{"title":"Valeo","description":"","products":[{"product_id":"valeo-v2069-clutch-flywheel","title":"Valeo V2069 Clutch Flywheel","description":"\u003ch2\u003eValeo V2069 Flywheel for Jeep Applications\u003c\/h2\u003e\u003cp\u003eThe Valeo V2069 is a steel single mass clutch flywheel built for Jeep manual transmission applications. It mounts to the crankshaft and helps transfer engine power while smoothing speed fluctuations caused by torque changes.\u003c\/p\u003e\u003cp\u003eFor Jeep Grand Cherokee, Cherokee, Wrangler, TJ, and Comanche models, this flywheel supports consistent clutch engagement and dependable drivetrain operation. The Valeo Flywheel line focuses on OE-style replacement parts for transmission service, and V2069 is a direct-fit option for the listed applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSteel core material for strength and durability\u003c\/li\u003e\n\u003cli\u003eSingle mass flywheel construction\u003c\/li\u003e\n\u003cli\u003eTransfers engine power to the transmission\u003c\/li\u003e\n\u003cli\u003eHelps reduce shaft speed variation from torque fluctuations\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for manual transmission service\u003c\/li\u003e\n\u003cli\u003eFits Jeep Grand Cherokee, Cherokee, Wrangler, TJ, and Comanche applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo V2069 is a clutch flywheel engineered as a single mass design for Jeep manual transmission setups. By attaching to the crankshaft, it provides the rotating mass needed for starting and power transfer while helping stabilize engine speed changes during operation. This makes it a practical replacement for worn or damaged flywheels on Jeep Grand Cherokee and Jeep Wrangler platforms, as well as Cherokee, TJ, and Comanche models.\u003c\/p\u003e\u003cp\u003eThis part cross-references LuK LFW193 for the same application. The Valeo V2069 part number is also useful when searching for a direct replacement flywheel for Jeep transmission repair.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eClutch chatter during engagement\u003c\/li\u003e\n\u003cli\u003eVibration from a worn flywheel surface\u003c\/li\u003e\n\u003cli\u003eUneven power transfer between engine and transmission\u003c\/li\u003e\n\u003cli\u003eStarting or drivability issues related to flywheel wear\u003c\/li\u003e\n\u003cli\u003eNoise caused by damaged or heat-spotted flywheel material\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s year, model, and manual transmission setup before installation. Inspect the clutch assembly, rear main seal area, and crankshaft mounting surface during service, and confirm the replacement flywheel matches the original application for Jeep Grand Cherokee, Cherokee, Wrangler, TJ, or Comanche. Follow factory torque specifications and service procedures during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-style drivetrain components, and this flywheel uses steel construction for dependable service in the listed Jeep applications. Part number V2069 is built for direct replacement use in transmission repair work.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268287422645,"sku":"BCRR-V2069","price":253.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_V2069_Fro.jpg?v=1775139766"},{"product_id":"valeo-v2127sb-clutch-flywheel","title":"Valeo V2127SB Clutch Flywheel","description":"\u003ch2\u003eValeo V2127SB Flywheel Overview\u003c\/h2\u003e\u003cp\u003eThe Valeo V2127SB is a single mass flywheel for transmission service on select Ford truck applications. It transfers engine power to the transmission while helping smooth rotational speed changes caused by torque fluctuations. Compatible with 1988-1994 Ford F-250 and 1988-1994 Ford F-350 applications, this flywheel supports direct replacement needs for common heavy-duty drivetrain repairs.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eSingle mass flywheel construction\u003c\/li\u003e\n\u003cli\u003eMounts to the crankshaft for engine-to-transmission power transfer\u003c\/li\u003e\n\u003cli\u003eHelps neutralize shaft speed variation from torque changes\u003c\/li\u003e\n\u003cli\u003eOE-style replacement for transmission service work\u003c\/li\u003e\n\u003cli\u003ePart number V2127SB for ordering and cross-reference\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo Flywheel V2127SB is built for Ford truck drivetrain applications where a conventional single mass flywheel is required. As part of the Flywheel product line, it serves the core function of linking the engine and transmission while maintaining rotational consistency during operation. This makes it a practical replacement for 1988-1994 Ford F-250 and 1988-1994 Ford F-350 models that need flywheel service during clutch or transmission repair.\u003c\/p\u003e\u003cp\u003eThis part cross-references LuK LFW127 and Sachs NFW1069 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Flywheel Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eEngine-to-transmission power transfer issues caused by a worn flywheel\u003c\/li\u003e\n\u003cli\u003eShudder or vibration related to uneven rotational speed\u003c\/li\u003e\n\u003cli\u003eClutch engagement problems tied to flywheel surface wear\u003c\/li\u003e\n\u003cli\u003eNoise or drivability concerns during drivetrain service\u003c\/li\u003e\n\u003cli\u003eReplacement needs during transmission or clutch repair on Ford F-250 and Ford F-350 trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eInspect the clutch system, crankshaft mounting surface, and related drivetrain components before installation. Confirm the application by year and model: Fits 1988-1994 Ford F-250, N\/A; Fits 1988-1994 Ford F-350, N\/A. Follow factory service procedures and torque specifications during installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo manufactures drivetrain components for service applications, and this flywheel is identified by part number V2127SB for accurate catalog matching and fitment verification.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268289388725,"sku":"BCRR-V2127SB","price":380.77,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_V2127SB_Fro.jpg?v=1775139766"},{"product_id":"valeo-10000415-a-c-compressor","title":"Valeo 10000415 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Corolla\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is a direct replacement for select 1998-2002 Toyota Corolla models with no speed sensor. Built to OEM standard, it uses high-quality components to support reliable cooling performance, lower noise, and efficient operation. Part number 10000415 is a fit-focused solution for restoring cabin comfort in your Toyota Corolla.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line A\/C compressor, part number 10000415\u003c\/li\u003e\n\u003cli\u003eOEM standard replacement for HVAC A\/C clutch and compressor service\u003c\/li\u003e\n\u003cli\u003eDesigned for R134a refrigerant systems\u003c\/li\u003e\n\u003cli\u003eUses PAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003e10PA compressor type with 6-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core construction with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings listed for installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo Compressors are built with quality components to deliver dependable operation and consistent performance in everyday driving. This compressor is a direct replacement for the original unit used on select Toyota Corolla applications, helping maintain proper A\/C system function while supporting reduced noise and efficient belt-driven operation. The Valeo Compressor line is positioned as an OEM-standard replacement solution, and part number 10000415 is engineered for vehicles using R134a refrigerant and PAG 46 oil.\u003c\/p\u003e\u003cp\u003eThis part cross-references Four Seasons 78320 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat This Compressor Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy or worn compressor operation\u003c\/li\u003e\n\u003cli\u003eA\/C system performance loss from compressor failure\u003c\/li\u003e\n\u003cli\u003eRestoration of factory-style refrigerant system operation\u003c\/li\u003e\n\u003cli\u003eReplacement needs on 1998-2002 Toyota Corolla, compressor applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 1998-2002 Toyota Corolla, compressor, w\/o speed sensor. Confirm the vehicle uses R134a refrigerant and PAG 46 oil before installation. Replace the listed gaskets and O-rings during service, and follow the included installation instructions for proper compressor setup and system evacuation procedures. Verify belt routing for the 6-groove serpentine drive and inspect the A\/C system for contamination before installing part number 10000415.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OEM-standard compressor components and designs this unit for direct replacement use in the specified Toyota Corolla applications. The compressor is built to match the original system requirements for fit and function.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268289421493,"sku":"BCRR-10000415","price":309.46,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000415_Fro.jpg?v=1775139767"},{"product_id":"valeo-10000437-a-c-compressor","title":"Valeo 10000437 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for GM Applications\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo V5 A\/C compressor, part number 10000437. Built with OEM-standard construction, it is a direct replacement compressor for select Buick, Chevrolet, Oldsmobile, and Pontiac vehicles that use R134a refrigerant and PAG 46 oil.\u003c\/p\u003e\u003cp\u003eValeo Compressor line components are engineered for reliable operation, controlled noise, and efficient performance. This compressor is designed for drivers who need a replacement that matches original equipment requirements on vehicles such as the Buick Century, Chevrolet Impala, and Pontiac Grand Prix.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo A\/C compressor, part number 10000437\u003c\/li\u003e\n\u003cli\u003eV5 compressor design with aluminum core material\u003c\/li\u003e\n\u003cli\u003eUses R134a refrigerant and PAG 46 compatible oil\u003c\/li\u003e\n\u003cli\u003eClutch included for a more complete replacement\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive with 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eOEM standard grade for direct-fit service work\u003c\/li\u003e\n\u003cli\u003eOil included; fluid capacity listed at 200 mL\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for sealing points\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis Valeo compressor is built for HVAC systems that require a V5-style A\/C compressor with a serpentine belt drive and 6-groove pulley. It is silver in color, uses aluminum core construction, and is specified for R134a refrigerant with PAG 46 oil. The included clutch and oil support replacement service on vehicles that need an OEM-standard compressor assembly. This part number 10000437 also cross-references Delphi CS0051 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With select 1996-2005 Buick Century, 1996 Buick Regal, 2000-2003 Chevrolet Impala, 1996-2003 Chevrolet Monte Carlo, 1996-2001 Chevrolet Lumina, 1996-2000 Oldsmobile Silhouette, 1996-1997 Oldsmobile Cutlass Supreme, 1999-2000 Pontiac Montana, 1996-1998 Pontiac Trans Sport, and 1996-2003 Pontiac Grand Prix applications. For shoppers searching for a Buick Century A\/C compressor, Chevrolet Impala compressor replacement, or Pontiac Grand Prix HVAC compressor, this Valeo unit matches the listed fitment.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of cabin cooling from a worn or failed compressor\u003c\/li\u003e\n\u003cli\u003eNoise from the A\/C compressor clutch or internal compressor wear\u003c\/li\u003e\n\u003cli\u003eReduced refrigerant circulation in the HVAC system\u003c\/li\u003e\n\u003cli\u003eLeaks at compressor sealing surfaces that require new gaskets or O-rings\u003c\/li\u003e\n\u003cli\u003eCompressor replacement needs on R134a-equipped GM vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and belt routing before installation. Flush the system as needed, replace the receiver\/drier or accumulator when required by service procedure, and evacuate and recharge the system to the correct specification after installation. Follow the included instructions and use the listed gaskets and O-rings to help ensure proper sealing.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components to major vehicle manufacturers worldwide, and this compressor is built to OEM standard requirements for fit and function in the listed applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268289945781,"sku":"BCRR-10000437","price":311.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000437_Fro.jpg?v=1775139767"},{"product_id":"valeo-10000443-a-c-compressor","title":"Valeo 10000443 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for GM Full-Size Sedans\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo V5 A\/C compressor, part number 10000443. Built with an aluminum core, OEM-standard grade, and a direct-replacement design, it is made for reliable operation, lower noise, and efficient performance in the HVAC system.\u003c\/p\u003e\u003cp\u003eCompatible with R134a refrigerant and PAG 46 oil, this compressor includes the clutch and comes with installation instructions and gaskets\/O-rings. It is a direct-fit option for select Buick, Pontiac, and Oldsmobile applications, including Buick Park Avenue and Pontiac Bonneville models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line direct replacement A\/C compressor\u003c\/li\u003e\n\u003cli\u003ePart number 10000443 for accurate ordering and service matching\u003c\/li\u003e\n\u003cli\u003eV5 compressor type with 6-groove serpentine belt drive\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant and PAG 46 oil specification\u003c\/li\u003e\n\u003cli\u003eAluminum core construction with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included for a complete compressor assembly\u003c\/li\u003e\n\u003cli\u003eOil included, with 200 mL fluid capacity\u003c\/li\u003e\n\u003cli\u003eOEM-standard grade for service replacement use\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included for sealing during installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressors are built with quality components to support dependable A\/C performance and consistent cabin comfort. The Compressor product line focuses on direct replacement fitment and OE-style construction, making this unit a practical choice for service work on vehicles that use the V5 compressor design. Part number 10000443 is engineered for applications that require R134a refrigerant, PAG 46 oil, and a serpentine belt drive.\u003c\/p\u003e\u003cp\u003eThis compressor cross-references Four Seasons 58994 for the same application. It is a fitment match for 1997-2005 Buick Park Avenue, 1997-2005 Pontiac Bonneville, 1997-1999 Buick LeSabre, 1997-1999 Buick Riviera, 1998-1999 Oldsmobile 88, 1997-1999 Oldsmobile LSS, and 1997-1998 Oldsmobile Regency. If you are servicing a Buick Park Avenue or Pontiac Bonneville A\/C system, 10000443 provides the correct compressor configuration for these listed vehicles.\u003c\/p\u003e\u003ch2\u003eWhat This Compressor Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or no cold air from the HVAC system\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation or belt-driven compressor noise\u003c\/li\u003e\n\u003cli\u003eRefrigerant circulation problems in the A\/C system\u003c\/li\u003e\n\u003cli\u003eCompressor failure on R134a-equipped vehicles\u003c\/li\u003e\n\u003cli\u003eService replacement needs for OE-style A\/C repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle’s refrigerant type, oil specification, and compressor style before installation. This unit uses PAG 46 oil and a 6-groove serpentine belt setup, so the existing system should match those requirements. Replace the included sealing components during installation, follow the supplied instructions, and evacuate and recharge the system according to service specifications after the compressor is installed.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components to major vehicle manufacturers worldwide, and this compressor is built to OEM-standard expectations for direct replacement service. The design emphasizes reliable operation, reduced noise, and efficient performance for the listed Buick, Pontiac, and Oldsmobile applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268290175157,"sku":"BCRR-10000443","price":305.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000443_Fro.jpg?v=1775139767"},{"product_id":"valeo-10000501-a-c-compressor","title":"Valeo 10000501 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Ford and Mercury\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is built as a direct replacement for select Ford and Mercury applications, including the 2003-2004 Ford Focus, 1996-2000 Ford Taurus, and 1996-2000 Mercury Sable. Part number 10000501 is an OEM-standard compressor designed for R134a systems and everyday drivability.\u003c\/p\u003e\u003cp\u003eValeo Compressor products are engineered with quality components to support reliable operation, lower noise, and efficient performance. This compressor uses an FS10 design with a silver aluminum core, a 6-groove serpentine pulley, and an included clutch for a straightforward replacement on the listed vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo Compressor\u003c\/li\u003e\n\u003cli\u003ePart Number: 10000501\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for direct replacement service\u003c\/li\u003e\n\u003cli\u003eFS10 compressor design\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003ePAG 46 compatible refrigerant oil type\u003c\/li\u003e\n\u003cli\u003eSilver aluminum core material\u003c\/li\u003e\n\u003cli\u003e6-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo 10000501 is a replacement A\/C compressor for Ford Focus, Ford Taurus, and Mercury Sable models listed in the fitment data. It is built to match the original system requirements for R134a refrigerant and PAG 46 oil, helping maintain proper air conditioning operation in vehicles that use an FS10 compressor layout. This part cross-references Four Seasons 57146 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Compressor Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the A\/C system\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement issues\u003c\/li\u003e\n\u003cli\u003eExcessive compressor noise during operation\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant system pressure from compressor wear\u003c\/li\u003e\n\u003cli\u003ePoor A\/C performance in Ford Focus, Ford Taurus, or Mercury Sable applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses an FS10 compressor with a 6-groove serpentine belt setup before installation. Flush the system as needed, replace the receiver\/drier or accumulator when required by service procedure, and use the correct PAG 46 oil amount for the system. Confirm all gaskets and O-rings are seated properly, then evacuate and recharge the system with R134a to factory specifications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies compressors built with OEM-standard construction and direct-replacement fitment for the listed Ford and Mercury vehicles. The design focuses on reliable operation, reduced noise, and consistent performance in everyday HVAC service.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268291649717,"sku":"BCRR-10000501","price":279.29,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000501_Fro.jpg?v=1775139767"},{"product_id":"valeo-10000519-a-c-compressor","title":"Valeo 10000519 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Ford and Lincoln Applications\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000519 A\/C compressor is an OEM-standard replacement built for vehicles that use R134a refrigerant and PAG 46 oil. It is designed for direct replacement service on select Ford, Lincoln, and Mercury models with a 6-groove serpentine belt drive.\u003c\/p\u003e\u003cp\u003eValeo Compressor products are built with high-quality components for dependable operation, quieter performance, and reduced engine load. This compressor includes the clutch and uses an aluminum core for a service-ready fit on many Ford F-150, Mustang, Escape, and E-Series applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePart number: 10000519\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade A\/C compressor\u003c\/li\u003e\n\u003cli\u003eFS10 compressor type\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant system\u003c\/li\u003e\n\u003cli\u003ePAG 46 compatible refrigerant oil type\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003e6-groove serpentine belt drive\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo 10000519 is a direct replacement A\/C compressor for select Ford, Lincoln, and Mercury vehicles. It is engineered for systems that require an FS10 compressor with a 6-groove pulley, making it a strong match for common truck, van, SUV, and car HVAC repairs. This part number 10000519 is listed for applications such as the Ford F-150, Ford Escape, Ford Mustang, Lincoln Navigator, and Mercury Mariner.