u003c\/li\u003e\n\u003cli\u003eShape: Straight\u003c\/li\u003e\n\u003cli\u003eIncludes seal\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication and Fitment\u003c\/h2\u003e\u003cp\u003eCompatible with BMW vacuum pump applications across multiple turbocharged petrol models. Fits 2012-2014 BMW 640i, 2013-2014 BMW 640i Gran Coupe, 2013-2014 BMW X1, 2011-2014 BMW X3, 2011-2014 BMW X6, 2011-2013 BMW 135i, 2013 BMW 135is, 2011-2013 BMW 335i, 2011-2013 BMW 335i xDrive, 2011-2013 BMW 535i, 2010-2013 BMW 535i GT, 2011-2013 BMW 535i GT xDrive, 2011-2013 BMW 535i xDrive, 2011-2013 BMW X5, and 2012 BMW 530i to 03\/31\/2012.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - HELP 91145 for the same application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for petrol engine emission control systems\u003c\/li\u003e\n\u003cli\u003eTwo-connector configuration for supported BMW installations\u003c\/li\u003e\n\u003cli\u003eStraight housing layout for OE-style replacement fitment\u003c\/li\u003e\n\u003cli\u003eSupplied with seal for service replacement\u003c\/li\u003e\n\u003cli\u003eDirect reference part: Pierburg 7.24807.34.0\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in the engine vacuum system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability concerns on supported BMW petrol models\u003c\/li\u003e\n\u003cli\u003eEmission control system faults tied to vacuum pump wear\u003c\/li\u003e\n\u003cli\u003eOil seepage or sealing issues at the pump mounting point\u003c\/li\u003e\n\u003cli\u003eService replacement for a worn or failing mechanical vacuum pump\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify connector count, pump shape, and engine application before installation. Use the included seal during service, and confirm the vehicle matches the listed BMW fitment by model year and engine configuration. The part number 7.24807.34.0 should be matched against the original unit or service documentation before replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is a recognized OE supplier in engine management and emission control components. This vacuum pump is identified with Technical Information Number SI 0109-11 and is built for the listed BMW petrol applications.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934524178613,"sku":"JCJT-7.24807.34.0","price":259.22,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807340_Ang_39fb80b2-61c8-4118-b0c5-f3fd03631e78.jpg?v=1775005103"},{"product_id":"pierburg-7-24807-75-0-vacuum-pump","title":"Pierburg 7.24807.75.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump for Audi, Porsche, and Volkswagen\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24807.75.0 is a mechanical vacuum pump for petrol applications in select Audi, Porsche, and Volkswagen vehicles. It is built for direct replacement use in emission control and vacuum system service, with fitment coverage across multiple Audi A4, A5, A6, A7, A8, Q5, Q7, S4, S5, SQ5, Porsche Cayenne, Porsche Panamera, and Volkswagen Touareg applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eMechanical vacuum pump for petrol engines\u003c\/li\u003e\n\u003cli\u003eSingle connector design\u003c\/li\u003e\n\u003cli\u003eStraight configuration\u003c\/li\u003e\n\u003cli\u003eSupplied without gasket or seal\u003c\/li\u003e\n\u003cli\u003ePierburg part number 7.24807.75.0\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump, part number 7.24807.75.0, is used in the vacuum system to support engine operation in vehicles that rely on mechanical vacuum generation. It cross-references OE-style applications such as 06E145100AA and 06E145100M for the same application. Fitment includes 2005-2018 Audi A6 Quattro, 2006-2016 Audi A6, 2008-2016 Audi A5 Quattro, 2009-2017 Audi Q5, 2011-2018 Porsche Cayenne, and 2011-2016 Volkswagen Touareg, along with additional Audi A4, A7, A8, S4, S5, SQ5, Q7, and Porsche Panamera coverage. The straight body style and single connector layout make it a direct-match service part for the listed vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestoring vacuum supply in petrol engine systems\u003c\/li\u003e\n\u003cli\u003eAddressing low vacuum conditions that affect brake assist\u003c\/li\u003e\n\u003cli\u003eReplacing a worn or leaking mechanical vacuum pump\u003c\/li\u003e\n\u003cli\u003eCorrecting vacuum-related drivability or idle concerns\u003c\/li\u003e\n\u003cli\u003eSupporting emission control system operation on listed applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify OE number, engine configuration, and VIN-specific notes before ordering. Some applications require attention to notes such as straight configuration, without gasket\/seal, or VIN breakpoints including 8K8000001 and 4GB000001. Inspect the mounting surface and related vacuum lines during service, and confirm the replacement matches the original connector layout and pump shape. Use the vehicle-specific service procedure for removal and installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and vacuum system components. This vacuum pump is built to match the listed OE applications and technical reference SI 0109-11 for accurate service replacement.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934524932277,"sku":"JCJT-7.24807.75.0","price":225.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724807750_Ang.jpg?v=1775005105"},{"product_id":"pierburg-7-24808-05-0-vacuum-pump","title":"Pierburg 7.24808.05.0 Vacuum Pump","description":"\u003ch2\u003ePierburg 7.24808.05.0 Electric Vacuum Pump\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24808.05.0 is an electric vacuum pump for diesel applications, built with a straight shape, one connector, and a seal ring for service replacement. It is a direct-fit emission control vacuum system component for select Volkswagen Golf, Jetta, and Beetle models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eElectric vacuum pump for diesel engine vacuum system service\u003c\/li\u003e\n\u003cli\u003eStraight housing design with 1 connector\u003c\/li\u003e\n\u003cli\u003eIncludes seal ring for sealing at installation\u003c\/li\u003e\n\u003cli\u003eTechnical Information Number: SI 0109-11\u003c\/li\u003e\n\u003cli\u003eCross-reference: Dorman - HELP 91018\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump, part number 7.24808.05.0, is used in emission control and vacuum system applications where stable vacuum supply is required on diesel vehicles. It is listed for Volkswagen Golf, Volkswagen Jetta, and Volkswagen Beetle applications, including 1999 Volkswagen Golf and 1999 Volkswagen Jetta with OE No. 038145101B. Interchange references include 038145101A and 038145101B, making this a practical OE-style replacement for the specified vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply in the emission control system\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability or control issues on diesel engines\u003c\/li\u003e\n\u003cli\u003eReplacement needs for a worn or failing electric vacuum pump\u003c\/li\u003e\n\u003cli\u003eSealing concerns at the pump mounting point when the original seal is no longer serviceable\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the OE number and connector layout before installation. This pump is specified with one connector and a straight shape, so confirm the mounting location and routing on the vehicle before replacing the original unit. Use the included seal ring during installation and follow Technical Information Number SI 0109-11 for application-specific service details.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and emission control components. This part number 7.24808.05.0 is built to match the listed diesel Volkswagen applications and OE cross-references for accurate replacement selection.