HomeSteering > Steering, Gear and Related ComponentsDelphi TA3566 Steering Tie Rod End - Front Left Outer
Part #: TA3566

Delphi TA3566 Steering Tie Rod End - Front Left Outer

Front Left Outer
⚙️ 8 vehicles fit this part
🔍
Select your vehicle to confirm fitment
Verify this part fits before purchasing — free returns if it doesn't
$33.83Free Shipping
🚚Free ShippingNo Cost to Continental U.S.
🔄Free Returns*Wrong fit? No cost
🛡️60-Day ReturnsMoney back guarantee
*Free return shipping only qualifies if our fitment verification tool is used.
🔥
✅ In Stock · Ready To Ship Most orders ship same-day if ordered before 1pm CST.
OE Direct Replacement — Bolt-on fit, no modifications needed
🚗Fitment: Honda, Odyssey
🔄Easy Returns — Return within 60 days for a full refund
🚚Fast Shipping — Most orders ship same business day before 1pm CST

Front Left Outer Tie Rod End for Honda Odyssey

Delphi TA3566 is a steering tie rod end built for the front left outer position on select Honda Odyssey models. It combines OE-based dimensional analysis with materials chosen for consistent steering response and proper fitment.

  • Fits 2018-2025 Honda Odyssey, front left outer
  • Delphi OE-style aftermarket steering component
  • Pre-greased design with dust boot included
  • Steel housing and steel tie rod construction
  • Painted black finish
  • Standard replacement grade
  • Mounting hardware included
  • Part number: TA3566

Built for Steering Precision

Delphi TA3566 is engineered as a direct replacement steering tie rod end for the front left outer location on the Honda Odyssey. Delphi applies OE-focused testing and material analysis to help ensure dimensional accuracy, proper compatibility, and dependable performance in everyday driving. This part cross-references Mevotech Supreme MS60667 for the same application.

Common Problems This Part Can Address

  • Loose or vague steering feel at the front end
  • Clunking or play from a worn outer tie rod end
  • Uneven tire wear caused by steering linkage wear
  • Steering wheel wander or poor directional stability
  • Inspection failure from excessive steering component movement

Installation Notes and Tips

Fits 2018-2025 Honda Odyssey, front left outer. Verify the steering linkage orientation, thread direction, and position before installation. This bent tie rod end uses male and female ends with clockwise thread direction on both ends, and it is pre-greased with a rubber dust boot already installed. After replacement, a professional wheel alignment is recommended to restore correct steering geometry.

Quality Assurance

Delphi subjects its steering components to extreme temperature and corrosion testing, including exposure below -40 degrees C, above 120 degrees C, and extended salt spray testing. The TA3566 also reflects Delphi’s OE dimensional and material analysis process for aftermarket steering parts.

BrandDelphi
Part NumberTA3566
ColorBlack
End 1 GenderMale
End 2 GenderFemale
FinishPainted
Pre-GreasedYes
Grease Fitting IncludedNo
Dust Boot IncludedYes
TypeBent
Mounting Hardware IncludedYes
Height78.30
Grade TypeStandard replacement
Housing MaterialSteel
AdjustableNo
GreaseableNo
Weight1.63
Cone Outside Diameter0.711
Cone Outside Diameter18.05
Bearing MaterialPolyoxymethylene (pom)
End 1 Thread DirectionClockwise (right)
End 2 Thread DirectionClockwise (right)
Stud TypeThreaded
Head Drive TypeHex
Length Stud Center to End206.50
Length Stud Center to End8.130
Dust Boot MaterialRubber
Tie Rod MaterialSteel
Position(s)Front left outer

This part fits 8 vehicles. Search below:

YearMakeModelPositionNotes
2025HondaOdysseyFront Left Outer
2024HondaOdysseyFront Left Outer
2023HondaOdysseyFront Left Outer
2022HondaOdysseyFront Left Outer
2021HondaOdysseyFront Left Outer
2020HondaOdysseyFront Left Outer
2019HondaOdysseyFront Left Outer
2018HondaOdysseyFront Left Outer

* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.

This part directly replaces or is cross-referenced with the following part numbers:

101873053560-THR-A02MS60667

Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.