\u003c\/p\u003e\u003cp\u003eThis part cross-references Dorman - HELP (e.g., 58129, 58165) for the same application. It also cross-references Global Parts Distributors LLC (e.g., 6511447, 6511480) for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2005-2007 Ford E-150, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005-2007 Ford E-250, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005-2007 Ford E-350 Super Duty, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2001 Ford E-350 Super Duty, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Ford Escape, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2004 Ford Escape, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2007 Ford F-250 Super Duty, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2007 Ford F-350 Super Duty, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006-2007 Mercury Mariner, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006 Ford F-150, N\/A, To 12\/05\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006 Ford F-150, N\/A, From 12\/05\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1996-2006 Ford Mustang, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006 Lincoln Mark LT, N\/A, To 12\/05\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2006 Lincoln Mark LT, N\/A, From 12\/05\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005 Ford E-150 Club Wagon, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005 Ford E-350 Club Wagon, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005 Ford Escape, N\/A, To 05\/02\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2005 Ford Excursion, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2005 Ford F-150, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2005 Mercury Mariner, N\/A, To 05\/02\/05; w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2004 Ford F-150 Heritage, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1991-2004 Ford Grand Marquis, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Lincoln Blackwood, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1992-2002 Ford Crown Victoria, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2002 Ford E-150 Econoline, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2002 Ford E-150 Econoline Club Wagon, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2002 Ford E-250 Econoline, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2002 Ford E-350 Econoline Club Wagon, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-2002 Ford Expedition, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1998-2002 Lincoln Navigator, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1991-2002 Lincoln Town Car, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1992-2002 Mercury Grand Marquis, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2001 Ford Econoline, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-1999 Ford F-250, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1997-1998 Ford E-350 Econoline, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1993-1998 Lincoln Mark VIII, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-1997 Ford Thunderbird, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-1997 Mercury Cougar, N\/A, w\/ 6 Grooves; Compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm the vehicle uses R134a refrigerant and PAG 46 oil before installation.\u003c\/li\u003e\n\u003cli\u003eVerify the compressor type is FS10 and the pulley has 6 grooves.\u003c\/li\u003e\n\u003cli\u003eReplace the included gaskets and O-rings during installation.\u003c\/li\u003e\n\u003cli\u003eFollow the supplied installation instructions and evacuate the system before recharging.\u003c\/li\u003e\n\u003cli\u003eCheck belt alignment and system cleanliness to protect the replacement compressor.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-standard HVAC components used in direct replacement service, with the same product family supplied to major vehicle manufacturers worldwide. The 10000519 compressor is built for reliability, consistent performance, and reduced noise in everyday driving conditions.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268291813557,"sku":"BCRR-10000519","price":272.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000519_Fro.jpg?v=1775139768"},{"product_id":"valeo-10000522-a-c-compressor","title":"Valeo 10000522 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Ford and Mazda\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000522 A\/C compressor is an OEM-standard replacement built for reliable cabin cooling and consistent system performance. It uses an FS10 design with a silver aluminum core, a 6-groove serpentine pulley, and a clutch included for a direct-fit service replacement.\u003c\/p\u003e\u003cp\u003eDesigned for R134a systems with PAG 46 oil specification, this compressor is a practical choice for Ford Ranger, Ford Explorer, Mazda B3000, and related applications that need a factory-style HVAC compressor. Valeo Compressor products are built to match the quality level used by major vehicle manufacturers worldwide.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo Compressor\u003c\/li\u003e\n\u003cli\u003ePart number: 10000522\u003c\/li\u003e\n\u003cli\u003eFS10 A\/C compressor design\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003ePAG 46 compatible refrigerant oil type\u003c\/li\u003e\n\u003cli\u003e6-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo 10000522 is a direct replacement A\/C compressor engineered for vehicles that require an FS10 compressor configuration. It is built to restore refrigerant circulation in the HVAC system while maintaining the fit, function, and service characteristics expected in OE-style repairs. This part cross-references UAC CO102580AC for the same application.\u003c\/p\u003e\u003cp\u003eCompatible With Ford Ranger, Ford Explorer, Ford Explorer Sport Trac, Ford Explorer Sport, Ford F-100 Ranger, Ford E-350 Club Wagon, Ford E-350 Super Duty, Mazda B4000, Mazda B3000, Mazda Navajo, and Mercury Mountaineer applications listed in the fitment data. The Valeo 10000522 compressor is also a strong match for long-tail searches such as Ford Ranger A\/C compressor replacement, Ford Explorer scroll style compressor, and Mazda B3000 HVAC compressor replacement.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of cabin cooling from a worn or seized compressor\u003c\/li\u003e\n\u003cli\u003eNoise from the A\/C compressor clutch or internal compressor wear\u003c\/li\u003e\n\u003cli\u003eWeak refrigerant circulation in an R134a system\u003c\/li\u003e\n\u003cli\u003eCompressor failure on FS10-equipped Ford and Mazda vehicles\u003c\/li\u003e\n\u003cli\u003eHVAC performance issues tied to belt-driven compressor operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses an FS10 compressor and a 6-groove serpentine belt setup before installation. Confirm refrigerant type and oil specification match the system requirements: R134a with PAG 46. Replace the included gaskets \/ O-rings during installation, follow the supplied instructions, and evacuate and recharge the system according to service procedures. For 2003 Ford E-350 Club Wagon and 2003 Ford E-350 Super Duty applications, note the fitment requirement from 08\/09\/02.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo designs this compressor as an OEM-standard replacement using high-quality components for dependable operation and reduced noise. The product line is built to support consistent performance and direct-fit service on the listed Ford Ranger, Ford Explorer, and Mazda applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268292141237,"sku":"BCRR-10000522","price":271.62,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000522_Fro.jpg?v=1775139768"},{"product_id":"valeo-10000532-a-c-compressor","title":"Valeo 10000532 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Ford and Mercury\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo A\/C compressor, part number 10000532. It is built as an OEM-standard direct replacement for select Ford, Lincoln, and Mercury vehicles, with a design focused on reliable operation, lower noise, and efficient performance.\u003c\/p\u003e\u003cp\u003eCompatible with 2004 Ford Explorer, 2002 Ford Explorer, 2004 Mercury Mountaineer, 2002 Mercury Mountaineer, and other listed Ford E-Series, Expedition, Excursion, F-150, Crown Victoria, Town Car, Grand Marquis, Marauder, and Navigator applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor product line for OE-style replacement applications\u003c\/li\u003e\n\u003cli\u003eFS10 compressor type with clutch included\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant and PAG 46 oil specification\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive with 8-groove pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for direct-fit service replacement\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo designs this compressor with quality components to support dependable A\/C system operation and consistent cooling performance. The compressor is intended for vehicles using R134a refrigerant and PAG 46 oil, and it includes the clutch for a more complete service replacement. As part of the Valeo Compressor line, this unit reflects the same type of OE-focused engineering supplied to major vehicle manufacturers worldwide.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 210159) for the same application.\u003c\/p\u003e\u003ch2\u003eCommon A\/C Problems It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement issues\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C performance from worn internal components\u003c\/li\u003e\n\u003cli\u003eService replacement for a failed FS10 compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and compressor style before installation. This unit uses PAG 46 oil and R134a refrigerant, and the included instructions can help guide the replacement process. Always inspect the system for contamination, replace worn seals as needed, and evacuate and recharge the system according to factory procedures.\u003c\/p\u003e\u003cp\u003eFits 2002-2004 Ford Excursion, compressor; 2002-2004 Ford Explorer, compressor; 1997-2002 Ford E-150 Econoline, compressor; 1997-2002 Ford E-150 Econoline Club Wagon, compressor; 2002 Ford E-150, pulley diameter 4.5in; compressor; 2003 Ford E-150, to 08\/09\/02; compressor; 2003 Ford E-150 Club Wagon, to 08\/09\/02; compressor; 1997-2002 Ford E-250 Econoline, compressor; 1997-2002 Ford E-350 Econoline Club Wagon, compressor; 1997-1998 Ford E-350 Econoline, compressor; 1999-2002 Ford E-350 Econoline, pulley diameter 4.5in; compressor; 2002 Ford E-350 Club Wagon, pulley diameter 4.5in; compressor; 1999-2002 Ford E-350 Super Duty, compressor; 2003 Ford E-350 Club Wagon, to 08\/09\/02; compressor; 2003 Ford E-350 Super Duty, to 08\/09\/02; compressor; 1999-2002 Ford Econoline, pulley diameter 4.5in; compressor; 1997-2002 Ford Expedition, compressor; 2000-2001 Ford Excursion, compressor; 2002 Ford F-150, pulley diameter 4.5in; compressor; 2003 Ford F-150, compressor; 2003 Ford Crown Victoria, compressor; 2003 Lincoln Town Car, compressor; 1998-2002 Lincoln Navigator, compressor; 2003 Mercury Grand Marquis, compressor; 2003 Mercury Marauder, compressor; 2002 Ford Explorer, compressor; 2004 Ford Explorer, compressor; 2002 Mercury Mountaineer, compressor; 2004 Mercury Mountaineer, compressor.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components and builds this replacement to OEM Standard specifications for the listed applications. Part number 10000532 is engineered for direct replacement service on the confirmed Ford, Lincoln, and Mercury fitments above.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268292272309,"sku":"BCRR-10000532","price":264.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000532_Fro.jpg?v=1775139768"},{"product_id":"valeo-10000540-a-c-compressor","title":"Valeo 10000540 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Ford Applications\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000540 is an OEM-standard A\/C compressor built for Ford vehicles that use an 8-groove serpentine belt and R134a refrigerant. It is a direct replacement compressor for select Ford F-250 Super Duty, F-350 Super Duty, Thunderbird, Ranger, and Econoline applications, with clutch included for a more complete service replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line engineered with high-quality components for reliable operation\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for direct replacement service\u003c\/li\u003e\n\u003cli\u003eFS10 compressor type with aluminum core material\u003c\/li\u003e\n\u003cli\u003eDesigned for R134a refrigerant and PAG 46 compressor oil\u003c\/li\u003e\n\u003cli\u003e8-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets and O-rings for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressor products are built to match the fit and function expected in original equipment service. This Valeo 10000540 A\/C compressor is silver, uses an FS10 design, and is specified for R134a systems with PAG 46 oil. It is a practical replacement choice for Ford truck and car platforms where consistent belt alignment, refrigerant compatibility, and compressor durability matter. This part cross-references UAC COYC180C for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1999-2003 Ford F-250 Super Duty, N\/A, w\/ 8 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2003 Ford F-350 Super Duty, N\/A, w\/ 8 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1989-1995 Ford Thunderbird, N\/A, w\/ 8 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1991 Ford Ranger, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985-1988 Ford Thunderbird, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985 Ford E-250 Econoline Club Wagon, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985 Ford E-350 Econoline, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985 Ford E-350 Econoline Club Wagon, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985 Ford F-250, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1985 Ford F-350, N\/A, w\/ 8 Grooves; w\/ Dealer Installed Air Conditioning; Compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eCompressor noise from worn internal components\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C performance in R134a systems\u003c\/li\u003e\n\u003cli\u003eBelt-driven compressor failure on 8-groove serpentine setups\u003c\/li\u003e\n\u003cli\u003eService replacement needs on Ford F-250 Super Duty, F-350 Super Duty, Thunderbird, Ranger, and Econoline models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses an 8-groove serpentine belt and the FS10 compressor configuration before installation. Confirm refrigerant type, oil specification, and all mounting and line connections match the original system. Installation instructions are included, and the system should be evacuated, inspected, and charged according to service procedures after compressor replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo Compressor parts are built with components selected for dependable operation and OE-standard service fit. Valeo supplies products used by major vehicle manufacturers worldwide, and this compressor is positioned as a direct replacement for the original unit.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268292370613,"sku":"BCRR-10000540","price":283.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000540_Fro.jpg?v=1775139769"},{"product_id":"valeo-10000545-a-c-compressor","title":"Valeo 10000545 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Dodge Trucks\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is an OEM-standard replacement built for reliable cabin cooling in select Dodge Dakota, Ram, Durango, and Ramcharger applications. Part number 10000545 is designed for R134a systems and uses PAG 46 oil, making it a direct-fit option for vehicles that need a compressor with a 7-groove serpentine pulley and included clutch.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line replacement for HVAC A\/C compressor service\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade with aluminum core material\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with PAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eSD7 compressor design with clutch included\u003c\/li\u003e\n\u003cli\u003e7-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eOil included and installation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets \/ O-rings for installation sealing\u003c\/li\u003e\n\u003cli\u003eSilver finish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressors are built with quality components to support dependable operation, lower noise, and efficient performance. This compressor is part of the Valeo Compressor product line, which focuses on direct replacement fitment and OE-style construction for vehicles originally equipped with this configuration. Part number 10000545 is a practical choice for Dodge Ram 1500, Ram 2500, Ram 3500, Dakota, Durango, and Ramcharger models that require the listed compressor setup.\u003c\/p\u003e\u003cp\u003eThis part cross-references Delphi CS20149 and Four Seasons 78562 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2002-2003 Dodge Dakota, N\/A, w\/ Auxiliary A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Dodge Ram 1500, N\/A, w\/ Auxiliary A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1995-2003 Dodge Ram 1500 Van, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Dodge Ram 2500, N\/A, w\/ Auxiliary A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002-2003 Dodge Ram 3500, N\/A, w\/ Auxiliary A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-2002 Dodge Ram 2500, N\/A, Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002 Dodge Ram 2500 Van, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1996 Dodge Ram 2500 Van, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-2002 Dodge Ram 3500, N\/A, Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002 Dodge Ram 3500 Van, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-2001 Dodge Dakota, N\/A, Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-2001 Dodge Ram 1500, N\/A, Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2001 Dodge Ramcharger, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1994-1996 Dodge Ramcharger, N\/A, w\/ 7 Grooves; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1998-2000 Dodge Durango, N\/A, Compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRestores weak or inconsistent air conditioning output\u003c\/li\u003e\n\u003cli\u003eAddresses compressor noise, seizure, or failure\u003c\/li\u003e\n\u003cli\u003eReplaces a leaking or inefficient A\/C compressor assembly\u003c\/li\u003e\n\u003cli\u003eHelps correct belt-drive issues on 7-groove serpentine setups\u003c\/li\u003e\n\u003cli\u003eSupports proper refrigerant circulation in R134a systems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses the listed compressor type, pulley groove count, refrigerant, and oil specification before installation. Replace sealing components as needed, follow the included instructions, and evacuate and recharge the system according to service procedures. Confirm the system is clean and free of debris before installing the new compressor to help protect the replacement unit.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components to major vehicle manufacturers worldwide, and this replacement is built to the same application-focused standard. The design emphasizes reliability, reduced noise, and efficient operation for the specified Dodge fitments.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268292468917,"sku":"BCRR-10000545","price":288.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000545_Fro.jpg?v=1775139769"},{"product_id":"valeo-10000552-a-c-compressor","title":"Valeo 10000552 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor 10000552\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000552 A\/C compressor is a direct replacement built for vehicles that use an SD7 compressor with R134a refrigerant and PAG 46 oil. It is engineered with OEM-standard components to support reliable cooling performance, lower noise, and efficient operation in daily driving.\u003c\/p\u003e\u003cp\u003eCompatible with select Volkswagen Beetle, Golf, and Jetta applications, as well as Audi TT and TT Quattro models, this compressor is a fitment-based replacement for vehicles that require the same compressor configuration. Valeo Compressor products are supplied to meet the same quality expectations used by major vehicle manufacturers.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePart number: 10000552\u003c\/li\u003e\n\u003cli\u003eBrand: Valeo Compressor\u003c\/li\u003e\n\u003cli\u003eType: SD7 A\/C compressor\u003c\/li\u003e\n\u003cli\u003eRefrigerant type: R134a\u003c\/li\u003e\n\u003cli\u003eCompatible refrigerant oil: PAG 46\u003c\/li\u003e\n\u003cli\u003eClutch included for direct replacement use\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive with 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eOil included, 145 mL fluid capacity\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressor line products are built for replacement applications where factory-style fit, function, and operating characteristics matter. The 10000552 compressor is designed for systems using R134a refrigerant and PAG 46 oil, with a clutch already included and a serpentine belt pulley setup. This makes it a practical choice for restoring A\/C performance on 1998-2001 Volkswagen Beetle, 1999 Volkswagen Golf, 1999 Volkswagen Jetta, 2000-2001 Volkswagen Golf, 2000 Audi TT, and 2000 Audi TT Quattro applications listed below.\u003c\/p\u003e\u003cp\u003eThis part cross-references Four Seasons 78541 and UAC CO1206JC for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C system pressure from compressor wear\u003c\/li\u003e\n\u003cli\u003eClutch-related compressor engagement problems\u003c\/li\u003e\n\u003cli\u003eReplacement needs after compressor seizure or internal failure\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify refrigerant type, oil type, and pulley groove count before installation.\u003c\/li\u003e\n\u003cli\u003eFlush the system if contamination or compressor failure was present.\u003c\/li\u003e\n\u003cli\u003eReplace worn seals and follow the included installation instructions.\u003c\/li\u003e\n\u003cli\u003eConfirm chassis\/VIN notes for Golf and TT applications before ordering.\u003c\/li\u003e\n\u003cli\u003eUse the correct PAG 46 oil quantity for the vehicle’s A\/C system.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo designs this compressor with high-quality components and OEM-standard construction for dependable replacement performance. The brand supplies products used by major vehicle manufacturers worldwide, and this compressor is built to match the original application requirements for the listed Volkswagen and Audi models.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268293615797,"sku":"BCRR-10000552","price":422.01,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000552_Fro.jpg?v=1775139769"},{"product_id":"valeo-10000564-a-c-compressor","title":"Valeo 10000564 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Ford and Mercury\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo A\/C compressor, part number 10000564. Built as an OEM-standard direct replacement, it is designed for reliable operation, lower noise, and efficient performance in the HVAC system.\u003c\/p\u003e\u003cp\u003eCompatible with 2001-2007 Ford Taurus, 2001-2005 Ford Ranger, and 2001-2005 Mercury Sable, this compressor supports R134a refrigerant systems and uses PAG 46 oil. The FS10 design includes a clutch, a 6-groove pulley, and a serpentine belt setup for straightforward service replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line A\/C compressor for HVAC service replacement\u003c\/li\u003e\n\u003cli\u003ePart number 10000564 for direct identification\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade with aluminum core material\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with PAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eFS10 compressor design with clutch included\u003c\/li\u003e\n\u003cli\u003e6-groove pulley for serpentine belt applications\u003c\/li\u003e\n\u003cli\u003eSilver finish with installation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets and O-rings for installation sealing\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressors are built with quality components to support dependable HVAC performance and reduced operating noise. This compressor is a direct replacement for the original unit used in Ford Taurus, Ford Ranger, and Mercury Sable applications, making it a practical choice for restoring air conditioning function without changing the system’s original refrigerant and oil requirements. The Valeo Compressor line focuses on OE-style fit and function for vehicles that need a replacement compressor matching factory specifications.