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934525030581,"sku":"JCJT-7.24808.05.0","price":271.9,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724808050_Fro.jpg?v=1775005105"},{"product_id":"pierburg-7-24808-12-0-vacuum-pump","title":"Pierburg 7.24808.12.0 Vacuum Pump","description":"\u003ch2\u003ePierburg Vacuum Pump 7.24808.12.0\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.24808.12.0 is a mechanical vacuum pump for diesel emission control and vacuum system service. It is built with one connector, a straight shape, and includes a seal for OE-style replacement on select Volkswagen and Audi diesel applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Pierburg\u003c\/li\u003e\n\u003cli\u003ePart number: 7.24808.12.0\u003c\/li\u003e\n\u003cli\u003eMechanical operating mode for diesel engines\u003c\/li\u003e\n\u003cli\u003eOne connector with straight housing design\u003c\/li\u003e\n\u003cli\u003eIncludes seal\u003c\/li\u003e\n\u003cli\u003eCross-references OE numbers 03L145100 and 03L145100F\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Pierburg vacuum pump is designed for diesel-powered vehicles that rely on engine vacuum for emission control and related system operation. The 7.24808.12.0 is a direct-fit style replacement for select Volkswagen Tiguan, Volkswagen Jetta, Volkswagen Golf, Volkswagen Passat, Volkswagen Beetle, Audi A3, Audi A3 Quattro, Audi Q3, and Audi Q3 Quattro applications. It cross-references OE numbers 03L145100 and 03L145100F for the same application. If you are replacing a worn vacuum pump on a Volkswagen Tiguan diesel or an Audi Q3 diesel, this part number helps match the original configuration.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply in diesel engine systems\u003c\/li\u003e\n\u003cli\u003eVacuum-related emission control faults\u003c\/li\u003e\n\u003cli\u003eHard brake pedal feel caused by vacuum loss\u003c\/li\u003e\n\u003cli\u003eOil seepage at the pump mounting area when the seal is worn\u003c\/li\u003e\n\u003cli\u003eDriveability issues tied to vacuum-operated components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify OE number 03L145100 or 03L145100F before ordering. Confirm the engine is diesel and match the connector count and straight housing layout to the original pump. Inspect the mounting surface and replace the seal during installation. Follow the vehicle service procedure and the technical information reference SI 0109-11 for application-specific details.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and vacuum system components. This vacuum pump is built to OE-style specifications for the listed Volkswagen and Audi diesel applications.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934525128885,"sku":"JCJT-7.24808.12.0","price":219.52,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_724808120_Fro.jpg?v=1775005105"},{"product_id":"pierburg-7-28098-04-0-diverter-valve","title":"Pierburg 7.28098.04.0 Diverter Valve","description":"\u003ch2\u003ePierburg Diverter Valve for Audi, Volkswagen, and Porsche\u003c\/h2\u003e\u003cp\u003eThe Pierburg 7.28098.04.0 is an electric diverter valve built for emission control vacuum system applications. It uses a 12-volt switch valve design to manage vacuum-actuated operation in the intake and boost control system, helping maintain proper engine response on supported Audi, Volkswagen, and Porsche platforms.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eElectric operating mode for controlled valve actuation\u003c\/li\u003e\n\u003cli\u003e12V switch valve design\u003c\/li\u003e\n\u003cli\u003eEmission control vacuum system component\u003c\/li\u003e\n\u003cli\u003eCross-references Pierburg 7.28098.04.0 for OE-style replacement needs\u003c\/li\u003e\n\u003cli\u003eInterchanges with select OE and aftermarket part numbers for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eApplication Details\u003c\/h2\u003e\u003cp\u003eCompatible With Audi A8 Quattro, Audi S8, Audi Q5, Audi RS5, Audi Q7, Audi A3 Quattro, Audi TT Quattro, Volkswagen Golf R, Volkswagen R32, Volkswagen Beetle, Volkswagen Golf, Volkswagen Jetta, Volkswagen Phaeton, Volkswagen EuroVan, and Porsche Cayenne applications listed below. This Pierburg 7.28098.04.0 diverter valve is used on vehicles with specific OE references such as 037906283D and related interchange numbers.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2017-2018 Porsche Cayenne, N\/A, for vehicles with start-stop function and brake energy recovery\u003c\/li\u003e\n\u003cli\u003eFits 2014-2017 Audi S8, N\/A, to VIN # A010000\u003c\/li\u003e\n\u003cli\u003eFits 2014-2016 Audi A8 Quattro, N\/A, to VIN # A010000\u003c\/li\u003e\n\u003cli\u003eFits 2013-2016 Audi Q5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2016 Audi RS5, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2013-2015 Audi Q7, N\/A, with OE No. 037906283D\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Volkswagen Golf R, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2009 Audi S8, N\/A, from VIN # 4E3000001\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Volkswagen Golf, N\/A, with OE No. 037906283D\u003c\/li\u003e\n\u003cli\u003eFits 1999-2003 Volkswagen EuroVan, N\/A, with OE No. 037906283D\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Valve Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eIrregular boost control behavior\u003c\/li\u003e\n\u003cli\u003eVacuum switching faults in the emission control system\u003c\/li\u003e\n\u003cli\u003eDriveability issues tied to a failing diverter valve\u003c\/li\u003e\n\u003cli\u003eOE-number mismatch during replacement on Audi and Volkswagen turbo applications\u003c\/li\u003e\n\u003cli\u003eStart-stop and brake energy recovery system service needs on select Porsche Cayenne models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the OE number, VIN break, and engine configuration before ordering. This part number, 7.28098.04.0, is listed with multiple interchange references, so matching the original valve type and voltage is important for correct installation. Confirm the vehicle uses the specified vacuum system and, where noted, the OE number 037906283D or VIN cutoff listed in the fitment data.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003ePierburg is an established OE supplier in engine management and emission control components. The 7.28098.04.0 diverter valve is built to the listed technical specification: electric operating mode, switch valve type, and 12V operation.\u003c\/p\u003e","brand":"Pierburg","offers":[{"title":"Default Title","offer_id":43934525391029,"sku":"JCJT-7.28098.04.0","price":60.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/HL_728098040_Fro.jpg?v=1775005106"},{"product_id":"dorman-904-214-vacuum-pump","title":"Dorman 904-214 Vacuum Pump","description":"\u003ch2\u003eDorman 904-214 Vacuum Pump Overview\u003c\/h2\u003e\u003cp\u003eDorman 904-214 is a replacement vacuum pump built to match the fit and function of the original equipment unit. It uses a plastic housing and an electric motor drive to support vacuum-operated vehicle functions with dependable operation. This vacuum pump is listed for applications including Ford F-250 Super Duty, Ford F-350 Super Duty, Ford Excursion, and select Dodge Ram 2500 and Ram 3500 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for OE-style fit and function\u003c\/li\u003e\n\u003cli\u003eElectric motor drive for vacuum system operation\u003c\/li\u003e\n\u003cli\u003ePlastic housing for lightweight construction\u003c\/li\u003e\n\u003cli\u003eBarbed connector design\u003c\/li\u003e\n\u003cli\u003eVacuum pump inlet: 1\/4 in\u003c\/li\u003e\n\u003cli\u003eVacuum pump outlet: 1\/8 in\u003c\/li\u003e\n\u003cli\u003ePackage contents: pump assembly and 3 rubber grommets\u003c\/li\u003e\n\u003cli\u003ePart number: 904-214\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is engineered as a replacement for the original equipment pump on vacuum-controlled vehicle systems. It is built from durable materials and configured with a barbed connector, 1\/4 in inlet, and 1\/8 in outlet for service in electrically driven vacuum applications. The 904-214 is a practical choice for owners servicing Ford F-250 Super Duty and Ford F-350 Super Duty trucks, as well as Ford Excursion and select Dodge Ram 2500 and Ram 3500 models that use an electrically driven vacuum pump.