HomeDelphi TD1994W Suspension Control Arm Bushing - Rear Lower At Knuckle
Part #: TD1994W

Delphi TD1994W Suspension Control Arm Bushing - Rear Lower At Knuckle

Rear Lower At Knuckle
⚙️ 6 vehicles fit this part
🔍
Select your vehicle to confirm fitment
Verify this part fits before purchasing — free returns if it doesn't
$23.07Free Shipping
🚚Free ShippingNo Cost to Continental U.S.
🔄Free Returns*Wrong fit? No cost
🛡️60-Day ReturnsMoney back guarantee
*Free return shipping only qualifies if our fitment verification tool is used.
🔥
✅ In Stock · Ready To Ship Most orders ship same-day if ordered before 1pm CST.
OE Direct Replacement — Bolt-on fit, no modifications needed
🚗Fitment: Honda, CR-V and Element
🔄Easy Returns — Return within 60 days for a full refund
🚚Fast Shipping — Most orders ship same business day before 1pm CST

Delphi Rear Lower Control Arm Bushing

Delphi TD1994W is a premium suspension control arm bushing built for the rear lower at knuckle position. It uses natural rubber construction and OE-equal dimensions to support precise suspension movement on select Honda applications, including the CR-V and Element.

  • Natural rubber bushing material for controlled suspension compliance
  • Premium-grade, press-fit design
  • Black finish
  • OEM-equal dimensions for fit consistency
  • Greaseable: No
  • Hardware included: No
  • Position: Rear lower at knuckle

Application Details

Compatible with 2005-2006 Honda CR-V, rear lower at knuckle, and 2003-2006 Honda Element, rear lower at knuckle. Delphi TD1994W is engineered for the rear suspension control arm interface where the bushing helps isolate road vibration while maintaining alignment and suspension geometry. This part cross-references Monroe Shocks & Struts (e.g., 172286, 182286) for the same application.

What It Helps Address

  • Rear suspension clunking or knocking from worn rubber
  • Excessive play at the control arm knuckle connection
  • Uneven tire wear related to suspension looseness
  • Vibration transfer through the rear suspension
  • Alignment instability caused by deteriorated bushings

Installation Notes

TD1994W uses a press-fit mounting type and is intended for the rear lower at knuckle location. Inspect the control arm, knuckle interface, and surrounding hardware before installation, and verify dimensions against the original bushing for proper seating. Professional installation and a post-repair alignment are recommended after suspension service on Honda CR-V and Honda Element models.

Quality Assurance

Delphi applies OE-focused dimensional and material analysis to its aftermarket steering and suspension portfolio. This bushing is tested for extreme temperature exposure from below -40 degrees C to over 120 degrees C and for 720 hours of salt spray to help verify durability under demanding conditions.

BrandDelphi
Part NumberTD1994W
MaterialNatural rubber
10151Oem equal
Wall Thickness0.807
Wall Thickness20.50
Bushing ColorBlack
Length1.823
Length46.30
ColorBlack
Inside Diameter0.484
Inside Diameter12.30
Width2.094
Width53.20
Outside Diameter2.094
Outside Diameter53.20
Mounting Hardware IncludedNo
Height2.094
Height53.20
Grade TypePremium
GreaseableNo
Steering TypePower
Bushing MaterialRubber
Mounting Hole Diameter12.30
Mounting TypePress fit
Color CodeBk
Hardware IncludedNo
Position(s)Rear lower at knuckle

This part fits 6 vehicles. Search below:

YearMakeModelPositionNotes
2006HondaCR-VRear Lower At Knuckle
2006HondaElementRear Lower At Knuckle
2005HondaCR-VRear Lower At Knuckle
2005HondaElementRear Lower At Knuckle
2004HondaElementRear Lower At Knuckle
2003HondaElementRear Lower At Knuckle

* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.

This part directly replaces or is cross-referenced with the following part numbers:

52365-S5A-02452365-S5A-80152365-S5A-80252365-SCV-A01

Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.