{"product_id":"inmotion-ws1180-wheel-seal-front-inner-or-rear","title":"InMotion WS1180 Wheel Seal - Front, Inner or Rear","description":"\u003ch2\u003eWheel Seal for Differential Pinion Applications\u003c\/h2\u003e\u003cp\u003eThe InMotion WS1180 wheel seal is built for differential pinion sealing where a precise barrier against dirt, moisture, and lubricant loss matters. Made from nitrile and sized to 41 x 55 x 7 mm, it supports a secure seal at the housing bore and shaft interface for consistent driveline protection.\u003c\/p\u003e\u003ch2\u003eKey Features\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eNitrile seal material for dependable sealing performance\u003c\/li\u003e\n\u003cli\u003eExternal markings: 41 x 55 x 7\u003c\/li\u003e\n\u003cli\u003eInside diameter: 1.56 in \/ 39.6 mm\u003c\/li\u003e\n\u003cli\u003eOutside diameter: 2.17 in \/ 55.2 mm\u003c\/li\u003e\n\u003cli\u003eWidth: 0.276 in \/ 7 mm\u003c\/li\u003e\n\u003cli\u003eHousing bore: 2.165 in \/ 55 mm\u003c\/li\u003e\n\u003cli\u003eShaft diameter: 1.614 in \/ 41 mm\u003c\/li\u003e\n\u003cli\u003eSeal case material: JIS G3521\u003c\/li\u003e\n\u003cli\u003eSpring material: JIS G3141\u003c\/li\u003e\n\u003cli\u003ePart number WS1180 for catalog and service matching\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eDetailed Description\u003c\/h2\u003e\u003cp\u003eInMotion WS1180 is a precision-engineered seal for differential pinion service, helping maintain a tight seal around the rotating shaft while keeping contaminants out of the internal assembly. Its nitrile construction and measured dimensions make it a practical replacement for vehicles that require a 41 mm shaft diameter, 55 mm housing bore, and 7 mm width. This part number WS1180 is listed for applications including Acura RL, Acura TL, Acura Legend, Toyota Corolla, Toyota MR2, Toyota Tercel, Geo Prizm, and Chevrolet Nova in the positions shown below.\u003c\/p\u003e\u003cp\u003eThis part cross-references Monroe Shocks \u0026amp; Struts (e.g., 172286, 182286) for the same application.\u003c\/p\u003e\u003ch2\u003eCompatible Vehicle Applications\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eFits 1996-2001 Acura RL, Inner\u003c\/li\u003e\n\u003cli\u003eFits 1996-1998 Acura TL, Inner\u003c\/li\u003e\n\u003cli\u003eFits 1991-1995 Acura Legend, Inner\u003c\/li\u003e\n\u003cli\u003eFits 1989-1992 Geo Prizm, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1984-1992 Toyota Corolla, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1985-1989 Toyota MR2, Front\u003c\/li\u003e\n\u003cli\u003eFits 1985-1988 Chevrolet Nova, Rear\u003c\/li\u003e\n\u003cli\u003eFits 1984-1987 Toyota Tercel, Rear\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eWhat This Seal Helps Address\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003eDifferential pinion oil seepage at the seal surface\u003c\/li\u003e\n\u003cli\u003eContamination from road debris and moisture entering the assembly\u003c\/li\u003e\n\u003cli\u003eWear caused by degraded sealing material\u003c\/li\u003e\n\u003cli\u003eLoss of internal lubricant that can affect driveline operation\u003c\/li\u003e\n\u003cli\u003eService issues on Acura RL, Acura TL, Acura Legend, Toyota Corolla, Toyota MR2, Toyota Tercel, Geo Prizm, and Chevrolet Nova applications\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch2\u003eInstallation Notes and Tips\u003c\/h2\u003e\u003cp\u003eVerify shaft diameter, housing bore, and width before installation to confirm the WS1180 matches the original seal dimensions. Inspect the sealing surface for scoring or corrosion, and clean the bore thoroughly before pressing the new seal into place. For best results, install the seal squarely to avoid distortion and ensure even contact around the pinion shaft.\u003c\/p\u003e\u003ch2\u003eQuality Assurance\u003c\/h2\u003e\u003cp\u003eInMotion manufactures this seal with specified material and dimensional standards to support consistent fit and sealing performance in driveline service.\u003c\/p\u003e","brand":"InMotion","offers":[{"title":"Default Title","offer_id":52409521995957,"sku":"HKKS-WS1180","price":6.98,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0628\/1442\/1173\/files\/WJ_WS1180_Fro2.jpg?v=1777783402","url":"https:\/\/www.partcatalog.com\/products\/inmotion-ws1180-wheel-seal-front-inner-or-rear","provider":"PartCatalog","version":"1.0","type":"link"}