\u003c\/p\u003e\u003cp\u003eThis part cross-references Standard Ignition VCP112 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It May Help Resolve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply to vehicle-operated systems\u003c\/li\u003e\n\u003cli\u003eInconsistent operation of vacuum-dependent components\u003c\/li\u003e\n\u003cli\u003eVacuum pump noise or reduced pump performance\u003c\/li\u003e\n\u003cli\u003eFailure of the original electrically driven vacuum pump\u003c\/li\u003e\n\u003cli\u003eService needs on Ford F-250 Super Duty, Ford F-350 Super Duty, and Ford Excursion vacuum systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses an electrically driven vacuum pump before ordering. Confirm the inlet and outlet sizes, connector style, and mounting location match the original unit. This pump assembly includes 3 rubber grommets, and the listing does not include a pulley, gasket, or seal. Use the vehicle service information to confirm routing and electrical connection details during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman replacement parts are built to match OE fit and function for the listed applications. Part number 904-214 is intended for direct replacement service on supported Ford and Dodge vacuum pump applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327312949429,"sku":"BKLB-904-214","price":124.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904214_Fro.jpg?v=1775011763"},{"product_id":"dorman-904-335-vacuum-pump-repair-kit","title":"Dorman 904-335 Vacuum Pump Repair Kit","description":"\u003ch2\u003eDorman 904-335 Vacuum Pump Repair Kit\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump repair kit is built to reseal the engine vacuum pump with the gaskets and seals needed for a proper service. It is made from quality materials to match original equipment fit and performance for Dodge Ram 2500 and Dodge Ram 3500 applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSeal kit for vacuum pump resealing\u003c\/li\u003e\n\u003cli\u003eMade to match OE fit and performance\u003c\/li\u003e\n\u003cli\u003eThoroughly tested for quality\u003c\/li\u003e\n\u003cli\u003eDirect service part for vacuum pump repair\u003c\/li\u003e\n\u003cli\u003eFits 1994-2002 Dodge Ram 2500 and 1994-2002 Dodge Ram 3500\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eUse Dorman 904-335 when servicing a leaking or worn engine vacuum pump on Dodge Ram 2500 and Dodge Ram 3500 trucks. The kit includes the gaskets and seals needed to restore the pump’s sealing surfaces, helping maintain vacuum system integrity after repair. This part cross-references Mopar 5140342AA for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum pump oil seepage at the seal surfaces\u003c\/li\u003e\n\u003cli\u003eLoss of vacuum caused by deteriorated gaskets\u003c\/li\u003e\n\u003cli\u003eService issues from hardened or damaged seals\u003c\/li\u003e\n\u003cli\u003eRepeat leaks after vacuum pump disassembly\u003c\/li\u003e\n\u003cli\u003eVacuum pump reseal needs during engine maintenance\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eClean all mating surfaces before assembly and inspect the vacuum pump housing for wear, scoring, or damage. Replace the seals during pump service and verify proper seating before reinstallation. Confirm vehicle fitment by year and model before ordering; this kit fits 1994-2002 Dodge Ram 2500 and 1994-2002 Dodge Ram 3500.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman tests this repair kit for quality and builds it to match original equipment fit and performance. Part number 904-335 is engineered as a direct reseal solution for vacuum pump service on the listed Dodge Ram applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327349059765,"sku":"BKKY-904-335","price":87.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904335_Ang.jpg?v=1775011782"},{"product_id":"dorman-904-809-vacuum-pump","title":"Dorman 904-809 Vacuum Pump","description":"\u003ch2\u003eDorman 904-809 Vacuum Pump for Dodge Trucks\u003c\/h2\u003e\u003cp\u003eDorman 904-809 is a direct replacement vacuum pump built to match the fit and function of the original equipment unit. It uses a metal housing and gear-drive design to support vacuum-operated vehicle functions on select Dodge D250, D350, W250, and W350 trucks from 1989-1991.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for OE-style fit and function\u003c\/li\u003e\n\u003cli\u003eMetal housing for durable service\u003c\/li\u003e\n\u003cli\u003eGear-drive vacuum pump design\u003c\/li\u003e\n\u003cli\u003eBarbed connector style\u003c\/li\u003e\n\u003cli\u003eRelief valve included\u003c\/li\u003e\n\u003cli\u003eInlet and outlet sizes: 3\/8 in, 1\/2 in, 5\/8 in, 3\/4 in, and 1 in\u003c\/li\u003e\n\u003cli\u003ePackage contents: pump assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is built for mechanically driven applications and is intended to restore vacuum supply for systems that rely on engine vacuum. It is a practical replacement for Dodge D250 and Dodge W350 vacuum pump service, as well as D350 and W250 models in the same 1989-1991 range. The part number 904-809 is also a useful reference when sourcing the correct replacement for these trucks.\u003c\/p\u003e\u003cp\u003eThis part cross-references Cardone Reman 64-1300 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply to vehicle systems\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability or accessory operation issues\u003c\/li\u003e\n\u003cli\u003eFailure of the original mechanically driven pump\u003c\/li\u003e\n\u003cli\u003eLoss of vacuum support in older Dodge truck applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1989-1991 Dodge D250, N\/A; mechanically driven vacuum pump for fitment.\u003c\/li\u003e\n\u003cli\u003eFits 1989-1991 Dodge D350, N\/A; mechanically driven vacuum pump for fitment.\u003c\/li\u003e\n\u003cli\u003eFits 1989-1991 Dodge W250, N\/A; mechanically driven vacuum pump for fitment.\u003c\/li\u003e\n\u003cli\u003eFits 1989-1991 Dodge W350, N\/A; mechanically driven vacuum pump for fitment.\u003c\/li\u003e\n\u003cli\u003eVerify inlet and outlet hose sizing before installation.\u003c\/li\u003e\n\u003cli\u003eGasket or seal is not included, and pulley is not included.\u003c\/li\u003e\n\u003cli\u003eConfirm the gear-drive configuration matches the original pump before replacement.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this replacement pump to match original equipment fit and function using durable materials for reliable operation. The relief valve is included to support stable vacuum performance in the vehicle’s vacuum-operated systems.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327435632821,"sku":"BKLB-904-809","price":127.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904809_Fro.jpg?v=1775011875"},{"product_id":"dorman-904-810-vacuum-pump","title":"Dorman 904-810 Vacuum Pump","description":"\u003ch2\u003eDorman 904-810 Vacuum Pump for Ram HD\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is a direct-fit replacement for mechanically driven vacuum pump applications on select Dodge Ram 2500 and Ram 3500 trucks. Built with a metal housing, pulley, gear drive, and integrated relief valve, it restores vacuum supply for vehicle systems that depend on consistent pump output.