/live/media/A1/A1_261881_Fro.jpg)
Cardone 26-1881 Rack and Pinion Assembly
| Brand | Cardone 26-1881 |
|---|---|
| Casting Material | Steel; aluminum |
| Distance Between Mounting Holes (in) | 0.00 |
| Distance Between Mounting Holes (mm) | 0.00 |
| E-Waste | No |
| Hose Port Type | O-ring |
| Input Shaft Diameter (in) | 0.69 |
| Input Shaft Diameter (mm) | 17.42 |
| Input Shaft Length (in) | 1.25 |
| Input Shaft Length (mm) | 31.75 |
| Number of Mounting Holes | 1 |
| Package Contents | Rack and pinion, sealing kit, instruction sheet |
| Pressure Port Thread Size | M14 x 1.5 |
| Product Condition | Remanufactured |
| Rack Length (in) | 41.19 |
| Rack Length (mm) | 1046.18 |
| Return Port Thread Size | M16 x 1.5 |
| Steering Rack Color | Black |
| Thread Length (in) | 2.47 |
| Thread Length (mm) | 62.71 |
| Tie Rod Ends Included | Yes |
| Total Turns Lock to Lock | 3.44 |
| Product line | Rack and Pinion Assembly |
| Fits | INFINITI · 3 vehicles |
Remanufactured OE replacement. Built to original equipment standards for a precise, direct-fit steering rack.
Factory-tested performance. Each unit is road-tested under extreme conditions and checked for on-car communication.
New sealing components. Fresh rubber seals and specialized lubricant help reduce leaks and extend service life.
Cross-references Infiniti 49001F6600 and Infiniti 4852110V06 for the same application. See all 2.
Remanufactured Steering Rack for Infiniti M30
Cardone 26-1881 is a remanufactured electronic power steering rack and pinion assembly built for precise OE-style fit and dependable steering response. It is engineered for 1990-1992 Infiniti M30 applications and includes new sealing components, a sealing kit, and an instruction sheet.
Key Features
- Remanufactured Original Equipment-style rack and pinion assembly for direct-fit replacement
- Fits 1990-1992 Infiniti M30, N/A
- New spool valve seals and rack donut seals installed to reduce internal leakage where applicable
- Specialized lubricant applied to support longer service life
- Factory test driven under simulated extreme operating conditions
- Protective black finish helps resist corrosion and rust
- Steel and aluminum construction
- Input shaft diameter: 0.69 in. / 17.42 mm
- Rack length: 41.19 in. / 1046.18 mm
- Total turns lock to lock: 3.44
Product Details
Cardone 26-1881 is remanufactured to rigorous performance standards and verified through factory testing that checks steering operation and on-car communications. The unit uses replaced rubber sealing components and a specialized lubricant to support durability, while the OE-style design helps maintain proper fit on the Infiniti M30. This part cross-references Infiniti part numbers 49001F6600 and 4852110V06 for the same application.
Common Steering Problems This Part Can Address
- Hard steering during the first few minutes of driving
- Internal fluid bypass caused by worn rack seals
- Steering that does not return to center after a turn
- Power steering pump whine caused by air in the system after service
- Leaks at the rack and pinion housing or sealing surfaces
Installation Notes
Fits 1990-1992 Infiniti M30, N/A. For installation, use an in-line filter and OE fluid, and flush the hydraulic power steering system when installing the rack and pinion assembly with inner tie rods for warranty validation. Verify front-end alignment and inspect the return line for restriction or kinks if steering does not return to center. Bleed the system completely after installation to remove trapped air.
Quality Assurance
Each Cardone rack and pinion assembly is remanufactured with new sealing components, tested on a factory drive cycle, and finished with a protective coating. The remanufacturing process also reduces the energy and raw material required versus producing a new part.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 1992 | INFINITI | M30 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 1991 | INFINITI | M30 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 1990 | INFINITI | M30 | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| No rows match your filter. | ||||