/live/media/RB/RB_986934_Fro.jpg)
OE Quality
60-Day Returns
Dorman 986-934 Drive Shaft - Rear
Complete Rear Drive Shaft for 2010 Toyota Tundra
This Dorman drive shaft assembly is built for the rear of the 2010 Toyota Tundra and arrives pre-balanced for installation. Part number 986-934 includes new yokes, tubes, universal joints, and a service-ready layout for a direct driveline replacement.
Key Features
- Fits 2010 Toyota Tundra, rear, from 3/10
- Complete drive shaft assembly with 100% new yokes, tubes, and universal joints
- Pre-balanced for smoother driveline operation after installation
- Steel shaft construction with 4 in. shaft diameter
- Slip yoke end 1 and bolt-on end 2 for the specified application
- Pre-greased and phased at 90 degrees
- Compressed length: 114.5 in.; wall thickness: 0.083 in.
- Standard replacement grade for OE-style driveline service
Detailed Description
Dorman 986-934 is a complete rear drive shaft assembly for the 2010 Toyota Tundra, built for vehicles noted from 3/10. It is supplied pre-balanced and uses new steel tubes, new yokes, and new universal joints to replace a worn or damaged driveline section without rebuilding the original shaft. The assembly measures 114.5 inches in overall length, uses a slip yoke at one end and a bolt-on connection at the other, and is phased at 90 degrees for the listed application. This part cross-references Toyota OE numbers 371000C202 and 371000C204 for the same application.
Common Problems This Part Can Address
- Driveline vibration caused by a worn or out-of-balance shaft
- Clunking or driveline noise from worn universal joints
- Damage to the original shaft tubes or yokes
- Excess play in the rear driveline assembly
- Service issues tied to a bent or fatigued drive shaft
Installation Notes and Tips
Verify the rear application, compressed length, and end types before installation on the 2010 Toyota Tundra. Confirm the vehicle build date of 3/10 or later, and inspect mating surfaces, flange condition, and driveline alignment during replacement. Because this is a complete assembly, it is intended to replace the existing shaft rather than be rebuilt in place.
Quality Assurance
Dorman supplies this drive shaft as a standard replacement part with new major components and pre-balanced assembly preparation. Part number 986-934 is built to match the listed fitment and driveline configuration for the rear of the 2010 Toyota Tundra.
| Brand | Dorman |
|---|---|
| Part Number | 986-934 |
| Compressed Length | 114.5 |
| 10920 | No |
| 10920 | Non |
| End 1 Type | Slip yoke |
| End 1 Type | Yugo deslizante |
| End 2 Type | Bolt on |
| End 2 Type | Con perno |
| Shaft Material | Acero |
| Shaft Material | Steel |
| Pre-Greased | Oui |
| Pre-Greased | Sí |
| Pre-Greased | Yes |
| Grease Fitting Included | No |
| Grease Fitting Included | Non |
| Universal Joints Included | Oui |
| Universal Joints Included | Sí |
| Universal Joints Included | Yes |
| CV Joints Included | No |
| CV Joints Included | Non |
| Axle Nut Included | No |
| Axle Nut Included | Non |
| Grade Type | Reemplazo estándar |
| Grade Type | Standard replacement |
| Shaft Diameter | 4 |
| Slip Yoke | Oui |
| Slip Yoke | Sí |
| Slip Yoke | Yes |
| Phase Degrees | 90 |
| Phased | Oui |
| Phased | Sí |
This part fits 1 vehicles. Search below:
| Year | Make | Model | Body Type | Bed Length | Drive Type | Liters | Cylinders | Wheel Base | Position | Notes |
|---|---|---|---|---|---|---|---|---|---|---|
| 2010 | Toyota | Tundra | Extended Cab Pickup | 8' 1" Foot Bed | RWD | 4.6L | V8 | 164.6" | Rear | From 3/10 |
* Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
This part directly replaces or is cross-referenced with the following part numbers:
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.