Cardone 67-6033 Fuel Injection Throttle Body

Remanufactured Electronic Throttle Body

The Cardone 67-6033 Fuel Injection Throttle Body is a remanufactured electronic throttle body built for precise air management and OE-style fitment. It is engineered for Ford and Lincoln applications including the F-150, Explorer, Bronco, Ranger, Mustang, Edge, Aviator, Nautilus, Continental, MKZ, MKX, Fusion, and Lincoln Continental platforms listed below.

As part of the Cardone Fuel Injection Throttle Body line, this unit is remanufactured from an original equipment core and restored to meet application-specific requirements. The process focuses on restoring proper throttle response, airflow consistency, and sensor performance for modern drive-by-wire systems.

• Part number 67-6033
• 60 mm bore diameter
• Electric throttle body actuation
• Round inlet and round outlet design
• Aluminum housing with plastic, steel, and aluminum construction
• Integrated high and low throttle position sensors tested to OE characteristics
• Remanufactured Original Equipment replacement for direct vehicle fit
• Package contents: electronic throttle body and instruction sheet

Detailed Product Overview

This Cardone remanufactured electronic throttle body is cleaned, inspected, renewed, and tested to restore critical throttle functions. The bore is cleaned with a specialized process that helps preserve the throttle bore surface for consistent airflow, while internal components such as sensors, gears, connectors, and seals are evaluated and replaced as needed. Final testing includes response time and airflow checks at multiple points, which is important for vehicles that rely on electronic throttle control for idle management, acceleration, cruise control, traction control, stability control, and torque management. If you are replacing a throttle body on a 2019-2025 Ford F-150, 2020-2025 Ford Explorer, or 2020-2025 Lincoln Aviator, this part number 67-6033 is built for the application-specific OE replacement role.

Common Problems This Part Addresses

• Throttle response issues caused by worn internal sensors
• Rough idle or unstable idle speed from throttle plate wear
• Reduced airflow control from contamination in the throttle bore
• Electronic throttle warning lights and fail-safe operation
• Driveability concerns tied to inconsistent throttle actuator performance

Installation Notes

A relearn calibration procedure is necessary after installation of the replacement throttle body. Consult the vehicle service manual for the correct relearn steps before returning the vehicle to service. Do not install a larger-bore throttle body to chase horsepower gains; this unit is calibrated for the listed Ford and Lincoln applications. Bypassing coolant hoses is not recommended where the OE design uses them for temperature control. This part cross-references Ford GB8Z9E926A for the same application.

Fits 2021-2025 Ford Bronco, N/A. Fits 2020-2025 Ford Explorer, N/A. Fits 2019-2025 Ford F-150, N/A. Fits 2019-2025 Ford Ranger, N/A. Fits 2020-2025 Lincoln Aviator, N/A. Fits 2019-2024 Ford Edge, N/A. Fits 2019-2023 Ford Mustang, N/A. Fits 2019-2023 Lincoln Nautilus, N/A. Fits 2017-2020 Lincoln Continental, N/A. Fits 2017-2020 Lincoln MKZ, N/A. Fits 2017-2019 Ford Fusion, N/A. Fits 2015-2018 Ford Edge, N/A. Fits 2015-2018 Ford F-150, N/A. Fits 2015-2018 Ford Mustang, N/A. Fits 2016-2018 Lincoln MKX, N/A.

Quality Assurance

Each Cardone remanufactured throttle body is disassembled, inspected, and renewed or replaced component by component, then tested for critical functions before release. The remanufacturing process also reduces raw material and energy use compared with producing a new part, supporting a more resource-efficient repair choice.