Delphi TD1973W Suspension Stabilizer Bar Bushing Kit - Front
OE Quality 60-Day Returns
Delphi

Delphi TD1973W Suspension Stabilizer Bar Bushing Kit - Front

Brand Delphi TD1973W
Position Front
Material Rubber
Color Black
Inside Diameter 0.85
Inside Diameter 21.5
Grease Fitting Included No
Width 2.14
Width 54.4
Mounting Hardware Included No
Height 2.34
Height 59.4
Fits BMW · 6 vehicles

OE expertise. Delphi applies original-equipment know-how to aftermarket steering parts.

Rubber construction. Black bushing kit built for dependable suspension isolation.

Extreme testing. Withstands temperatures below -40 C and over 120 C.

Cross-references 31 30 3 404 065 and BSK14180 for the same application. See all 2.

$26.27Free shipping
In stock · usually ships same day before 1pm CST
Step 1 — Confirm fitment
Free return shipping if it doesn't fit when you check fitment here first.

Select your vehicle to confirm fitment
Verify this part fits before purchasing β€” free returns if it doesn't
Step 2 — Quantity
Order total $26.27
Free shipping to the continental U.S.
Free returns within 60 days if it doesn't fit when fitment is verified.
Not what you need? See all Suspension Stabilizer Bar Bushing Kit options

Delphi Front Stabilizer Bar Bushing Kit

Restore front suspension control with the Delphi TD1973W stabilizer bar bushing kit. Built with rubber construction and OE-focused dimensional analysis, this front sway bar bushing is made for precise fitment on select BMW applications, including the BMW X3.

  • Rubber bushing material for suspension isolation and bar support
  • Black finish
  • Front position application
  • Inside diameter: 0.85 in. / 21.5 mm
  • Width: 2.14 in. / 54.4 mm
  • Height: 2.34 in. / 59.4 mm
  • No grease fitting included
  • No mounting hardware included

OE-Style Fit and Function

The Delphi TD1973W is a suspension stabilizer bar bushing kit engineered for front sway bar service where accurate sizing matters. Delphi applies OE-level material and dimensional analysis to help maintain proper bar location and suspension response, and the part is tested for temperature extremes and salt-spray exposure to support durability in demanding road conditions. This part cross-references BMW OE number 31 30 3 404 065 and BSK14180 for the same application.

Fits 2004-2009 BMW X3, front with 21.8mm bar diameter. This Delphi TD1973W bushing kit is a direct-fit front suspension service part for BMW X3 models in the listed range.

Common Repair Uses

  • Front sway bar movement caused by worn rubber bushings
  • Clunking or rattling from the front suspension area
  • Excessive play at the stabilizer bar mounting point
  • Reduced steering stability from deteriorated bushing material
  • Noise from dry, cracked, or compressed front stabilizer bushings

Installation Notes

Verify the front stabilizer bar diameter before installation; this application is listed for a 21.8 mm bar diameter. Inspect the sway bar and mounting surfaces for wear, corrosion, or deformation before fitting the new bushing. Because mounting hardware is not included, reuse or replace related fasteners as needed during service.

Quality Assurance

Delphi uses OE-based engineering practices for its aftermarket steering and suspension components. The TD1973W is evaluated for temperature resistance below -40 degrees C and above 120 degrees C, and it is exposed to 720 hours of salt spray testing to help confirm material durability and corrosion resistance.

Related reading

This part fits 6 vehicles
Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
YearMakeModelPositionNotes
2009BMWX3Frontwith 21.8mm Bar Diameter
2008BMWX3Frontwith 21.8mm Bar Diameter
2007BMWX3Frontwith 21.8mm Bar Diameter
2006BMWX3Frontwith 21.8mm Bar Diameter
2005BMWX3Frontwith 21.8mm Bar Diameter
2004BMWX3Frontwith 21.8mm Bar Diameter
Directly replaces or cross-references 2 part numbers
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.
31 30 3 404 065BSK14180