Timken 3732S Manual Transmission Input Shaft Seal - Front

Timken 3732S Manual Transmission Input Shaft Seal

The Timken 3732S manual transmission input shaft seal is built for front-position applications that need reliable lubricant retention and contamination control. It is a direct-fit sealing component for a wide range of Chrysler, Dodge, Plymouth, and select GM vehicles with manual transmission service needs.

Key Features

• Precision sealing design helps keep transmission lubricant inside the case and contaminants out
• Reinforced outer case resists installation damage and adds durability
• Ribbed rubber inner diameter helps seal minor spindle imperfections and promotes positive seating
• Internal contamination exclusion system helps block debris that can lead to leakage
• Vent holes allow lubricant flow around the seal lip to reduce heat buildup

Application Details

Compatible With front manual transmission service on vehicles such as the 1995-1999 Chrysler Sebring, front; 1995-1999 Plymouth Neon, front; and 1996-2000 Plymouth Breeze, front. This part cross-references CSF 10583 for the same application. Timken 3732S is also used across many front-position manual transmission applications, including Dodge Caravan, Dodge Daytona, Dodge Shadow, Plymouth Sundance, Chrysler LeBaron, and Chevrolet Cavalier fitments listed below.

• Fits 1996-2000 Plymouth Breeze, Front
• Fits 1995-1999 Chrysler Sebring, Front - Manual Transmission Differential Bearing and Race Set Fits A578 Transmission Models
• Fits 1995-1999 Plymouth Neon, Front - Manual Transmission Differential Bearing and Race Set Fits A578 Transmission Models
• Fits 1992-1994 Dodge Caravan, Front
• Fits 1984-1990 Dodge Caravan, Front
• Fits 1987-1994 Plymouth Sundance, Front
• Fits 1983-1993 Chrysler LeBaron, Front
• Fits 1984-1993 Dodge Daytona, Front
• Fits 1991-1993 Dodge Spirit, Front
• Fits 1989 Dodge Spirit, Front
• Fits 1989-1993 Plymouth Acclaim, Front
• Fits 1987-1992 Dodge Shadow, Front
• Fits 1981-1989 Dodge Aries, Front
• Fits 1985-1989 Dodge Lancer, Front
• Fits 1981-1989 Plymouth Reliant, Front
• Fits 1983-1988 Dodge 600, Front
• Fits 1982-1987 Buick Skyhawk, N/A
• Fits 1982-1987 Chevrolet Cavalier, Front
• Fits 1983-1987 Dodge Charger, Front
• Fits 1982-1987 Oldsmobile Firenza, N/A
• Fits 1987 Pontiac 6000, Front
• Fits 1984 Pontiac 6000, Front
• Fits 1984-1986 Chevrolet Celebrity, Front
• Fits 1984-1986 Chrysler Laser, Front
• Fits 1986 Pontiac Sunbird, Front
• Fits 1980-1985 Buick Skylark, Front
• Fits 1985 Cadillac Cimarron, Front
• Fits 1982 Cadillac Cimarron, Front
• Fits 1984-1985 Chevrolet Citation II, Front
• Fits 1984-1985 Pontiac Fiero, Front
• Fits 1984-1985 Pontiac J2000 Sunbird, Front
• Fits 1982-1984 Pontiac Phoenix, Front
• Fits 1980-1983 Chevrolet Citation, Front
• Fits 1982-1983 Pontiac J2000, Front

Common Problems This Seal Addresses

• Transmission fluid seepage at the input shaft area
• Debris intrusion into the manual transmission housing
• Seal wear caused by heat buildup and lubricant breakdown
• Leakage from minor shaft surface imperfections
• Damage from installation on older transmission cases

Installation Notes

Inspect the input shaft and seal bore before installation, and clean all mating surfaces thoroughly. Verify the seal is oriented correctly for the transmission design and press it in evenly to avoid distortion. For best results, replace a worn or damaged seal during transmission service rather than reusing an old sealing component.

Quality Assurance

Timken seals use reinforced construction, contamination exclusion features, and vented sealing design to support consistent operation in manual transmission service.