/live/media/DE/DE_TD1482W_Ang.jpg)
Delphi TD1482W Suspension Stabilizer Bar Bushing Kit - Rear
| Brand | Delphi TD1482W |
|---|---|
| Position | Rear |
| Bushing Quantity | 2 |
| Color | Black |
| Grade Type | Regular |
| Height | 1.287 |
| Height | 32.7 |
| Inside Diameter | 0.492 |
| Inside Diameter | 12.5 |
| Item Grade | Standard Replacement |
| Material | Rubber |
| Outside Diameter | 0.945 |
| Outside Diameter | 24.0 |
| Width | 1.339 |
| Width | 34.0 |
| Fits | Honda · 5 vehicles |
Standard replacement. OE expertise helps ensure compatibility with the original part.
Rubber construction. Provides dependable cushioning and vibration control.
Tested for extreme temperatures and 720 hours of salt spray.
Cross-references Beck/Arnley 101-6994, Mevotech Supreme MS60823 and MOOG Chassis Products K201491 for the same application. See all 4.
Rear Stabilizer Bar Bushing Kit for Honda CR-V
Delphi TD1482W is a rear suspension stabilizer bar bushing kit built for 1997-2001 Honda CR-V applications. It uses rubber construction and OE-focused dimensional analysis to support a precise replacement for the rear sway bar mounting points.
For buyers searching for a rear stabilizer bar bushing kit for 1997-2001 Honda CR-V, Delphi TD1482W offers a standard replacement solution with OE-style sizing and material selection. This part is also referenced by TD1482W when comparing aftermarket suspension bushing options for the same application.
Key Features
- Fits 1997-2001 Honda CR-V, rear
- Rubber bushing material with black finish
- Standard replacement grade for suspension service
- Inside diameter: 0.492 in / 12.5 mm
- Outside diameter: 0.945 in / 24.0 mm
- Width: 1.339 in / 34.0 mm
- Height: 1.287 in / 32.7 mm
- Designed around OE dimensional and material analysis
- Tested for temperature extremes and salt-spray exposure
Detailed Description
Delphi TD1482W is a rear stabilizer bar bushing kit for the Honda CR-V, engineered as a standard replacement part for the rear suspension. Delphi applies OE-based dimensional and material analysis to help ensure proper fit and consistent bushing performance in the stabilizer bar mounting location. The rubber construction is selected for suspension service where controlled compliance and noise isolation are important.
Delphi validates its steering and suspension components through temperature testing below -40 degrees C and above 120 degrees C, along with extended salt-spray exposure. That testing approach supports dependable performance in demanding road and weather conditions. This part cross-references Beck/Arnley 101-6994 and MOOG Chassis Products K201491 for the same application.
Common Repair Symptoms
- Rear suspension clunking or rattling over bumps
- Excessive sway bar movement at the rear axle
- Worn, cracked, or flattened stabilizer bar bushings
- Loose-feeling rear suspension response
- Noise from the rear stabilizer bar mounting area
Installation Notes and Tips
Confirm rear fitment by matching the vehicle year, model, and stabilizer bar dimensions before installation. Inspect the sway bar, brackets, and surrounding suspension components for wear or corrosion so the new bushing seats correctly. Clean the mounting surfaces and verify the bushing orientation against the original part during service.
Quality Assurance
Delphi uses OE-focused engineering practices and durability testing for its aftermarket steering and suspension portfolio. TD1482W is built as a standard replacement part with attention to fit, material consistency, and environmental resistance for rear suspension service on the Honda CR-V.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 2001 | Honda | CR-V | Rear | — |
| 2000 | Honda | CR-V | Rear | — |
| 1999 | Honda | CR-V | Rear | — |
| 1998 | Honda | CR-V | Rear | — |
| 1997 | Honda | CR-V | Rear | — |
| No rows match your filter. | ||||