Cardone 65-9825 Drive Shaft - Rear
OE Quality 60-Day Returns
Cardone
 Driveshaft / Prop Shaft

Cardone 65-9825 Drive Shaft - Rear

Brand Cardone 65-9825
Position Rear
Drive Shaft Material Steel
E-Waste No
Greasable No
Length (in) 36 5/8"
Length (mm) 930
Measurement Method Measurement taken from end of flange face to end of flange face
Product Condition Remanufactured
Tubing Outer Diameter (in) 2.01
Tubing Outer Diameter (mm) 51
Product line Driveshaft / Prop Shaft
Fits Ford · 7 vehicles

OE direct replacement. Built to match O.E. form, fit and function.

100% dynamically balanced. Delivers vibration-free operation and longer joint life.

Steel construction. Remanufactured drive shaft with lubricated slip yokes to help prevent wear.

$347.32Free shipping
Out of stock
Step 1 — Confirm fitment
Free return shipping if it doesn't fit when you check fitment here first.

Select your vehicle to confirm fitment
Verify this part fits before purchasing β€” free returns if it doesn't
Step 2 — Quantity
Order total $347.32
Free shipping to the continental U.S.
Free returns within 60 days if it doesn't fit when fitment is verified.
Not what you need? See all Drive Shaft options

Cardone 65-9825 Drive Shaft for Bronco II

Cardone 65-9825 is a remanufactured rear drive shaft built for specific Ford Bronco II applications. It is engineered to match OE form, fit, and function, with dynamic balancing for smooth operation at speed.

Key Features

  • Steel drive shaft construction
  • Remanufactured to OE-style specifications
  • 100% dynamically balanced at 3200 RPM for vibration-free operation
  • Lubricated slip yokes to help reduce premature wear
  • 36 5/8 in. (930 mm) length measured flange face to flange face
  • 2.01 in. (51 mm) tubing outer diameter
  • Rear position application for select Ford Bronco II models

Product Details

This Cardone Driveshaft / Prop Shaft line focuses on engineering and testing prop shafts to deliver consistent driveline performance. Part number 65-9825 is built in steel and remanufactured to match original equipment dimensions and operating characteristics. For Ford Bronco II rear driveline service, this shaft is listed for 1986-1990 Bronco II models with a 36-5/8 in. (930 mm) long driveshaft and GKN conversion design, with one 1989 application noted from 06/1989.

This part cross-references no listed interchange numbers in the provided data.

What It Helps Address

  • Driveline vibration at highway speeds
  • Wear related to unbalanced or out-of-spec prop shafts
  • Noise caused by driveline imbalance
  • Fitment issues when replacing a worn rear drive shaft on a Ford Bronco II
  • Premature slip yoke wear

Installation Notes and Tips

Measure from flange face to flange face before ordering to confirm the 36 5/8 in. (930 mm) length. Verify rear-position fitment and the GKN conversion design requirement for your Ford Bronco II before installation. Inspect related driveline components, including U-joints and mounting surfaces, so the replacement shaft can be installed on clean, accurate mating points.

Quality Assurance

Cardone engineers and tests this prop shaft to match OE performance targets, and each unit is dynamically balanced for smooth operation. The remanufactured construction is intended to provide consistent driveline performance for compatible Ford Bronco II applications.

Related reading

This part fits 7 vehicles
Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
YearMakeModelDrive TypeTransmissionPositionNotes
1990FordBronco II4WDManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1990FordBronco IIRWDManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1989FordBronco II4WDManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1989FordBronco IIRWDManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; From 06/1989; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1988FordBronco II—ManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1987FordBronco II—ManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft
1986FordBronco II—ManualRearwith 36-5/8" (930 mm) Long Driveshaft; with GKN Conversion Design; Measurement taken from end of flange face to end of flange face; Driveshaft / Prop Shaft