/live/media/RB/RB_986600_Fro.jpg)
OE Quality
60-Day Returns
Dorman 986-600 Drive Shaft - Rear
Dorman 986-600 Drive Shaft for BMW 550i
Restore driveline performance with this Dorman drive shaft assembly for the rear of the 2011 BMW 550i, to 9/11. Part number 986-600 is a complete replacement assembly that arrives pre-balanced and ready to install, with new yokes, tubes, constant velocity joints, and universal joints where applicable to the design.
Key Features
- Complete drive shaft assembly for rear driveline service
- Pre-balanced for smoother operation after replacement
- 100% new yokes and tubes
- Universal joints included
- Steel shaft construction
- Bolt-on end 1 and bolt-on end 2
- Compressed length: 60.25 in.
- Shaft diameter: 2.5 in.
- Wall thickness: 0.083 in.
- Standard replacement grade
Detailed Description
Dorman 986-600 is built for direct replacement of the rear drive shaft on the 2011 BMW 550i, to 9/11. The assembly is pre-balanced to reduce the need for additional setup, and its steel construction supports dependable driveline service. With bolt-on connections at both ends and a fixed overall length of 60.25 inches, this BMW 550i drive shaft is specified for a straightforward replacement on the listed application.
This part cross-references BMW OE part number 26107610358 for the same application. Search terms such as 2011 BMW 550i rear drive shaft replacement, BMW 550i rear driveshaft assembly, and Dorman 986-600 BMW driveline part can help confirm the correct listing for your vehicle.
What It Helps Address
- Driveline vibration from a worn or out-of-balance shaft
- Clunking or driveline noise during acceleration or deceleration
- Excess play from worn joints or shaft components
- Service issues caused by a damaged or corroded drive shaft
- Replacement needs after driveline wear on the rear BMW 550i application
Installation Notes and Tips
Verify rear fitment on the 2011 BMW 550i and confirm the 60.25-inch compressed length, bolt-on ends, and listed application before installation. Inspect mating flanges, fasteners, and surrounding driveline components for wear or damage before mounting the new assembly. Because this shaft is pre-balanced, avoid altering the assembly before installation.
Quality Assurance
Dorman supplies this drive shaft as a standard replacement assembly with new core components and pre-balanced construction for the listed BMW application. Part number 986-600 is engineered to match the specified driveline configuration for the 2011 BMW 550i, rear, to 9/11.
| Brand | Dorman |
|---|---|
| Part Number | 986-600 |
| Compressed Length | 60.25 |
| 10920 | No |
| 10920 | Non |
| End 1 Type | Bolt on |
| End 1 Type | Con perno |
| End 2 Type | Bolt on |
| End 2 Type | Con perno |
| Shaft Material | Acero |
| Shaft Material | Steel |
| Universal Joints Included | Oui |
| Universal Joints Included | Sí |
| Universal Joints Included | Yes |
| CV Joints Included | No |
| CV Joints Included | Non |
| Axle Nut Included | No |
| Axle Nut Included | Non |
| Grade Type | Reemplazo estándar |
| Grade Type | Standard replacement |
| Shaft Diameter | 2.5 |
| Slip Yoke | No |
| Slip Yoke | Non |
| Drive Shaft Length (In) | 60.25 in |
| Drive Shaft Length (In) | 60.25 in. |
| Drive Shaft Wall Thickness (In) | 0.083 in |
| Drive Shaft Wall Thickness (In) | 0.083 in. |
| Espesor de la pared del eje motriz (in) | 0.083 in. |
| Longitud del eje motriz (in) | 60.25 in. |
| Longitud total ajustable | No |
| Overall Length Adjustable | No |
| Overall Length Adjustable | Non |
This part fits 1 vehicles. Search below:
| Year | Make | Model | Drive Type | Transmission | Position | Notes |
|---|---|---|---|---|---|---|
| 2011 | BMW | 550i | RWD | Manual | Rear | To 9/11 |
* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
This part directly replaces or is cross-referenced with the following part numbers:
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.