Delphi TD760W Suspension Control Arm Bushing - Rear Upper Inner

Delphi TD760W Rear Upper Inner Bushing

Delphi TD760W is a suspension control arm bushing built for rear upper inner locations on select BMW applications. It uses a rubber-aluminum construction and press-fit mounting to match OE-style dimensions and fitment requirements for BMW 3 Series, X3, and Z4 suspension service.

For BMW 325i, 330i, M3, and Z4 rear suspension repairs, this bushing is specified as a standard replacement that follows Delphi’s OE-focused dimensional and material analysis. The TD760W part number is also commonly searched as a direct replacement reference for rear upper inner control arm service.

Key Features

• Suspension control arm bushing for rear upper inner position
• Rubber-aluminum material construction
• Press-fit mounting type for OE-style installation
• Standard replacement grade for routine suspension repair
• Dimensions: 66.5 mm length, 66.4 mm height, 35.3 mm outside diameter, 12.2 mm inside diameter
• Delphi TD760W fitment for BMW rear suspension applications

Detailed Description

Delphi TD760W is engineered for rear upper inner control arm locations where precise bushing geometry matters for suspension alignment and ride control. Delphi applies OE-level dimensional and material analysis to help ensure proper compatibility between the original part and the aftermarket replacement. The rubber-aluminum design supports the suspension mounting point while maintaining the correct press-fit interface for service on BMW chassis platforms.

Compatible With BMW 325Ci, 330Ci, 330xi, M3, 320i, 325i, 325xi, 330i, 323Ci, 323i, 328Ci, 328i, 318i, 318is, 318ti, 323is, and 328is rear upper inner applications. This part cross-references MOOG Chassis Products K200091 for the same application.

What It Helps Repair

• Rear suspension looseness or excess movement at the control arm pivot
• Clunking or knocking from worn rear upper inner bushing points
• Uneven tire wear caused by degraded rear suspension geometry
• Imprecise rear-end handling from worn rubber support
• Inspection failures related to deteriorated suspension bushings

Installation Notes and Tips

TD760W installs as a press-fit suspension bushing and should be matched to the exact rear upper inner position listed in the fitment data. Proper removal and installation tools are recommended to avoid damaging the control arm or the new bushing. Verify the vehicle application by year, model, and suspension position before service. Fits 2003-2016 BMW Z4, rear upper inner; Fits 2004-2010 BMW X3, rear upper inner; Fits 2001-2006 BMW 325Ci, rear upper inner; Fits 2001-2006 BMW 330Ci, rear upper inner; Fits 2001-2006 BMW 330xi, rear upper inner; Fits 2001-2006 BMW M3, rear upper inner; Fits 1995-1999 BMW M3, rear upper inner; Fits 2001-2005 BMW 320i, rear upper inner; Fits 1992-1995 BMW 320i, rear upper inner; Fits 2001-2005 BMW 325i, rear upper inner; Fits 1992-1995 BMW 325i, rear upper inner; Fits 2001-2005 BMW 325xi, rear upper inner; Fits 2001-2005 BMW 330i, rear upper inner; Fits 2000 BMW 323Ci, rear upper inner; Fits 1998-2000 BMW 323i, rear upper inner; Fits 2000 BMW 328Ci, rear upper inner; Fits 1996-2000 BMW 328i, rear upper inner; Fits 1992-1999 BMW 318i, rear upper inner; Fits 1991-1999 BMW 318is, rear upper inner; Fits 1995-1999 BMW 318ti, rear upper inner; Fits 1998-1999 BMW 323is, rear upper inner; Fits 1996-1999 BMW 328is, rear upper inner; Fits 1992-1995 BMW 325is, rear upper inner.

Quality Assurance

Delphi tests steering and suspension components across extreme temperature and corrosion conditions, including sub-zero cold, high heat, and extended salt-spray exposure. That OE-focused validation supports consistent fit and material performance for BMW rear suspension service.