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for OE fit and function\u003c\/li\u003e\n\u003cli\u003eMetal housing for durable service\u003c\/li\u003e\n\u003cli\u003eGear-drive design for mechanically driven applications\u003c\/li\u003e\n\u003cli\u003ePulley included for proper installation\u003c\/li\u003e\n\u003cli\u003eGasket or seal included\u003c\/li\u003e\n\u003cli\u003eBarbed connector with multiple inlet and outlet sizes: 3\/8 in, 1\/2 in, 5\/8 in, 3\/4 in, and 1 in\u003c\/li\u003e\n\u003cli\u003eRelief valve included for controlled operation\u003c\/li\u003e\n\u003cli\u003ePackage contents: pump assembly and gasket\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman 904-810 is engineered to match the fit and function of the original equipment vacuum pump on 1994-2002 Dodge Ram 2500 and 1994-2002 Dodge Ram 3500 models. It is built from durable materials and uses a gear-drive system to support reliable operation of vacuum-operated vehicle functions. This part cross-references Cardone New 90-1309 and Cardone Reman 64-1302 for the same application.\u003c\/p\u003e\u003cp\u003eFor Ram HD trucks that rely on a mechanically driven vacuum source, this replacement pump helps restore stable vacuum delivery and consistent system performance. The Dorman 904-810 is a practical choice when replacing a worn or failing pump on Dodge Ram 2500 and Ram 3500 applications.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply from a worn pump\u003c\/li\u003e\n\u003cli\u003eInconsistent operation of vacuum-operated vehicle functions\u003c\/li\u003e\n\u003cli\u003eNoisy or inefficient mechanically driven pump performance\u003c\/li\u003e\n\u003cli\u003eVacuum leaks related to pump housing or seal wear\u003c\/li\u003e\n\u003cli\u003eReduced system response caused by pump failure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eCompatible with 1994-2002 Dodge Ram 2500 and 1994-2002 Dodge Ram 3500 applications listed for mechanically driven vacuum pump fitment. Verify inlet and outlet hose sizing before installation, and confirm the gear-drive configuration matches the original unit. The included gasket or seal should be used during installation to help ensure a proper seal.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eThis replacement vacuum pump is built to match OE fit and function using durable materials for reliable service. Dorman 904-810 is intended for direct replacement use on the specified Dodge Ram HD applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327436091573,"sku":"BKLB-904-810","price":242.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904810_Fro.jpg?v=1775011875"},{"product_id":"dorman-904-815-vacuum-pump-repair-kit","title":"Dorman 904-815 Vacuum Pump Repair Kit","description":"\u003ch2\u003eDorman 904-815 Vacuum Pump Repair Kit\u003c\/h2\u003e\u003cp\u003eRestore vacuum pump sealing performance with the Dorman 904-815 vacuum pump repair kit. It includes the gaskets and seals needed to reseal the engine vacuum pump on select Volvo applications, helping address leaks and maintain proper vacuum system operation.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDirect-fit repair kit for engine vacuum pump resealing\u003c\/li\u003e\n\u003cli\u003eMade from plastic and rubber components in black finish\u003c\/li\u003e\n\u003cli\u003eIncludes one-way valve, O-rings, and M6 x 1.25 screws\u003c\/li\u003e\n\u003cli\u003eO-ring sizes cover 20.5 mm, 55 mm, and 95 mm inside diameters\u003c\/li\u003e\n\u003cli\u003eRound O-ring profile for OE-style sealing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Coverage\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2011-2016 Volvo S60, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2015-2016 Volvo V60, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2010-2016 Volvo XC60, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2015 Volvo S80, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2015 Volvo XC70, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 Volvo XC90, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2010 Volvo V70, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThis part cross-references Genu 31401556 for the same application.\u003c\/p\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman 904-815 is built for Volvo vehicles that need a vacuum pump reseal rather than a full pump replacement. The kit is engineered to match original equipment fit and performance, using quality materials selected for sealing reliability and consistent operation. It is a practical service solution for Volvo S60, V60, XC60, S80, XC70, XC90, and V70 models within the listed year ranges.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVacuum pump oil seepage at the gasket or seal surfaces\u003c\/li\u003e\n\u003cli\u003eLoss of vacuum from worn O-rings or sealing rings\u003c\/li\u003e\n\u003cli\u003eVacuum pump housing leaks after service or disassembly\u003c\/li\u003e\n\u003cli\u003eReduced brake booster vacuum caused by pump sealing failure\u003c\/li\u003e\n\u003cli\u003eVacuum system performance issues tied to deteriorated pump seals\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eClean all mating surfaces thoroughly before assembly and inspect the pump housing for wear, scoring, or damage. Verify O-ring placement and seal orientation during reassembly, and torque fasteners evenly to help maintain a uniform seal. Confirm the vehicle application against the listed Volvo fitment before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman states that this repair kit has been thoroughly tested for quality and is made to match original equipment fit and performance. The components are built to support a proper reseal of the engine vacuum pump on the specified Volvo applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327436288181,"sku":"BKKY-904-815","price":82.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904815_Fro.jpg?v=1775011876"},{"product_id":"dorman-904-817-vacuum-pump","title":"Dorman 904-817 Vacuum Pump","description":"\u003ch2\u003eDorman 904-817 Vacuum Pump for Volkswagen and Audi\u003c\/h2\u003e\u003cp\u003eDorman 904-817 is a replacement vacuum pump built to match the fit and function of the original equipment unit. It uses a durable aluminum housing and a gear-drive design to support vacuum-operated vehicle functions on select Volkswagen and Audi models.\u003c\/p\u003e\u003cp\u003eCompatible with 2006-2018 Volkswagen Beetle, Jetta, Golf, Passat, and Golf SportWagen applications, plus select Audi TT RS Quattro models, this vacuum pump is a direct-fit service part for mechanically driven vacuum pump systems. The Dorman 904-817 vacuum pump is a practical OE-style replacement for diagnosing or repairing vacuum loss concerns.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement vacuum pump for select Volkswagen and Audi vehicles\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eGear-drive pump design\u003c\/li\u003e\n\u003cli\u003eBarbed connector for the vacuum line connection\u003c\/li\u003e\n\u003cli\u003e1\/2 in inlet size\u003c\/li\u003e\n\u003cli\u003eNo pulley included\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo relief valve included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is engineered to match the original equipment pump’s fit and function, making it a direct replacement for mechanically driven vacuum pump systems. It is commonly used on Volkswagen Beetle, Jetta, Golf, Passat, and Golf SportWagen models, as well as Audi TT RS Quattro applications listed in the fitment data. Part number 904-817 is also cross-referenced to Standard Ignition VCP154 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Repair\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply\u003c\/li\u003e\n\u003cli\u003eBrake assist concerns related to vacuum loss\u003c\/li\u003e\n\u003cli\u003eVacuum-operated system performance issues\u003c\/li\u003e\n\u003cli\u003eOil leakage or wear from a failing pump assembly\u003c\/li\u003e\n\u003cli\u003eDrive-related pump noise or reduced pump output\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm the barbed connector style, 1\/2 in inlet, and the absence of a pulley, gasket, seal, and relief valve against the original part. Because fitment varies by engine and configuration, compare the existing pump to the vehicle application before installation. Professional installation is recommended for proper sealing and vacuum system operation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman builds this replacement pump to match OE fit and function using durable materials for reliable service. It is intended as a service replacement for select Volkswagen and Audi vacuum pump applications, including models such as the Volkswagen Jetta, Volkswagen Passat, and Audi TT RS Quattro.