Standard Ignition KS234 Ignition Knock (Detonation) Sensor - Left

Ignition Knock Sensor for Audi and Volkswagen

Standard Ignition KS234 is an ignition knock sensor built for direct replacement on select Audi and Volkswagen applications. It uses a 3-terminal, plug-in oval connector with a bolt-mount attachment and a mix of plastic and metal construction for OE-style fitment.

• Part number: KS234
• Ignition knock (detonation) sensor for emission control systems
• Direct attachment method with bolt-mount installation
• 3 terminals, female connector, male blade terminals
• Oval, plug-in connector design
• Material: plastic and metal
• Fits Audi R8, RS5, A8 Quattro, A6 Quattro, S5, Q7, RS4, and Volkswagen Touareg and Phaeton applications listed below

Fitment and application details

Standard Ignition KS234 is used to monitor engine knock so the engine control system can adjust timing based on detonation feedback. This helps maintain proper combustion control on select Audi R8, Audi A8 Quattro, and Volkswagen Touareg applications, along with other listed Audi and Volkswagen models from 2004-2015.

This part cross-references OE-style numbers such as 077905377E and SU14137 for the same application. The KS234 reference is also useful when verifying the correct knock sensor for Audi R8, Audi RS5, and Audi Q7 fitments with brown connector or harness-length notes.

• Fits 2014-2015 Audi R8, N/A, Brown; Cyl. 3-4, 7-8
• Fits 2013-2015 Audi RS5, N/A, Brown; Cyl. 3-4
• Fits 2011-2012 Audi A8 Quattro, N/A, Brown; 500mm Harness; Cyl. 3-4, 7-8
• Fits 2009-2012 Audi S5, N/A, Brown; Cyl. 3-4, 7-8
• Fits 2009-2010 Audi Q7, N/A, Brown; Cyl. 3-4, 7-8
• Fits 2009-2010 Audi A6 Quattro, N/A, Brown; 500mm Harness
• Fits 2009 Audi R8, N/A, Brown; Cyl. 3-8
• Fits 2009 Audi A6 Quattro, N/A, 500mm Harness; Cyl. 3-4, 7-8
• Fits 2007-2009 Audi A8 Quattro, N/A, 500mm Wire
• Fits 2007-2009 Volkswagen Touareg, N/A, 500mm Wire
• Fits 2007-2008 Audi A6 Quattro, N/A, 345mm Wire
• Fits 2007-2008 Audi Q7, N/A, 345mm Wire
• Fits 2007-2008 Audi RS4, N/A, Brown; 345mm Wire
• Fits 2006 Audi A8 Quattro, N/A, Brown
• Fits 2006 Volkswagen Phaeton, N/A, 500mm Wire
• Fits 2005 Audi A8 Quattro, Left, w/ Brown Connector
• Fits 2004-2005 Volkswagen Phaeton, N/A, w/ Brown Connector; 500mm Wire
• Fits 2004 Audi A8 Quattro, Left, Brown

Common issues this sensor addresses

• Knock sensor fault codes related to detonation monitoring
• Engine timing control problems caused by inaccurate knock feedback
• Rough running or reduced performance tied to sensor signal issues
• Check engine light concerns on supported Audi and Volkswagen models
• Connector or harness mismatch when replacing the original sensor

Installation notes and quality

Verify the connector style, terminal count, harness length, and cylinder-bank notes before installation. This KS234 sensor uses a direct bolt-mount design and a single oval plug-in connector, so matching the OE routing and mounting location is important for proper installation on Audi and Volkswagen engines.

Standard Ignition supplies emission control and engine management components for service replacement use. KS234 is built to match the listed application details for accurate fitment on the vehicles shown above.