/live/media/RB/RB_986750_Fro.jpg)
OE Quality
60-Day Returns
Dorman 986-750 Drive Shaft - Rear
BMW 535i GT Rear Drive Shaft Assembly
This Dorman drive shaft assembly is built for rear applications on the 2014-2017 BMW 535i GT. Part number 986-750 is a complete replacement solution with pre-balanced construction and new yokes, tubes, CV joints, and universal joints for a direct driveline service repair.
Key Features
- Complete drive shaft assembly for rear installation
- Pre-balanced for smoother driveline operation
- 100% new yokes, tubes, constant velocity joints, and universal joints
- Steel shaft construction with a 2.5 in. shaft diameter
- Pre-greased and ready for installation
- Standard replacement grade for OE-style service
- Compressed length: 65 in.; drive shaft length: 66 in.
- Phasing: 0 degrees; max slip: 1 in.
Detailed Description
Dorman 986-750 is a rear drive shaft assembly for the 2014-2017 BMW 535i GT. It uses a bolt-on end at one side and a splined end at the other, with steel shaft construction and a multi-piece design. The assembly is pre-greased, includes CV joints and universal joints, and arrives pre-balanced to support a smoother driveline replacement. This part cross-references BMW OE numbers 26108626667 and 26108693397 for the same application.
For BMW 535i GT rear driveline service, this part number 986-750 provides a direct replacement option when the original shaft is worn, noisy, or out of balance. It is listed for 2014, 2015, 2016, and 2017 BMW 535i GT rear applications.
Common Problems This Part Can Address
- Driveline vibration at speed
- Clunking or knocking from the rear shaft area
- Worn CV joint or universal joint noise
- Excessive play in the driveshaft assembly
- Failure from a damaged or unbalanced shaft
Installation Notes and Tips
Verify rear fitment on the 2014-2017 BMW 535i GT before installation. Confirm flange and spline engagement, and inspect surrounding driveline components for wear that could affect the new shaft. Because the assembly is pre-balanced and pre-greased, it is ready for installation without additional balancing steps.
Quality Assurance
Dorman supplies this drive shaft as a standard replacement assembly built with new yokes, tubes, CV joints, and universal joints. The pre-balanced design supports consistent driveline service on BMW 535i GT rear applications.
| Brand | Dorman |
|---|---|
| Part Number | 986-750 |
| Compressed Length | 65 |
| 10920 | No |
| 10920 | Non |
| End 1 Type | Bolt on |
| End 1 Type | Con perno |
| End 2 Type | Estriado |
| End 2 Type | Splined |
| Shaft Material | Acero |
| Shaft Material | Steel |
| Pre-Greased | Oui |
| Pre-Greased | Sí |
| Pre-Greased | Yes |
| Grease Fitting Included | No |
| Grease Fitting Included | Non |
| Universal Joints Included | Oui |
| Universal Joints Included | Sí |
| Universal Joints Included | Yes |
| CV Joints Included | Oui |
| CV Joints Included | Sí |
| CV Joints Included | Yes |
| Axle Nut Included | No |
| Axle Nut Included | Non |
| Grade Type | Reemplazo estándar |
| Grade Type | Standard replacement |
| Shaft Diameter | 2.5 |
| Slip Yoke | No |
| Slip Yoke | Non |
| Max Slip | 1 |
| Max Slip | 1 in |
| Phase Degrees | 0 |
This part fits 4 vehicles. Search below:
| Year | Make | Model | Drive Type | Position | Notes |
|---|---|---|---|---|---|
| 2017 | BMW | 535i GT | RWD | Rear | |
| 2016 | BMW | 535i GT | RWD | Rear | |
| 2015 | BMW | 535i GT | RWD | Rear | |
| 2014 | BMW | 535i GT | RWD | Rear |
* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
This part directly replaces or is cross-referenced with the following part numbers:
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.