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327438287029,"sku":"BKKY-904-817","price":276.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904817_Fro_0ba13448-ae55-49b2-b316-06c8d301749c.jpg?v=1775011876"},{"product_id":"dorman-904-819-vacuum-pump","title":"Dorman 904-819 Vacuum Pump","description":"\u003ch2\u003eVacuum Pump for Mini Cooper and Cooper Paceman\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is a direct-fit replacement for mechanically driven vacuum pump applications on select Mini models. Built with an aluminum housing and barbed inlet and outlet connections, it restores vacuum supply for vehicle systems that depend on consistent pump operation.\u003c\/p\u003e\u003cp\u003eCompatible with 2006-2015 Mini Cooper and 2013-2016 Mini Cooper Paceman applications, this Dorman 904-819 replacement is made to match the original equipment pump’s fit and function. It is a practical choice when the factory pump shows wear, leakage, or reduced vacuum output.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for select Mini vehicles\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eGear-driven design for mechanically driven applications\u003c\/li\u003e\n\u003cli\u003eBarbed connector style for vacuum line attachment\u003c\/li\u003e\n\u003cli\u003e1\/4 in inlet and 1\/8 in outlet dimensions\u003c\/li\u003e\n\u003cli\u003eNo pulley, gasket, seal, or relief valve included\u003c\/li\u003e\n\u003cli\u003eDorman 904-819 for OE-style fit and function\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman 904-819 is engineered as a replacement vacuum pump for Mini Cooper and Mini Cooper Paceman models that use a mechanically driven vacuum pump. It is built to match the original pump’s fit and operating role, helping maintain vacuum supply for systems that rely on stable vacuum pressure. The aluminum housing supports dependable service in demanding engine-bay conditions, while the gear-drive configuration aligns with the original mechanical drive setup.\u003c\/p\u003e\u003cp\u003eThis part cross-references BMW OE number 11667556919 for the same application. Use Dorman 904-819 when you need a replacement vacuum pump for 2006-2015 Mini Cooper or 2013-2016 Mini Cooper Paceman vehicles with the correct inlet, outlet, and connector style.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum pressure from a worn or failing pump\u003c\/li\u003e\n\u003cli\u003eVacuum-operated system performance issues\u003c\/li\u003e\n\u003cli\u003eNoise or irregular operation from a mechanically driven pump\u003c\/li\u003e\n\u003cli\u003eOil seepage or housing wear at the original pump\u003c\/li\u003e\n\u003cli\u003eRestoration of factory vacuum supply on Mini Cooper and Cooper Paceman models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm the inlet, outlet, and barbed connector style match the original unit, and transfer any required seals or gaskets from the vehicle if applicable, since they are not included. Inspect the mounting surface and vacuum lines for wear before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eThis Dorman replacement is built from durable materials and follows the original equipment pump’s fit and function for reliable operation. It is intended for direct replacement use on the listed Mini Cooper and Mini Cooper Paceman applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327439204533,"sku":"BKKY-904-819","price":341.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904819_Fro.jpg?v=1775011876"},{"product_id":"dorman-904-820-vacuum-pump","title":"Dorman 904-820 Vacuum Pump","description":"\u003ch2\u003eOE-Style Vacuum Pump for Mini Cooper\u003c\/h2\u003e\u003cp\u003eDorman 904-820 is a mechanically driven vacuum pump built to match the fit and function of the original equipment unit. It is made with an aluminum housing for durable service and uses a gear drive with a barbed connector and 1\/4 in inlet for the specified application.\u003c\/p\u003e\u003cp\u003eFits 2007-2010 Mini Cooper, N\/A. This Dorman 904-820 vacuum pump is a direct replacement choice for Mini Cooper models that use a mechanically driven vacuum pump.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement vacuum pump for the listed Mini Cooper application\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable construction\u003c\/li\u003e\n\u003cli\u003eGear-drive design for mechanically driven operation\u003c\/li\u003e\n\u003cli\u003eBarbed vacuum pump connector with 1\/4 in inlet\u003c\/li\u003e\n\u003cli\u003eReplacement for vacuum-operated vehicle functions that rely on stable vacuum supply\u003c\/li\u003e\n\u003cli\u003ePart number 904-820 for easy identification\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis vacuum pump is engineered to match the original equipment pump’s fit and function on 2007-2010 Mini Cooper models with a mechanically driven vacuum pump. Dorman 904-820 is built from durable materials and is intended to restore proper vacuum supply for systems that depend on consistent pump output. The aluminum housing supports long-term service, while the gear-drive layout and barbed connector reflect the original style of the application. Cross-reference part number: this part cross-references BMW\/Mini OE number 11667570813 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply\u003c\/li\u003e\n\u003cli\u003eVacuum-operated system performance issues\u003c\/li\u003e\n\u003cli\u003eNoise or wear associated with a failing mechanical vacuum pump\u003c\/li\u003e\n\u003cli\u003eLoss of proper operation in vacuum-dependent vehicle functions\u003c\/li\u003e\n\u003cli\u003eReplacement needs for a worn original pump on Mini Cooper models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm connector style, 1\/4 in inlet size, and gear-drive configuration against the original unit. Gasket or seal is not included, and pulley is not included. Because fitment is specific to 2007-2010 Mini Cooper applications, compare the original part number and mounting details before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman replacement parts are built to match original equipment fit and function for the listed application. Part number 904-820 is manufactured for reliable operation in the specified Mini Cooper vacuum pump application.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327439237301,"sku":"BKKY-904-820","price":353.03,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904820_Fro.jpg?v=1775011877"},{"product_id":"dorman-904-821-vacuum-pump","title":"Dorman 904-821 Vacuum Pump","description":"\u003ch2\u003eOE-Style Vacuum Pump Replacement\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is built to match the fit and function of the original equipment unit for vacuum-operated vehicle systems. It is a direct replacement for applications such as BMW 550i, 650i, X5, 750i, 750Li, 760Li, 760i, 545i, 645Ci, 745i, 745Li, and Rolls-Royce Phantom models that use a mechanically driven pump.\u003c\/p\u003e\u003cp\u003ePart number 904-821 uses a gear-drive design with an aluminum housing and barbed connector for a straightforward OE-style replacement. If you are replacing a worn BMW vacuum pump or servicing a mechanically driven vacuum pump on a Rolls-Royce Phantom, this unit restores vacuum supply for critical engine and brake-related functions.