Timken HA590120 Wheel Bearing and Hub Assembly - Rear
OE Quality 60-Day Returns
Timken

Timken HA590120 Wheel Bearing and Hub Assembly - Rear

Brand Timken HA590120
Position Rear
Fits Mitsubishi · 7 vehicles

OE-developed testing. Controls design, materials, and manufacturing for consistent performance.

Low runout design. Reduces noise and vibration while improving braking performance.

Premium seals. Reinforced construction helps prevent contamination and extend seal life.

Cross-references MOOG Hub Assemblies 512291 and SKF BR930414 for the same application. See all 2.

$137.13Free shipping
In stock · usually ships same day before 1pm CST
Step 1 — Confirm fitment
Free return shipping if it doesn't fit when you check fitment here first.

Select your vehicle to confirm fitment
Verify this part fits before purchasing — free returns if it doesn't
Step 2 — Quantity
Order total $137.13
Free shipping to the continental U.S.
Free returns within 60 days if it doesn't fit when fitment is verified.
Not what you need? See all Wheel Bearing and Hub Assembly options

Timken HA590120 Rear Hub Assembly

The Timken HA590120 wheel bearing and hub assembly is built for rear applications on select Mitsubishi Endeavor models. It combines OE-developed testing, precision bearing construction, and integrated ABS sensing to support stable wheel speed monitoring, reduced noise, and consistent braking feel.

  • Rear wheel bearing and hub assembly for driven applications
  • 25 spline quantity, 5 wheel studs, and 4 flange bolt holes
  • 4.500 in. bolt circle diameter and 114.30 mm bolt circle diameter
  • Hub pilot diameter: 3.465 in. / 88.00 mm
  • Wheel pilot diameter: 2.638 in. / 67.00 mm
  • Brake pilot diameter: 2.717 in. / 69.00 mm
  • Flange offset: 2.331 in. / 59.20 mm
  • ABS sensor is 100% tested for wheel speed monitoring

Built for Mitsubishi Endeavor Rear Fitment

Fits 2010-2011 Mitsubishi Endeavor, rear. Fits 2004-2008 Mitsubishi Endeavor, rear. The Timken HA590120 is a direct-fit rear hub assembly for Mitsubishi Endeavor models with the listed driven rear application, using premium bearings with refined internal geometry and surface finish to support load capacity and bearing life. Low runout helps reduce vibration and noise while supporting more consistent braking performance. This part cross-references MOOG Hub Assemblies 512291 and SKF BR930414 for the same application.

Common Issues This Part Addresses

  • Rear wheel bearing noise or growling
  • Wheel vibration caused by hub runout
  • ABS warning light from wheel speed sensor signal issues
  • Uneven braking feel related to hub wear
  • Excessive play at the rear wheel hub

Installation Notes and Tips

Verify rear fitment by matching the vehicle year, Mitsubishi Endeavor model, and driven rear application before installation. Confirm spline count, bolt circle diameter, hub pilot diameter, and flange offset against the original part to ensure proper alignment. Inspect the mounting surface, axle interface, and ABS connector condition during replacement so the new hub seats correctly and the wheel speed signal remains stable.

Quality Assurance

Timken uses OE-developed testing to control the design, materials, and manufacturing process for hub bearing assemblies. The HA590120 is built with premium seals, precision-profile bearings, and a tested ABS sensor to support consistent performance in rear wheel bearing and hub service.

Related reading

This part fits 7 vehicles
Always verify fitment with your vehicle's VIN if unsure. Submodel & trim restrictions may apply.
YearMakeModelDrive TypePositionNotes
2011MitsubishiEndeavorAWDRear—
2010MitsubishiEndeavorAWDRear—
2008MitsubishiEndeavorAWDRear—
2007MitsubishiEndeavorAWDRear—
2006MitsubishiEndeavorAWDRear—
2005MitsubishiEndeavorAWDRear—
2004MitsubishiEndeavorAWDRear—
Directly replaces or cross-references 2 part numbers
Cross-reference numbers are provided for identification purposes only. Always confirm fitment before ordering.
MOOG Hub Assemblies — 512291SKF — BR930414