\u003c\/p\u003e\u003cp\u003eThis part cross-references UAC CO101460C for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Help Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or no cabin cooling from a worn compressor\u003c\/li\u003e\n\u003cli\u003eExcessive compressor noise during A\/C operation\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant pressure caused by internal compressor wear\u003c\/li\u003e\n\u003cli\u003eClutch engagement issues affecting compressor operation\u003c\/li\u003e\n\u003cli\u003eNeed for an OE-standard replacement during HVAC repair\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses an R134a system and confirm the FS10 compressor style before installation. Replace the required gaskets and O-rings during service, and follow the included installation instructions for proper setup. Flush the system as needed and charge with PAG 46 oil only when the system specification calls for it.\u003c\/p\u003e\u003cp\u003eFits 2001-2007 Ford Taurus, compressor. Fits 2001-2005 Ford Ranger, compressor. Fits 2001-2005 Mercury Sable, compressor.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies compressors built to OEM-standard expectations and used in vehicle manufacturer applications worldwide. Part number 10000564 is engineered as a direct replacement for the original compressor in the listed Ford and Mercury models.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268293648565,"sku":"BCRR-10000564","price":288.34,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000564_Fro.jpg?v=1775139770"},{"product_id":"valeo-10000623-a-c-compressor","title":"Valeo 10000623 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Chrysler and Dodge\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is a direct replacement for select Chrysler and Dodge minivans with auxiliary A\/C. Built with OEM-standard construction, it is designed to restore refrigerant circulation, cabin cooling performance, and quiet operation in vehicles that need a reliable HVAC compressor replacement.\u003c\/p\u003e\u003cp\u003eCompatible with 2001-2007 Dodge Grand Caravan, 2001-2005 Chrysler Town \u0026amp; Country, 2003 Chrysler Voyager, and 2001 Dodge Caravan, this compressor is a fitment-focused solution for common rear-auxiliary A\/C service needs. Part number 10000623 is also referenced in OE-style replacement searches for these applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line direct replacement\u003c\/li\u003e\n\u003cli\u003ePart number: 10000623\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for factory-style fit and function\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003ePAG 46 compatible refrigerant oil type\u003c\/li\u003e\n\u003cli\u003e10S compressor design\u003c\/li\u003e\n\u003cli\u003e6-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eAluminum core material\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressors are built with quality components to support dependable HVAC performance and consistent operation. This compressor is silver, uses R134a refrigerant, and is specified for PAG 46 oil systems. The 10S design and 6-groove serpentine pulley make it a practical replacement for vehicles originally equipped with this compressor configuration. If you are searching for a Chrysler Town \u0026amp; Country A\/C compressor or a Dodge Grand Caravan compressor replacement, part number 10000623 is a direct-fit option for the listed applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Delphi CS20075 and Four Seasons 78374 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant circulation through the A\/C system\u003c\/li\u003e\n\u003cli\u003eCompressor failure on auxiliary A\/C-equipped minivans\u003c\/li\u003e\n\u003cli\u003eHVAC performance issues in Chrysler and Dodge applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, pulley groove count, and compressor style before installation. This unit is intended for R134a systems using PAG 46 oil and includes clutch hardware on the compressor assembly. Installation instructions are included, and the supplied gaskets and O-rings should be used during service. Proper evacuation, leak checking, and system recharge are required after compressor replacement.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-standard compressor components used in factory-style replacement applications worldwide. Part number 10000623 is built to match the listed fitment and compressor specifications for Chrysler and Dodge vehicles with auxiliary A\/C.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268293681333,"sku":"BCRR-10000623","price":264.1,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000623_Fro.jpg?v=1775139770"},{"product_id":"valeo-10000627-a-c-compressor","title":"Valeo 10000627 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Accord\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is built for reliable cabin cooling in 2003-2007 Honda Accord applications. It uses OEM-standard construction with an aluminum core, integrated clutch, and the correct 10S design for direct replacement service. Part number 10000627 is specified for R134a systems and is supplied with PAG 46 oil.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo Compressor line\u003c\/li\u003e\n\u003cli\u003ePart number: 10000627\u003c\/li\u003e\n\u003cli\u003eFits 2003-2007 Honda Accord, compressor\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003ePAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003e10S compressor design with 7-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eIntegrated clutch included\u003c\/li\u003e\n\u003cli\u003eAluminum core material\u003c\/li\u003e\n\u003cli\u003eOEM standard grade for direct replacement service\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo compressors are engineered with quality components to support dependable operation and consistent A\/C performance. This compressor is a direct replacement for the factory unit used on Honda Accord models from 2003 through 2007, and it matches the system requirements for R134a refrigerant and PAG 46 oil. The silver aluminum housing helps keep weight down while maintaining the durability expected in OE-style service parts. Part number 10000627 is also referenced in aftermarket catalogs for the same application, including Delphi CS20072 and Four Seasons 78389.\u003c\/p\u003e\u003cp\u003eFor drivers searching for a 2003-2007 Honda Accord A\/C compressor replacement, this Valeo unit provides the correct configuration for restoring cooling performance and reducing compressor-related noise or drivability concerns tied to a worn-out factory compressor. The Valeo Compressor line focuses on replacement parts built to the same standards used by major vehicle manufacturers worldwide.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor seizure or internal wear\u003c\/li\u003e\n\u003cli\u003eRefrigerant system pressure loss caused by compressor failure\u003c\/li\u003e\n\u003cli\u003eA\/C performance decline in Honda Accord models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and compressor style before installation. Flush the system as needed, replace worn seals, and follow the included instructions for proper setup. Use the correct PAG 46 oil amount for the system and evacuate the A\/C system before charging with R134a. This part fits 2003-2007 Honda Accord, compressor.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-standard compressor components used in factory-level applications worldwide. Part number 10000627 is built as a direct replacement to match the original system requirements for the listed Honda Accord fitment.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268293943477,"sku":"BCRR-10000627","price":329.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000627_Fro.jpg?v=1775139770"},{"product_id":"valeo-10000629-a-c-compressor","title":"Valeo 10000629 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for GM Trucks and SUVs\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is an OEM-standard replacement built for reliable cabin cooling in select Chevrolet, GMC, and Cadillac applications. Part number 10000629 is designed for vehicles using R134a refrigerant and PAG 46 oil, with a clutch included for a more complete compressor replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line, engineered as a direct replacement for factory-style service\u003c\/li\u003e\n\u003cli\u003ePart number 10000629 for accurate ordering and cross-reference\u003c\/li\u003e\n\u003cli\u003eH6 compressor type with aluminum core material and silver finish\u003c\/li\u003e\n\u003cli\u003eUses R134a refrigerant and PAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive with 4-groove pulley design\u003c\/li\u003e\n\u003cli\u003eClutch included, with oil included and installation instructions provided\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for service on original-equipment applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Compressor product line focuses on replacement compressors built with quality components for dependable operation and consistent performance. This unit is intended for GM full-size trucks, vans, and SUVs that require an H6-style A\/C compressor, including Chevrolet Silverado, Suburban, Tahoe, Avalanche, Express, and GMC Sierra, Yukon, and Savana applications. The design supports reduced noise and efficient operation while matching the original service requirements for the vehicle platform. This part cross-references Delphi CS20010 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2003-2005 Chevrolet Express 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Chevrolet Express 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2003-2005 Chevrolet Express 3500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002 Cadillac Escalade, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002 Chevrolet Avalanche 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2002 Chevrolet Avalanche 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 Chevrolet Silverado 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 Chevrolet Silverado 1500 HD, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 Chevrolet Silverado 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 Chevrolet Silverado 2500 HD, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 Chevrolet Silverado 3500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Chevrolet Suburban 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Chevrolet Suburban 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 Chevrolet Tahoe, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 GMC Sierra 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 GMC Sierra 1500 HD, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 GMC Sierra 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 GMC Sierra 2500 HD, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2001-2002 GMC Sierra 3500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 GMC Yukon, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 GMC Yukon XL 1500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2002 GMC Yukon XL 2500, w\/o Rear A\/C; Compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Problems This Compressor Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the HVAC system\u003c\/li\u003e\n\u003cli\u003eCompressor noise, seizure, or inconsistent engagement\u003c\/li\u003e\n\u003cli\u003eLow A\/C system efficiency after compressor wear\u003c\/li\u003e\n\u003cli\u003eLeak-related compressor replacement on R134a systems\u003c\/li\u003e\n\u003cli\u003eRestoring cooling performance on Chevrolet Silverado and GMC Sierra trucks\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the vehicle uses R134a refrigerant and PAG 46 oil before installation. Confirm the compressor type, pulley groove count, and belt drive configuration match the original unit. Replace the receiver\/drier or accumulator as required by the service procedure, evacuate the system, and recharge to the specified capacity after installation. This compressor includes installation instructions and gaskets\/O-rings for service preparation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo compressors are built with OEM-standard construction for direct replacement service on factory-equipped vehicles. The brand supplies products used by major vehicle manufacturers worldwide, and this compressor is designed to meet the fitment and performance expectations of those original applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268294893749,"sku":"BCRR-10000629","price":344.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000629_Fro.jpg?v=1775139771"},{"product_id":"valeo-10000631-a-c-compressor","title":"Valeo 10000631 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for GM Rear A\/C Applications\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is an OEM-standard replacement built for select Chevrolet, GMC, Cadillac, and Hummer vehicles with rear A\/C configurations. Part number 10000631 is designed for R134a systems and uses PAG 46 oil specification, making it a direct-fit option for common GM truck and SUV HVAC repairs.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line replacement A\/C compressor\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for factory-style fit and function\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with PAG 46 oil specification\u003c\/li\u003e\n\u003cli\u003e10S compressor design with 4-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eClutch included for simplified service replacement\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets \/ O-rings for installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo compressors are built with quality components to support reliable HVAC operation and consistent cabin cooling performance. The Compressor product line focuses on direct replacement fitment and OE-style construction, which is important when servicing GM vehicles such as the Chevrolet Silverado, GMC Sierra, and Cadillac Escalade. Part number 10000631 is a practical choice for technicians replacing a worn or noisy compressor in rear A\/C-equipped trucks and SUVs.\u003c\/p\u003e\u003cp\u003eThis part cross-references Delphi CS20039 for the same application.\u003c\/p\u003e\u003ch2\u003eUsed For Common A\/C Problems\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLoss of cabin cooling from a failed compressor\u003c\/li\u003e\n\u003cli\u003eNoisy or rough compressor operation\u003c\/li\u003e\n\u003cli\u003eClutch-related A\/C engagement issues\u003c\/li\u003e\n\u003cli\u003eReduced refrigerant circulation in R134a systems\u003c\/li\u003e\n\u003cli\u003eHVAC performance problems in rear A\/C GM vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and vehicle configuration before installation. This compressor is intended for systems using R134a and PAG 46, and fitment varies by rear A\/C, auxiliary A\/C, and dual-zone climate control equipment. Replace the required gaskets \/ O-rings during service and follow the included installation instructions for proper setup.\u003c\/p\u003e\u003cp\u003eCompatible with select 2003-2020 Chevrolet Express, Silverado, Suburban, Tahoe, Avalanche; GMC Savana, Sierra, Yukon; Cadillac Escalade; and 2008 Hummer H2 applications listed in the fitment data, including Chevrolet Silverado 1500, GMC Sierra 2500 HD, and Cadillac Escalade ESV rear A\/C configurations.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level components to major vehicle manufacturers worldwide, and this compressor is built to OEM Standard expectations for replacement service. Part number 10000631 is engineered as a direct replacement for the listed applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268295319733,"sku":"BCRR-10000631","price":438.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000631_Fro_f7354ffa-e628-4c1a-9eef-825b9221427f.jpg?v=1775139771"},{"product_id":"valeo-10000652-a-c-compressor","title":"Valeo 10000652 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Nissan Maxima and Murano\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000652 A\/C compressor is an OEM-standard replacement built for reliable air conditioning performance in select Nissan applications. It uses a DKS design with a silver aluminum core, a 7-groove serpentine pulley, and R134a refrigerant compatibility for direct-fit service on the vehicles listed below.\u003c\/p\u003e\u003cp\u003eValeo Compressor products are built with the same OE-focused approach used for major vehicle manufacturers worldwide. This compressor includes the clutch and installation instructions, and it is designed as a direct replacement for factory-installed HVAC compressor service.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePart number: 10000652\u003c\/li\u003e\n\u003cli\u003eBrand line: Valeo Compressor\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for OE-style replacement\u003c\/li\u003e\n\u003cli\u003eDKS compressor design\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003e7-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets \/ O-rings for installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo 10000652 is an A\/C compressor engineered for direct replacement service on 2008-2014 Nissan Maxima and 2008-2014 Nissan Murano applications listed in the fitment data. It is built to OE-standard expectations with a focus on dependable operation, reduced noise, and efficient compressor performance. If you are replacing a worn Nissan Maxima A\/C compressor or a Nissan Murano compressor for R134a systems, this Valeo unit provides a factory-style solution.\u003c\/p\u003e\u003cp\u003eThis part cross-references UAC CO11319C for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement problems\u003c\/li\u003e\n\u003cli\u003eRefrigerant circulation issues in the A\/C system\u003c\/li\u003e\n\u003cli\u003eFailure of the original factory compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify the vehicle uses an R134a refrigerant system before installation.\u003c\/li\u003e\n\u003cli\u003eConfirm pulley groove count and serpentine belt routing match the original unit.\u003c\/li\u003e\n\u003cli\u003eReplace the listed gaskets \/ O-rings during installation to help maintain a proper seal.\u003c\/li\u003e\n\u003cli\u003eFollow the included installation instructions and evacuate\/recharge the system according to service procedures.\u003c\/li\u003e\n\u003cli\u003eInspect the A\/C system for contamination or debris before installing the new compressor.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level components to major vehicle manufacturers worldwide, and this compressor is built to OEM Standard specifications for direct replacement service.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2008-2014 Nissan Maxima, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Nissan Murano, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008 Nissan Murano, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268295581877,"sku":"BCRR-10000652","price":387.19,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000652_Fro.jpg?v=1775139771"},{"product_id":"valeo-10000655-a-c-compressor","title":"Valeo 10000655 A\/C Compressor","description":"\u003ch2\u003eValeo OE A\/C Compressor for Nissan and Infiniti\u003c\/h2\u003e\u003cp\u003eThe Valeo 10000655 A\/C compressor is an OEM-standard replacement built with aluminum core construction, a silver finish, and a clutch included for service-ready installation. It is designed for R134a systems and uses a 7-groove serpentine belt drive for direct-fit HVAC repair on select Nissan and INFINITI vehicles.\u003c\/p\u003e\u003cp\u003eValeo Compressor products are part of the Valeo OE family, supplying direct replacement HVAC components that match the original equipment approach used by major vehicle manufacturers. This part number, 10000655, is built for reliable operation, controlled noise levels, and consistent air-conditioning performance in applications such as the Nissan Armada, Nissan TITAN, and INFINITI QX56.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo\u003c\/li\u003e\n\u003cli\u003ePart number: 10000655\u003c\/li\u003e\n\u003cli\u003ePart type: A\/C compressor\u003c\/li\u003e\n\u003cli\u003eRefrigerant type: R134a\u003c\/li\u003e\n\u003cli\u003eClutch included for direct replacement service\u003c\/li\u003e\n\u003cli\u003e7-groove serpentine belt drive\u003c\/li\u003e\n\u003cli\u003eAluminum core material\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings listed for installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2019-2021 Nissan NV2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Nissan NV3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2012-2018 Nissan NV2500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2014-2018 Nissan NV3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2005-2015 Nissan Armada, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2015 Nissan TITAN, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Nissan NV3500, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2008-2012 Nissan Pathfinder, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004-2010 INFINITI QX56, N\/A\u003c\/li\u003e\n\u003cli\u003eFits 2004 Nissan Pathfinder Armada, N\/A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eUse the Valeo 10000655 when replacing a worn or failed compressor in compatible Nissan and INFINITI HVAC systems. The aluminum construction, OEM-standard grade, and clutch-included design support a direct replacement approach for vehicles that use R134a refrigerant and a serpentine belt drive. If you are servicing a Nissan Armada A\/C compressor, Nissan TITAN compressor, or INFINITI QX56 compressor application, this Valeo OE unit is built to match the original system layout.\u003c\/p\u003e\u003cp\u003eThis part cross-references Four Seasons 68461 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the vents\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement issues\u003c\/li\u003e\n\u003cli\u003eUnusual A\/C compressor noise\u003c\/li\u003e\n\u003cli\u003eReduced cabin cooling performance\u003c\/li\u003e\n\u003cli\u003eSystem failure caused by compressor wear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm refrigerant type before installation; this compressor is specified for R134a systems.