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for vacuum-operated vehicle functions\u003c\/li\u003e\n\u003cli\u003eGear-drive pump design\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eBarbed inlet and outlet connections\u003c\/li\u003e\n\u003cli\u003eOE-style fit and function for selected BMW and Rolls-Royce applications\u003c\/li\u003e\n\u003cli\u003ePart number 904-821\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Information\u003c\/h2\u003e\u003cp\u003eDorman 904-821 is a mechanically driven vacuum pump replacement made to match the original equipment pump’s fit and operating role. It features a 1\/2 in inlet, 1\/8 in outlet, and no pulley, gasket or seal, or relief valve included. This part cross-references BMW 11667635657 for the same application. For buyers searching for a BMW vacuum pump replacement or a Rolls-Royce Phantom mechanically driven vacuum pump, this part provides the correct style of service component for the listed vehicles.\u003c\/p\u003e\u003ch2\u003eWhat This Vacuum Pump Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply to engine or accessory systems\u003c\/li\u003e\n\u003cli\u003eBrake assist concerns related to vacuum loss\u003c\/li\u003e\n\u003cli\u003eVacuum-operated function irregularities\u003c\/li\u003e\n\u003cli\u003eNoise or performance issues from a worn mechanical pump\u003c\/li\u003e\n\u003cli\u003eReplacement of a leaking or failing OE vacuum pump\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm connector style, inlet size, and outlet size against the original unit, and inspect the mounting surface and related vacuum lines during installation. Because the gasket or seal is not included, reuse or replacement of sealing components must be handled separately as required by the application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman replacement parts are built to match original equipment fit and function using durable materials for reliable service. Part number 904-821 is intended for direct replacement use on the listed BMW and Rolls-Royce applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327439859893,"sku":"BKKY-904-821","price":492.87,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904821_Fro.jpg?v=1775011877"},{"product_id":"dorman-904-822-vacuum-pump","title":"Dorman 904-822 Vacuum Pump","description":"\u003ch2\u003eVacuum Pump Replacement for BMW Diesel Applications\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is a direct-fit replacement for the original equipment unit on select BMW diesel models. Built with an aluminum housing and a gear-drive design, it restores vacuum supply for engine and vehicle systems that rely on consistent vacuum operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for OE fit and function\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eGear-drive pump design\u003c\/li\u003e\n\u003cli\u003eBarbed vacuum pump connector\u003c\/li\u003e\n\u003cli\u003e1\/2 in vacuum pump inlet\u003c\/li\u003e\n\u003cli\u003ePackage contents: 1 vacuum pump\u003c\/li\u003e\n\u003cli\u003eNo pulley included\u003c\/li\u003e\n\u003cli\u003eNo gasket or seal included\u003c\/li\u003e\n\u003cli\u003eNo relief valve\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman 904-822 is engineered for mechanically driven vacuum pump applications on 2009-2013 BMW X5 and 2009-2011 BMW 335d models. It matches the fit and function of the original equipment pump, making it a practical replacement when the factory unit is worn, leaking, or no longer maintaining proper vacuum. The aluminum construction supports reliable operation in demanding engine bay conditions, while the barbed connector and 1\/2 in inlet support the original vacuum routing layout. If you are searching for a BMW X5 vacuum pump replacement or a BMW 335d mechanically driven vacuum pump, 904-822 is built for those applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references BMW OE number 11667791232 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply to engine-driven systems\u003c\/li\u003e\n\u003cli\u003eVacuum leaks caused by a failing pump housing or internal wear\u003c\/li\u003e\n\u003cli\u003eReduced operation of vacuum-operated vehicle functions\u003c\/li\u003e\n\u003cli\u003eHard-to-diagnose drivability issues tied to weak vacuum output\u003c\/li\u003e\n\u003cli\u003eReplacement needs for mechanically driven BMW diesel vacuum pump service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm connector style, inlet size, and mounting configuration against the original unit. Because a gasket or seal is not included, inspect the existing sealing components and replace them as needed during installation. Check surrounding vacuum lines for cracks, loose connections, or contamination before returning the vehicle to service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman replacement parts are built to match original equipment fit and function using durable materials for dependable service. Part number 904-822 is intended for 2009-2013 BMW X5 and 2009-2011 BMW 335d applications listed above.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327440089269,"sku":"BKKY-904-822","price":472.31,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904822_Fro.jpg?v=1775011877"},{"product_id":"dorman-904-824-vacuum-pump","title":"Dorman 904-824 Vacuum Pump","description":"\u003ch2\u003eDorman 904-824 Vacuum Pump for GM Vans\u003c\/h2\u003e\u003cp\u003eDorman 904-824 is a replacement electric vacuum pump built to match the original equipment pump’s fit and function. It is made with durable plastic housing and a relief valve for dependable operation of vacuum-operated vehicle systems. Compatible With 2006-2016 Chevrolet Express 2500, 2006-2016 Chevrolet Express 3500, 2006-2016 GMC Savana 2500, and 2006-2016 GMC Savana 3500 with electrically driven applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement vacuum pump for vacuum system service\u003c\/li\u003e\n\u003cli\u003eElectric motor drive for electrically driven applications\u003c\/li\u003e\n\u003cli\u003ePlastic housing for lightweight, durable construction\u003c\/li\u003e\n\u003cli\u003eRelief valve included for system protection\u003c\/li\u003e\n\u003cli\u003eMale elliptical connector with 2 terminals and pin-type connection\u003c\/li\u003e\n\u003cli\u003eBarbed vacuum pump connector with 3\/16 in inlet and 1\/4 in outlet\u003c\/li\u003e\n\u003cli\u003eFits Chevrolet Express and GMC Savana vans across 2006-2016 model years\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is engineered as a direct replacement for the original equipment unit, with the same fit and function expected in GM van vacuum systems. Part number 904-824 is built for electrically driven operation and uses a barbed connector layout with a single vacuum port to support vacuum-operated vehicle functions. The design includes a relief valve and a durable plastic housing to help maintain consistent performance in service. This part cross-references Cardone Reman 64-1504 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Vacuum Pump Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply to vehicle-operated systems\u003c\/li\u003e\n\u003cli\u003eVacuum pump noise or inconsistent pump operation\u003c\/li\u003e\n\u003cli\u003eFaults related to an inoperative electric vacuum pump\u003c\/li\u003e\n\u003cli\u003eReduced performance in vacuum-dependent vehicle functions\u003c\/li\u003e\n\u003cli\u003eReplacement needs on high-mileage Chevrolet Express and GMC Savana vans\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify connector style, inlet and outlet sizing, and electrical terminal layout before installation. This pump does not include mounting hardware, a gasket, or a seal, so confirm the vehicle’s service requirements before beginning the repair. Match the application to electrically driven GM van configurations only, and compare the original unit to Dorman 904-824 before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this replacement pump to match original equipment fit and function using durable materials for reliable service. It is intended for direct replacement use in supported Chevrolet Express and GMC Savana applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327440777397,"sku":"BKKY-904-824","price":173.