Delphi TD4111W Suspension Stabilizer Bar Bushing Kit - Front To Frame

Delphi TD4111W Front Sway Bar Bushing Kit

Restore front stabilizer bar support with the Delphi TD4111W suspension stabilizer bar bushing kit. This standard replacement rubber bushing is built for front-to-frame mounting and is sized for vehicles using a 1-5/16 in. diameter sway bar.

Delphi applies OE-focused engineering to its aftermarket steering and suspension portfolio, with dimensional and material analysis used to match OE fit and function. The TD4111W is a practical replacement for worn front sway bar bushings on applications such as Chevrolet Camaro, Pontiac Firebird, and GMC Jimmy.

Key Features

• Rubber construction for front stabilizer bar mounting
• Inside diameter: 1.338 in.
• Standard replacement grade
• Front to frame position
• Fits vehicles with a 1-5/16 in. diameter sway bar
• Delphi part number TD4111W

Fitment and Application

Compatible with a wide range of GM rear-wheel-drive and truck platforms from 1973-2005, including front-to-frame applications on Chevrolet Camaro, Pontiac Firebird, GMC Jimmy, and Chevrolet S10 models. The Delphi TD4111W is also listed for Buick Regal, Oldsmobile Cutlass Supreme, Pontiac Grand Prix, and GMC Yukon applications that use the specified sway bar diameter.

• Fits 1992-2005 GMC Jimmy, Front To Frame
• Fits 1986-2002 Chevrolet Camaro, Front To Frame
• Fits 1986-2002 Pontiac Firebird, Front To Frame
• Fits 1990-2001 Chevrolet Lumina, Front To Frame
• Fits 1999-2000 Cadillac Escalade, Front To Frame
• Fits 1992-2000 GMC Yukon, Front To Frame
• Fits 1995-1999 Chevrolet Monte Carlo, Front To Frame
• Fits 1978-1988 Chevrolet Monte Carlo, Front To Frame
• Fits 1978-1997 Oldsmobile Cutlass Supreme, Front To Frame
• Fits 1978-1996 Buick Regal, Front To Frame
• Fits 1973-1996 Pontiac Grand Prix, Front To Frame
• Fits 1992-1994 Chevrolet Blazer, Front To Frame
• Fits 1983-1994 Chevrolet S10, Front To Frame
• Fits 1983-1994 Chevrolet S10 Blazer, Front To Frame
• Fits 1991-1994 GMC Sonoma, Front To Frame
• Fits 1991-1994 Oldsmobile Bravada, Front To Frame
• Fits 1990-1993 Oldsmobile Cutlass Cruiser, Front To Frame
• Fits 1980-1992 Oldsmobile Custom Cruiser, Front To Frame
• Fits 1983-1991 GMC S15 Jimmy, Front To Frame
• Fits 1983-1990 GMC S15, Front To Frame
• Fits 1985-1987 Oldsmobile Cutlass, Front To Frame
• Fits 1978-1981 Oldsmobile Cutlass, Front To Frame
• Fits 1985-1987 Oldsmobile Cutlass Salon, Front To Frame
• Fits 1980-1985 Buick LeSabre, Front To Frame
• Fits 1978-1984 Oldsmobile Cutlass Calais, Front To Frame
• Fits 1982 Pontiac Grand LeMans, Front To Frame
• Fits 1978-1980 Oldsmobile Cutlass Salon, Front To Frame

What This Part Helps Address

• Clunking or knocking from the front sway bar area
• Excessive sway bar movement at the frame mount
• Worn, cracked, or compressed rubber bushings
• Loose-feeling front suspension response during cornering
• Noise caused by deteriorated stabilizer bar support

Installation Notes and Tips

Confirm sway bar diameter before ordering, since this bushing kit is specified for 1-5/16 in. bars. Verify the vehicle’s front-to-frame mounting location and compare the original bushing dimensions to the TD4111W inside diameter for proper fit.

For cross-reference, this part matches Dorman OE Solutions 535-787 and MOOG Chassis Products K6457 for the same application.

Quality Assurance

Delphi subjects its OE-style components to temperature extremes below -40 degrees C and above 120 degrees C, along with extended salt-spray exposure and dimensional/material analysis to support consistent fit and durability expectations.