/live/media/A1/A1_7230201F_Ang.jpg)
Cardone 72-30201F Engine Control Module (ECM)
| Brand | Cardone 72-30201F |
|---|---|
| Length | 226.06 |
| Length | 8.9 |
| Flash Programming Required | Yes |
| Flashable | Yes |
| Removable PROM | No |
| Width | 139.7 |
| Width | 5.5 |
| Terminal Type | Pin |
| Mounting Hardware Included | No |
| Height | 1.875 |
| Height | 47.62 |
| Grade Type | Standard replacement |
| Connector Quantity | 3 |
| Connector Shape | Rectangle |
| Mounting Hole Quantity | 3 |
| Terminal Quantity | 114 |
| Connector Gender | Male |
| Terminal Gender | Male |
| Contains Electronic Components | Circuit board |
| Does it require SDS | No |
| E-Waste | Yes |
| FAA_A1 | “ecm” stands for electronic control module. “pcm” stands |
| FAA_A2 | Some gm applications have a knock module that must be transferred |
| FAA_A3 | No, not all ford vehicles require pats reset. check the pats cha |
| FAA_A5 | Prior to replacing the original ecm/pcm, the installer should det |
| FAA_A6 | Yes, most gm vehicles have a vats, pass key or pass lock anti-the |
| FAA_A7 | Not necessarily. there is a 30-minute manual procedure that can |
| FAA_A8 | Chrysler models 1996 and newer will need to be vin programmed. |
| FAA_A9 | Check engine light staying on after resetting, engine turning off |
| Product line | Remanufactured Engine Control Module |
| Fits | Nissan · 1 vehicle |
Remanufactured replacement. Designed to meet or exceed O.E. performance.
Computer tested. Each unit is verified for reliability before it leaves the plant.
Flashable module. Requires flash programming for proper setup.
Cross-references 237106Y310, 237106Y311 and 237106Y312 for the same application. See all 7.
Remanufactured ECM for 2003 Nissan Maxima
This Cardone remanufactured engine control module is built for the 2003 Nissan Maxima and is engineered to restore proper engine management after an ECM failure. Part number 72-30201F is a flashable, computer-tested replacement that follows the original module layout and connector design for a direct service solution.
Key Features
- Fits 2003 Nissan Maxima, N/A
- Cardone Remanufactured Engine Control Module, part number 72-30201F
- Flash programming required; module is flashable
- Standard replacement grade with 3 rectangular male connectors
- 114 terminal pin design for OE-style electrical interface
- Remanufactured at Cardone’s Philadelphia manufacturing plant
- Critical components are re-soldered or replaced during remanufacturing
- 100% computer tested for electrical reliability
- Package contents: module and instruction sheet
Product Details
Cardone’s remanufactured electronic and powertrain control module line is focused on correcting common failure points found in original units. For this 2003 Nissan Maxima ECM, the module is reverse engineered to identify design weaknesses, then rebuilt with attention to the circuit board and other critical internal components. The result is a remanufactured engine control module that supports accurate fuel, spark, and engine operation management when the original unit has failed. Part number 72-30201F is also referenced for related applications under OE-style interchange numbers.
This part cross-references select OE numbers such as 237106Y310 and A56T63ZP4 for the same application.
Common Problems This ECM Can Address
- Check Engine Light that remains on after reset
- Engine shutting off unexpectedly
- Loss of spark or fuel injection control
- Intermittent starting problems
- Loss of fuel pump pulse signal
Installation Notes
Flash programming is required after installation. Before replacing the original ECM, verify the root cause of the failure, including power and ground integrity, wiring harness condition, and any shorted relays or solenoids. Confirm connector condition, mounting points, and calibration requirements before programming the replacement module. Part number 72-30201F should be installed and programmed according to the vehicle service procedure for the 2003 Nissan Maxima.
Quality Assurance
Cardone remanufactures this ECM to meet or exceed original equipment performance targets. Each unit is computer tested after critical internal repairs, and the remanufacturing process is designed to address known failure modes found in the original control module. The product is supplied as a remanufactured electronic control module for dependable service restoration.
| Year | Make | Model | Transmission | Position | Notes |
|---|---|---|---|---|---|
| 2003 | Nissan | Maxima | Automatic | N/A | Remanufactured Engine Control Module |
| No rows match your filter. | |||||