/live/media/9R/9R_422204_Fro.jpg)
PWR 42-2204 Rack and Pinion Assembly
| Brand | PWR 42-2204 |
|---|---|
| End To End Length | 1208 |
| Gasket Or Seal Included | Yes |
| Grade Type | Regular |
| Inlet Line Fitting Diameter | 12 |
| Inlet Line Fitting Gender | Female |
| Inner Tie Rods Included | Yes |
| Mounting Brackets Included | Yes |
| Mounting Hardware Included | No |
| Mounting Hole Quantity | 2 |
| Outer Tie Rods Included | No |
| Outlet Line Fitting Diameter | 11.12 |
| Outlet Line Fitting Gender | Female |
| Steering Input Shaft Diameter | 16.8 |
| Total Turns Lock To Lock | 3.25 |
| Type | Hydraulic |
| Fits | Hummer · 4 vehicles |
Direct fit. Makes installation easy with a straightforward replacement design.
Hydraulic design. Delivers responsive steering performance with a proven fluid-powered setup.
Tested for leaks. Each unit is checked for pressure, noise, and function before release.
Cross-references ACI 361316, Maval 95486M and 221117 for the same application. See all 5.
PWR 42-2204 Rack and Pinion for Hummer H3
PWR 42-2204 is a hydraulic rack and pinion assembly built for direct-fit replacement service. It is engineered for the 2006-2008 Hummer H3 with a 14mm diameter tie rod, making it a focused solution for steering repair on this application.
For buyers searching for a Hummer H3 rack and pinion assembly, this unit is built around the original steering geometry and connection points. The PWR 42-2204 is 100% tested for leaks, pressure, noise, and function before release.
Key Features
- Hydraulic rack and pinion assembly
- Direct-fit design for easier installation
- Fits 2006-2008 Hummer H3, with 14mm diameter tie rod
- Includes inner tie rods
- Mounting brackets included
- Gasket or seal included
- USA engineering approved
- End-to-end length: 1208
- Lock-to-lock turns: 3.25
- Steering input shaft diameter: 16.8
Detailed Description
The PWR 42-2204 rack and pinion assembly is a hydraulic steering component intended for direct replacement on the 2006, 2007, and 2008 Hummer H3. It uses female inlet and outlet line fittings, includes inner tie rods, and is supplied with mounting brackets for a cleaner service replacement. This part number, 42-2204, is built to match the steering system requirements of the listed Hummer H3 application.
This part cross-references ACI 361316 for the same application. It also cross-references Maval 95486M for the same application.
Common Steering Issues It Can Address
- Excessive steering play or loose steering feel
- Fluid leakage from the rack and pinion assembly
- Noise during steering input
- Uneven or inconsistent steering response
- Wear-related steering performance loss on a Hummer H3
Installation Notes and Tips
Verify the vehicle uses the 14mm diameter tie rod specification before installation. Confirm line fitting sizes, steering shaft diameter, and mounting points against the original unit before removal. Because mounting hardware is not included, reuse or source the required hardware as needed for the vehicle. After installation, perform a full alignment and inspect the hydraulic system for leaks and proper steering operation.
Quality Assurance
PWR states that its pumps, racks, and gears are tested for leaks, pressure, noise, and function. The manufacturer also identifies this unit as USA engineering approved.
| Year | Make | Model | Liters | Cylinders | Position | Notes |
|---|---|---|---|---|---|---|
| 2008 | Hummer | H3 | 5.3L | V8 | N/A | With 14mm Diameter Tie Rod |
| 2008 | Hummer | H3 | 3.7L | L5 | N/A | With 14mm Diameter Tie Rod |
| 2007 | Hummer | H3 | 3.7L | L5 | N/A | With 14mm Diameter Tie Rod |
| 2006 | Hummer | H3 | 3.5L | L5 | N/A | With 14mm Diameter Tie Rod |
| No rows match your filter. | ||||||