/live/media/RB/RB_966507_FRO.JPG)
Dorman 966-507 Drive Shaft - Rear
| Brand | Dorman 966-507 |
|---|---|
| Position | Rear |
| Compressed Length | 100.25 |
| 10919 | Oui |
| 10919 | Sí |
| 10919 | Yes |
| 10920 | Oui |
| 10920 | Sí |
| 10920 | Yes |
| Wall Thickness | 0.083 |
| 11432 | 2 |
| End 1 Type | Bolt on |
| End 1 Type | Con perno |
| End 2 Type | Bolt on |
| End 2 Type | Con perno |
| Shaft Material | Acero |
| Shaft Material | Steel |
| Pre-Greased | Oui |
| Pre-Greased | Sí |
| Pre-Greased | Yes |
| Grease Fitting Included | Oui |
| Grease Fitting Included | Sí |
| Grease Fitting Included | Yes |
| Universal Joints Included | Oui |
| Universal Joints Included | Sí |
| Universal Joints Included | Yes |
| CV Joints Included | No |
| CV Joints Included | Non |
| Axle Nut Included | No |
| Axle Nut Included | Non |
| Grade Type | Reemplazo estándar |
| Grade Type | Standard replacement |
| Fits | Toyota · 3 vehicles |
Complete assembly. Includes new yokes, tubes, CV joints, and universal joints for a full driveline replacement.
Pre-balanced design. Helps reduce vibration and supports smoother operation after installation.
Steel construction. Standard replacement shaft with bolt-on ends, slip yoke, and pre-greased components.
Cross-references 371000C180 and 371000C184 for the same application. See all 2.
Overview
This Dorman drive shaft assembly is a complete replacement for rear driveline service on the Toyota Tundra. Part number 966-507 is pre-balanced and built with new yokes, tubes, CV joints, and universal joints for a straightforward driveline repair.
Key Features
- Complete drive shaft assembly for direct driveline replacement
- Pre-balanced for smoother operation after installation
- 100% new yokes, tubes, CV joints, and universal joints
- Steel shaft construction with standard replacement grade
- Slip yoke design with bolt-on end connections
- Pre-greased and includes a grease fitting
Detailed Description
Built for rear driveline service, this Dorman drive shaft is engineered as a complete assembly rather than a partial repair. The steel shaft measures 101.25 inches in drive shaft length with a 0.083-inch wall thickness, and the assembly is phased at 90 degrees for proper driveline alignment. It also uses bolt-on end types and a slip yoke with 1 inch of max slip, which supports fitment where that configuration is required. For Toyota Tundra applications, part number 966-507 provides a standard replacement solution that reduces the need to rebuild individual driveline components.
This part cross-references Toyota 371000C180 and 371000C184 for the same application.
What It Helps Fix
- Vibration caused by worn or out-of-balance driveline components
- Noise from worn universal joints or CV joints
- Driveline play related to damaged yokes or shaft wear
- Service issues from a bent or fatigued drive shaft assembly
Installation Notes
Compatible With 2007-2009 Toyota Tundra, rear. Verify compressed length, flange-to-flange length, and end connection type before installation. This assembly is pre-greased and ready to install, and the bolt-on ends support a direct replacement process where the original configuration matches.
Quality Assurance
Dorman supplies this drive shaft as a standard replacement assembly with new major driveline components already installed. Part number 966-507 is built for applications that require a complete rear drive shaft replacement rather than component-level rebuilding.
| Year | Make | Model | Body Type | Bed Length | Drive Type | Liters | Cylinders | Wheel Base | Position | Notes |
|---|---|---|---|---|---|---|---|---|---|---|
| 2009 | Toyota | Tundra | Extended Cab Pickup | 8' 1" Foot Bed | 4WD | 4.7L | V8 | 164.6" | Rear | — |
| 2008 | Toyota | Tundra | Extended Cab Pickup | 8' 1" Foot Bed | 4WD | 4.7L | V8 | 164.6" | Rear | — |
| 2007 | Toyota | Tundra | Extended Cab Pickup | 8' 1" Foot Bed | 4WD | 4.7L | V8 | 164.6" | Rear | — |
| No rows match your filter. | ||||||||||