/live/media/A1/A1_1G6001_Fro.jpg)
Cardone 1G-6001 Rack and Pinion Assembly
| Brand | Cardone 1G-6001 |
|---|---|
| Type | Manual |
| Mounting Hardware Included | No |
| Grade Type | Regular |
| Gasket Or Seal Included | No |
| Mounting Hole Quantity | 2 |
| Mounting Brackets Included | No |
| Bellows Color | Black |
| Outer Tie Rods Included | No |
| End To End Length | 1231.41 |
| End To End Length | 48.50 |
| Total Turns Lock To Lock | 3.50 |
| Steering Input Shaft Spline Quantity | 36 |
| Steering Input Shaft Diameter | 18.97 |
| Inner Tie Rods Included | Yes |
| Does it require SDS | No |
| FAA_A1 | Rubber seals, dust boots, wear items, lubricant(s), clamps and be |
| FAA_A2 | Yes, all units produced are verified to function to o.e. design s |
| FAA_A3 | Yes, the steering wheel must be held in a straight-ahead position |
| FAA_A4 | Yes, these systems are equipped with torque angle sensors in the |
| FAA_A5 | Not recommended; radical modifications would be needed for instal |
| Input Shaft Type | Bolt groove |
| Is Item A Chemical | No |
| Is Or Contains A Battery | No |
| Is Or Contains A Bulb | No |
| Is the item CARB affected | No |
| Product line | Remanufactured Rack and Pinion Assembly |
| Fits | Mitsubishi · 17 vehicles |
Remanufactured assembly. Restored to rigorous quality and performance standards for dependable steering operation.
Factory-tested. Verified under extreme conditions and checked for proper on-car communication.
New sealing components. Rubber seals, dust boots, and lubricant are replaced to help extend service life.
Cross-references 4410A498 for the same application. See all 1.
Remanufactured Steering Rack for Mirage
Cardone 1G-6001 is a remanufactured manual rack and pinion assembly built for Mitsubishi Mirage and Mirage G4 applications. It is restored with new premium components, replaced rubber sealing parts, and specialized lubricant to support long service life and consistent steering feel.
Key Features
- Remanufactured manual rack and pinion assembly
- Fits 2014-2023 Mitsubishi Mirage and 2017-2023 Mitsubishi Mirage G4
- Inner tie rods included; outer tie rods not included
- Black bellows, 2 mounting holes, 3.50 turns lock-to-lock
- 36-spline steering input shaft with bolt groove input shaft type
- Package contents: rack and pinion assembly and instruction sheet
- Cardone part number 1G-6001 for direct catalog lookup
Product Details
This Cardone Remanufactured Rack and Pinion Assembly is engineered for manual steering systems and restored to rigorous performance standards. Each unit is factory tested to verify operation against original equipment design expectations, with attention to on-car communication where applicable. The remanufacturing process replaces rubber seals, dust boots, wear items, clamps, bearings, and lubricant to help maintain steering precision and durability. For Mitsubishi Mirage and Mitsubishi Mirage G4 owners, 1G-6001 provides a direct replacement option for worn steering gear assemblies.
This part cross-references 4410A498 for the same application.
Common Problems This Part Can Address
- Excessive steering play or loose steering response
- Fluid-related wear at the rack seals and boots
- Uneven steering effort caused by internal rack wear
- Noise or binding from a worn steering gear assembly
- Restoring steering control on a high-mileage Mitsubishi Mirage or Mirage G4
Installation Notes
Before removing the intermediate shaft, hold the steering wheel in the straight-ahead position to prevent clock spring damage. If the shaft rotates, the clock spring must be removed and re-centered. Vehicles with torque angle sensors in the steering column require recalibration after installation. Mounting hardware, mounting brackets, gasket or seal, and outer tie rods are not included. Verify the vehicle uses the correct manual steering configuration before installation.
Quality Assurance
Cardone remanufactures this rack and pinion assembly with new premium components and replaces sealing and wear items to support durability. Each unit is verified against OE design specifications and tested under simulated operating conditions through Cardone’s Factory Test Drive process. Cardone 1G-6001 is built for 2014-2023 Mitsubishi Mirage and 2017-2023 Mitsubishi Mirage G4 applications.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 2023 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2023 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2022 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2022 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2021 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2021 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2020 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2020 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2019 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2019 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2018 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2018 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2017 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2017 | Mitsubishi | Mirage G4 | N/A | Remanufactured Rack and Pinion Assembly |
| 2016 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2015 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| 2014 | Mitsubishi | Mirage | N/A | Remanufactured Rack and Pinion Assembly |
| No rows match your filter. | ||||