Dana Spicer 5-1508X Universal Joint - Rear Driveshaft at Rear Axle, Rear Driveshaft at Support Bearing or Rear Driveshaft at Transmission

Spicer ISR Universal Joint for Toyota Pickup

The Dana Spicer FSGR 5-1508X is a greaseable ISR-style universal joint built for Toyota Pickup driveline service. It uses steel construction, internal snap rings, and 26 mm bearing cap diameters to match the specified rear driveshaft applications.

For Toyota Pickup rear driveshaft repair, this Spicer universal joint is engineered for long service life in light vehicle use. The 5-1508X is a direct-fit option for rear driveshaft positions at the transmission, support bearing, and rear axle where the listed OE-style dimensions and ISR cap type are required.

Key Features

• Part number: 5-1508X
• Brand: Dana Spicer, FSGR line
• Universal joint, ISR style
• Greaseable design for service access
• Steel construction
• Round bearing caps with internal snap rings
• Bearing cap diameter: 1.025 in. / 26.0 mm
• Length A and Length B: 2.200 in. / 55.9 mm
• OEM reference: Toyota

Detailed Description

The Dana Spicer 5-1508X universal joint is built for Toyota Pickup driveline applications that call for a greaseable ISR-style joint with 1.025-inch bearing caps. Spicer universal joints are manufactured for a wide range of vehicle duty cycles, from light vehicle service to commercial and off-highway use, and this unit follows the same dimensional and material requirements needed for accurate driveline service. If you are replacing a worn Toyota Pickup rear driveshaft universal joint, the 5-1508X provides the correct cap diameter, internal snap ring retention, and steel body construction for the listed positions.

This part cross-references Hayden 390 and SKF UJ390 for the same application. It is a strong match for Toyota Pickup rear driveshaft service where the vehicle uses a grease fitting and the specified ISR configuration.

What It Helps Fix

• Driveline vibration from a worn rear driveshaft joint
• Clunking or clicking during acceleration or deceleration
• Need for a greaseable replacement joint on Toyota Pickup driveline service
• Excess play at the transmission, support bearing, or rear axle driveshaft connection
• Noise caused by worn bearing caps or damaged snap ring retention

Installation Notes and Fitment

Compatible With Toyota Pickup rear driveshaft applications listed below. Verify bearing cap diameter, ISR style, and snap ring type before installation. Use proper driveline service procedures and inspect the yokes, shaft, and retaining grooves for wear before pressing in the new joint.

• Fits 1984-1988 Toyota Pickup, rear driveshaft at transmission; 1 piece driveshaft; greaseable; with 1 piece rear drive shaft; FSGR
• Fits 1984-1988 Toyota Pickup, rear driveshaft at rear axle; 1 piece driveshaft; greaseable; with 1 piece rear drive shaft; FSGR
• Fits 1984-1988 Toyota Pickup, rear driveshaft at transmission; 2 piece driveshaft; greaseable; fits vehicles with 2 piece rear drive shaft; FSGR
• Fits 1984-1988 Toyota Pickup, rear driveshaft at support bearing; 2 piece driveshaft; greaseable; fits vehicles with 2 piece rear drive shaft; FSGR
• Fits 1984-1988 Toyota Pickup, rear driveshaft at rear axle; 2 piece driveshaft; greaseable; fits vehicles with 2 piece rear drive shaft; FSGR
• Fits 1979-1983 Toyota Pickup, rear driveshaft at transmission; except 1/2 ton; greaseable; with 1 piece rear drive shaft; FSGR
• Fits 1979-1983 Toyota Pickup, rear driveshaft at rear axle; except 1/2 ton; greaseable; with 1 piece rear drive shaft; FSGR
• Fits 1979-1983 Toyota Pickup, rear driveshaft at transmission; except 1/2 ton; greaseable; with 2 piece rear drive shaft; FSGR
• Fits 1979-1983 Toyota Pickup, rear driveshaft at support bearing; except 1/2 ton; greaseable; with 2 piece rear drive shaft; FSGR
• Fits 1979-1983 Toyota Pickup, rear driveshaft at rear axle; except 1/2 ton; greaseable; with 2 piece rear drive shaft; FSGR
• Fits 1969-1978 Toyota Pickup, rear driveshaft at transmission; universal joint with grease fitting; FSGR
• Fits 1969-1978 Toyota Pickup, rear driveshaft at rear axle; universal joint with grease fitting; FSGR
• Fits 1966 Toyota Pickup, rear driveshaft at transmission; universal joint with grease fitting; FSGR
• Fits 1966 Toyota Pickup, rear driveshaft at rear axle; universal joint with grease fitting; FSGR

Quality Assurance

Dana Spicer manufactures driveline components to OE-level dimensional standards for service applications. The FSGR 5-1508X is built with steel construction, greaseable serviceability, and internal snap ring retention to support accurate fitment in the listed Toyota Pickup driveline positions.