/live/media/RB/RB_919042_Zz3.jpg)
OE Quality
60-Day Returns
Dorman 919-042 Brake Hydraulic Line
Dorman 919-042 Brake Hydraulic Line Kit
Dorman 919-042 is a pre-formed brake hydraulic line kit built from stainless steel for corrosion resistance. It is made for 2001-2005 Ford Ranger applications and follows the OE-style routing needed for a cleaner, more direct replacement.
- Stainless steel line material helps resist rust in brake system service
- Pre-formed shape supports easier routing on the vehicle
- Performance grade replacement for brake hydraulic repair
- Inverted fitting type with inverted and bubble flare ends
- Brake line size: 0.189 in; hose/line maximum pressure: 4000 PSI
- Fits 2001-2005 Ford Ranger
Detailed Product Overview
This brake hydraulic line kit is built for the Ford Ranger brake system where the original line has corroded, leaked, or become difficult to service. The stainless steel construction helps address the rust-prone nature of factory brake lines, while the pre-formed design follows the intended vehicle application for a more direct replacement. Part number 919-042 is also a practical OE-style solution for technicians and DIY repairs that need accurate line routing and proper flare and fitting configuration.
This part cross-references Monroe Shocks & Struts (e.g., CBK0077SS) for the same application.
Common Problems This Part Can Address
- Brake fluid seepage from a rusted or damaged hydraulic line
- Corrosion on the original Ford Ranger brake line routing
- Difficulty matching the factory line shape during repair
- Brake service delays caused by seized or deteriorated line fittings
- Pressure loss in a compromised brake hydraulic circuit
Installation Notes and Tips
Verify the vehicle year and brake line routing before installation. This line is pre-formed, so compare the bends, flare style, and fitting thread diameter to the removed part before final tightening. Use proper brake service procedures, bleed the system after installation, and inspect all connections for leaks.
Quality Assurance
Dorman OE FIX brake hydraulic line kits use upgraded stainless steel construction to improve corrosion resistance versus common rust-prone original lines. Part number 919-042 is built as a standard replacement for the listed Ford Ranger applications.
| Brand | Dorman |
|---|---|
| Part Number | 919-042 |
| Inside Diameter | 1.86 |
| Outside Diameter | 5.07 |
| Grade Type | Performance |
| Grade Type | Rendimiento |
| Fitting Type | Inverted |
| Fitting Type | Invertido |
| Bendable | Oui |
| Bendable | Sí |
| Bendable | Yes |
| End 1 Flare Type | Inverted |
| End 1 Flare Type | Invertido |
| End 2 Flare Type | Bubble |
| End 2 Flare Type | Burbuja |
| Fitting Finish | Acero inoxidable |
| Fitting Finish | Stainless steel |
| Fitting Material | Acero inoxidable |
| Fitting Material | Stainless steel |
| Polyvinyl Fluoride Coated | No |
| Polyvinyl Fluoride Coated | Non |
| Line Diameter | 4.80 |
| Line Length | 4.762 |
| Line Material | Acero inoxidable |
| Line Material | Stainless steel |
| Outer Spring | No |
| Outer Spring | Non |
| Outer Wear Guard | No |
| Outer Wear Guard | Non |
| Pre-Formed | Oui |
| Pre-Formed | Sí |
| Pre-Formed | Yes |
This part fits 5 vehicles. Search below:
| Year | Make | Model | Body Type | Drive Type | Position | Notes |
|---|---|---|---|---|---|---|
| 2005 | Ford | Ranger | Extended Cab Pickup | 4WD | N/A | |
| 2004 | Ford | Ranger | Extended Cab Pickup | 4WD | N/A | |
| 2003 | Ford | Ranger | Extended Cab Pickup | 4WD | N/A | |
| 2002 | Ford | Ranger | Extended Cab Pickup | 4WD | N/A | |
| 2001 | Ford | Ranger | Extended Cab Pickup | 4WD | N/A |
* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
This part directly replaces or is cross-referenced with the following part numbers:
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.