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904824_Fro.jpg?v=1775011878"},{"product_id":"dorman-904-828-vacuum-pump","title":"Dorman 904-828 Vacuum Pump","description":"\u003ch2\u003eDorman 904-828 Vacuum Pump for BMW\u003c\/h2\u003e\u003cp\u003eDorman 904-828 is a belt-driven vacuum pump built to match the fit and function of the original equipment unit. It uses a durable aluminum housing, a barbed connector, and an included gasket to support reliable vacuum operation in BMW applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for mechanically driven systems\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eRelief valve included\u003c\/li\u003e\n\u003cli\u003eBarbed vacuum pump connector with 0.613 in inlet diameter\u003c\/li\u003e\n\u003cli\u003eBelt drive design for OE-style operation\u003c\/li\u003e\n\u003cli\u003eGasket included; pulley and mounting hardware not included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump, part number 904-828, is engineered as a replacement for the original equipment pump used on select BMW models. It is built for mechanically driven vacuum pump applications and supports vacuum-operated vehicle functions that depend on consistent pump output. The aluminum housing and relief valve help provide dependable operation in demanding engine bay conditions. This part cross-references URO 11667558344 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With BMW 128i, 2008-2013; BMW 328i, 2007-2013; BMW 328i xDrive, 2009-2013; BMW X3, 2010-2012; BMW X5, 2007-2012; BMW 323i, 2006-2011; BMW 528i, 2009-2011; BMW Z4, 2003-2011; BMW 528i xDrive, 2009-2010; BMW 328xi, 2007-2008; and BMW 528xi, 2008.\u003c\/p\u003e\u003ch2\u003eWhat It Is Used For\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply in mechanically driven BMW vacuum pump systems\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability or brake assist concerns tied to pump wear\u003c\/li\u003e\n\u003cli\u003eOil seepage or housing wear at the original pump assembly\u003c\/li\u003e\n\u003cli\u003eReplacement after pump noise, reduced output, or internal valve issues\u003c\/li\u003e\n\u003cli\u003eRestoring vacuum-operated functions on BMW 128i, 328i, X3, X5, and Z4 models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm the 0.613 in inlet size, barbed connector style, and belt drive layout match the original unit. The package includes a gasket; mounting hardware and pulley are not included, so reuse or source any required external components as needed. Always inspect the mounting surface and vacuum lines before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman builds this replacement pump to match OE fit and function for the listed BMW applications. The aluminum construction, relief valve, and included gasket support dependable service in vacuum system repair work.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327440974005,"sku":"BKKY-904-828","price":335.33,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904828_Fro.jpg?v=1775011878"},{"product_id":"dorman-904-835-vacuum-pump","title":"Dorman 904-835 Vacuum Pump","description":"\u003ch2\u003eDorman 904-835 Vacuum Pump for Volkswagen\u003c\/h2\u003e\u003cp\u003eDorman 904-835 is a direct replacement vacuum pump built to match the fit and function of the original equipment unit. It uses a gear drive, aluminum housing, and a barbed connector to support vacuum-operated vehicle functions with reliable operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement vacuum pump for OE-style fit and function\u003c\/li\u003e\n\u003cli\u003eGear-driven design for mechanically driven vacuum pump applications\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable service\u003c\/li\u003e\n\u003cli\u003eRelief valve included\u003c\/li\u003e\n\u003cli\u003e0.615 in inlet and 0.615 in inside diameter\u003c\/li\u003e\n\u003cli\u003eBarbed vacuum pump connector\u003c\/li\u003e\n\u003cli\u003eCompatible With 2012-2018 Volkswagen Beetle, mechanically driven vacuum pump\u003c\/li\u003e\n\u003cli\u003eCompatible With 2014-2015 Volkswagen Golf, mechanically driven vacuum pump\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is engineered as a replacement for the original equipment pump on select Volkswagen applications. Part number 904-835 is built to restore vacuum supply for engine and vehicle systems that rely on mechanically driven vacuum operation. The aluminum housing and integrated relief valve support dependable service, while the gear-drive layout and barbed inlet connection match the listed OE-style configuration. This part cross-references Volkswagen 06L145100F for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply from a worn or failing pump\u003c\/li\u003e\n\u003cli\u003eVacuum-related drivability or control issues tied to pump performance\u003c\/li\u003e\n\u003cli\u003eReduced operation of vacuum-operated vehicle functions\u003c\/li\u003e\n\u003cli\u003eLeaks or poor sealing caused by pump wear\u003c\/li\u003e\n\u003cli\u003eReplacement needs on mechanically driven Volkswagen vacuum pump applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm the inlet size, connector style, and mounting configuration against the original unit on the vehicle. This pump does not include pulley, mounting hardware, or gasket\/seal, so reuse or source the required related components as needed for the repair. Part number 904-835 is listed for 2012-2018 Volkswagen Beetle and 2014-2015 Volkswagen Golf applications with mechanically driven vacuum pump setups.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this replacement pump to match OE fit and function using durable materials for reliable service. The design supports consistent operation in the vacuum system on the specified Volkswagen applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327441531061,"sku":"BKKY-904-835","price":269.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904835_Fro.jpg?v=1775011878"},{"product_id":"dorman-904-837-vacuum-pump","title":"Dorman 904-837 Vacuum Pump","description":"\u003ch2\u003eBMW Vacuum Pump Replacement\u003c\/h2\u003e\u003cp\u003eDorman 904-837 is a mechanically driven vacuum pump replacement for select BMW applications. It matches the original equipment fit and function, with durable aluminum construction and the key operating features needed to support vacuum-operated vehicle systems.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eCompatible with select BMW 1 Series M, 135i, 325i, 335i, 335is, 335xi, 335i xDrive, 535i, 535i xDrive, 535xi, 740i, 740Li, X6, and Z4 applications\u003c\/li\u003e\n\u003cli\u003eBelt-driven vacuum pump design for mechanically driven systems\u003c\/li\u003e\n\u003cli\u003eAluminum housing for dependable service\u003c\/li\u003e\n\u003cli\u003eIncludes pulley and gasket or seal\u003c\/li\u003e\n\u003cli\u003eBarbed connector with 0.577 in inlet and inside diameter\u003c\/li\u003e\n\u003cli\u003eRelief valve included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cp\u003eFits 2009-2016 BMW Z4, mechanically driven vacuum pump. Fits 2011-2013 BMW 325i, mechanically driven vacuum pump. Fits 2011-2013 BMW 335is, mechanically driven vacuum pump. Fits 2012 BMW 335i, mechanically driven vacuum pump. Fits 2007-2010 BMW 335i, mechanically driven vacuum pump. Fits 2011-2012 BMW 740i, mechanically driven vacuum pump. Fits 2011-2012 BMW 740Li, mechanically driven vacuum pump. Fits 2011 BMW 1 Series M, mechanically driven vacuum pump. Fits 2008-2010 BMW 135i, mechanically driven vacuum pump. Fits 2009-2010 BMW 335i xDrive, mechanically driven vacuum pump. Fits 2008-2010 BMW 535i, mechanically driven vacuum pump. Fits 2009-2010 BMW 535i xDrive, mechanically driven vacuum pump. Fits 2008-2010 BMW X6, mechanically driven vacuum pump. Fits 2007-2008 BMW 335xi, mechanically driven vacuum pump. Fits 2008 BMW 535xi, mechanically driven vacuum pump.