\u003c\/li\u003e\n\u003cli\u003eVerify pulley groove count and serpentine belt routing during replacement.\u003c\/li\u003e\n\u003cli\u003eReplace worn seals and follow the included installation instructions.\u003c\/li\u003e\n\u003cli\u003eInspect the A\/C system for contamination or debris before installing the new compressor.\u003c\/li\u003e\n\u003cli\u003eCheck system charge and operation after installation to confirm proper cooling performance.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo OE compressors are built with high-quality components and are supplied as direct replacement parts for original-equipment-style service. The 10000655 follows OEM Standard expectations and reflects Valeo’s OE supplier background for select vehicle applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268295844021,"sku":"BCRR-10000655","price":425.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000655_Fro_5914a6fa-bf04-445d-8627-5138c0253c85.jpg?v=1775139772"},{"product_id":"valeo-10000656-a-c-compressor","title":"Valeo 10000656 A\/C Compressor","description":"\u003ch2\u003eValeo OE A\/C Compressor for Nissan\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is an OEM-standard replacement built for reliable cabin cooling and consistent system performance. It is designed for Nissan NV1500, NV2500, NV3500, and Pathfinder applications across the listed model years, including vehicles that originally used Valeo as the OE supplier.\u003c\/p\u003e\u003cp\u003ePart number 10000656 is part of the Valeo Compressor line, a direct replacement program focused on OE-style fit, function, and materials. For shoppers searching for a Nissan Pathfinder A\/C compressor or a Valeo compressor for NV-series vans, this unit matches the original refrigerant and drive configuration.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo\u003c\/li\u003e\n\u003cli\u003ePart number: 10000656\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for OE-style replacement\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type\u003c\/li\u003e\n\u003cli\u003eDKS compressor design\u003c\/li\u003e\n\u003cli\u003eAluminum core material\u003c\/li\u003e\n\u003cli\u003eSilver finish\u003c\/li\u003e\n\u003cli\u003e7-groove pulley for serpentine belt systems\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo compressors are engineered with quality components to support dependable operation, lower noise, and efficient performance. This compressor is built as a direct replacement for the original unit used on select Nissan NV1500, NV2500, NV3500, and Pathfinder models, making it a practical choice for restoring A\/C function without changing the factory refrigerant or belt setup. Part number 10000656 is also cross-referenced to Four Seasons 58410 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Fix\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the A\/C vents\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement issues\u003c\/li\u003e\n\u003cli\u003eNoise from a worn or failing compressor\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant system performance\u003c\/li\u003e\n\u003cli\u003eUneven or weak cabin cooling in Nissan NV1500, NV2500, NV3500, and Pathfinder models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify refrigerant type before installation; this unit is for R134a systems.\u003c\/li\u003e\n\u003cli\u003eConfirm pulley groove count and serpentine belt routing match the original compressor.\u003c\/li\u003e\n\u003cli\u003eReplace system seals as needed and follow the included installation instructions.\u003c\/li\u003e\n\u003cli\u003eInspect the A\/C system for contamination or leaks before charging.\u003c\/li\u003e\n\u003cli\u003eUse the vehicle-specific fitment notes to confirm the correct Nissan Pathfinder or NV-series application.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo OE compressors are supplied to major vehicle manufacturers worldwide and built to OEM-standard expectations for fit and function. This 10000656 compressor is intended as a direct replacement for the original equipment design used on the listed Nissan applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268296433845,"sku":"BCRR-10000656","price":384.42,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000656_Fro.jpg?v=1775139772"},{"product_id":"valeo-10000658-a-c-compressor","title":"Valeo 10000658 A\/C Compressor","description":"\u003ch2\u003eOE A\/C Compressor for Nissan Altima\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo A\/C compressor, part number 10000658. Built as an OEM-standard direct replacement, it is designed for reliable operation, lower noise, and efficient performance in the 2007-2012 Nissan Altima.\u003c\/p\u003e\u003cp\u003eValeo’s Compressor line focuses on OE-style fit and function for drivers who want a replacement that matches the original system layout. This unit uses R134a refrigerant, includes the clutch, and comes with oil and installation instructions for a more straightforward service job.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDirect replacement A\/C compressor for HVAC systems\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Nissan Altima, N\/A\u003c\/li\u003e\n\u003cli\u003eValeo OE family, OEM Standard grade\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with ZXL100PG compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003e6-groove pulley and serpentine belt design\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eOil included; fluid capacity 150cc\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo 10000658 is engineered as a direct-fit A\/C compressor for the Nissan Altima, 2007-2012. It is built with quality components to support dependable cooling performance while helping reduce operating noise and fuel consumption compared with a worn or failing compressor. The aluminum construction, 6-groove pulley, and serpentine belt configuration align with the original system design for a clean replacement on the Nissan Altima platform. This part cross-references Four Seasons 68664 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWarm air from the vents when the A\/C system is engaged\u003c\/li\u003e\n\u003cli\u003eCompressor noise, grinding, or clutch-related operation issues\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant circulation through the HVAC system\u003c\/li\u003e\n\u003cli\u003eReduced cooling performance during idle or stop-and-go driving\u003c\/li\u003e\n\u003cli\u003eFailure of the original compressor on a 2007-2012 Nissan Altima\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, pulley groove count, and belt configuration before installation. Flush the system as needed, replace worn seals, and follow the included instructions during service. Use the specified ZXL100PG compatible refrigerant oil and confirm the system is properly evacuated and charged after installation. Fits 2007-2012 Nissan Altima, N\/A.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level components used by major vehicle manufacturers worldwide, and this compressor is built to OEM Standard requirements for fit and performance. Part number 10000658 is intended for direct replacement service on the Nissan Altima application listed above.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268296597685,"sku":"BCRR-10000658","price":345.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000658_Fro.jpg?v=1775139772"},{"product_id":"valeo-10000660-a-c-compressor","title":"Valeo 10000660 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Nissan Sentra\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo A\/C compressor, part number 10000660. Built as an OEM-standard replacement, it uses high-quality components for reliable operation, lower noise, and efficient performance in daily driving.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo OE compressor line for direct replacement applications\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade with aluminum core material\u003c\/li\u003e\n\u003cli\u003eDesigned for R134a refrigerant and XLE 100PG compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eClutch included with serpentine belt drive and 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eOil included, 150 mL fluid capacity, and installation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets and O-rings for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThe Valeo Compressor line is built for drivers who want OE-style fit and function without changing the original system setup. This silver DCS-style A\/C compressor is engineered for the 2007-2012 Nissan Sentra and the 2009 Nissan Sentra built from 03\/09, matching the vehicle’s refrigerant and belt-drive requirements. Part number 10000660 is also a practical search term for shoppers comparing OE replacement options for Nissan Sentra air conditioning repair.\u003c\/p\u003e\u003cp\u003eValeo supplies compressors to major vehicle manufacturers worldwide, and this replacement follows that OE-focused approach with the same type of component quality expected in factory-installed HVAC systems. This part cross-references Four Seasons 68662 and Global Parts Distributors LLC 6512330 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the vents\u003c\/li\u003e\n\u003cli\u003eCompressor noise or rough operation\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C system pressure\u003c\/li\u003e\n\u003cli\u003eWeak cooling performance in a Nissan Sentra\u003c\/li\u003e\n\u003cli\u003eFailure of the original compressor clutch or internal components\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, pulley groove count, and belt configuration before installation. Replace the system oil with the specified XLE 100PG type, follow the included instructions, and use the supplied gaskets and O-rings during assembly. Proper evacuation, leak checking, and recharge procedures are required after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo OE compressors are built to OEM-standard specifications with components selected for reliability and consistent performance. This part number 10000660 is a direct replacement for the listed Nissan Sentra applications and is backed by Valeo’s OE-focused manufacturing approach.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268297285813,"sku":"BCRR-10000660","price":383.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000660_Fro.jpg?v=1775139772"},{"product_id":"valeo-10000664-a-c-compressor","title":"Valeo 10000664 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Honda and Acura\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling performance with this Valeo A\/C compressor, part number 10000664. Built with OEM-standard construction and an aluminum core, it is a direct replacement for select Honda Odyssey, Honda Pilot, and Acura MDX applications.\u003c\/p\u003e\u003cp\u003eValeo’s Compressor line focuses on reliable operation, lower noise, and efficient performance. This unit includes the clutch and uses a serpentine belt drive, making it a practical replacement for vehicles that need a factory-style A\/C compressor service part.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line A\/C compressor, part number 10000664\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for direct replacement service\u003c\/li\u003e\n\u003cli\u003eSilver finish with aluminum core material\u003c\/li\u003e\n\u003cli\u003eClutch included for complete compressor replacement\u003c\/li\u003e\n\u003cli\u003eSerpentine belt type with 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eUses R13a refrigerant type\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eIncludes gaskets \/ O-rings for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eThis Valeo 10000664 A\/C compressor is built for drivers who need a factory-style replacement that matches the original system layout. It is designed for 1999-2004 Honda Odyssey, 2003-2004 Honda Pilot, and 2001-2002 Acura MDX models, with fitment listed as compressor application only. The Valeo Compressor product line is engineered with quality components to support dependable operation and reduced noise levels, helping maintain comfortable cabin cooling in daily driving.\u003c\/p\u003e\u003cp\u003eThis part cross-references Four Seasons 78342 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent air conditioning output\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor seizure or internal wear\u003c\/li\u003e\n\u003cli\u003eLoss of cabin cooling performance in Honda Odyssey, Honda Pilot, and Acura MDX models\u003c\/li\u003e\n\u003cli\u003eFactory-style replacement needs for OE-standard service\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, pulley groove count, and belt configuration before installation. Replace the included gaskets \/ O-rings during service, follow the supplied instructions, and evacuate and recharge the system according to the vehicle service procedure. Confirm the compressor mounting and clutch connection match the original setup on your Honda Odyssey, Honda Pilot, or Acura MDX.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo manufactures this compressor to OEM-standard expectations using components selected for reliability and consistent performance. The design reflects the same type of direct-replacement part supplied to major vehicle manufacturers worldwide.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268297351349,"sku":"BCRR-10000664","price":340.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000664_Fro.jpg?v=1775139773"},{"product_id":"valeo-10000665-a-c-compressor","title":"Valeo 10000665 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Acura TL\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is a direct replacement for the factory unit on 2004-2008 Acura TL models. Built to OEM standard and supplied with clutch, oil, and installation instructions, it is designed for dependable cabin cooling with controlled noise and efficient operation.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2004-2008 Acura TL, compressor application\u003c\/li\u003e\n\u003cli\u003eValeo Compressor line engineered for OE-style replacement fit and function\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant system with PAG 46 oil specification\u003c\/li\u003e\n\u003cli\u003e10S compressor type with 6-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included for a complete compressor assembly\u003c\/li\u003e\n\u003cli\u003eOil included; fluid capacity listed at 200 mL\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings included for sealing during installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Part Number 10000665 is built for Acura TL A\/C service where a direct-fit compressor replacement is needed. The Valeo Compressor product line focuses on reliable components and OE-standard construction, helping maintain consistent refrigerant circulation and stable air conditioning performance. This unit is specified for R134a systems and uses PAG 46 oil, making it a practical match for the listed vehicle application. Part number 10000665 is also cross-referenced to Four Seasons 98307 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible with 2004, 2005, 2006, 2007, and 2008 Acura TL models, this compressor supports factory-style HVAC repair on the Acura TL platform. The included clutch and sealing components help streamline replacement work when servicing a worn, noisy, or non-functioning compressor.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the A\/C vents\u003c\/li\u003e\n\u003cli\u003eCompressor noise, bearing wear, or clutch-related failure\u003c\/li\u003e\n\u003cli\u003eRefrigerant circulation loss in the HVAC system\u003c\/li\u003e\n\u003cli\u003eUneven or weak cabin cooling\u003c\/li\u003e\n\u003cli\u003eLeak-related compressor replacement needs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and compressor type before installation. Flush the system as needed, replace damaged seals, and follow the included instructions during service. Proper evacuation and recharge procedures are important after compressor replacement on Acura TL A\/C systems.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-standard compressor components and manufactures products used by major vehicle makers worldwide. This compressor is built with high-quality materials and designed for reliable operation in the specified Acura TL application.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268297515189,"sku":"BCRR-10000665","price":329.32,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000665_Fro.jpg?v=1775139773"},{"product_id":"valeo-10000666-a-c-compressor","title":"Valeo 10000666 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Toyota and Lexus\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is built for direct replacement service on select Toyota and Lexus applications. It uses an aluminum core, R134a refrigerant, and PAG 46 oil compatibility to support dependable cabin cooling in vehicles such as the Toyota Camry, Highlander, Avalon, Solara, and Lexus ES330, RX330, ES300, and RX300.\u003c\/p\u003e\u003cp\u003eValeo Compressor line products are engineered as OEM-standard replacements, with the same type of quality used in original vehicle production programs. Part number 10000666 is designed for vehicles with a 5-groove serpentine belt setup and includes the clutch for a more complete compressor replacement.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo Compressor\u003c\/li\u003e\n\u003cli\u003ePart number: 10000666\u003c\/li\u003e\n\u003cli\u003eOEM Standard grade for direct replacement service\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with PAG 46 oil compatibility\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets \/ O-rings for installation hardware\u003c\/li\u003e\n\u003cli\u003e5-groove pulley design for serpentine belt applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Product Overview\u003c\/h2\u003e\u003cp\u003eValeo 10000666 is an A\/C compressor built for select Toyota and Lexus vehicles that use a 5-groove compressor drive. It is a direct replacement part for 2000-2004 Toyota Avalon, 2001-2006 Toyota Highlander, 2002-2006 Toyota Camry, 2004-2008 Toyota Solara, 2002-2003 Lexus ES300, 1999-2003 Lexus RX300, 2004-2006 Lexus ES330, and 2004-2006 Lexus RX330. This part cross-references Delphi CS20071 and Four Seasons 78390 for the same application.\u003c\/p\u003e\u003cp\u003eThe compressor is designed to help maintain stable A\/C performance while supporting lower noise levels and efficient operation. With the clutch included and OEM-standard construction, it is a practical replacement for restoring factory-style air conditioning performance on Toyota Camry and Lexus RX330 service jobs, as well as other listed fitments.\u003c\/p\u003e\u003ch2\u003eWhat This Compressor Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor failure from worn internal components\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C performance in R134a systems\u003c\/li\u003e\n\u003cli\u003eDrive belt engagement issues related to the compressor clutch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle uses a 5-groove serpentine belt compressor setup before installation. Replace the receiver\/drier or accumulator and inspect the system for contamination, leaks, and debris before charging. Use the specified PAG 46 oil and the correct R134a refrigerant charge for the vehicle application. Follow the included installation instructions and verify pulley alignment, clutch operation, and system pressures after service.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OEM-standard compressor components built with high-quality materials for reliable service and consistent performance. Part number 10000666 is produced as a direct replacement for the listed Toyota and Lexus applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268297547957,"sku":"BCRR-10000666","price":337.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000666_Fro.jpg?v=1775139773"},{"product_id":"valeo-10000668-a-c-compressor","title":"Valeo 10000668 A\/C Compressor","description":"\u003ch2\u003eOE-Style A\/C Compressor for Chrysler Pacifica\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is a direct replacement for select 2004-2006 Chrysler Pacifica models. Built with OEM-standard components, it supports reliable cabin cooling, quieter operation, and consistent performance for everyday driving.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eBrand: Valeo Compressor line\u003c\/li\u003e\n\u003cli\u003ePart number: 10000668\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Chrysler Pacifica, compressor\u003c\/li\u003e\n\u003cli\u003eRefrigerant type: R134a\u003c\/li\u003e\n\u003cli\u003eCompatible with PAG 46 refrigerant oil\u003c\/li\u003e\n\u003cli\u003e10S compressor design with 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eOil included\u003c\/li\u003e\n\u003cli\u003eAluminum core construction\u003c\/li\u003e\n\u003cli\u003eOEM standard grade\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets \/ O-rings included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Compressor line focuses on direct-fit HVAC replacement parts built to match original equipment requirements. This compressor uses an aluminum core, comes preconfigured for R134a refrigerant, and is specified for PAG 46 oil. The 10S design, 6-groove pulley, and serpentine belt setup support proper belt alignment and system operation in the Chrysler Pacifica cooling system. Part number 10000668 is also referenced by cross numbers such as Delphi CS20119 and Four Seasons 68342 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent air conditioning output\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement issues\u003c\/li\u003e\n\u003cli\u003eRefrigerant circulation problems in the A\/C system\u003c\/li\u003e\n\u003cli\u003eLoss of cabin cooling performance in a 2004-2006 Chrysler Pacifica\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil specification, pulley groove count, and belt drive configuration before installation. Replace the included gaskets \/ O-rings during service, follow the supplied instructions, and evacuate and recharge the system according to factory procedures. Flush the system as needed if the previous compressor failed internally.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components used by major vehicle manufacturers worldwide. This compressor is built to OEM standard specifications for direct replacement service on the Chrysler Pacifica platform.