Cardone 48-306 Transfer Case Motor

Transfer Case Motor for Ram, Dodge, and Chrysler

Restore transfer case shifting performance with this remanufactured Cardone transfer case motor. Cardone 48-306 is built for direct replacement use on select Ram, Dodge, Chrysler, and Mitsubishi applications, including Ram 1500, Ram 2500, Ram 3500, Dakota, Durango, Aspen, and Raider models with a 2-speed transfer case where specified.

The Cardone Transfer Case Motor line focuses on OE-style operation, with remanufacturing steps that address common failure points and help return the transfer case to proper engagement. Part number 48-306 is a practical choice for drivers dealing with 4WD shift concerns on covered vehicles.

• Remanufactured transfer case motor for direct replacement service
• Steel housing for durable component support
• Blade-style connector/terminal configuration
• Motor magnets are fully recharged for consistent operation
• Transfer case motor sensors are replaced with new, OE-quality sensors
• Assembled with the correct lubricant amount for quiet operation and long service life
• 100% computer tested at three stages during remanufacturing

Detailed Product Overview

Cardone 48-306 is engineered to meet or exceed original equipment performance by remanufacturing the transfer case motor and correcting known design weaknesses identified through reverse engineering. This approach supports reliable transfer case engagement on vehicles such as the Dodge Ram 1500, Ram 2500, Ram 3500, Dodge Dakota, Dodge Durango, Chrysler Aspen, and Mitsubishi Raider when equipped as listed. This part cross-references Chrysler/Dodge/Mitsubishi 5143477AA for the same application.

Common Issues This Part Can Address

• Service 4WD light illuminated
• Transfer case will not shift into 4HI or 4LO
• Weak or inconsistent transfer case motor movement
• Transfer case engagement failure after motor wear
• Error codes related to transfer case motor operation

Installation Notes and Tips

Before installation, manually shift the transfer case into the two-wheel drive position at the shift shaft. The replacement motor drive is factory-set in the 2WD position, and it should not be operated off the transfer case or it can be damaged and trigger an error code. A crescent wrench can be used for this operation. If the transfer case motor failed in 4 Wheel Drive Low or High, shift the transfer case to match the motor position before installing the replacement unit.

After installation, verify that the transfer case control module has no stored DTCs and confirm calibration status if the 4WD system remains inoperative. If the motor sounds weak during shift attempts, inspect the front axle lock actuator as well.

Quality Assurance

Each Cardone remanufactured transfer case motor is computer tested at three points during the remanufacturing process. The unit is also rebuilt with replaced sensors, recharged magnets, and controlled lubrication to support reliable operation and long-term performance.

Vehicle Fitment

• Fits 2011-2012 Ram 2500, transfer case motor
• Fits 2011-2012 Ram 3500, transfer case motor
• Fits 2005-2011 Dodge Dakota, transfer case motor
• Fits 2011 Ram Dakota, transfer case motor
• Fits 2008-2010 Dodge Ram 1500, with 2 speed transfer case; ID #(s) NVG 48408; transfer case motor
• Fits 2008-2010 Dodge Ram 2500, with 2 speed transfer case; transfer case motor
• Fits 2006-2010 Dodge Ram 3500, with 2 speed transfer case; transfer case motor
• Fits 2007-2009 Chrysler Aspen, with 2 speed transfer case; transfer case motor
• Fits 2005-2009 Dodge Durango, with 2 speed transfer case; transfer case motor
• Fits 2006-2009 Mitsubishi Raider, transfer case motor
• Fits 2006-2007 Dodge Ram 1500, ID #(s) NVG 48408; transfer case motor
• Fits 2006-2007 Dodge Ram 2500, with 2 speed transfer case; ID #(s) NVG 48408; transfer case motor