/live/media/9R/9R_421003_Fro.jpg)
PWR 42-1003 Rack and Pinion Assembly
| Brand | PWR 42-1003 |
|---|---|
| End To End Length | 1359 |
| Gasket Or Seal Included | Yes |
| Grade Type | Regular |
| Inlet Line Fitting Diameter | 16 |
| Inlet Line Fitting Gender | Female |
| Inner Tie Rods Included | Yes |
| Mounting Brackets Included | Yes |
| Mounting Hardware Included | No |
| Mounting Hole Quantity | 2 |
| Outer Tie Rods Included | Yes |
| Outlet Line Fitting Diameter | 14 |
| Outlet Line Fitting Gender | Female |
| Steering Input Shaft Diameter | 16.7 |
| Steering Input Shaft Spline Quantity | 36 |
| Total Turns Lock To Lock | 3.2 |
| Type | Hydraulic |
| Fits | Hyundai · 6 vehicles |
Direct fit. Makes installation easy with a straightforward replacement.
Hydraulic design. Delivers responsive steering performance with a proven rack and pinion setup.
Tested for function. Each unit is checked for leaks, pressure, noise, and operation.
Cross-references Cardone Reman 26-2411, 577002D000 and 3130209 for the same application. See all 3.
PWR 42-1003 Rack and Pinion for Hyundai Elantra
PWR 42-1003 is a hydraulic rack and pinion assembly for the 2001-2006 Hyundai Elantra. It is built as a direct-fit replacement to simplify installation and restore steering response on the Hyundai Elantra platform.
This rack and pinion assembly includes inner tie rods, outer tie rods, mounting brackets, and seals. It is USA Engineering Approved and each unit is tested for leaks, pressure, noise, and function before release.
Key Features
- Hydraulic rack and pinion assembly
- Direct-fit design for easier installation
- Includes inner tie rods and outer tie rods
- Mounting brackets included
- Gasket or seal included
- 36-spline steering input shaft
- 3.2 turns lock to lock
- Female inlet and outlet line fittings
- Fits 2001-2006 Hyundai Elantra
Detailed Description
Built for steering service on the Hyundai Elantra, PWR 42-1003 replaces the hydraulic rack and pinion assembly with a direct-fit unit that matches the vehicle’s steering layout. The assembly measures 1359 end to end, uses a 16.7 mm steering input shaft diameter, and features 16 mm inlet and 14 mm outlet line fittings with female ends. PWR 42-1003 is a practical choice when restoring steering feel, correcting hydraulic steering issues, or replacing a worn rack on 2001-2006 Hyundai Elantra models. This part cross-references Cardone Reman 26-2411 for the same application.
Common Problems This Part Can Address
- Steering play or loose steering feel
- Hydraulic fluid leaks from the rack assembly
- Noise during steering input
- Uneven or inconsistent steering response
- Wear in the rack, pinion, or tie rod components
Installation Notes and Tips
Verify the steering input shaft spline count, line fitting sizes, and mounting points before installation. Because mounting hardware is not listed as included, reuse or source the required hardware as needed. After installation, bleed the hydraulic steering system and inspect for leaks, proper assist, and centered steering wheel position.
Quality Assurance
PWR states that its pumps, racks, and gears are tested for leaks, pressure, noise, and function, and this unit is USA Engineering Approved.
| Year | Make | Model | Liters | Cylinders | Position | Notes |
|---|---|---|---|---|---|---|
| 2006 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| 2005 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| 2004 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| 2003 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| 2002 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| 2001 | Hyundai | Elantra | 2.0L | L4 | N/A | — |
| No rows match your filter. | ||||||