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268297777333,"sku":"BCRR-10000668","price":333.9,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000668_Fro.jpg?v=1775139774"},{"product_id":"valeo-10000671-a-c-compressor","title":"Valeo 10000671 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Neon\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo A\/C compressor, part number 10000671. Built with OEM-standard construction and supplied with clutch, oil, and installation instructions, it is a direct replacement for select Dodge Neon and Plymouth Neon applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line for OE-style HVAC replacement\u003c\/li\u003e\n\u003cli\u003ePart number 10000671 for accurate ordering and service lookup\u003c\/li\u003e\n\u003cli\u003eFits R134a refrigerant systems with PAG 46 oil\u003c\/li\u003e\n\u003cli\u003e10S compressor design with 4-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core construction with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included\u003c\/li\u003e\n\u003cli\u003eOil included; fluid capacity listed at 200 mL\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eUses gaskets \/ O-rings for installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo Compressor 10000671 is an OEM-standard A\/C compressor engineered for reliable refrigerant circulation and consistent HVAC performance. It is designed for R134a systems and uses PAG 46 oil, making it a direct replacement choice for 2000-2001 Dodge Neon and 2000-2001 Plymouth Neon compressor applications. The compressor features a 10S design, aluminum core material, a 4-groove pulley, and serpentine belt compatibility for straightforward service matching. This part cross-references Four Seasons 78378 and Global Parts Distributors LLC 6512112 for the same application.\u003c\/p\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2000-2001 Dodge Neon, compressor\u003c\/li\u003e\n\u003cli\u003eFits 2000-2001 Plymouth Neon, compressor\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eCommon Repair Uses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNo cold air from the vents\u003c\/li\u003e\n\u003cli\u003eCompressor clutch engagement problems\u003c\/li\u003e\n\u003cli\u003eExcessive A\/C system noise\u003c\/li\u003e\n\u003cli\u003eRefrigerant circulation loss in the HVAC system\u003c\/li\u003e\n\u003cli\u003eReplacement for a worn or seized compressor on Neon models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm refrigerant type, oil specification, pulley groove count, and belt routing before installation. Replace the listed gaskets and O-rings during service, evacuate and recharge the system to the correct specification, and follow the included instructions for proper setup on 2000-2001 Dodge Neon and Plymouth Neon vehicles.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies compressors built to OEM-standard requirements and used in vehicle manufacturer applications worldwide. This product is intended as a direct replacement with the same type of component quality associated with Valeo original equipment programs.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268298793141,"sku":"BCRR-10000671","price":326.82,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000671_Fro.jpg?v=1775139774"},{"product_id":"valeo-10000680-a-c-compressor","title":"Valeo 10000680 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Jeep Liberty\u003c\/h2\u003e\u003cp\u003eThis Valeo A\/C compressor is an OEM-standard replacement built for reliable cabin cooling and consistent system performance. It is designed for 2002-2005 Jeep Liberty models and uses R134a refrigerant with PAG 46 oil for the specified application.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eValeo Compressor line A\/C compressor, part number 10000680\u003c\/li\u003e\n\u003cli\u003eDirect replacement for 2002-2005 Jeep Liberty compressor applications\u003c\/li\u003e\n\u003cli\u003eSD7 compressor type with aluminum core material\u003c\/li\u003e\n\u003cli\u003eClutch included for a complete compressor assembly\u003c\/li\u003e\n\u003cli\u003eUses R134a refrigerant and PAG 46 compatible refrigerant oil\u003c\/li\u003e\n\u003cli\u003eSerpentine belt drive with 6-groove pulley\u003c\/li\u003e\n\u003cli\u003eOEM standard grade for factory-style fit and function\u003c\/li\u003e\n\u003cli\u003eOil included with 180 mL fluid capacity\u003c\/li\u003e\n\u003cli\u003eInstallation instructions included\u003c\/li\u003e\n\u003cli\u003eGaskets and O-rings specified for installation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Compressor products are built with quality components to support dependable operation, lower noise, and efficient performance in the vehicle HVAC system. This A\/C compressor is a direct replacement for the original unit used on Jeep Liberty models from 2002 through 2005, making it a practical choice when restoring cooling performance. The Valeo 10000680 is also referenced by Delphi CS20144, Four Seasons 98576, Global Parts Distributors LLC 6511261, and UAC CO4335C for the same application.\u003c\/p\u003e\u003cp\u003eCompatible with 2002-2005 Jeep Liberty, compressor position. The Valeo 10000680 is a fitment-specific solution for drivers searching for a Jeep Liberty A\/C compressor replacement, Jeep Liberty air conditioning compressor, or OEM-standard HVAC compressor for 2002-2005 Jeep Liberty models.\u003c\/p\u003e\u003ch2\u003eCommon Issues This Part Addresses\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent cabin cooling\u003c\/li\u003e\n\u003cli\u003eNoisy compressor operation\u003c\/li\u003e\n\u003cli\u003eCompressor seizure or internal wear\u003c\/li\u003e\n\u003cli\u003eLoss of A\/C system pressure from a failed compressor\u003c\/li\u003e\n\u003cli\u003eRestoration of factory-style HVAC performance on Jeep Liberty models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify refrigerant type, oil type, and pulley groove count before installation. Replace the specified gaskets and O-rings during service, and follow the included instructions for proper compressor installation. Always evacuate and recharge the A\/C system according to the vehicle service procedure after replacing the compressor.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level HVAC components to major vehicle manufacturers worldwide, and this compressor is built to OEM standard for the listed Jeep Liberty applications. The design focuses on reliable operation and consistent performance in the vehicle air conditioning system.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268300038325,"sku":"BCRR-10000680","price":298.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000680_Fro.jpg?v=1775139774"},{"product_id":"valeo-10000709-a-c-compressor","title":"Valeo 10000709 A\/C Compressor","description":"\u003ch2\u003eValeo A\/C Compressor for Audi and Volkswagen\u003c\/h2\u003e\u003cp\u003eRestore cabin cooling with this Valeo Compressor A\/C compressor, part number 10000709. Built to OEM standard with an aluminum core, clutch included, and oil included, it is a direct replacement for select Audi and Volkswagen applications that use R134a refrigerant and PAG 46 oil.\u003c\/p\u003e\u003cp\u003eValeo Compressor products are built with quality components for reliable operation, lower noise, and efficient performance. This compressor is designed for drivers who need a factory-style replacement for Audi A4, A6, A8, S4, S6, S8, RS6, Allroad Quattro, and Volkswagen Passat HVAC systems.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePart number: 10000709\u003c\/li\u003e\n\u003cli\u003eOEM standard A\/C compressor for select Audi and Volkswagen vehicles\u003c\/li\u003e\n\u003cli\u003eR134a refrigerant type with PAG 46 compatible oil\u003c\/li\u003e\n\u003cli\u003e7SBU compressor type with 6-groove serpentine pulley\u003c\/li\u003e\n\u003cli\u003eAluminum core material with silver finish\u003c\/li\u003e\n\u003cli\u003eClutch included and installation instructions included\u003c\/li\u003e\n\u003cli\u003eOil included; fluid capacity listed at 170 mL\u003c\/li\u003e\n\u003cli\u003eUses gasket and O-ring installation hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThis Valeo Compressor compressor is engineered as a direct replacement for factory air conditioning systems that require OE-style fit and function. It is built for select 1997-2005 Audi A4, A4 Quattro, A6, A6 Quattro, A8, A8 Quattro, S4, S6, S8, RS6, and Allroad Quattro models, plus 1998-2005 Volkswagen Passat applications. The design supports consistent compressor operation, reduced noise, and dependable cooling performance in daily driving conditions.\u003c\/p\u003e\u003cp\u003eThis part cross-references Four Seasons 78313 and UAC CO105109C for the same application. The part number 10000709 is also useful when verifying replacement needs against OE and aftermarket listings.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Compressor Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eWeak or inconsistent A\/C cooling\u003c\/li\u003e\n\u003cli\u003eCompressor noise from worn internal components\u003c\/li\u003e\n\u003cli\u003eLoss of refrigerant pressure due to compressor failure\u003c\/li\u003e\n\u003cli\u003eClutch-related A\/C engagement issues\u003c\/li\u003e\n\u003cli\u003eRestoring factory-style HVAC performance on Audi and Volkswagen vehicles\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm vehicle fitment by year, model, and VIN notes before installation. This compressor uses R134a refrigerant and PAG 46 oil, so the system should be serviced with the correct refrigerant and lubricant specification. Replace the listed gaskets and O-rings during installation, evacuate the system properly, and inspect the condenser, expansion device, and lines for contamination before charging.\u003c\/p\u003e\u003cp\u003eFits 2001-2005 Audi Allroad Quattro, compressor; 1998-2005 Volkswagen Passat, compressor; 1997-2004 Audi A6 Quattro, compressor; 2001-2003 Audi A8 Quattro, compressor; 1999 Audi A8 Quattro, compressor; 1997 Audi A8 Quattro, compressor; 2003 Audi RS6, compressor; 2002-2003 Audi S6, compressor; 2001-2003 Audi S8, compressor; 2000-2002 Audi S4, compressor; 1998-2001 Audi A4, compressor; 1998-2001 Audi A4 Quattro, compressor; 1998-2001 Audi A6, compressor.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo supplies OE-level compressor components to major vehicle manufacturers worldwide, and this replacement is built to the same OEM standard expected for factory service applications. The included installation instructions support a more accurate repair process for Audi and Volkswagen A\/C system service.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268300791989,"sku":"BCRR-10000709","price":438.13,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_10000709_Fro_8a82bd87-add3-4722-b2fb-90d2f49ce872.jpg?v=1775139775"},{"product_id":"valeo-101822-alternator","title":"Valeo 101822 Alternator","description":"\u003ch2\u003eValeo 101822 Alternator Overview\u003c\/h2\u003e\u003cp\u003eThe Valeo 101822 alternator is a 12-volt charging system component built for consistent electrical output in classic Porsche applications. It features an internal regulator, external fan design, clockwise rotation, and a 50 amp rating for the 1974-1977 Porsche 911.\u003c\/p\u003e\u003cp\u003eAs part of the Valeo OE alternator family, this unit follows original equipment specifications for the 911 platform and is supplied as a 100% new alternator. That helps reduce the risk associated with remanufactured units while supporting stable charging performance.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12-volt alternator with 50 amp output\u003c\/li\u003e\n\u003cli\u003eInternal regulator for simplified charging control\u003c\/li\u003e\n\u003cli\u003eExternal fan design\u003c\/li\u003e\n\u003cli\u003eClockwise rotation direction\u003c\/li\u003e\n\u003cli\u003eValeo OE family construction\u003c\/li\u003e\n\u003cli\u003eTechnical number: A13N281\u003c\/li\u003e\n\u003cli\u003eSupplied without pulley\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eValeo 101822 is an OE-style alternator engineered for the 1974-1977 Porsche 911, where dependable charging output is critical for ignition, lighting, and accessory operation. Valeo has supplied original equipment electrical components for decades, and this alternator reflects that OE-focused approach with a 12V internal-regulator design and 50 amp amperage rating. The Valeo 101822 alternator is a direct-fit solution for Porsche 911 charging system service when the original unit is worn, unstable, or no longer maintaining proper voltage.\u003c\/p\u003e\u003cp\u003eThis part cross-references Bosch 13025 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eLow charging voltage at the battery\u003c\/li\u003e\n\u003cli\u003eDim headlights or unstable electrical output\u003c\/li\u003e\n\u003cli\u003eBattery drain caused by alternator failure\u003c\/li\u003e\n\u003cli\u003eCharging warning light concerns\u003c\/li\u003e\n\u003cli\u003eNoisy or inconsistent alternator operation\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify pulley requirements before installation, since this alternator is listed without a pulley. Confirm the clockwise rotation, 12-volt system, and internal regulator configuration against the original unit before fitting. For Porsche 911 charging system service, compare the technical number A13N281 and the OE-style mounting points to ensure proper alignment and belt setup.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo is a long-standing OE supplier in electrical systems, and this alternator is built as a new unit rather than a remanufactured assembly. That construction supports consistent output and reduces the uncertainty associated with reused internal components.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268301217973,"sku":"BCRR-101822","price":328.96,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_101822_Fro.jpg?v=1775139775"},{"product_id":"valeo-11-windshield-wiper-blade","title":"Valeo 11 Windshield Wiper Blade - Front Left, Front Right or Rear","description":"\u003ch2\u003eValeo 11 Conventional Rear Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Traditional wiper blade is a conventional replacement built for steady rear-window wiping performance. With an 11-inch rubber wiping edge, steel backbone, and A2 hook-style connector, this Valeo 11 blade is a direct choice for vehicles that use a traditional rear wiper arm.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e11 in blade length for rear and select front-right applications\u003c\/li\u003e\n\u003cli\u003eConventional wiper blade design\u003c\/li\u003e\n\u003cli\u003eRubber wiping element for consistent contact on the glass\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eA2 connector type: Hook 9x3\/9x4 combo hook slot 7x2.5\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Line Details\u003c\/h2\u003e\u003cp\u003eValeo Ultimate Traditional focuses on conventional replacement blades that follow OEM-style engineering principles. The line is built for drivers who need a straightforward replacement for hook-arm applications, including rear wiper service on vehicles such as the Chevrolet Tahoe, GMC Yukon, and Toyota Sequoia.\u003c\/p\u003e\u003ch2\u003eFitment and Application\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2022-2023 Chevrolet Tahoe, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2023 GMC Yukon, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021-2022 Buick Encore GX, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021-2022 Chevrolet Blazer, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Cadillac XT4, rear\u003c\/li\u003e\n\u003cli\u003eFits 2017-2021 Cadillac XT5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020-2021 Cadillac XT6, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021 Chevrolet Tahoe, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021 GMC Yukon, rear\u003c\/li\u003e\n\u003cli\u003eFits 2008-2021 Toyota Sequoia, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020 Buick Encore GX, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2020 Buick Envision, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2020 Chevrolet Blazer, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2020 Chevrolet Bolt EV, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020 Chevrolet Equinox, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020 GMC Terrain, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018 GMC Terrain, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2019 Chevrolet Equinox, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019 GMC Terrain, rear\u003c\/li\u003e\n\u003cli\u003eFits 2014-2018 Nissan Versa Note, front right\u003c\/li\u003e\n\u003cli\u003eFits 2013-2016 GMC Acadia, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2016 Jeep Compass, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2014 Cadillac SRX, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Dodge Caliber, rear\u003c\/li\u003e\n\u003cli\u003eFits 2011-2012 Dodge Nitro, rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Hummer H3, rear\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 Hummer H2, rear\u003c\/li\u003e\n\u003cli\u003eFits 2008 Mazda 6, rear\u003c\/li\u003e\n\u003cli\u003eFits 2002-2007 Jeep Liberty, rear\u003c\/li\u003e\n\u003cli\u003eFits 2002-2007 Saturn Vue, rear\u003c\/li\u003e\n\u003cli\u003eFits 2002-2006 Honda CR-V, rear\u003c\/li\u003e\n\u003cli\u003eFits 2006 Hummer H1, front left\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Hummer H1, front left\u003c\/li\u003e\n\u003cli\u003eFits 2006 Hummer H1, front right\u003c\/li\u003e\n\u003cli\u003eFits 2002-2004 Hummer H1, front right\u003c\/li\u003e\n\u003cli\u003eFits 1994-2004 Jeep Grand Cherokee, rear\u003c\/li\u003e\n\u003cli\u003eFits 1996-2004 Nissan Pathfinder, rear\u003c\/li\u003e\n\u003cli\u003eFits 1997-2003 INFINITI QX4, rear\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 BMW Z3, rear\u003c\/li\u003e\n\u003cli\u003eFits 1985-1989 Volvo 740, rear\u003c\/li\u003e\n\u003cli\u003eFits 1985 Volvo 745, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass caused by worn rubber\u003c\/li\u003e\n\u003cli\u003eSkipping or chatter from an aging conventional blade\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain, sleet, or road spray\u003c\/li\u003e\n\u003cli\u003eUneven wiping from a fatigued steel-backed blade\u003c\/li\u003e\n\u003cli\u003eFitment issues on hook-arm rear wiper applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the arm style before ordering; this blade uses an A2 hook connector for 9x3 and 9x4 hook-slot applications. Match the 11-inch length to the vehicle position listed in the fitment data, and verify the rear wiper arm clears the glass edge through a full sweep after installation. This part cross-references ANCO 31-11 and TRICO 11-1 for the same application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM engineering practices with conventional blade construction to deliver a replacement wiper built for dependable service on the specified applications. The Ultimate Traditional line is designed around proven materials and connector compatibility for routine maintenance on vehicles such as the Chevrolet Tahoe, GMC Yukon, and Toyota Sequoia.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268301250741,"sku":"BCRR-11","price":24.83,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_11_Fro.jpg?v=1775139775"},{"product_id":"valeo-11v-windshield-wiper-blade","title":"Valeo 11V Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade for Rear Visibility\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade is a beam-style rear blade built for consistent wiping performance and a secure V-Notch connection. This 11-inch Valeo 11V rear wiper blade is a direct fit for select Volkswagen Passat wagon applications and is engineered with OEM-focused design principles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e11-inch rear wiper blade length\u003c\/li\u003e\n\u003cli\u003eBeam-style blade design for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge\u003c\/li\u003e\n\u003cli\u003eSteel backbone for blade support\u003c\/li\u003e\n\u003cli\u003eV-Notch connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eBuilt under the Valeo Ultimate Rear product line, this blade reflects the brand’s OE-oriented engineering approach for rear wiper applications. The beam construction helps maintain contact on the rear window, while the rubber element and steel backbone work together to support steady wiping action. The Valeo 11V is a practical replacement choice for drivers servicing a 2006-2010 Volkswagen Passat rear wiper system with a wagon body style and V-Notch arm type.\u003c\/p\u003e\u003cp\u003eThis part cross-references TRICO 11-G for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wiping across the rear window\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber that no longer clears moisture cleanly\u003c\/li\u003e\n\u003cli\u003eFitment issues on rear wiper arms using a V-Notch connector\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eFits 2006-2010 Volkswagen Passat, rear. Confirm the rear arm uses a V-Notch connector and verify the 11-inch blade length before installation. Remove the old blade carefully, align the connector, and seat the new blade fully on the arm before testing rear wipe coverage.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo designs this rear wiper blade with OEM engineering and product-line consistency used by major vehicle manufacturers and automotive professionals worldwide. The beam-style construction, rubber wiping edge, and steel backbone are selected to support dependable rear-window cleaning performance.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268303675573,"sku":"BCRR-11V","price":21.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_11V_Fro.jpg?v=1775139775"},{"product_id":"valeo-12a-windshield-wiper-blade","title":"Valeo 12A Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 12A\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade 12A is a 12-inch beam-style rear blade built for consistent wiping performance and a clean rear window view. It uses a rubber wiping edge with a steel backbone and composite BBI construction to support stable contact across the glass.\u003c\/p\u003e\u003cp\u003eDesigned for rear applications on a wide range of vehicles, this Valeo Ultimate Rear blade is a direct replacement for many Lexus, Toyota, Hyundai, Mazda, and Dodge rear wiper setups with Roc Lock 2 or RL2-style arms. The 12A part number is also a useful cross-reference when matching OE-style rear blade applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12-inch rear wiper blade for rear window service\u003c\/li\u003e\n\u003cli\u003eBeam-style design for even pressure across the wiping surface\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear visibility\u003c\/li\u003e\n\u003cli\u003eSteel backbone with BBI\/composite blade construction\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for listed applications\u003c\/li\u003e\n\u003cli\u003eOE-engineered design from Valeo Ultimate Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo combines OEM-focused engineering with a rear blade design intended for dependable everyday use. The Ultimate Rear line is built for vehicles that use a 12-inch rear blade, including many Toyota RAV4, Toyota 4Runner, Lexus NX, Lexus GX460, Hyundai Palisade, and Mazda CX-90 rear applications. Part number 12A is commonly referenced in rear wiper blade searches for these fitments and related OE replacements.