/live/media/A1/A1_221040_Fro.jpg)
Cardone 22-1040 Rack and Pinion Assembly
| Brand | Cardone 22-1040 |
|---|---|
| Casting Material | Steel; Aluminum |
| Distance Between Mounting Holes (in) | 2.88 |
| Distance Between Mounting Holes (mm) | 73.03 |
| E-Waste | No |
| Hose Port Type | O-Ring |
| Input Shaft Diameter (in) | 0.75 |
| Input Shaft Diameter (mm) | 19.05 |
| Input Shaft Length (in) | 1.88 |
| Input Shaft Length (mm) | 47.63 |
| Number of Mounting Holes | 3 |
| Package Contents | Rack and Pinion, Rubber Bushing, Sealing Kit, Instruction Sheet |
| Pressure Port ID Size | 0.472 |
| Product Condition | Remanufactured |
| Rack Length (in) | 48.88 |
| Rack Length (mm) | 1241.43 |
| Return Port ID Size | 0.436 |
| Steering Rack Color | Black |
| Thread Length (in) | 2.28 |
| Thread Length (mm) | 57.81 |
| Tie Rod Ends Included | Yes |
| Total Turns Lock to Lock | 3.25 |
| Product line | Rack and Pinion Assembly |
| Fits | Hummer · 6 vehicles |
Remanufactured OE part. Built to original equipment standards for a precise fit and dependable performance.
Factory-tested. Each unit is driven under extreme conditions to verify operation and communications.
New sealing components. Fresh seals and specialized lubricant help reduce leaks and extend service life.
Cross-references Hummer 15234374, Hummer 15864176 and Hummer 25817577 for the same application. See all 5.
Cardone Electronic Power Steering Rack
Restore steering response with this remanufactured Cardone rack and pinion assembly, part number 22-1040. Built for the Hummer H3 and H3T applications listed below, it combines OE-style fitment with new sealing components and a factory test drive process for verified operation.
Key Features
- Remanufactured rack and pinion assembly for electronic power steering applications
- New spool valve seals and rack donut seals installed to reduce internal leakage
- Specialized lubricant applied for extended service life
- Protective black finish helps resist corrosion and rust
- Steel and aluminum construction with O-ring hose ports
- Includes rack and pinion, rubber bushing, sealing kit, and instruction sheet
- Tie rod ends included
Product Details
Cardone 22-1040 is an expertly remanufactured steering rack built to original equipment dimensions for a precise vehicle fit. The unit is factory tested under simulated driving conditions and checked for on-car communications, helping confirm proper electronic power steering operation before installation. This rack and pinion assembly uses a 48.88-inch rack length, 3 mounting holes, and a 3.25 total turns lock-to-lock specification for the listed Hummer H3 and H3T models.
This part cross-references Hummer OE numbers 15234374 and 15864176 for the same application. It is a direct-fit steering solution for 2006-2010 Hummer H3 and 2010 Hummer H3T applications, including 2006-2008 Hummer H3 models with 16 mm diameter tie rods and hydraulic power steering.
Common Steering Issues It Can Address
- Hard steering during the first few minutes of driving
- Internal fluid bypass from worn rack seals
- Steering that does not return to center after a turn
- Power steering pump whine caused by air in the system after service
- Excessive play or inconsistent steering feel
Installation Notes
For 2009-2010 Hummer H3 and 2010 Hummer H3T applications, install an in-line filter, use OE fluid, and flush the hydraulic power steering system when installing the rack and pinion assembly with inner tie rods for warranty validation. For 2006-2008 Hummer H3 applications, follow the listed note for 16 mm diameter tie rods, hydraulic power steering, and in-line filter use. Bleed the steering system completely after installation to remove trapped air.
Quality Assurance
Cardone remanufactures this rack and pinion assembly to rigorous quality and performance standards using brand-new premium components where applicable. The process replaces all rubber sealing components, applies a specialized lubricant, and uses a factory test drive to verify operation under demanding conditions. The remanufacturing process also reduces energy and raw material use compared with producing a new part.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 2010 | Hummer | H3 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2010 | Hummer | H3T | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2009 | Hummer | H3 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2008 | Hummer | H3 | N/A | with 16 mm Diameter Tie Rod; Includes Inner Tie Rods; In-Line Filter available; For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system; with Hydraulic Power; Rack and Pinion Assembly |
| 2007 | Hummer | H3 | N/A | with 16 mm Diameter Tie Rod; Includes Inner Tie Rods; In-Line Filter available; For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system; with Hydraulic Power; Rack and Pinion Assembly |
| 2006 | Hummer | H3 | N/A | with 16 mm Diameter Tie Rod; Includes Inner Tie Rods; In-Line Filter available; For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system; with Hydraulic Power; Rack and Pinion Assembly |
| No rows match your filter. | ||||