/live/media/DE/DE_TA3622_FRO.JPG)
Delphi TA3622 Steering Tie Rod End - Front Inner
| Brand | Delphi TA3622 |
|---|---|
| Position | Front Inner |
| Length | 317.00 |
| Color | Silver |
| End 1 Gender | Male |
| End 2 Gender | Male |
| Finish | E-coated |
| Pre-Greased | Yes |
| Grease Fitting Included | No |
| Dust Boot Included | No |
| Width | 39.00 |
| Type | Straight |
| Mounting Hardware Included | Yes |
| Height | 39.00 |
| Grade Type | Standard replacement |
| Housing Material | Steel |
| Tube Diameter | 0.657 |
| Tube Diameter | 16.70 |
| Adjustable | No |
| Greaseable | No |
| Weight | 1.367 |
| Bearing Material | Polyoxymethylene (pom) |
| End 1 Thread Direction | Clockwise (right) |
| End 2 Thread Direction | Counterclockwise (left) |
| Stud Type | Threaded |
| Head Drive Type | Hex |
| Length Stud Center to End | 1.457 |
| Length Stud Center to End | 37.00 |
| Tie Rod Material | Steel |
| Fits | Jeep · 5 vehicles |
Standard replacement. OE expertise and dimensional analysis help ensure compatibility.
E-coated steel construction. Resists corrosion and stands up to demanding conditions.
Pre-greased design. Ready for installation with mounting hardware included.
Cross-references Mevotech Supreme MS25740, MOOG Chassis Products EV801534 and Suspensia X22TR0212 for the same application. See all 7.
OE-Style Steering Tie Rod End for Jeep Compass
Delphi TA3622 is a front inner steering tie rod end for 2017-2021 Jeep Compass models. Built as a standard replacement part, it follows OE-style dimensions and material analysis to support proper steering geometry and consistent fitment.
- Fits 2017-2021 Jeep Compass, front inner
- Delphi OE-based aftermarket steering component
- Straight tie rod end with steel housing and steel tie rod material
- Pre-greased design with no grease fitting required
- E-coated silver finish for added corrosion resistance
- Includes mounting hardware
- Male end 1 and male end 2 configuration
- Thread directions: clockwise right and counterclockwise left
Fitment and Application Details
Delphi TA3622 is engineered for the front inner steering position on the Jeep Compass from 2017 through 2021. If you are searching for a Jeep Compass front inner tie rod end, Delphi TA3622 provides a direct replacement option that matches OE-style dimensions and mounting requirements. This part cross-references MOOG Chassis Products EV801534 for the same application.
What This Part Helps Address
- Loose or imprecise steering feel at the front inner linkage
- Clunking or play caused by worn steering joint components
- Uneven steering response from a fatigued tie rod end
- Corrosion-related wear on exposed steering hardware
- Replacement needs after inspection reveals steering linkage wear
Installation Notes and Tips
Confirm the front inner position before ordering and compare thread direction, length, and mounting style to the original part. Delphi TA3622 is pre-greased and does not use a grease fitting, so no routine greasing point is provided. After installation, a professional wheel alignment is recommended to restore steering geometry and tire wear patterns.
Quality Assurance
Delphi applies OE-focused dimensional and material analysis to its steering portfolio and subjects parts to temperature extremes below -40 degrees C and above 120 degrees C, along with 720 hours of salt spray exposure. Delphi TA3622 is built to support OE-level fit and durability expectations for the Jeep Compass platform.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 2021 | Jeep | Compass | Front Inner | — |
| 2020 | Jeep | Compass | Front Inner | — |
| 2019 | Jeep | Compass | Front Inner | — |
| 2018 | Jeep | Compass | Front Inner | — |
| 2017 | Jeep | Compass | Front Inner | — |
| No rows match your filter. | ||||