Global Parts 1813484 Disc Brake Pad Wear Sensor - Rear
OE Quality 60-Day Returns
Global Parts

Global Parts 1813484 Disc Brake Pad Wear Sensor - Rear

Brand Global Parts 1813484
Position Rear
Terminal Type Pin
Wire Quantity 2
Connector Shape Oval
Terminal Quantity 2
Connector Gender Male
Terminal Gender Female
Wiring Harness Included Yes
Fits Porsche · 5 vehicles

Direct replacement. Fits as a brake wear sensor with accurate, reliable detection.

Pin terminals. Two-wire, oval connector design for a secure electrical connection.

Harness included. Comes with wiring harness for easier installation.

Cross-references Standard Ignition PWS200, 2BWS0086 and 993 612 365 01 for the same application. See all 8.

$18.50Free shipping
In stock · usually ships same day before 1pm CST
Step 1 — Confirm fitment
Free return shipping if it doesn't fit when you check fitment here first.

Select your vehicle to confirm fitment
Verify this part fits before purchasing — free returns if it doesn't
Step 2 — Quantity
Disc Brake Pad Wear Sensors are typically replaced in pairs, axle by axle.
Order total $18.50
Free shipping to the continental U.S.
Free returns within 60 days if it doesn't fit when fitment is verified.
Not what you need? See all Disc Brake Pad Wear Sensor options

Brake Wear Sensor for Porsche 911 Rear

Global Parts 1813484 is a direct replacement disc brake pad wear sensor for 1994-1998 Porsche 911 rear applications. It monitors brake pad thickness and provides a wear alert when the pads reach service limits, helping maintain consistent braking performance.

  • Direct replacement brake pad wear sensor
  • Fits 1994-1998 Porsche 911, rear
  • Pin terminal type with 2-wire design
  • Oval connector shape with male connector and female terminals
  • Wiring harness included
  • Built for brake wear detection on rear brake systems

Fitment and Application Details

This Global Parts brake wear sensor 1813484 is made for rear brake wear monitoring on Porsche 911 models from 1994 through 1998. It is a fit-focused replacement for drivers searching for a rear brake pad wear sensor for Porsche 911, 1994-1998, or a direct replacement brake wear sensor for Porsche 911 rear brakes.

The sensor uses a 2-wire layout with pin terminals, an oval connector, and a male connector body with female terminals. These details matter when matching the original brake wear sensor connection on the vehicle. This part cross-references Standard Ignition PWS200 for the same application.

What This Sensor Helps Address

  • Brake pad wear warning light staying on
  • Failed or damaged rear brake wear sensor
  • Intermittent brake wear signal from worn wiring or connector issues
  • Loss of brake pad thickness monitoring on the rear axle
  • Need for a direct replacement sensor during brake service

Installation Notes and Tips

Inspect the rear brake pad wear circuit, connector condition, and routing before installation. Confirm the connector shape, terminal count, and wire configuration match the original sensor on the vehicle. Replace the sensor during brake pad service if the existing unit is worn, damaged, or triggered by pad wear.

Quality Assurance

Global Parts 1813484 is engineered as a direct replacement brake wear sensor for accurate wear detection on supported Porsche applications. It is built to restore brake pad monitoring on 1994-1998 Porsche 911 rear brake systems.

Related reading

This part fits 5 vehicles
Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
YearMakeModelLitersCylindersPositionNotes
1998Porsche9113.6LH6Rear—
1997Porsche9113.6LH6Rear—
1996Porsche9113.6LH6Rear—
1995Porsche9113.6LH6Rear—
1994Porsche9113.6LH6Rear—
Directly replaces or cross-references 8 part numbers
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.
Standard Ignition — PWS2002BWS0086993 612 365 01ES114956SU13030URO-004625WK248WS400