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO AR-12A and Bosch 18121 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wiping on the back window\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber edges that leave water behind\u003c\/li\u003e\n\u003cli\u003eNoise caused by an aging rear wiper blade\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear arm style before ordering. This blade is listed for Roc Lock 2 Type Arm and RL2-style rear applications, depending on vehicle year and model. Confirm the 12-inch length and match the vehicle-specific rear fitment before installation. Clean the rear glass and inspect the arm for wear or damage before fitting the new blade.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2025-2026 Lexus LX700h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2026 Lexus TX500h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2026 Lexus TX550h+, rear\u003c\/li\u003e\n\u003cli\u003eFits 2025-2026 Lexus UX300h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2026 Mazda CX-90, rear\u003c\/li\u003e\n\u003cli\u003eFits 2025-2026 Toyota Crown Signia, rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2026 Toyota Grand Highlander, rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2025 Chevrolet Equinox, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020-2025 Dodge Durango, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Hyundai Ioniq 5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2025 Hyundai Ioniq 5 N, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Hyundai Palisade, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Land Rover Discovery Sport, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Lexus LX600, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Lexus NX250, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Lexus NX350, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Lexus NX350h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Lexus NX450h+, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Toyota RAV4, rear\u003c\/li\u003e\n\u003cli\u003eFits 2015-2018 Toyota RAV4, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Toyota Sienna, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 GMC Terrain, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Lexus UX250h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021-2024 Mitsubishi Mirage, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Toyota 4Runner, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021-2024 Toyota RAV4 Prime, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2023 Lexus GX460, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022 Lexus UX200, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020-2021 Hyundai Palisade, rear\u003c\/li\u003e\n\u003cli\u003eFits 2015-2021 Land Rover Discovery Sport, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2021 Lexus GX460, rear\u003c\/li\u003e\n\u003cli\u003eFits 2013-2021 Lexus LX570, rear\u003c\/li\u003e\n\u003cli\u003eFits 2008-2011 Lexus LX570, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2021 Lexus NX300, rear\u003c\/li\u003e\n\u003cli\u003eFits 2015-2021 Lexus NX300h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Lexus UX200, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Lexus UX250h, rear\u003c\/li\u003e\n\u003cli\u003eFits 2003-2021 Toyota 4Runner, rear\u003c\/li\u003e\n\u003cli\u003eFits 2013-2021 Toyota Land Cruiser, rear\u003c\/li\u003e\n\u003cli\u003eFits 2008-2011 Toyota Land Cruiser, rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Toyota RAV4, rear\u003c\/li\u003e\n\u003cli\u003eFits 2001-2014 Toyota RAV4, rear\u003c\/li\u003e\n\u003cli\u003eFits 2021 Toyota Sienna, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2020 Dodge Journey, rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2020 Jaguar XF, rear\u003c\/li\u003e\n\u003cli\u003eFits 2014-2020 Mitsubishi Mirage, rear\u003c\/li\u003e\n\u003cli\u003eFits 2011-2019 Dodge Durango, rear\u003c\/li\u003e\n\u003cli\u003eFits 2011-2019 Fiat 500, rear\u003c\/li\u003e\n\u003cli\u003eFits 2001-2019 Toyota Highlander, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Chevrolet Spark Classic, rear\u003c\/li\u003e\n\u003cli\u003eFits 2009-2017 Dodge Journey, rear\u003c\/li\u003e\n\u003cli\u003eFits 2015-2017 Lexus NX200t, rear\u003c\/li\u003e\n\u003cli\u003eFits 2017 Mazda 3, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2015 Mazda 3, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Mazda 3 Sport, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2017 Mazda 5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2014-2017 Suzuki Grand Vitara, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016 Hyundai Tucson, rear\u003c\/li\u003e\n\u003cli\u003eFits 2016 Mazda 3, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2016 Toyota Yaris, rear\u003c\/li\u003e\n\u003cli\u003eFits 2012-2015 Chevrolet Spark, rear\u003c\/li\u003e\n\u003cli\u003eFits 2012-2015 Mazda 5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2010 Mazda 5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2009-2015 Toyota Venza, rear\u003c\/li\u003e\n\u003cli\u003eFits 2009-2014 Toyota Matrix, rear\u003c\/li\u003e\n\u003cli\u003eFits 2012-2014 Toyota Prius V, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2013 Kia Forte, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2013 Kia Forte Koup, rear\u003c\/li\u003e\n\u003cli\u003eFits 2012-2013 Kia Forte5, rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2013 Suzuki Grand Vitara, rear\u003c\/li\u003e\n\u003cli\u003eFits 2011 Chevrolet Spark, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2011 Mitsubishi Endeavor, rear\u003c\/li\u003e\n\u003cli\u003eFits 2009-2010 Fiat 500, rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2007 Mazda 6, rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Scion xA, rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo’s Ultimate Rear line is backed by the brand’s OEM engineering approach and is trusted across major vehicle manufacturer applications. The 12A rear blade is built to meet the demands of rear-window wiping on a broad range of Lexus, Toyota, Hyundai, Mazda, and Dodge vehicles.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268316553397,"sku":"BCRR-12A","price":16.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_12A_Fro_7d6e4853-942d-4293-b90f-0704767eccc8.jpg?v=1775139786"},{"product_id":"valeo-12b-windshield-wiper-blade","title":"Valeo 12B Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 12B\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade 12B is a 12-inch beam-style rear blade built for consistent wiping performance and a clean rear window view. It combines Valeo OEM engineering with a composite BBI design for vehicles that use a rear 12-inch blade application.\u003c\/p\u003e\u003cp\u003eCompatible With rear applications on vehicles such as the Acura RDX, Honda HR-V, Jeep Wrangler, Toyota Corolla, and Nissan Murano, this rear wiper blade is built for direct-fit replacement where the original equipment calls for a BBI\/composite rear blade.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12-inch rear wiper blade for rear window service\u003c\/li\u003e\n\u003cli\u003eBeam-style construction for even contact across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear visibility\u003c\/li\u003e\n\u003cli\u003eSteel backbone for added structural support\u003c\/li\u003e\n\u003cli\u003eBBI\/composite blade design for OE-style rear fitment\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for the listed applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Ultimate Rear line focuses on rear wiper applications that require precise fitment and dependable wiping action. The 12B part number is a rear blade solution for a wide range of vehicles, including 2022-2025 Acura RDX, 2023-2025 Honda HR-V, 2022-2025 Jeep Wrangler, 2019-2021 Toyota Corolla, and 2022-2023 Nissan Murano. It also covers many earlier rear applications across Acura, Honda, INFINITI, Jeep, Lexus, Mazda, Mitsubishi, Nissan, Subaru, and Toyota models.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO AR-12B and TRICO 12-B for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wiping across the rear window\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber that no longer clears water effectively\u003c\/li\u003e\n\u003cli\u003eFitment issues on vehicles requiring a 12-inch rear BBI blade\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eVerify the rear arm style and blade length before installation. This blade is listed for rear positions and also includes N\/A fitment notes on select applications where the vehicle uses a specific RL3\/BBI configuration. Confirm the vehicle year, make, model, and rear arm type against the fitment list before ordering.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM-focused engineering with an updated composite blade design to support consistent rear wiping performance. The Ultimate Rear product line is built for drivers who need a direct replacement rear blade with the correct fit and material construction for the listed applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268316651701,"sku":"BCRR-12B","price":16.71,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_12B_Fro_39330ad6-f54f-4551-9d3d-e19df71a0685.jpg?v=1775139786"},{"product_id":"valeo-12e-windshield-wiper-blade","title":"Valeo 12E Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 12E\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade is a 12-inch beam-style rear blade built for consistent wiping performance and a clean rear window. It combines OEM-focused engineering with a composite blade design to serve drivers who need a direct rear wiper replacement for select Nissan, Mitsubishi, Mercedes-Benz, Ford, and other applications.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12 in rear wiper blade length for listed rear applications\u003c\/li\u003e\n\u003cli\u003eBeam-style BBI\/composite blade design for even contact across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear-window performance\u003c\/li\u003e\n\u003cli\u003eSteel backbone for structural support\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for listed applications\u003c\/li\u003e\n\u003cli\u003eValeo Ultimate Rear product line for rear wiper replacement needs\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo part number 12E is part of the Ultimate Rear line, a rear wiper blade family focused on OE-style fit and dependable operation. Valeo uses advanced OEM engineering and a composite beam construction to deliver a rear blade that matches the needs of vehicles using snap-claw and BBI-style rear arm setups. This part cross-references ANCO AR-12E and TRICO 12-E for the same application. It is a strong match for rear wiper service on vehicles such as the Nissan Rogue, Nissan Kicks, and Mitsubishi Outlander when the listed fitment calls for a 12-inch rear blade.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Solve\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped wiping caused by worn rubber\u003c\/li\u003e\n\u003cli\u003eUneven rear-window contact from an aging blade\u003c\/li\u003e\n\u003cli\u003eNoisy operation from a deteriorated rear wiper insert\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain, slush, or road spray\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify rear arm style and blade length before installation. This Valeo 12E rear blade is listed for rear positions and N\/A fitment notes where specified, including BBI composite and snap-claw applications. Confirm the vehicle’s rear wiper arm connection matches the listed fitment before replacing the blade. For vehicles such as the Nissan Rogue, Mitsubishi Outlander, and Mercedes-Benz GLS\/GLE applications, use the exact year and notes shown in the fitment data to ensure proper installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo builds this rear wiper blade with OEM-oriented engineering and materials selected for lasting performance. The Ultimate Rear line reflects Valeo’s focus on products trusted by vehicle manufacturers, automotive professionals, and everyday drivers worldwide.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2022-2026 Nissan Kicks, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Mitsubishi Outlander, rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Nissan Rogue, rear\u003c\/li\u003e\n\u003cli\u003eFits 2020-2024 INFINITI QX60, rear\u003c\/li\u003e\n\u003cli\u003eFits 2015-2025 Nissan X-Trail, rear\u003c\/li\u003e\n\u003cli\u003eFits 2017-2021 Nissan Rogue Sport, rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2018 Ford Focus, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2015 Mercedes-Benz ML350, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 Cadillac Escalade, rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 GMC Yukon, rear\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268316750005,"sku":"BCRR-12E","price":16.05,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_12E_Fro_29c2bc43-b8e0-4e5a-9dd8-74f9857b497c.jpg?v=1775139786"},{"product_id":"valeo-12t-windshield-wiper-blade","title":"Valeo 12T Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear 12T Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 12T is a 12-inch rear wiper blade built in a beam-style design for consistent rear glass wiping. It uses a rubber wiping edge, a steel backbone, and a Cross Pin connector for direct rear wiper arm applications on select Acura, BMW, Ford, Honda, Land Rover, Lincoln, Mini, and Volvo vehicles.\u003c\/p\u003e\u003cp\u003eValeo’s Ultimate Rear line focuses on OE-style engineering and application-specific rear blade design. This part number, 12T, is built for rear wiper service where a beam blade and Cross Pin mounting are required.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12-inch rear wiper blade for rear window service\u003c\/li\u003e\n\u003cli\u003eBeam blade design for even contact across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for rear visibility maintenance\u003c\/li\u003e\n\u003cli\u003eSteel backbone for blade support\u003c\/li\u003e\n\u003cli\u003eCross Pin connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003cli\u003eDirect replacement reference: Valeo 12T\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eVehicle Fitment\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2024-2026 Acura ZDX, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Ford Escape, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Ford Mustang Mach-E, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2023-2025 Honda Civic, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 BMW X3, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Ford Expedition, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Ford Explorer, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2020-2024 Land Rover Defender 110, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2023-2024 Land Rover Defender 130, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2021-2024 Land Rover Defender 90, rear; with Cross Pin type arm.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Lincoln Navigator, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2022-2023 Lincoln Nautilus, rear; wiper blade slightly larger than the original.\u003c\/li\u003e\n\u003cli\u003eFits 2011-2021 BMW X3, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2018-2021 Ford EcoSport, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2013-2021 Ford Escape, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2018-2021 Ford Expedition, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2011-2021 Ford Explorer, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2021 Ford Mustang Mach-E, N\/A; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Lincoln Nautilus, N\/A; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Lincoln Nautilus, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2018-2021 Lincoln Navigator, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2015-2019 Lincoln MKC, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2018-2019 Volvo XC60, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2016-2018 Lincoln MKX, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2013-2016 Mini Cooper Paceman, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2012-2015 BMW 328i, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 BMW 328i GT xDrive, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 BMW 335i GT xDrive, rear; beam technology, Cross Pin arm, 12-inch blade length.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking or uneven wiping on the rear glass\u003c\/li\u003e\n\u003cli\u003eChatter caused by worn rubber or blade fatigue\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain, snow, or road spray\u003c\/li\u003e\n\u003cli\u003eFitment issues on Cross Pin rear wiper arms\u003c\/li\u003e\n\u003cli\u003eReplacement needs for a 12-inch rear beam blade\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the rear arm uses a Cross Pin connector before installation. Verify blade length against the original rear blade when the application notes call for a slightly larger-than-original size. For vehicles such as Ford Escape, Ford Explorer, Ford Expedition, Lincoln Navigator, and Honda Civic, check the rear arm style and mounting point before ordering.\u003c\/p\u003e\u003cp\u003eThis part cross-references ACI 381682 and Pioneer Automotive Industries 604508 for the same application. Additional interchange references include Valeo 12T for rear wiper service on select BMW X3, Ford Mustang Mach-E, and Land Rover Defender applications.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo builds the Ultimate Rear line with OEM-focused engineering and application-specific design used across major vehicle platforms. The beam-style construction, steel backbone, and rubber wiping edge are selected to support consistent rear window cleaning performance on the listed fitments.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268316881077,"sku":"BCRR-12T","price":18.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_12T_Fro.jpg?v=1775139787"},{"product_id":"valeo-12x-windshield-wiper-blade","title":"Valeo 12X Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear 12X Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 12X is a 12-inch beam-style rear wiper blade built for consistent rear glass clearing and stable contact across the sweep. It uses advanced OEM engineering and a steel backbone with a rubber wiping edge to support dependable performance on vehicles that call for a Top Lock 2 rear blade.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e12-inch rear wiper blade for confirmed rear applications\u003c\/li\u003e\n\u003cli\u003eBeam-style design for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge with steel backbone construction\u003c\/li\u003e\n\u003cli\u003eTop Lock 2 connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eDirect replacement part number: 12X\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Ultimate Rear is a product line focused on OE-style rear wiping performance, using engineering practices aligned with major vehicle manufacturers. This Valeo 12X rear wiper blade is specified for vehicles that use a 12-inch beam blade with a TL2\/Top Lock 2 attachment, including Land Rover Discovery, Land Rover Range Rover Velar, Mercedes-Benz G500, Mercedes-Benz G550, Mercedes-Benz G63 AMG, Mercedes-Benz GLA45 AMG, Mercedes-Benz GLC300, Mercedes-Benz GLC350e, Mercedes-Benz GLC43 AMG, Mercedes-Benz GLC250, Mercedes-Benz G65 AMG, and BMW X1 rear applications. This part cross-references TRICO 12-I for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear window\u003c\/li\u003e\n\u003cli\u003eChattering or skipping during operation\u003c\/li\u003e\n\u003cli\u003eUneven wiping across the rear glass\u003c\/li\u003e\n\u003cli\u003eReduced visibility in rain, snow, or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rear blade performance on Land Rover Discovery and Mercedes-Benz rear applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle uses a 12-inch rear blade with a Top Lock 2 connector before installation. Match the connector style and blade length to the existing rear arm, then secure the blade fully before testing the sweep. For fitment examples, this part fits 2022-2025 Land Rover Discovery, rear; fits 2022-2025 Land Rover Range Rover Velar, rear; and fits 2012-2015 BMW X1, rear. It also fits 2018-2021 Mercedes-Benz G500, rear, and fits 2020-2021 Mercedes-Benz GLC300, rear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM-focused engineering with a beam-blade design intended to deliver consistent rear wiping performance. The steel backbone and rubber wiping edge are selected to support stable contact and durable operation in rear-window service.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268318781621,"sku":"BCRR-12X","price":25.41,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_12X_Fro.jpg?v=1775139787"},{"product_id":"valeo-13-windshield-wiper-blade","title":"Valeo 13 Windshield Wiper Blade - Front Left, Front Right or Rear","description":"\u003ch2\u003eValeo 13 Conventional Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Traditional 13 wiper blade is a conventional replacement built for steady wiping performance and a direct hook-style connection. It uses an OEM-informed design approach from Valeo, a brand known for supplying products used by major vehicle manufacturers and automotive professionals.\u003c\/p\u003e\u003cp\u003eUse this Valeo 13 blade when you need a conventional rear or front-right wiper blade for hook 9x3\/9x4 arms on vehicles such as the Honda CR-V, Toyota FJ Cruiser, and Jeep Wrangler.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e13-inch blade length for confirmed rear and front-right applications\u003c\/li\u003e\n\u003cli\u003eConventional blade design for straightforward OE-style replacement\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for consistent contact across the glass\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eT2 connector for Hook 9x3\/9x4 wiper arms\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Ultimate Traditional focuses on conventional wiper blade service where a simple, proven design is preferred. Part number 13 is built with a rubber wiping element and steel backbone to maintain blade shape and pressure during operation. This makes it a practical replacement for rear wiper service on vehicles like the Chevrolet Tahoe, GMC Yukon, and Cadillac Escalade, as well as front-right applications on select Toyota and Jeep models.