InMotion WS1955 Wheel Seal - Rear, Rear Inner or Rear Outer

Wheel Seal for Rear Differential Applications

The InMotion WS1955 wheel seal is built for rear differential sealing where keeping lubricant in and contaminants out matters. Made with nitrile sealing surfaces and a durable metal case, it supports a tight seal for vehicles that need dependable protection at the axle end.

Compatible with a wide range of Toyota, Volvo, Dodge, and Hyundai rear axle applications, including Toyota Corolla, Toyota Celica, Volvo 740, and Dodge Colt models. The WS1955 is sized at 52 x 65 x 9 and is intended for precise fitment in rear inner and rear outer positions listed below.

• Nitrile sealing surface material for resistance to oil and contamination exposure
• 52 x 65 x 9 external markings for identification and fit verification
• Inside diameter: 51.6 mm / 2.03 in
• Outside diameter: 65.2 mm / 2.57 in
• Shaft diameter: 52 mm / 2.047 in
• Housing bore: 65 mm / 2.559 in
• Seal case material: AISI 1070
• Spring material: SAE 1008

Fitment Details

• Fits 1991-1997 Toyota Previa, rear outer.
• Fits 1991-1995 Volvo 940, rear inner.
• Fits 1994 Volvo 960, rear inner, with 65.2mm outside diameter.
• Fits 1990-1993 Volvo 240, rear inner.
• Fits 1992-1993 Volvo 960, rear inner.
• Fits 1992 Volvo 740, rear inner, Electronic Traction Control.
• Fits 1986-1988 Volvo 740, rear inner, Electronic Traction Control.
• Fits 1989-1991 Volvo 740, rear inner, with Electronic Traction Control.
• Fits 1989-1990 Dodge Colt, rear inner.
• Fits 1984-1989 Toyota Van, rear.
• Fits 1983-1987 Hyundai Pony, rear.
• Fits 1987 Hyundai Stellar, rear, with MIP Axle.
• Fits 1986-1987 Toyota Corolla, rear.
• Fits 1984 Toyota Corolla, rear.
• Fits 1978-1987 Toyota Cressida, rear.
• Fits 1986-1987 Volvo 760, rear inner, Electronic Traction Control.
• Fits 1987 Volvo 780, rear inner, Electronic Traction Control.
• Fits 1985-1986 Hyundai Stellar, rear, MIP Axle.
• Fits 1985 Toyota Celica, rear, with Semi-Float Axle.
• Fits 1985 Toyota Corolla, rear, with 0.354in width.
• Fits 1983-1985 Volvo 760, rear inner.
• Fits 1983-1984 Toyota Celica, rear, Semi-Floating.
• Fits 1984 Volvo DL, rear inner.
• Fits 1984 Volvo GLE, rear inner.
• Fits 1978-1983 Dodge Challenger, rear.
• Fits 1976-1982 Toyota Celica, rear.
• Fits 1973-1982 Toyota Corona, rear.
• Fits 1971-1980 Dodge Colt, rear.

What This Seal Helps Address

• Gear oil seepage at the differential pinion or axle seal area
• Contamination from road debris, dust, and moisture entering the seal zone
• Wear-related sealing loss in older rear axle assemblies
• Noise or driveline issues caused by low lubricant levels from leaks
• Service replacement needs on Toyota Corolla, Toyota Celica, Volvo 740, and Dodge Colt rear axle setups

Installation Notes

Verify the seal dimensions, housing bore, and shaft diameter before installation. Clean the sealing surface and inspect the axle or pinion area for scoring, corrosion, or wear that could affect seal life. This part number, WS1955, should be matched to the exact rear inner or rear outer position listed for the vehicle.

For fitment confirmation, compare the application notes carefully on Volvo models with Electronic Traction Control and Toyota applications with semi-floating or semi-float axle notes. This part cross-references no listed part numbers in the provided data.

Quality Assurance

InMotion manufactures this seal with nitrile sealing material, an SAE 1008 spring, and an AISI 1070 seal case to support consistent sealing performance in driveline service. The WS1955 is built for precise dimensional control and dependable use in the listed rear axle applications.