/live/media/A1/A1_262115_Fro.jpg)
Cardone 26-2115 Rack and Pinion Assembly
| Brand | Cardone 26-2115 |
|---|---|
| Casting Material | Steel; Aluminum |
| Distance Between Mounting Holes (in) | 3.75 |
| Distance Between Mounting Holes (mm) | 95.25 |
| E-Waste | No |
| Hose Port Type | O-Ring |
| Input Shaft Diameter (in) | 0.65 |
| Input Shaft Diameter (mm) | 16.59 |
| Input Shaft Length (in) | 1.00 |
| Input Shaft Length (mm) | 25.40 |
| Number of Mounting Holes | 2 |
| Package Contents | Rack and Pinion, Sealing Kit, Instruction Sheet |
| Pressure Port Thread Size | M14 x 1.5 |
| Product Condition | Remanufactured |
| Rack Length (in) | 50.75 |
| Rack Length (mm) | 1289.05 |
| Return Port Thread Size | M16 x 1.5 |
| Steering Rack Color | Black |
| Thread Length (in) | 1.83 |
| Thread Length (mm) | 46.56 |
| Tie Rod Ends Included | Yes |
| Total Turns Lock to Lock | 3.13 |
| Product line | Rack and Pinion Assembly |
| Fits | Mitsubishi · 8 vehicles |
Remanufactured OE replacement. Built to match original fit and function with factory-tested performance.
New sealing components. All rubber seals are replaced to help eliminate internal leaks.
Protective coating. Helps resist corrosion and rust for longer service life.
Cross-references Mitsubishi AW343511, Mitsubishi AW350131 and Mitsubishi MR197886 for the same application. See all 3.
Remanufactured Steering Rack for Mitsubishi Diamante
Restore precise steering response with this remanufactured Cardone rack and pinion assembly, part number 26-2115. Built for 1997-2004 Mitsubishi Diamante applications, it is rebuilt with new sealing components, specialized lubricant, and protective finishing for dependable operation.
Cardone’s Electronic Power Steering Rack and Pinion line focuses on OE-style fit and verified on-car communication, making this 26-2115 a direct replacement choice for Mitsubishi Diamante steering service.
Key Features
- Remanufactured Original Equipment-style rack and pinion assembly
- Fits 1997-2004 Mitsubishi Diamante
- Part number 26-2115
- New spool valve seals and rack donut seals installed where applicable
- 100% replacement of rubber sealing components
- Specialized lubricant applied for extended service life
- Factory test drive performed under simulated extreme operating conditions
- Protective coating helps resist corrosion and rust
- Rack length: 50.75 in. with 3.13 total turns lock to lock
- Includes rack and pinion, sealing kit, and instruction sheet
Product Details
This Cardone rack and pinion assembly is engineered for Mitsubishi Diamante steering systems that require a remanufactured replacement with OE-style fitment. The unit uses steel and aluminum construction, O-ring hose ports, M14 x 1.5 pressure port threads, and M16 x 1.5 return port threads. Tie rod ends are included, and the assembly is finished in black for a clean replacement appearance. Part number 26-2115 is also cross-referenced to Mitsubishi AW343511 and AW350131 for the same application.
What It Helps Address
- Excessive steering play or loose steering feel
- Internal fluid leakage from worn rack seals
- Hard steering caused by rack wear or internal bypass
- Steering that does not return smoothly after a turn
- Noise or inconsistent assist from a worn steering rack assembly
Installation Notes
- Compatible with 1997-2004 Mitsubishi Diamante, N/A position.
- Install an in-line filter and use OE fluid during service.
- Flush the hydraulic power steering system when installing the rack and pinion assembly with inner tie rods for warranty validation.
- Bleed the steering system completely after installation to remove air from the hydraulic circuit.
- Check front-end alignment and inspect return lines if the steering does not return to center.
Quality Assurance
Each Cardone remanufactured rack and pinion assembly is factory tested to verify operation and on-car communication before release. The remanufacturing process replaces rubber sealing components, applies specialized lubricant, and uses a protective finish to support long-term reliability while reducing raw material and energy use compared with producing a new part.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 2004 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2003 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2002 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2001 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 2000 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 1999 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 1998 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| 1997 | Mitsubishi | Diamante | N/A | Install in-line filter and use OE fluid; flush hydraulic power system when installing Rack and Pinion Assembly with inner tie rods for warranty validation.; Rack and Pinion Assembly |
| No rows match your filter. | ||||