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO 31-13 and TRICO 13-1 for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Solves\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking caused by a worn rubber wiping edge\u003c\/li\u003e\n\u003cli\u003eChatter from a blade that no longer tracks smoothly\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain, snow, or road spray\u003c\/li\u003e\n\u003cli\u003eUneven wiping from a weakened conventional frame\u003c\/li\u003e\n\u003cli\u003eFitment issues on Hook 9x3\/9x4 arm applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the arm style before ordering. This blade uses a T2 connector for Hook 9x3\/9x4 mounts and is listed for rear, front left, and front right positions depending on vehicle application. Match the 13-inch length to the original blade size and verify the position-specific fitment for your vehicle before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo builds the Ultimate Traditional line with OEM engineering principles and a conventional design trusted across a wide range of vehicle applications. Part number 13 is specified for confirmed fitment across 606 vehicle applications spanning 1957 through 2025.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268318879925,"sku":"BCRR-13","price":20.51,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_13_Fro_305a6df1-3924-487f-a720-a42994049770.jpg?v=1775139787"},{"product_id":"valeo-13v-windshield-wiper-blade","title":"Valeo 13V Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade for Rear Fitment\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade is a 13-inch beam-style rear blade built for consistent rear window cleaning and stable contact across the glass. It uses a V-Notch connector and steel backbone construction to support dependable wiping performance on select Volkswagen applications, including Volkswagen GTI, Jetta, Touareg, R32, and Tiguan Limited rear positions.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e13-inch rear wiper blade length\u003c\/li\u003e\n\u003cli\u003eBeam-style blade design for even pressure distribution\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for rear glass cleaning\u003c\/li\u003e\n\u003cli\u003eSteel backbone for structural support\u003c\/li\u003e\n\u003cli\u003eV-Notch connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eValeo Ultimate Rear product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo part number 13V is part of the Ultimate Rear line, a rear wiper blade family focused on OE-style engineering and application-specific design. This blade is built for rear wiper systems that use a V-Notch arm and a 13-inch blade length, making it a direct match for select Volkswagen rear applications. Compatible vehicle coverage includes Fits 2007-2014 Volkswagen GTI, Rear; Fits 2008-2014 Volkswagen Jetta, Rear; Fits 2004-2010 Volkswagen Touareg, Rear; Fits 2008 Volkswagen R32, Rear; and Fits 2017-2018 Volkswagen Tiguan Limited, Rear.\u003c\/p\u003e\u003cp\u003eThis part cross-references TRICO 13-G for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Blade Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped wiping caused by worn rubber\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eNoise from an aged or hardened blade edge\u003c\/li\u003e\n\u003cli\u003eUneven contact on a V-Notch rear wiper arm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the rear arm uses a V-Notch connector before installation. Match the 13-inch length to the existing rear blade and verify the blade seats fully on the arm hardware. After installation, test the rear washer and wiper sweep to confirm proper contact across the glass.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo applies OEM-focused engineering and design practices to this rear wiper blade line, with construction intended to support reliable everyday use on the listed Volkswagen rear applications. Part number 13V is built to the specified beam-style, V-Notch configuration for accurate fitment.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268318912693,"sku":"BCRR-13V","price":17.47,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_13V_Fro.jpg?v=1775139788"},{"product_id":"valeo-14-windshield-wiper-blade","title":"Valeo 14 Windshield Wiper Blade - Front Right or Rear","description":"\u003ch2\u003eValeo Ultimate Traditional 14 Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Traditional 14 wiper blade is a conventional replacement built for dependable wiping performance. It uses OEM-informed engineering and a steel backbone with a rubber wiping edge to deliver a direct-fit solution for vehicles that call for a 14-inch hook-style blade.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e14 in blade length for specified front right and rear applications\u003c\/li\u003e\n\u003cli\u003eConventional blade design for a traditional wiper arm setup\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for consistent windshield contact\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eConnector type: T2 hook 9x3\/9x4\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Ultimate Traditional line focuses on conventional replacement blades that match common OE-style mounting requirements. This Part Number 14 blade is designed for hook-arm applications and is listed for a wide range of vehicles, including the Honda Civic rear, Honda Fit front right, Toyota Corolla front right, and Nissan Versa front right. It is also used on select Hyundai Santa Fe, Kia Forte, and Chevrolet Spark applications where a 14-inch conventional blade is specified.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO 31-14 and TRICO 14-1 for the same application. The Valeo 14 wiper blade is also referenced across multiple OE and aftermarket numbers for direct replacement use.\u003c\/p\u003e\u003ch2\u003eWhat This Wiper Blade Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking caused by worn rubber wiping edges\u003c\/li\u003e\n\u003cli\u003eSkipping or chatter on the windshield\u003c\/li\u003e\n\u003cli\u003ePoor contact from an aging conventional blade\u003c\/li\u003e\n\u003cli\u003eReduced visibility in rain, sleet, or road spray\u003c\/li\u003e\n\u003cli\u003eReplacement needs for 14-inch hook-arm wiper applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Fitment Tips\u003c\/h2\u003e\u003cp\u003eFits 2016-2021 Chevrolet Spark, front right. Fits 2017-2021 Honda Civic, rear. Fits 2019-2021 Toyota Corolla, front right. Fits 2009-2020 Honda Fit, front right. Fits 2019-2020 Hyundai Santa Fe, front right. Fits 2011-2019 Fiat 500, front right. Fits 2013-2019 Hyundai Santa Fe XL, front right. Fits 2019 Nissan Versa, front right. Fits 2013-2018 Hyundai Santa Fe, front right. Fits 2013-2018 Hyundai Santa Fe Sport, front right. Fits 2014-2018 Kia Forte, front right. Fits 2014-2018 Kia Forte5, front right. Fits 2007-2018 Nissan Versa, front right. Fits 2012-2018 Toyota Prius C, front right. Fits 2016-2017 Hyundai Elantra GT, front right. Fits 2014-2017 Kia Forte Koup, front right. Fits 2011-2017 Nissan Juke, front right. Fits 2014-2016 Ford Transit Connect, rear. Fits 2011-2015 Hyundai Elantra, front right. Fits 2011-2015 Mazda 2, front right. Fits 2010-2015 Mitsubishi Lancer, rear. Fits 2008-2014 Scion xD, front right. Fits 2008-2013 Nissan Rogue, front right. Fits 1995-2005 GMC Jimmy, rear. Fits 1993-2005 GMC Safari, rear. Fits 1995-1999 Chevrolet C1500 Suburban, rear. Fits 1995-1999 Chevrolet C2500 Suburban, rear. Fits 1995-1999 Chevrolet K1500 Suburban, rear. Fits 1995-1999 Chevrolet K2500 Suburban, rear. Fits 1995-1999 Chevrolet Suburban 1500, rear. Fits 1995-1999 Chevrolet Tahoe, rear. Fits 1995-1999 GMC C1500 Suburban, rear. Fits 1995-1999 GMC C2500 Suburban, rear. Fits 1995-1999 GMC K1500 Suburban, rear. Fits 1995-1999 GMC K2500 Suburban, rear. Fits 1992-1999 GMC Yukon, rear. Fits 1989-1994 GMC Jimmy, rear. Fits 1992 Rolls-Royce Corniche II, front right.\u003c\/p\u003e\u003cp\u003eConfirm the arm style before installation. This blade uses a hook 9x3\/9x4 connector, so it should be matched to the vehicle’s existing wiper arm type and the required 14-inch length.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo is known for OEM engineering and supplies products used by major vehicle manufacturers and automotive professionals worldwide. The Ultimate Traditional line is built as a conventional replacement option for vehicles that specify this blade style and connector format.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268320223413,"sku":"BCRR-14","price":21.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14_Fro_edeeb53c-f1bc-42a4-8817-52d42034cbf4.jpg?v=1775139788"},{"product_id":"valeo-14a-windshield-wiper-blade","title":"Valeo 14A Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear 14A Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 14A is a 14-inch rear wiper blade built for vehicles that use a Roc Lock 2 or RL2 rear arm application. Its beam-style construction, rubber wiping edge, and steel backbone are engineered for consistent rear glass contact and clean visibility in everyday driving.\u003c\/p\u003e\u003cp\u003eValeo’s Ultimate Rear line focuses on OE-style engineering and application-specific design for rear wiper systems. This 14A blade is built for rear hatch and liftgate use on select Chrysler, Dodge, Hyundai, Jeep, Lexus, Mazda, Scion, and Toyota models, including applications such as the Mazda CX-5, Toyota Venza, and Chrysler Pacifica.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e14-inch rear wiper blade for select rear applications\u003c\/li\u003e\n\u003cli\u003eBeam style design for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear window performance\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eMounting hardware included for the listed application\u003c\/li\u003e\n\u003cli\u003ePart number: 14A\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eFitment Details\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 2023-2026 Dodge Hornet, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2021-2025 Chrysler Grand Caravan, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2025 Chrysler Pacifica, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2024-2025 Lexus RX450h+, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Hyundai Nexo, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Mazda CX-5, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2024 Toyota Venza, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022-2023 Jeep Cherokee, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022 Lexus RX450h, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2022 Toyota C-HR, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2017-2021 Chrysler Pacifica, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2019-2021 Hyundai Nexo, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2020-2021 Hyundai Tucson, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2014-2021 Jeep Cherokee, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2016-2021 Lexus RX450h, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2013-2021 Mazda CX-5, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2018-2021 Toyota C-HR, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2021 Toyota Venza, N\/A; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2020 Mazda CX-9, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2017-2019 Hyundai Tucson, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2019 Mazda CX-9, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2010-2015 Mazda 3, rear; with Roc Lock 2 Type Arm; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2008-2015 Scion xB, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Hyundai Santa Fe, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2012 Mazda CX-7, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2011 Hyundai Accent, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2009-2011 Kia Borrego, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Kia Rio, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2011 Kia Rio5, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2007-2010 Kia Rondo, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Kia Spectra, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Kia Spectra5, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2003-2009 Lexus GX470, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2006-2008 Lexus RX400h, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2008 Mitsubishi Endeavor, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004-2006 Lexus RX330, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2003-2006 Mitsubishi Outlander, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003cli\u003eFits 2004 Toyota Sienna, rear; Technology: BBI; Armtype: RL2; Blade Length: 14\"; Ultimate Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking or skipping on the rear window\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain, sleet, or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber that leaves water film behind\u003c\/li\u003e\n\u003cli\u003eUneven wiping caused by a fatigued blade structure\u003c\/li\u003e\n\u003cli\u003eFitment issues on rear arms using Roc Lock 2 or RL2 configurations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes\u003c\/h2\u003e\u003cp\u003eConfirm the rear arm style before ordering. This Valeo Ultimate Rear 14A blade is listed for Roc Lock 2 Type Arm and RL2 applications, with 14-inch rear fitments shown above. Match the vehicle year, make, model, and rear position exactly, then install the blade using the supplied mounting hardware for the specified application.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM-focused engineering with application-specific rear wiper design for major vehicle manufacturers and service professionals. The Ultimate Rear line is built to meet the demands of rear-window wiping on select Chrysler Pacifica, Mazda CX-5, Toyota Venza, and other compatible rear applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Bosch 18141 and TRICO 14-A for the same application.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268320616629,"sku":"BCRR-14A","price":17.13,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14A_Fro.jpg?v=1775139788"},{"product_id":"valeo-14b-windshield-wiper-blade","title":"Valeo 14B Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 14B\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade is a 14-inch rear beam-style blade built for consistent wiping performance and a clean OE-style fit. It is designed for rear applications on a wide range of vehicles, including Honda Pilot, Subaru Forester, Mazda 3, and Nissan LEAF models.\u003c\/p\u003e\u003cp\u003eValeo’s Ultimate Rear line focuses on OEM-inspired engineering and a composite beam design that helps maintain even pressure across the glass. Part number 14B is a direct-fit rear wiper blade for many vehicles that use a 14-inch rear blade profile.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e14-inch rear wiper blade for rear glass applications\u003c\/li\u003e\n\u003cli\u003eBeam-style construction for even contact across the wipe path\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear visibility\u003c\/li\u003e\n\u003cli\u003eSteel backbone for structural support\u003c\/li\u003e\n\u003cli\u003eBBI\/composite blade type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eOE-engineered design from Valeo Ultimate Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo 14B is a rear wiper blade engineered for vehicles that require a 14-inch rear blade, including many Honda, Mazda, Nissan, Subaru, Acura, INFINITI, Mitsubishi, Saab, and Isuzu applications. This part cross-references ANCO AR-14B and TRICO 14-B for the same application. If you are replacing a worn rear blade on a Honda Pilot, Subaru Forester, or Mazda CX-3, this Valeo rear blade provides the correct size and mounting style for listed fitments.\u003c\/p\u003e\u003cp\u003eThe Ultimate Rear product line is built around Valeo’s OEM-focused approach, combining a composite beam design with a steel backbone and rubber wiping element. That construction helps support steady rear-window contact and reliable wiping performance in everyday driving conditions.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear window\u003c\/li\u003e\n\u003cli\u003eSkipping or chatter during rear wiping\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn, cracked, or hardened rear wiper rubber\u003c\/li\u003e\n\u003cli\u003ePoor contact from an aging rear blade assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the rear arm style and blade length before installation. This part is listed for rear positions and also for select N\/A fitments where the vehicle uses the specified 14-inch rear blade configuration. Compare the existing connector and blade profile to the vehicle listing before removal, and make sure the blade seats securely on the rear arm after installation.\u003c\/p\u003e\u003cp\u003eCompatible With select rear applications on 2022-2025 Honda Pilot, 2022-2025 Subaru Forester, 2022-2025 Mazda 3, 2022-2025 Nissan LEAF, and other listed vehicles using a 14-inch rear blade. Fits 2003-2021 Honda Pilot, rear; Fits 2005-2019 Subaru Outback, rear; Fits 2003-2010 Nissan Murano, rear; Fits 2007-2018 Acura RDX, rear; Fits 2010-2015 Mitsubishi Lancer, rear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo is known for OEM engineering and supplies products trusted by major vehicle manufacturers, automotive professionals, and consumers worldwide. The Ultimate Rear line reflects that OE-focused design approach for rear wiper replacement applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268321009845,"sku":"BCRR-14B","price":17.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14B_Fro_ddea6fff-5eb4-4d31-8e89-2d9135227344.jpg?v=1775139789"},{"product_id":"valeo-14c-windshield-wiper-blade","title":"Valeo 14C Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade for Rear Fitments\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 14C is a beam-style rear wiper blade built for consistent wiping performance and a clean, OE-style fit. It uses a 14-inch rubber wiping edge, a steel backbone, and a Slide Pinch connector for the rear applications listed below.\u003c\/p\u003e\u003cp\u003eCompatible With rear wiper applications on Jeep Commander, Jeep Grand Cherokee, Chrysler Aspen, and Dodge Durango models from 2004 through 2010. The Valeo Ultimate Rear line focuses on advanced OEM engineering and a streamlined beam design for dependable rear window clearing.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003ePart number: 14C\u003c\/li\u003e\n\u003cli\u003eBlade length: 14 in\u003c\/li\u003e\n\u003cli\u003eBeam-style rear wiper blade\u003c\/li\u003e\n\u003cli\u003eRubber wiping element with BBI\/Composite blade type\u003c\/li\u003e\n\u003cli\u003eSteel backbone for blade support\u003c\/li\u003e\n\u003cli\u003eSlide Pinch connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003cli\u003eCross-reference: ANCO AR-14C and Bosch 18143\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 14C is engineered for rear-window service where a precise blade length and correct connector style matter. Its beam-style construction helps maintain even contact across the glass, while the rubber wiping edge is paired with a steel backbone for stable operation. This part number is commonly searched as Valeo 14C and is listed for rear applications on the Jeep Commander, Jeep Grand Cherokee, Chrysler Aspen, and Dodge Durango.\u003c\/p\u003e\u003cp\u003eFits 2006-2010 Jeep Commander, rear. Fits 2005-2010 Jeep Grand Cherokee, rear. Fits 2007-2009 Chrysler Aspen, rear. Fits 2004-2009 Dodge Durango, rear.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Blade Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipping or chatter during wipe cycles\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn or cracked rear wiper rubber\u003c\/li\u003e\n\u003cli\u003eIncorrect connector fit on the rear arm\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the rear arm uses a Slide Pinch connector before installation. Match the 14-inch blade length to the vehicle application and confirm the blade seats fully on the arm before operating the wiper system. If the rear glass is dirty or contaminated, clean it before testing the new blade to help prevent premature wear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo positions the Ultimate Rear line around OEM engineering and product design used by major vehicle manufacturers and automotive professionals. The 14C follows that approach with application-specific fitment, beam-style construction, and rear-wiper hardware details aligned to the listed vehicles.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268321140917,"sku":"BCRR-14C","price":18.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14C_Fro.jpg?v=1775139789"},{"product_id":"valeo-14e-windshield-wiper-blade","title":"Valeo 14E Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 14E\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 14E is a 14-inch rear wiper blade built in a beam-style design for consistent rear glass wiping performance. It uses a rubber wiping edge with a steel backbone and composite BBI construction to support steady contact and clean operation on the rear window.\u003c\/p\u003e\u003cp\u003eCompatible With rear applications on Ford Transit Connect, Volvo XC60, Ford Edge, Lincoln MKX, Nissan Versa, BMW X3, Mazda 3, Nissan Quest, Saab 9-7x, Jaguar X-Type, Saab 9-5, and Land Rover Discovery models listed below.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e14-inch rear wiper blade for listed rear applications\u003c\/li\u003e\n\u003cli\u003eBeam-style construction for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear rear window cleaning\u003c\/li\u003e\n\u003cli\u003eBBI\/composite blade type with steel backbone\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eOE-focused engineering from Valeo Ultimate Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo part number 14E is part of the Ultimate Rear line, a product line focused on rear wiper coverage with application-specific fitment. Valeo applies OEM-oriented engineering and design practices to deliver a rear blade that matches the needs of vehicles using a 14-inch Snap Claw BBI setup. This Valeo 14E rear wiper blade is listed for rear fitment on 2022-2023 Ford Transit Connect, 2010-2017 Volvo XC60, 2007-2014 Ford Edge, 2007-2015 Lincoln MKX, and additional rear applications across the fitment range.