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Restore\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow vacuum supply to brake or engine vacuum circuits\u003c\/li\u003e\n\u003cli\u003eVacuum-related warning lights or drivability concerns tied to pump wear\u003c\/li\u003e\n\u003cli\u003eLoss of consistent vacuum-operated function on mechanically driven BMW systems\u003c\/li\u003e\n\u003cli\u003eNoise or leakage from a worn pump housing or seal\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the belt-drive configuration, connector style, and 0.577 in inlet before installation. This pump includes a gasket or seal, but mounting hardware is not included. Confirm the original pump layout and vacuum line routing on the vehicle before replacement. This part cross-references BMW 11667519458 for the same application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman 904-837 is built as a direct replacement for the original equipment pump, using durable materials and an aluminum housing for reliable operation in vacuum-operated vehicle functions.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327442481333,"sku":"BKKY-904-837","price":451.88,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904837_Fro.jpg?v=1775011879"},{"product_id":"dorman-904-838-vacuum-pump","title":"Dorman 904-838 Vacuum Pump","description":"\u003ch2\u003eOE-Style Vacuum Pump Replacement\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump is built to match the fit and function of the original equipment unit on select Audi and Volkswagen applications. It supports vacuum-operated vehicle functions with a durable aluminum housing and a gear-drive design for dependable service.\u003c\/p\u003e\u003cp\u003eUse Dorman 904-838 when you need a direct replacement vacuum pump for vehicles such as the Audi Q3, Audi Q3 Quattro, Volkswagen Tiguan, Volkswagen Tiguan Limited, Volkswagen GTI, and Volkswagen Beetle.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement vacuum pump for vacuum system service\u003c\/li\u003e\n\u003cli\u003eAluminum housing for durable construction\u003c\/li\u003e\n\u003cli\u003eGear-drive vacuum pump design\u003c\/li\u003e\n\u003cli\u003eBarbed connector and 0.346 in inlet for the specified application\u003c\/li\u003e\n\u003cli\u003eRelief valve included for system protection\u003c\/li\u003e\n\u003cli\u003ePackage contents include 1 pump assembly and 1 gasket\u003c\/li\u003e\n\u003cli\u003eCross-references Volkswagen 06J145100F for the same application\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eDorman 904-838 is a mechanically driven vacuum pump engineered to match the original equipment pump’s fit and function. It is built for vacuum-operated vehicle functions and uses an aluminum housing, a barbed connector, and a gear-drive system to support reliable operation in the emission control vacuum system. This replacement is a practical choice for Audi Q3 and Q3 Quattro models, as well as Volkswagen Tiguan, Tiguan Limited, GTI, and Beetle applications listed below.\u003c\/p\u003e\u003cp\u003eFits 2015-2018 Audi Q3, N\/A. Fits 2015-2018 Audi Q3 Quattro, N\/A. Fits 2017-2018 Volkswagen Tiguan Limited, N\/A. Fits 2009-2017 Volkswagen Tiguan, N\/A. Fits 2012-2014 Volkswagen GTI, N\/A, mechanically driven vacuum pump. Fits 2012-2013 Volkswagen Beetle, N\/A.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Resolve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow or inconsistent vacuum supply to engine-driven systems\u003c\/li\u003e\n\u003cli\u003eVacuum-related warning lights or drivability concerns\u003c\/li\u003e\n\u003cli\u003eLoss of vacuum support for vehicle functions that rely on pump output\u003c\/li\u003e\n\u003cli\u003eFailure of the original mechanically driven vacuum pump\u003c\/li\u003e\n\u003cli\u003eVacuum leaks at the pump connection or housing area\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s engine configuration and match the inlet size, barbed connector style, and gear-drive layout before installation. This pump is supplied without pulley, mounting hardware, or a separate seal, and the package includes a gasket. Always inspect the mounting surface and vacuum lines for wear or damage during replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman builds this replacement pump to match original equipment fit and function using durable materials for reliable service. It is engineered as a direct replacement for the specified Audi and Volkswagen applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327442874549,"sku":"BKKY-904-838","price":499.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904838_Fro.jpg?v=1775011879"},{"product_id":"dorman-904-848-vacuum-pump","title":"Dorman 904-848 Vacuum Pump","description":"\u003ch2\u003eDorman 904-848 Vacuum Pump for Sprinter\u003c\/h2\u003e\u003cp\u003eDorman 904-848 is a mechanically driven vacuum pump built to match the fit and function of the original equipment unit. It is made with durable aluminum housing and includes a gasket for a direct replacement on select Dodge Sprinter 2500 and Sprinter 3500 models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eOE-style replacement vacuum pump for vacuum-operated vehicle functions\u003c\/li\u003e\n\u003cli\u003eAluminum housing for dependable service\u003c\/li\u003e\n\u003cli\u003eBelt-drive design with barbed connector\u003c\/li\u003e\n\u003cli\u003eRelief valve included\u003c\/li\u003e\n\u003cli\u003eGasket included for installation sealing\u003c\/li\u003e\n\u003cli\u003eFits 2003 Dodge Sprinter 2500, mechanically driven vacuum pump\u003c\/li\u003e\n\u003cli\u003eFits 2003 Dodge Sprinter 3500, mechanically driven vacuum pump\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Dorman vacuum pump, part number 904-848, is engineered as a direct-fit replacement for the original equipment pump used on 2003 Dodge Sprinter 2500 and 2003 Dodge Sprinter 3500 models with a mechanically driven vacuum pump. The belt-drive configuration, 0.311 in inlet, and barbed connector support proper routing and connection in the vacuum system. Built with an aluminum housing and a relief valve, this replacement helps restore consistent vacuum supply for vehicle systems that depend on engine-driven vacuum.\u003c\/p\u003e\u003cp\u003eThis part cross-references OE numbers 5117674AA and 6112300265 for the same application. The Dorman 904-848 vacuum pump is a practical choice when servicing a Sprinter vacuum system and replacing a worn or failing pump with a unit that matches the original fit and function.\u003c\/p\u003e\u003ch2\u003eWhat This Part Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of vacuum supply to engine-driven accessories or controls\u003c\/li\u003e\n\u003cli\u003eVacuum pump noise or inconsistent operation\u003c\/li\u003e\n\u003cli\u003eVacuum leaks at the pump connection or sealing surface\u003c\/li\u003e\n\u003cli\u003eReduced performance from a worn mechanically driven pump\u003c\/li\u003e\n\u003cli\u003eService needs on 2003 Dodge Sprinter 2500 and Sprinter 3500 vacuum systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses a mechanically driven vacuum pump before ordering. Confirm the inlet size, barbed connector style, and belt-drive layout match the original unit on the vehicle. Inspect the mounting surface and vacuum lines before installation, and use the included gasket to help ensure a proper seal. Mounting hardware and pulley are not included.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eDorman manufactures this replacement pump to match original equipment fit and function using durable materials for reliable service. It is built for dependable operation in vacuum-operated vehicle functions on the specified Sprinter applications.\u003c\/p\u003e","brand":"Dorman","offers":[{"title":"Default Title","offer_id":44327444283573,"sku":"BKKY-904-848","price":440.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/RB_904848_Fro.jpg?v=1775011880"}],"url":"https:\/\/www.partcatalog.com\/collections\/vacuum-system-1.oembed?page=7","provider":"PartCatalog","version":"1.0","type":"link"}