/live/media/DE/DE_TA3594_FRO.JPG)
OE Quality
60-Day Returns
/live/media/DE/DE_TA3594_FRO.JPG)
/live/media/DE/DE_TA3594_ANG.JPG)
/live/media/DE/DE_TA3594_TOP.JPG)
/live/media/DE/DE_TA3594_BAC.JPG)
/live/media/DE/DE_TA3594_BOT.JPG)
/live/media/DE/DE_TA3594_LEF.JPG)
/live/media/DE/DE_TA3594_RIG.JPG)
Delphi TA3594 Steering Tie Rod End - Inner
Delphi Inner Tie Rod End for Nissan Kicks
Delphi TA3594 is a straight inner steering tie rod end built for OE-style replacement performance. It is listed for 2018-2020 Nissan Kicks applications and uses a steel housing with a steel tie rod for durable steering linkage service.
Key Features
- Part number: TA3594
- Fits 2018-2020 Nissan Kicks, inner steering position
- Straight tie rod end design
- Pre-greased for initial service
- Steel housing and steel tie rod construction
- Standard replacement grade
- Mounting hardware included
- Male threaded ends with left-hand thread direction
OE-Style Steering Replacement
Delphi applies OE engineering knowledge to its aftermarket steering parts, with dimensional and material analysis used to support proper part matching. TA3594 is a non-adjustable inner tie rod end with a threaded stud design, built for the steering linkage on Nissan Kicks models from 2018 through 2020. This part cross-references Mevotech Supreme MS30754 for the same application.
Common Problems This Part Can Address
- Excessive steering play from a worn inner tie rod end
- Clunking or looseness in the steering linkage
- Uneven tire wear caused by steering component wear
- Imprecise steering response on Nissan Kicks models
- Replacement needs after inspection reveals joint wear or corrosion
Installation Notes and Tips
Confirm the inner steering position before ordering and match the left-hand thread direction to the original component. Because this is a straight, non-adjustable tie rod end, alignment should be checked after installation. Verify fitment against the vehicle’s steering setup for 2018-2020 Nissan Kicks applications before service begins.
Quality Assurance
Delphi subjects steering components to temperature extremes below -40 degrees C and above 120 degrees C, along with extended salt-spray exposure, to evaluate durability and corrosion resistance. The brand’s OE-focused testing and dimensional analysis support consistent replacement quality for Nissan Kicks steering service.
| Brand | Delphi |
| Part Number | TA3594 |
| Length | 257.00 |
| End 1 Gender | Male |
| End 2 Gender | Male |
| Pre-Greased | Yes |
| Grease Fitting Included | No |
| Dust Boot Included | No |
| Type | Straight |
| Mounting Hardware Included | Yes |
| Height | 34.00 |
| Grade Type | Standard replacement |
| Housing Material | Steel |
| Tube Diameter | 0.470 |
| Tube Diameter | 12.00 |
| Adjustable | No |
| Greaseable | No |
| Weight | 1.09 |
| Bearing Material | Plastic |
| End 1 Thread Direction | Counterclockwise (left) |
| End 2 Thread Direction | Counterclockwise (left) |
| Stud Type | Threaded |
| Length Stud Center to End | 1.378 |
| Length Stud Center to End | 35.00 |
| Tie Rod Material | Steel |
| Position(s) | Inner |
This part fits 3 vehicles. Search below:
| Year | Make | Model | Submodel | Position | Notes |
|---|---|---|---|---|---|
| 2020 | Nissan | Kicks | SV | Inner | |
| 2019 | Nissan | Kicks | Inner | ||
| 2018 | Nissan | Kicks | Inner |
* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
This part directly replaces or is cross-referenced with the following part numbers:
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.