/live/media/DE/DE_TA3020_Ang.jpg)
Delphi TA3020 Steering Tie Rod End - Right Outer
| Brand | Delphi TA3020 |
|---|---|
| Position | Right Outer |
| Adjustable | No |
| Bearing Material | Plastic |
| Color | Black |
| Cone Outside Diameter | 18.6 |
| Dust Boot Included | Yes |
| Dust Boot Material | Choloroprene Rubber (CR) |
| End 1 Thread Diameter | 0.551 |
| End 1 Thread Diameter | 14.0 |
| End 1 Thread Direction | Clockwise |
| End 2 Gender | Female |
| End 2 Thread Diameter | 0.551 |
| End 2 Thread Diameter | 14.0 |
| End 2 Thread Direction | Clockwise |
| End 2 Thread Pitch | 1.5 |
| Friction Material Thickness | Coated |
| Grease Fitting Included | No |
| Greaseable | No |
| Height | 234.1 |
| Housing Material | Steel |
| Item Grade | Standard Replacement |
| Length Stud Center to End | 8.374 |
| Length Stud Center to End | 212.7 |
| Mounting Hardware Included | Yes |
| Position(s) | Front Right Outer |
| Pre-Greased | Yes |
| Stud Type | Threaded |
| Tie Rod Material | Steel |
| Tube Diameter | 0.827 |
| Tube Diameter | 21.0 |
| Type | Bent |
| Weight | 2.19 |
| Width | 66.0 |
| Fits | Mercedes-Benz · 4 vehicles |
Standard replacement. OE expertise and dimensional analysis help match the original part.
Coated steel construction. Built for durability with a pre-greased, sealed design.
Dust boot included. Helps protect the joint from contamination and wear.
Cross-references Beck/Arnley 101-7482, Mevotech Supreme MS106114 and 212 330 22 03 for the same application. See all 6.
Delphi TA3020 Front Right Outer Tie Rod End
The Delphi TA3020 steering tie rod end is a standard replacement for the front right outer position on select Mercedes-Benz E-Class applications. It combines OE-focused dimensional analysis with materials and testing that support consistent steering response and proper fitment.
- Front right outer steering tie rod end
- Pre-greased design with dust boot included
- Steel housing and steel tie rod construction
- Coated black finish for added surface protection
- Clockwise thread direction at both ends
- Mounting hardware included
- Non-adjustable, non-greaseable design
- End 2 female thread, 14.0 mm thread diameter, 1.5 pitch
OE-Style Steering Replacement
Delphi applies OE engineering practices to its aftermarket steering portfolio, using dimensional and material analysis to help ensure the part matches the original application. The TA3020 is built for the front right outer steering position and is listed for 2013-2014 Mercedes-Benz E400 and 2010-2011 Mercedes-Benz E550. This part cross-references Beck/Arnley 101-7482 for the same application.
Common Steering Issues It Can Address
- Excessive play or looseness in the front right steering linkage
- Clunking or knocking from the outer tie rod area
- Uneven tire wear caused by worn steering components
- Steering wander or reduced directional stability
- Failed dust boot or contaminated tie rod joint
Installation Notes
Verify front right outer fitment before installation on Mercedes-Benz E400 and Mercedes-Benz E550 applications. Inspect the mating steering components, confirm thread direction and dimensions, and perform a wheel alignment after replacement. The pre-greased joint and included dust boot support a clean service replacement, while the bent steel design matches the original steering geometry.
Quality Assurance
Delphi subjects steering components to extreme temperature testing from below -40 degrees C to above 120 degrees C, along with 720 hours of salt spray exposure. The brand also uses OE-level dimensional and material checks to support fitment consistency and durability in aftermarket service.
| Year | Make | Model | Body Type | Drive Type | Position | Notes |
|---|---|---|---|---|---|---|
| 2014 | Mercedes-Benz | E400 | — | — | Right Outer | — |
| 2013 | Mercedes-Benz | E400 | — | — | Right Outer | — |
| 2011 | Mercedes-Benz | E550 | Sedan | RWD | Right Outer | — |
| 2010 | Mercedes-Benz | E550 | Sedan | RWD | Right Outer | — |
| No rows match your filter. | ||||||