{"product_id":"cardone-78-1286f-engine-control-module-ecm","title":"Cardone 78-1286F Engine Control Module (ECM)","description":"\u003ch2\u003eRemanufactured ECM for Ford and Lincoln\u003c\/h2\u003e\u003cp\u003eThe Cardone 78-1286F remanufactured engine control module is built for direct replacement in select Ford and Lincoln applications. It is flash programmable, computer tested, and remanufactured to restore engine management functions in vehicles such as the Ford Explorer, Ford Flex, and Lincoln MKT.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eRemanufactured engine control module for standard replacement use\u003c\/li\u003e\n\u003cli\u003eFlash programming required; flashable for application-specific setup\u003c\/li\u003e\n\u003cli\u003e3 connectors with 190 male terminals and pin-style terminals\u003c\/li\u003e\n\u003cli\u003eFemale connector design with rectangle and square connector shapes\u003c\/li\u003e\n\u003cli\u003eCritical components are re-soldered or replaced during remanufacturing\u003c\/li\u003e\n\u003cli\u003e100% computer tested for reliability before release\u003c\/li\u003e\n\u003cli\u003ePackage includes the module and instruction sheet\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eProduct Line Details\u003c\/h2\u003e\u003cp\u003eCardone’s Remanufactured Engine Control Module line focuses on correcting common failure points found in original electronic and powertrain control units. The remanufacturing process uses reverse engineering to identify design weaknesses, then replaces or re-solders critical circuit-board components at the Philadelphia manufacturing plant. This approach supports consistent operation in electronically controlled Ford Explorer, Ford Flex, and Lincoln MKT applications.\u003c\/p\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003ePart number 78-1286F is a remanufactured ECM designed to meet or exceed original equipment performance targets. It is built around a circuit board assembly with three connectors, a pin terminal layout, and a standard replacement grade. Because flash programming is required, the module must be programmed to the vehicle’s calibration after installation. This ECM is listed for 2013-2015 Ford Explorer and 2014-2019 Ford Flex and Lincoln MKT applications.\u003c\/p\u003e\u003cp\u003eThis part cross-references Ford service numbers such as DB5A12A650AEA and DB5Z12A650HJ for the same application.\u003c\/p\u003e\u003ch2\u003eCommon Issues Addressed\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eCheck engine light remains on after reset\u003c\/li\u003e\n\u003cli\u003eEngine shuts off unexpectedly\u003c\/li\u003e\n\u003cli\u003eLoss of spark or fuel injection control\u003c\/li\u003e\n\u003cli\u003eFuel pump pulse loss\u003c\/li\u003e\n\u003cli\u003eIntermittent starting problems\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eVerify the original failure cause before replacing the ECM; inspect grounds, power supply, wiring harness condition, and relay or solenoid shorts.\u003c\/li\u003e\n\u003cli\u003eFlash programming is required after installation.\u003c\/li\u003e\n\u003cli\u003eSome GM and Ford anti-theft systems may require module transfer or reset procedures depending on the vehicle.\u003c\/li\u003e\n\u003cli\u003eChrysler models 1996 and newer require VIN programming, but this part should be matched to the correct application before installation.\u003c\/li\u003e\n\u003cli\u003eFollow the OEM service manual for programming, anti-theft relearn, and calibration steps.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eCardone remanufactures this ECM to restore dependable electronic control performance using tested components and validated assembly procedures. Each unit is computer tested to confirm operation before it leaves the manufacturing plant.\u003c\/p\u003e","brand":"Cardone","offers":[{"title":"Default Title","offer_id":52887495377077,"sku":"CPCX-78-1286F","price":639.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/A1_781286F_Fro.jpg?v=1785393235","url":"https:\/\/www.partcatalog.com\/products\/cardone-78-1286f-engine-control-module-ecm","provider":"PartCatalog","version":"1.0","type":"link"}