/live/media/SA/SA_FD8060_Fro.jpg)
TrakMotive FD-8060 CV Axle Shaft - Front Right
| Brand | TrakMotive FD-8060 |
|---|---|
| Position | Front Right |
| Abs Ring Tooth Count | 50 |
| Abs Ring Type | Toothed |
| Abs Tone Ring Included | Yes |
| Axle Nut Head Type | Hex |
| Axle Nut Height (in) | 4/5 |
| Axle Nut Height (mm) | 20 |
| Axle Nut Hex Size (in) | 1 1/6 |
| Axle Nut Hex Size (mm) | 29.4 |
| Axle Nut Included | Yes |
| Axle Nut Length (in) | 1 1/3 |
| Axle Nut Length (mm) | 34 |
| Axle Nut Locking Type | Self-Lock |
| Axle Nut Thread Size | M20*1.5 |
| Boot Material | Neoprene |
| Inboard Joint Type | Male |
| Inboard Shaft Connection Style | Male |
| New Or Remanufactured | New |
| Number Of Inboard Splines | 35 |
| Number Of Outboard Splines | 26 |
| Outboard Joint Type | Conventional |
| Outboard Shaft Connection Style | Conventional |
| Overall Compressed Length (in) | 28.27 |
| Overall Compressed Length (mm) | 718 |
| Product line | CV Axle Shaft |
| Fits | Ford · 4 vehicles |
ABS tone ring included. Toothed ring helps maintain reliable wheel-speed signal output.
Neoprene boot material. Flexible construction helps protect the joint from dirt and moisture.
New assembly. Ready-to-install CV axle shaft with axle nut included.
Cross-references Anchor 9322, Cardone New 66-2069 and Cardone Reman 60-2069 for the same application. See all 22.
CV Axle Shaft for Ford Windstar Front Right
TrakMotive FD-8060 is a new CV axle shaft for the front right position on 1995-1998 Ford Windstar models. It is built for direct replacement service with the correct spline counts, ABS tone ring, and included axle nut details for a proper driveline repair.
Key Features
- Fits 1995-1998 Ford Windstar, front right
- New CV axle shaft from TrakMotive
- Overall compressed length: 28.27 in. (718 mm)
- Inboard connection: male; outboard connection: conventional
- 35 inboard splines and 26 outboard splines
- ABS tone ring included with 50-tooth toothed ring
- Neoprene boot material for driveline protection
- Axle nut included with M20 x 1.5 thread, hex head, self-lock design
- TrakMotive FD-8060 cross-references Cardone New 66-2069 and Anchor 9322 for the same application
Product Details
This TrakMotive CV axle shaft is engineered for the front right side of the Ford Windstar and matches the listed application with the correct compressed length, spline counts, and ABS hardware details. The FD-8060 is a new axle assembly, not remanufactured, and is intended for vehicles that require a toothed ABS ring and a conventional outboard joint. TrakMotive’s CV axle shaft line focuses on direct-fit driveline replacement parts, and this application-specific design helps simplify selection for 1995-1998 Ford Windstar front right axle service.
Common Repair Uses
- Replacing a worn or noisy front right CV axle on a 1995-1998 Ford Windstar
- Addressing clicking or popping during turns caused by CV joint wear
- Correcting vibration from a damaged or imbalanced axle shaft
- Restoring driveline function after torn boots or grease loss
- Repairing ABS-related axle issues when the tone ring is part of the original setup
Installation Notes
Verify the vehicle’s front right application, spline count, and axle length before installation. Confirm whether the vehicle uses ABS and compare the tone ring configuration to the original part. The included axle nut uses an M20 x 1.5 thread and a self-lock design, so torque specifications and service procedures should follow the vehicle manufacturer’s recommendations.
Quality Assurance
TrakMotive lists this axle shaft as a new part and notes ISO 9001:1007 and TS 16949:2009 certification for the company. The FD-8060 also carries a limited lifetime warranty. Fits 1995-1998 Ford Windstar, front right.
| Year | Make | Model | Position | Notes |
|---|---|---|---|---|
| 1998 | Ford | Windstar | Front Right | CV Axle Shaft |
| 1997 | Ford | Windstar | Front Right | CV Axle Shaft |
| 1996 | Ford | Windstar | Front Right | CV Axle Shaft |
| 1995 | Ford | Windstar | Front Right | CV Axle Shaft |
| No rows match your filter. | ||||