Delphi TS10562 Air Charge Temperature Sensor

Delphi TS10562 Air Charge Temperature Sensor

Delphi TS10562 is an OE-style air charge temperature sensor built for accurate intake air temperature readings in Ford and Lincoln applications. It is a direct replacement for a wide range of vehicles, including the Ford F-150, Ford Ranger, and Lincoln Town Car, with calibration and validation aligned to OE standards.

Key Features

• Air charge temperature sensor for engine management systems
• OE-standard testing and calibration for accurate signal output
• 5-volt sensor with 2-pin male connector and square connector shape
• PA66 housing with grey finish for standard replacement use
• Mounting hardware included for installation convenience
• Operating temperature range: -40 to 110 degrees C
• Delphi TS10562 cross-references Denso 210-1017 and Standard Ignition AX25

Detailed Description

The Delphi TS10562 air charge temperature sensor measures incoming air temperature so the engine control module can adjust fuel delivery and ignition strategy. Delphi validates and calibrates its sensors to OE standards, helping maintain consistent readings across Ford, Mercury, and Lincoln platforms. This part number is used across applications such as the 1999-2003 Ford F-150, 1998-2001 Ford Ranger, and 1995-2005 Lincoln Town Car, making Delphi TS10562 a practical OE replacement for common drivability and sensor fault repairs.

Compatible vehicle coverage includes long-tail search applications such as air charge temperature sensor replacement for 1999-2003 Ford F-150, intake air temperature sensor for 1998-2001 Ford Ranger, and Delphi TS10562 for 1995-2005 Lincoln Town Car. It also serves Ford Crown Victoria, Mercury Grand Marquis, Ford Windstar, and related models listed in the fitment data.

Common Issues This Part Can Address

• Incorrect intake air temperature readings
• Check engine light related to air charge temperature sensor faults
• Rough idle or drivability concerns caused by inaccurate sensor input
• Fuel mixture or timing corrections triggered by bad temperature data
• Hard starting or inconsistent engine response in affected applications

Installation Notes and Tips

Verify connector style, terminal count, and mounting location before installation. The Delphi TS10562 uses a square 1-connector, 2-terminal male configuration with pin terminals and includes mounting hardware. Inspect the harness connector for corrosion or damaged terminals, and clear diagnostic trouble codes after replacement if required by the vehicle.

Quality Assurance

Delphi sensors are developed and validated using OE-focused methods, with testing and calibration performed to support accurate readings and reduce repeat repairs. The PA66 housing and standard replacement design support dependable service in the listed Ford, Mercury, and Lincoln applications.

• Fits 1995-2005 Lincoln Town Car, N/A
• Fits 2004 Ford F-150 Heritage, N/A
• Fits 1999-2003 Ford E-350 Super Duty, N/A
• Fits 2000-2003 Ford Excursion, N/A
• Fits 1999-2003 Ford F-150, N/A
• Fits 1999-2003 Ford F-250 Super Duty, N/A
• Fits 1999-2003 Ford F-350 Super Duty, N/A
• Fits 1995-2002 Ford Crown Victoria, N/A
• Fits 1997-2002 Ford E-350 Econoline Club Wagon, N/A
• Fits 1995-2002 Mercury Grand Marquis, N/A
• Fits 1998-2001 Ford Ranger, N/A
• Fits 2001 Mercury Cougar, N/A
• Fits 1996-1997 Mercury Cougar, N/A
• Fits 1996-2000 Ford Contour, N/A
• Fits 1995-2000 Ford Windstar, N/A
• Fits 1996-2000 Mercury Mystique, N/A
• Fits 1996-1999 Ford Taurus, N/A
• Fits 1996-1999 Mercury Sable, N/A
• Fits 1997-1998 Ford E-350 Econoline, N/A
• Fits 1997 Ford F-250 HD, N/A
• Fits 1995-1997 Ford F-350, N/A
• Fits 1996-1997 Ford Thunderbird, N/A
• Fits 1995-1996 Ford F-250, N/A