/live/media/A1/A1_221107_Fro.jpg)
Cardone 22-1107 Rack and Pinion Assembly
| Brand | Cardone 22-1107 |
|---|---|
| Casting Material | Steel; Aluminum |
| Distance Between Mounting Holes (in) | 3.75 |
| Distance Between Mounting Holes (mm) | 95.25 |
| E-Waste | No |
| Hose Port Type | O-Ring |
| Input Shaft Diameter (in) | 0.75 |
| Input Shaft Diameter (mm) | 18.95 |
| Input Shaft Length (in) | 5.786 |
| Input Shaft Length (mm) | 146.96 |
| Number of Mounting Holes | 3 |
| Package Contents | Rack and Pinion, Sealing Kit, Instruction Sheet |
| Pressure Port Thread Size | M18 x 1.5 |
| Product Condition | Remanufactured |
| Rack Length (in) | 52.94 |
| Rack Length (mm) | 1344.63 |
| Return Port Thread Size | M16 x 1.5 |
| Steering Rack Color | Black |
| Thread Length (in) | 2.14 |
| Thread Length (mm) | 54.28 |
| Tie Rod Ends Included | Yes |
| Total Turns Lock to Lock | 2.63 |
| Product line | Rack and Pinion Assembly |
| Fits | Chevrolet · 6 vehicles |
Remanufactured OE part. Built to original equipment standards for a precise replacement fit.
Factory-tested. Simulates extreme operating conditions and verifies on-car communications.
New sealing components. Fresh rubber seals and specialized lubricant help extend service life.
Cross-references Chevrolet 20978657, Chevrolet 22930456 and Chevrolet 92241184 for the same application. See all 4.
Remanufactured Steering Rack for Camaro
CARDONE 22-1107 is a remanufactured electronic power steering rack and pinion assembly built for direct replacement on select Chevrolet Camaro applications. It is engineered with new premium components, updated sealing parts, and a protective finish to support dependable steering response and long service life.
Key Features
- Remanufactured Original Equipment-style rack and pinion assembly for proper vehicle fit
- Fits Chevrolet Camaro applications with hydraulic power assist
- New spool valve seals and rack donut seals installed where applicable
- 100% replacement of rubber sealing components
- Specialized lubricant applied during remanufacturing for extended service life
- Factory test driven to verify operation under demanding conditions and confirm on-car communications
- Protective coating helps resist corrosion and rust
- Includes rack and pinion, sealing kit, and instruction sheet
Detailed Description
This CARDONE Rack and Pinion Assembly, part number 22-1107, is remanufactured to meet rigorous quality and performance standards for steering repair. It uses steel and aluminum construction, a black finish, O-ring hose ports, and tie rod ends included in the assembly. The unit measures 52.94 inches in rack length, has a 0.75-inch input shaft diameter, 5.786-inch input shaft length, and 2.63 total turns lock to lock. It also features M18 x 1.5 pressure port threads and M16 x 1.5 return port threads for the listed applications.
Compatible With 2010-2011 Chevrolet Camaro and 2014-2015 Chevrolet Camaro, this steering rack is a direct-fit replacement for vehicles in the confirmed fitment range. CARDONE 22-1107 is also referenced by Chevrolet part numbers 20978657, 22930456, 92241184, and 92244725 for the same application.
Common Issues This Part May Address
- Hard steering during the first few minutes of driving
- Internal fluid bypass or steering assist loss
- Steering that does not return to center after a turn
- Power steering pump whine caused by air in the system after repair
- Leaks from worn rack seals or spool valve seals
Installation Notes and Tips
- Fits 2010-2011 Chevrolet Camaro, N/A
- Fits 2012-2013 Chevrolet Camaro, N/A; with Hydraulic Power Assist; Includes Inner Tie Rods; In-Line Filter available; for warranty purposes, install a filter, use the suggested OE fluid, and flush the system
- Fits 2014-2015 Chevrolet Camaro, N/A
- Install an in-line filter and use OE fluid where specified
- Flush the hydraulic power steering system during installation
- Bleed the steering system completely to remove air and reduce pump noise
- Check front-end alignment and return-line condition if steering does not self-center
Quality Assurance
CARDONE remanufactures this rack and pinion assembly using a process that replaces worn rubber sealing components, applies specialized lubricant, and verifies operation through factory test driving. The remanufacturing process also reduces energy and raw material use compared with producing a new part.
| Year | Make | Model | Liters | Cylinders | Position | Notes |
|---|---|---|---|---|---|---|
| 2015 | Chevrolet | Camaro | 3.6L | V6 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2014 | Chevrolet | Camaro | 3.6L | V6 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2013 | Chevrolet | Camaro | — | — | N/A | with Hydraulic Power Assist; Includes Inner Tie Rods; In-Line Filter available; For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system; with Hydraulic Power; Rack and Pinion Assembly |
| 2012 | Chevrolet | Camaro | — | — | N/A | with Hydraulic Power Assist; Includes Inner Tie Rods; In-Line Filter available; For warranty purposes it is recommended to always install a filter and to use suggested OE Fluid and flush the system; with Hydraulic Power; Rack and Pinion Assembly |
| 2011 | Chevrolet | Camaro | — | — | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2010 | Chevrolet | Camaro | — | — | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| No rows match your filter. | ||||||