\u003c\/p\u003e\u003cp\u003eThis part cross-references TRICO 14-D for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear window\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wiping across the glass\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber that no longer clears water effectively\u003c\/li\u003e\n\u003cli\u003ePoor contact from an aging rear blade assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify the rear arm style before ordering; listed applications use Snap Claw mounting with BBI technology notes. Confirm the vehicle year, make, model, and rear position against the fitment list, including 14-inch blade length where specified. For best results, inspect the rear arm for wear or corrosion before installing the new blade and make sure the connector seats fully.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo designs the Ultimate Rear line with OEM engineering principles and application-specific rear fitment coverage. Part number 14E is built for the listed rear vehicle applications and uses a rubber wiping element with a steel backbone for consistent blade support.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eFits 2022-2023 Ford Transit Connect, rear\u003c\/li\u003e\n\u003cli\u003eFits 2017-2021 Ford Transit Connect, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2014-2015 Ford Transit Connect, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2010-2017 Volvo XC60, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2014-2016 Ford Transit Connect, rear; Armtype: Snap Claw; Technology: BBI; w\/ Plastic Arm; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2007-2015 Lincoln MKX, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 Ford Edge, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2007-2014 Nissan Versa, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2012-2014 Volvo XC90, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2004-2010 BMW X3, rear; E83; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2004-2009 Mazda 3, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2004-2009 Nissan Quest, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2005-2009 Saab 9-7x, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2007-2008 Isuzu Ascender, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2005-2008 Jaguar X-Type, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 2001-2008 Saab 9-5, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003cli\u003eFits 1999-2002 Land Rover Discovery, rear; Armtype: Snap Claw; Technology: BBI; Blade Length: 14\"\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268321239221,"sku":"BCRR-14E","price":17.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14E_Fro.jpg?v=1775139789"},{"product_id":"valeo-14hk-windshield-wiper-blade","title":"Valeo 14HK Windshield Wiper Blade - Front Right or Rear","description":"\u003ch2\u003eValeo Ultimate Beam Hook Wiper Blade 14HK\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Beam Hook wiper blade is a 14-inch beam-style replacement built for consistent wiping performance and a secure U-hook fit. Part number 14HK combines a steel backbone with a rubber wiping edge to support steady contact across the windshield and rear glass on select vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e14-inch beam wiper blade for front right and rear applications\u003c\/li\u003e\n\u003cli\u003eU (Hook 9x3\/9x4) connector type for common hook-style arms\u003c\/li\u003e\n\u003cli\u003eRubber blade material for clear wiping action\u003c\/li\u003e\n\u003cli\u003eSteel backbone for blade support and pressure distribution\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003cli\u003eValeo Ultimate Beam Hook product line for OE-focused replacement fitment\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo 14HK is part of the Ultimate Beam Hook line, a beam wiper blade family engineered with Valeo’s OEM-oriented design approach. The beam construction helps maintain even pressure along the glass, while the hook-style connector supports direct replacement on many import and domestic vehicles. This part number 14HK is listed for a wide range of applications, including Honda Civic, Toyota Corolla, and Hyundai Santa Fe models, along with several Nissan, Kia, and Chevrolet vehicles.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO C-14-UB and TRICO 16-140 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking caused by worn rubber wiping edges\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wipe patterns from weakened blade pressure\u003c\/li\u003e\n\u003cli\u003eReduced visibility in rain, sleet, and road spray\u003c\/li\u003e\n\u003cli\u003eFitment issues on U-hook 9x3 and 9x4 wiper arms\u003c\/li\u003e\n\u003cli\u003eNoise from aging conventional blade assemblies\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the arm style before installation: this blade uses a U-hook 9x3\/9x4 connector. Verify the required 14-inch length and match the position listed for your vehicle. Fits 2017-2021 Honda Civic, rear; Fits 2019-2021 Toyota Corolla, front right; Fits 2019-2020 Hyundai Santa Fe, front right; Fits 2009-2020 Honda Fit, front right; Fits 2007-2018 Nissan Versa, front right; Fits 2014-2018 Kia Forte, front right; Fits 2014-2016 Ford Transit Connect, rear.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo applies advanced OEM engineering and product design to this wiper blade line, with construction intended to support dependable performance for daily driving and routine replacement intervals.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268321730741,"sku":"BCRR-14HK","price":29.04,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14HK_Fro.jpg?v=1775139789"},{"product_id":"valeo-14t-windshield-wiper-blade","title":"Valeo 14T Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 14T\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear 14T is a rear wiper blade built with beam-style construction for consistent contact and long service life. It uses a rubber wiping edge, a steel backbone, and a Cross Pin connector for direct rear wiper arm applications on select BMW, Volvo, Ford, and Volkswagen models.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e14-inch rear wiper blade for select rear applications\u003c\/li\u003e\n\u003cli\u003eBeam-style design for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clean rear window clearing\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eCross Pin connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003cli\u003eValeo Ultimate Rear product line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo Ultimate Rear part number 14T is engineered for rear-window service where a precise beam blade is required. The beam design helps maintain steady wiping contact, while the rubber element is paired with a steel backbone for a balanced combination of flexibility and support. This Valeo 14T rear wiper blade is listed for applications such as BMW X5, Volvo XC90, Volvo XC60, Volvo XC40, Ford Edge, and Volkswagen Touareg with a Cross Pin type arm.\u003c\/p\u003e\u003cp\u003eThe Ultimate Rear line focuses on rear wiper applications that require OE-style fit and dependable wiping performance. For shoppers searching for a rear wiper blade for BMW X5 rear, Volvo XC90 rear wiper blade, or Ford Edge rear wiper blade, this part number 14T provides a direct-reference option for the listed vehicles and model years.\u003c\/p\u003e\u003cp\u003eThis part cross-references Bosch H281 and Trico R14C for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Part Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipping or chatter during rear wiping\u003c\/li\u003e\n\u003cli\u003ePoor rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eWorn or hardened rubber wiping edges\u003c\/li\u003e\n\u003cli\u003eLoose or incorrect rear blade fitment on Cross Pin arms\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm the rear arm uses a Cross Pin connector before installation.\u003c\/li\u003e\n\u003cli\u003eVerify blade length is 14 inches for the listed application.\u003c\/li\u003e\n\u003cli\u003eCheck the rear glass and arm condition before installing the new blade.\u003c\/li\u003e\n\u003cli\u003eFollow the vehicle-specific service procedure for removing and attaching the rear blade.\u003c\/li\u003e\n\u003cli\u003eAfter installation, test the blade on a wet rear window to confirm full contact and smooth operation.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM engineering practices with product design used across major vehicle manufacturer applications. The Ultimate Rear 14T is built to meet the fitment and construction requirements listed for the specified BMW, Volvo, Ford, and Volkswagen rear wiper applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268321960117,"sku":"BCRR-14T","price":18.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_14T_Fro_c1983ebe-7b49-450b-bf09-c37fceb7d3dd.jpg?v=1775139790"},{"product_id":"valeo-15-windshield-wiper-blade","title":"Valeo 15 Windshield Wiper Blade - Front Left, Front Right or Rear","description":"\u003ch2\u003eValeo Ultimate Traditional 15-Inch Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Traditional wiper blade is a conventional replacement built for dependable wiping performance. With a 15-inch rubber blade, steel backbone, and T2 hook connector, it serves drivers looking for a direct-fit conventional blade for rear or front-right applications on select vehicles.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e15 in. blade length for select rear and front-right applications\u003c\/li\u003e\n\u003cli\u003eConventional wiper blade design\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for consistent contact across the glass\u003c\/li\u003e\n\u003cli\u003eSteel backbone for stable blade support\u003c\/li\u003e\n\u003cli\u003eT2 connector type for Hook 9x3 \/ 9x4 arms\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Ultimate Traditional line focuses on conventional replacement blades that follow OEM-style engineering principles and practical design. This Valeo 15 part number is built for vehicles that use a hook-style arm or listed rear application, including select Mazda CX-50, Mazda CX-30, Nissan Sentra, Jeep Wrangler, and Mercedes-Benz G-Class models. It is also listed for many older rear and front-left applications where a 15-inch conventional blade is specified. This part cross-references ANCO 31-15 and TRICO 15-1 for the same application.\u003c\/p\u003e\u003cp\u003eCompatible fitment examples include Fits 2023-2025 Mazda CX-50, front right; Fits 2020 Mazda CX-30, front right; Fits 2013-2019 Nissan Sentra, front right; and Fits 2007-2017 Jeep Wrangler, front left or front right. The Valeo Ultimate Traditional 15 is also listed for rear applications on select Mercedes-Benz G500, G550, and G63 AMG models.\u003c\/p\u003e\u003ch2\u003eCommon Problems This Blade Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking caused by worn rubber wiping edges\u003c\/li\u003e\n\u003cli\u003eChatter or skipping across the windshield\u003c\/li\u003e\n\u003cli\u003ePoor glass contact from a fatigued conventional frame\u003c\/li\u003e\n\u003cli\u003eReduced rear visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eFitment issues when replacing a hook-style 15-inch blade\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the arm style before ordering. This blade uses a T2 connector for Hook 9x3 \/ 9x4 arms, and fitment varies by position, including front right, front left, and rear applications. Match the vehicle position and blade length exactly to the catalog listing, especially on vehicles such as the Jeep Wrangler, Mazda CX-30, and Nissan Sentra. If replacing a rear blade, verify that the arm type matches the listed application before installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM-focused engineering with conventional blade construction to support consistent replacement performance. The Ultimate Traditional line is positioned as a practical replacement option trusted across a wide range of vehicle applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268323205301,"sku":"BCRR-15","price":21.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_15_Fro_23c7a40f-ed47-48f6-8f41-d47c090329f7.jpg?v=1775139790"},{"product_id":"valeo-15hk-windshield-wiper-blade","title":"Valeo 15HK Windshield Wiper Blade - Front Left, Front Right or Rear","description":"\u003ch2\u003eValeo Ultimate Beam Hook Wiper Blade 15HK\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Beam Hook 15HK is a 15-inch beam wiper blade built for consistent wiping performance and a secure U-hook fitment. It combines Valeo OEM engineering with a steel backbone and rubber wiping edge for dependable contact across the windshield.\u003c\/p\u003e\u003cp\u003eCompatible With a wide range of vehicles, including the 2023-2025 Mazda CX-50 front right, 2020 Mazda CX-30 front right, and 2013-2019 Nissan Sentra front right. The 15HK also fits many rear applications such as Jeep Wrangler, Mercedes-Benz G-Class models, and Audi, Subaru, Ford, Honda, and Volkswagen rear wiper positions.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e15-inch beam-style wiper blade\u003c\/li\u003e\n\u003cli\u003eU-hook connector type: 9x3\/9x4\u003c\/li\u003e\n\u003cli\u003eRubber wiping element for clear, even contact\u003c\/li\u003e\n\u003cli\u003eSteel backbone for blade stability\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eOE-focused design from Valeo Ultimate Beam Hook\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo designed the Ultimate Beam Hook line for drivers who need a direct-fit beam blade with broad vehicle coverage and OE-style engineering. The beam construction helps maintain even pressure along the glass, while the rubber blade material is selected for steady wiping action in everyday driving and wet-weather use. The 15HK part number is used across front right and rear applications, including Mazda CX-50, Mazda CX-30, and Nissan Sentra fitments, as well as many Jeep Wrangler and Mercedes-Benz G-Class rear positions.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO C-15-UB and Mopar 68002390AA for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Problems It Can Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking across the windshield\u003c\/li\u003e\n\u003cli\u003eChattering or skipping during operation\u003c\/li\u003e\n\u003cli\u003ePoor glass contact from worn blade edges\u003c\/li\u003e\n\u003cli\u003eReduced visibility in rain or road spray\u003c\/li\u003e\n\u003cli\u003eNoise caused by an aging wiper blade assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eConfirm the vehicle uses a U-hook 9x3\/9x4 arm before installation.\u003c\/li\u003e\n\u003cli\u003eVerify the required position, since this blade is listed for front right, front left, and rear applications depending on vehicle.\u003c\/li\u003e\n\u003cli\u003eInspect the wiper arm for wear or damage before installing the new blade.\u003c\/li\u003e\n\u003cli\u003eClean the windshield glass before first use to help the rubber edge seat properly.\u003c\/li\u003e\n\u003cli\u003eCheck blade sweep after installation to confirm full contact and proper clearance.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo backs this blade with advanced OEM engineering and product design used by major vehicle manufacturers and automotive professionals worldwide. The Ultimate Beam Hook line is built to deliver reliable fitment and consistent wiping performance across its listed applications.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268323631285,"sku":"BCRR-15HK","price":29.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_15HK_Fro_c279013b-998c-4acd-b39d-b797b285ed8e.jpg?v=1775139790"},{"product_id":"valeo-15oe-windshield-wiper-blade","title":"Valeo 15OE Windshield Wiper Blade - Front Right","description":"\u003ch2\u003eValeo Ultimate Beam Original Wiper Blade\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Beam Original is a 15-inch beam wiper blade built for consistent windshield contact and lasting performance. It uses OEM-focused engineering and a streamlined beam design to deliver dependable wiping on select Fiat, Chevrolet, and Pontiac front-right applications.\u003c\/p\u003e\u003cp\u003eFor shoppers searching for a 15 inch beam wiper blade for Fiat 500X, Fiat 500L, Chevrolet Sonic, Chevrolet SS, or Pontiac G8 front right, the Valeo 15OE is a direct-fit option with the correct MA (Pinch Tab) connector.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e15 in blade length for the specified front-right applications\u003c\/li\u003e\n\u003cli\u003eBeam-style design for even pressure across the windshield\u003c\/li\u003e\n\u003cli\u003eRubber wiping edge for clear, consistent wipe performance\u003c\/li\u003e\n\u003cli\u003eSteel backbone for structural support\u003c\/li\u003e\n\u003cli\u003eMA (Pinch Tab) connector type\u003c\/li\u003e\n\u003cli\u003eMounting hardware included: Yes\u003c\/li\u003e\n\u003cli\u003eOE-focused design from Valeo’s Ultimate Beam Original line\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Beam Original line is built around OEM engineering and application-specific design. This part number, 15OE, is a beam wiper blade made for vehicles that require a 15-inch front-right blade with a MA (Pinch Tab) connection. It is listed for 2024-2025 Fiat 500E front right, 2021-2023 Fiat 500X front right, 2014-2020 Fiat 500L front right, 2016-2020 Fiat 500X front right, 2012-2019 Chevrolet Sonic front right, 2014-2015 Chevrolet SS front right, and 2008-2009 Pontiac G8 front right.\u003c\/p\u003e\u003cp\u003eThis part cross-references ANCO C-15-OE and TRICO 15-15B for the same application. If you are replacing a worn front-right blade on a Fiat 500X, Fiat 500L, or Chevrolet Sonic, the Valeo 15OE provides the correct beam-style fitment and connector style for those listed vehicles.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking caused by a worn rubber wiping edge\u003c\/li\u003e\n\u003cli\u003eChatter from uneven blade pressure\u003c\/li\u003e\n\u003cli\u003ePoor windshield contact on a beam-style application\u003c\/li\u003e\n\u003cli\u003eFitment issues from using the wrong connector type\u003c\/li\u003e\n\u003cli\u003eReduced wiping performance on the front-right side\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm the vehicle year, make, model, and front-right position before installation. Verify that the existing arm uses an MA (Pinch Tab) connector and that the blade length matches the 15-inch specification. Compare the old blade’s attachment style and seating points before locking the new blade into place.\u003c\/p\u003e\u003cp\u003eFor vehicles such as the Fiat 500E, Fiat 500X, and Chevrolet Sonic, proper alignment on the front-right arm helps ensure smooth operation and full windshield coverage. Always check that the blade is fully secured after installation.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo is known for OEM-oriented wiper engineering and supplies products trusted by vehicle manufacturers and automotive professionals worldwide. The Ultimate Beam Original line reflects that application-specific approach, with a beam construction designed for reliable everyday use on the listed fitments.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268323696821,"sku":"BCRR-15OE","price":20.57,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_15OE_Fro.jpg?v=1775139791"},{"product_id":"valeo-16a-windshield-wiper-blade","title":"Valeo 16A Windshield Wiper Blade - Rear","description":"\u003ch2\u003eValeo Ultimate Rear Wiper Blade 16A\u003c\/h2\u003e\u003cp\u003eThe Valeo Ultimate Rear wiper blade is a 16-inch beam-style rear blade built for consistent wiping performance and a clean rear window. It uses a rubber wiping edge, a steel backbone, and composite BBI construction to support stable contact across the glass.\u003c\/p\u003e\u003cp\u003eDesigned for rear applications on select Lexus RX350, Lexus RX450h, Lexus RX500h, Toyota Prius, Toyota Prius Plug-In, and Toyota Sienna models, the 16A is a direct-fit rear wiper blade for vehicles using the Roc Lock 2 or RL2 arm type.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003e16-inch rear wiper blade length\u003c\/li\u003e\n\u003cli\u003eBeam-style design for even pressure across the glass\u003c\/li\u003e\n\u003cli\u003eRubber blade material for rear window wiping\u003c\/li\u003e\n\u003cli\u003eBBI\/composite blade construction with steel backbone\u003c\/li\u003e\n\u003cli\u003eMounting hardware included\u003c\/li\u003e\n\u003cli\u003eEngineered with OEM-focused design practices\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Details\u003c\/h2\u003e\u003cp\u003eValeo’s Ultimate Rear line focuses on rear wiper applications where precise fit and steady wiping action matter. This part number 16A is built for rear use on vehicles such as the Toyota Prius, Toyota Sienna, and Lexus RX350, with fitment that includes 2004-2021 Toyota Prius rear applications, 2010-2021 Lexus RX350 rear applications, and 2011-2019 Toyota Sienna rear applications. It also covers select Lexus RX450h, Prius Plug-In, RX500h, and 2022 Toyota Prius and Lexus RX350 rear configurations with Roc Lock 2 type arms.\u003c\/p\u003e\u003cp\u003eThis part cross-references Bosch 18161 for the same application.\u003c\/p\u003e\u003ch2\u003eWhat It Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eStreaking on the rear glass\u003c\/li\u003e\n\u003cli\u003eSkipped or uneven wiping across the rear window\u003c\/li\u003e\n\u003cli\u003eReduced visibility in rain, snow, or road spray\u003c\/li\u003e\n\u003cli\u003eWorn rubber that no longer clears the glass cleanly\u003c\/li\u003e\n\u003cli\u003ePoor rear wiper contact caused by an aging blade assembly\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eConfirm rear arm style before installation, especially on vehicles using Roc Lock 2 or RL2 configurations. Match the 16-inch blade length to the original rear application and verify the connector seats fully on the arm. After installation, test the blade on a clean rear window to confirm smooth travel and even contact.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eValeo combines OEM engineering practices with product design used by major vehicle manufacturers and automotive professionals worldwide. The Ultimate Rear line is built to deliver dependable rear wiping performance in the applications listed above.\u003c\/p\u003e","brand":"Valeo","offers":[{"title":"Default Title","offer_id":45268324024501,"sku":"BCRR-16A","price":21.81,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/V3_16A_Fro.jpg?v=1775139791"}],"url":"https:\/\/www.partcatalog.com\/collections\/valeo\/fog-light.oembed","provider":"PartCatalog","version":"1.0","type":"link"}